All of a sudden unable to connect to a home network on XP

Similar Questions

• Windows 7 wireless connection problem: unable to connect to my home network

  Hello

  I just got a Dell laptop that is running Windows 7.  However, when I try to connect to my home network it impossible apperantly.  When I select "Troubleshoot Proplems" I get "Troubleshooting cannot identify the problem."

  I also already checked the pit of the Wireless Device Manager device.  It is activated and works perfectly.

  I know that the network is enabled and works because I'm typing this message on my desktop wireless capable of Windows XP.  In addition, my roommate is able to connect to the router and 'surf' the internet on their laptops.

  Therefore, I must assume that this problem is due to something in Windows 7.

  Hello Geoffrey.

  Have you tried to change the wireless channel that your router is running at? There may be interference that could prevent the internet connection:

  Take a look at step 6 in this article that give more details about it:

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx

  If you need assistance to change the settings of the specific router, you will need to contact your router manufacturer or your internet service provider.

• HP Photosmart B110a all-in-one: unable to connect to the home network wireless HP B110

  Hello

  I haven't used my printer for a while, so put in a new cartridge and tries to connect to my wireless network - domestic (the printer is next to the Belkins router). I've also upgraded to Windows 10 recently (also have a laptop with W7).

  The printer detects the SSID for wifi and after you type the router password wireless (WPA - PSK), it is NOT authenticated.

  The password IS CORRECT (100%) but it fails on the section of SECURITY depending on the display and the summary diagnosis. The message of the report is:

  Your route wireless requires a password WPA securitg. The password configured on your HP printer does not exactly. Run the network setup wireless for re0enter your network wireless WPA security passphrase.

  I need this because the only way I print is wireless email / I send it to the email address designated and it prints - it is not physically connected to any laptop / pc.

  I tried several times, including inputtingthe SSID manually, swtiching OFF etc.

  Please help - thank you in advance.

  Best regards

  Disable and remove temporarily the password on your routers SSID. Now try to connect to your SSID unsecured. Are you successful? If Yes, go back and add WPA2-AES with a password and try again.

• Unable to connect to the home network after you connect to the internet at Duke University

  Noteboook W7 Pro cannot reconnect to the network after you connect to the internet as a comments/visitor at Duke University.  The Duke system is predatory changes to my computer, and I can't fix it with the restoration of the system.   The home network is a Windows workgroup with most XP, no password only required machines.  This has happened in the past when the guest was an XP machine too, and then he had something to do with the DNS settings.  Cost me a lot of time and anguish and loss of productivity.

  Hello

  1. do you get an error message? If Yes, what is the exact full error message?

  2. are you able to connect to the internet?

  See the help article and check if it helps.

  Method 1

  Identify and resolve home network problems

  http://Windows.Microsoft.com/en-us/Windows7/identify-and-resolve-home-network-problems

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows#section_2

  Method 2: Check if the problem persists in the boot.

  To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to solve the problem by running the clean boot in Windows 7
  http://support.Microsoft.com/kb/929135

  Note: Once you have completed troubleshooting, perform the steps in the step 7: to reset the computer as usual.

  See also:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Let us know the status of the issue.

• Unable to connect to my wireless network

  I recently discovered that my wifi for vista would not connect to the internet even if the signal is 100% solid.

  My wireless House has a WEP encryption and it has already been saved on the laptop but since yesterday it ask me the WEP key when I try to connect it and wouldn't connect even if only the WEP pass has been entered correctly. The message that usually appears at the end is "windows is unable to connect, try the other network", even when I tried my companion's unsecured network.

  Here's what I did so far, but without success...

  I checked the Wireless driver from Device Manager and it works properly. I even try to update the driver and received a message that the driver is 2-update.

  Here's what I got when I tried to use "ipconfig/all".
  ..................................................
  Windows IP configuration

  Name of the host...: AZOU
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.
  ... DNS suffix search list: Belkin

  Wireless network connection Wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  Description...: Realtek RTL8187B Wireless 802. 11b / g 54Mbp
  s USB 2.0 network adapter
  Physical address.... : 00-22-5F-36-AE-19
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : Belkin
  Description...: Realtek RTL8102E Family PCI - E Fast Ethern
  and NIC (NDIS 6.0)
  Physical address.... : 00-1E-33-7A-3C-AE
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::1ad:202c:5412:8070% 10 (Preferred)
  IPv4 address...: 192.168.2.35 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: May 2, 2009 19:58:15
  End of the lease...: June 9, 2145 03:09:10
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DNS servers...: 192.168.2.1.
  194.168.4.100
  194.168.8.100
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : Belkin
  ... Description: isatap. Belkin
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  I can use the Ethernet cable to connect and this is killing me lol seriously... can anyone pls help me, I want to get this working wireless!

  Thank you

  Hello!

  What computer Toshiba laptop and OS do you have?

  In your case, I would check the Web from Toshiba site for an update of the BIOS:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Have you tried to reset the router? Unplug the AC adapter from the router, wait 5 or 10 minutes and then try again.
  Another laptop works on the router?

  Good bye

• Unable to connect to a wireless network - "the network card know driver or hardware related issues.

  Can someone help with the following problem please?

  I'm unable to connect to the wireless network.

  I have an Acer Aspire 5315 with an Atheros AR5007EG wireless adapter. This shows that "working properly" in the Device Manager. I tried to re - install the drivers for it constantly. They seem to everyone install ok but I still have the problem.

  The symptoms are...

  (1) if I try to set up a wireless connection, I get "unexpected error occurred". There is no useful looking for messages in the event viewer.

  (2) if I use "Diagnose and repair" I get "knows the network adapter driver or hardware related issues.

  I uninstalled everything which I think could be the cause of conflicts. I scanned for malware. I have run chkdsk and sfc. I have all the updates from Windows Update. I tried in Safe Mode with networking, but still get the same results.

  OS is Vista Home Basic 32-bit SP2.

  I would be grateful for any advice that might help solve this please.

  I have now re-installed Windows and everything works fine.  I still have no idea what caused the problem, or if it could have been set without a re - install.

  Thanks for the replies.

• Unable to connect to other wireless networks

  RE: Unable to connect to other wireless networks

  • My computer is a HP Pavilion dv7 1232nr Entertainment Center
  • My OS is Windows Vista 64 bit
  • I have installed many things over the past year, but know that at some point, I was able to get on free Wi - Fi in hotels

  I am able to connect to my network, but when I try to connect to others, I'm unable to do. I have their password and my computer SHOWS I have a connection, but actually I'm not. When I try to connect to the Internet, the server is not found. I called the support/supplier for the last network owner and he told me that even if I "thought" I was online, I really wasn't. He said that it is probably a router configuration for that person that does not correspond to my computer. As I was just visiting, of course I didn't mess with their router. This happened to me twice, with once the provider is the same as mine, but the only way I could get connected with a hard link.

  So far, the only thing I did is to see if I could connect to free wireless (municipal library) and was unsuccessful. I think the problem is with my settings, but am not sure. I have to be careful to change anything because I can't afford to lose my connection at home because my job depends on it.

  Any suggestions?

  Thanks for any advice you might be able to share.

  Hi, Pat:

  I am very confident that if you download and install the driver from the link below, your problem will be solved.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & CC = US & prodTypeId = 321957 & prodSeriesId = 3688868 & swItem = ob-99392-1 & mode = 3

  Paul

• Pavilion 14-ab051tx N4G24PA: unable to connect to any wireless network after the upgrade to Windows 10

  I recently bought a 14-ab-51tx Pavilion N4G24PA, this is my first laptop from HP, it comes with Windows already installed 8.1 and it worked fine.

  The thing is, I kind of get used to using Windows 10 on my previous laptop, so without further hesitation I upgraded to 64-bit Windows 10.

  Here's what I did wrong:

  Instead of update Windows 8.1 for Windows 10, I indeliberately he installed fresh, with couple of mouse clicks, I didn't realize that I also remove the recovery partition.

  I realized only after the installation process is complete, but then it was too late. I look forward to using my laptop with Windows 10 freshly installed inside to make some games just noticed that I couldn't connect to any network without wire, House or public. It recognizes my wifi at home, but the signal bar is bizarre, there is only 1 bar of signal even if the wireless router is only about 10 feet from him, so I checked my other computers and smartphones, but the signal on them is ridiculously high (full bar), it also detects another wireless network that are further away than my wireless router.

  But back to my HP laptop, I tried to connect to my home network despite the signal bar with the right entry security key, but it does not connect, it says "Cannot connect to the network".

  Tried updating drivers with HP Support Assistant and no luck, the problem persists, tried all the solution on the internet, int ip reset, reset winsock, checking and unchecking, always without success.

  Can someone help me please...

  Hello:

  The BOM indicates that your laptop comes with a Broadcom wireless card.

  Have you tried the last W10 driver for this card to support your PC and driver page?

  This package contains the Broadcom Wireless LAN drivers for the laptop models running a supported operating system. Broadcom wireless LAN drivers are required to activate the built-in Broadcom wireless LAN adapter.

  Exit the: December 17, 2015

  Version 7.35.317.0 Rev.A

  File name: sp74241.exe

• Satellite L650 - unable to connect to the public network (has no valid IP address)

  Hello

  Toshiba satellite L650 laptop computer (with windows 7 64-bit), I bought two days back and I'm unable to connect to the public network. Sometimes, it must be connected to the public network and after a few minutes it disconnects. I get the message "wireless network doesn't have a valid IP configuration him."

  I have visited many forums and did everything, but of no use.

  1. people with disabilities the tcp/ip V6 of the registry.
  2. the DHCP is enabled. With the help of the automatic IP (DHCP)
  3. also tried with a static IP configuration.
  4. uninstalled the antivirus provided with laptop computer (Norton).
  5 disabled the windows firewall.
  6. restored to factory settings.

  I called Toshiba Tech support as well and they have suggested that it may be a problem of H/W but I don't think that so that it can be hardware problem because sometimes he must be connected to the public network. Now I'm left with no option except return the laptop to Toshiba (I'm less interested in this because I know that sending laptop for replacement will be more frustrating).

  Can someone please give some other suggestions for this problem?

  Hey,.

  Can you connect to your home WIFI router correctly?

  If you have problems with the public network connection, you should ask the owner of these networks. Usually, there is always a contact, you can ask if you have any problems with the connection.

  What you can try is updated WLAN driver from Toshiba's official website:
  http://APS2.toshiba-tro.de/WLAN/

  If it doesn't work, ask the person contact I mentioned.

• All my iTunes music is on a disk hard Ext. connected to my home network through a router. Is it possible that devices that are part of my home network share iTunes can access the music on this disc hard Ext. without my laptop being on?

  All my iTunes music is on a disk hard Ext. connected to my home network through a router. Is it possible that devices that are part of my home network share iTunes can access the music on this disc hard Ext. without my laptop being on?

  Additional information: the laptop is what I used to install all the music, via iTunes, which is located on the external hard drive connected through home network router.

  Is it possible that devices that are part of my home network share iTunes can access the music on this disc hard Ext. without my laptop being on?

  Laughing out loud

• Satellite M100-221: unable to connect to the home WiFi AP

  Unable to connect to the home WiFi AP. Impossible to establish connection (when using intel software Bundle, connection hangs on the authentication step.
  When using the connection and windows engine, it connects 3 times will come down on "acquiring network address").

  I downloaded and installed the latest drivers and updates to the BIOS, but it does not solve the problem. Other computers with equivalent settings to connect without any problems.
  Wireless AP DLINK 1000AP + type b Wi - Fi.

  What is the problem?

  Hello

  When I have this kind of problems, sometimes by turning and the AP help.
  Or try to change the authentication or encryption settings.

  Good bye

• G5E22EA #A2N: unable to connect to the wifi network

  When I turn on the wifi in my HP Pavilion 15 laptop pc and try to connect to my network of your choice... it says "check and connection. After a minute, it says "cannot connect to this network '...

  I tried to use the other pc and smartphones to connect to my network of your choice via wifi and they connect successfully and I can use wireless net in other devices!

  Hello @Khaled-819.

  Thank you for your query,

  I understand that you are unable to connect to your wireless network, but other devices connect correctly.

  Have you ran the Windows troubleshooting tool?

  Did you run the Internet functionality and security in HP Support Assistant ?

  Here is a link to HP PC - troubleshooting wireless network and Internet (Windows 8) that should help you.

  If you are unable to connect I would test for a hardware failure.  You will locate network under the title of part.

  HP Notebook PC - detection of hardware failures (Windows, 10, 8)

  To say thanks for the reply please click the thumb up below.

  If you were now able to solve your problem please click on accepted the solution to help others.

• Unable to connect to the wireless network, error message "Windows could not finish repairing the problem because it is impossible to perform the following action. Renewal of your IP address.

  Original title: Unable to connect to the wireless network

  Unable to connect to the network wireless Toshiba Satellite A105 PC running Windows 7.  "Windows could not finish repairing the problem because it is impossible to perform the following action. Renewal of your IP address.  Works with Windows XP SP2, IE 8.00.6001.18702 file, I think that Version 3.  It has been installed on a disk provided by Microsoft after that old installation became corrupt (in the sense of Microsoft technical support.)  Before that, wireless network worked well.   (So unable to connect to the Internet for updates.)   Have tried to change the other settings and different messages acquired when it SHOWS that I am connected but cannot connect because of something to do with the certificate.  I don't remember what I did to try to solve this problem in the last days.

  I should add that I have tried the solutions of the previous forum on this topic, and none worked.

  Hi Marilynnla,

  Sorry to hear about the bad experience you encounter. Lets see if the network problem can somehow be archived.

  Read this article and follow the steps. Lets see if it helps in any way.

  How to troubleshoot wireless network connections in Windows XP Service Pack 2 (Works for Windows XP SP3 as well)

• I can connect to my home network, but all the other networks do not work...

  I can connect to my home network, but all the other networks do not work... Error window says:

  Windows could not connect to the (X)? network name?

  [Link] Solve problems

  [Link] Learn more about Internet connection problems

  I gave security, uninstalled reinstalled wireless - uninstall security firewall reinstall and not go...

  Windows 7

  Hello

   
  1. What network are you trying to connect to?
  2. You are not able to connect to the Internet?
  3. Are you able to connect to the other network with wired network?
   
  Try the methods provided and check.
   
  Method 1:
  Check out the link and follow the steps.
  What is network discovery?
  http://Windows.Microsoft.com/en-us/Windows7/what-is-network-discovery
   
  Method 2:
  Check out the link and run the troubleshooter.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  Method 3:
  Reset the TCP/IP and check. Check out the link and follow the steps.
  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357
  Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows
   
  Method 4:
  Check out the links and check out them.
  http://Windows.Microsoft.com/is-is/Windows7/cant-connect-to-a-network

  http://Windows.Microsoft.com/is-is/Windows7/view-and-connect-to-available-wireless-networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

• Unable to connect to internet home with Blackberry 8900 for windows 7

  Unable to connect to internet home with Blackberry 8900 to windows 7, error = a network cable is not plugged in correctly or may be broken, tried a different cable, same problem?

  Hello

  1. are you able to use the Blackberry 8900 on any other computer?

  2 have had any changes made to the computer before the show?

  Please follow the steps in the link.

  Support for attached modem use

  http://btsc.webapps.blackberry.com/btsc/viewdocument.do;jsessionid=55C4DA5CE489E53E47CDDDB9FA0C6A59?externalId=KB05178&sliceId=2&cmd=displayKC&docType=kc&noCount=true&ViewedDocsListHelper=com.kanisa.apps.common.BaseViewedDocsListHelperImpl

  If you are still experiencing a problem, I suggest you to contact Blackberry support team for assistance.

  http://supportforums.BlackBerry.com/T5/community-corner/BD-p/corner