All USB (2 & 3) drives does not connect. Tones play when I insert a USB key. Troubleshooting of Ran unsuccessfully.

Similar Questions

• My printer driver does not connect to my new laptop

  Original title: too old printer?

  My printer driver does not connect to my new laptop it says my hp7150 is a usb device that is older and may not work with usb 3 try usb 2?

  Hello

  You should be able to operate...

  Did you install the software for your printer, or just plug in?

  You can actually have more luck with the USB 2.

  I think your laptop would have at least a USB 2 port. Glance to one that is not blue...

• CD/DVD drive does not recognize or play regular music store bought CDs recognizes only RW and DVD.

  No error msg when disk is inserted it is a usual thing, then stops and the little light remains yellow on. Which will be normally blinks then turns off normally.  I removed and re-installed the disk drive, without effect.  He uses this only on a few CDs. Now, not in my collection will not be recognized / reading and seem to me that the drive just hangs.  When I check the drive, it says to insert the CD. Ugh someone? Thank you

  Use a CD/DVD cleaning disc to clean your car.  If it still not work properly while the reader probably does not and must be replaced.

  'ole pal' wrote in the new message: * e-mail address is removed from the privacy... *

  No error msg when disk is inserted it is a usual thing, then stops and the little light remains yellow on. Which will be normally blinks then turns off normally.  I removed and re-installed the disk drive, without effect.  He uses this only on a few CDs. Now, not in my collection will not be recognized / reading and seem to me that the drive just hangs.  When I check the drive, it says to insert the CD. Ugh someone? Thank you

• Windows 7 laptop does not connect to Wifi when the WPA2 security is Active

  I have a rather unusual problem that my Compaq CQ56 laptop not not connect to my router, ASUS RT-AC56U Wi - Fi when WPA 2 security is active on the router. With WPA2 is off, it connects without a problem. But, when I turn it on WPA2 on it will not connect. This problem persists even if I change the WPA2 authentication code. All other devices at home are able to connect with the wifi with WPA2 enbabled router, and this particular laptop was able to do so until very recently.

  Just to make sure that the adapter in the Compaq works, I just went to Starbucks and it connected to their wifi unsecured without problem.

  I was using a TP-Link Wireless Range extender on the home network, but it was deleted.

  I ran the network troubleshooting and Fix - It nothing works.

  I suspect that for my home network installation file was corrupted on this laptop and I would like to know if there is a way to remove, or edit this file and start from scratch. I have a Compaq laptop earlier generation linking problem now. So I'm pretty a connection file corrupted is the problem. Just need to know how to solve this problem.

  Thanks for any help!

  See this tutorial.

  http://www.SevenForums.com/tutorials/120670-wireless-network-remove.html

• External USB 250 GB HARD drive does not connect

  Hola everyone,

  A year ago I bought 2 this record.
  Now, the two (running on different stand-alone on Windows 2000) do not contact for the pc. The LED is red and blinking blue.

  The doesn´t of "fantastic" manual say anything.

  Any ideas out there?

  Hello

  I have no idea and I don't know what you're doing with your drives, but it will be interesting to know if you have tried to do something to solve this problem.

  Let moments hard drives without power and try to connect again.

• 2540 all-in One: 2540 printer does not connect via radio

  Dell Inspiron Windows 8.1 64bits, lesst of one year

  HP 2540 all in a Priner single, new, right out of the box

  Router NetGear WGR614 v9 (2008?)

  Unable to connect wireless.  OK, via the USB port.  Need a wireless connection.  Doctor Scan is without help.

  Who did. Thank you. I do not understand why IT worked, but it setting up wireless initially failed. It was VERY frustrating. I was ready to trash this abiut printer.

  P.S: it prints very well. Photos of ESP. My children and I are very impressed.

• Samsung tablet driver does not connect with my computer (windows 7)

  Hello I have a Windows 7 right and whenever I connect my Samsung galaxy tablet 3 USB it says device driver software was not successfully installed. I checked the updates, it didn't work, but I check the properties of the device it says error code 10

  Hello jasmine,.

  Thanks for posting your question on the Forum of the Microsoft community.
  1. If it works much earlier? If Yes, did you of significant changes to the computer before this problem?
  2. Have you tried to connect the tablet to another USB port on your computer?
  3. Are you able to connect the tablet to another computer?

  I understand that you get an error code 10 device when you plug your tablet computer. This error is due to some kind of unspecified driver or device problem. In your Windows Device Manager is not able to start the unit due to a driver-specific is not recognized. So, let's try a few steps to start in the right direction, diagnose the root cause and solve your problem.
  Method 1:
  Try to follow the steps described in the following link and check if the problem persists:
  FIX: "this device cannot start" error Code 10 in the Device Manager in Windows

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  Method 2:

  You can also download the Software Kies from Samsung for Windows that allows you to connect your phone to your personal computer, makes it easier for you to synchronize data between the devices.

  Samsung Kies 

  Hope this information is useful. If the problem persists, please post back your results for further assistance, we will be happy to help you.

• Computer laptop Lenovo G500 does not connect to wifi when I travel.

  I've had this problem since day one. A support person of Lenovo managed to connect when I first became aware of the issue, but it would not log the next time I was in a hotel. The support people with the service provider for the hotel wifi could not help me. Drivers have been checked, windows has been updated. Microsoft security essentials antivirus running. At home, I connect to internet through my ethernet cable.  I travel quite often and my laptop is useless, unless a wired connection is available. Help!

  Hi Mario,.

  I imagine the inconvenience that you are experiencing. I appreciate your efforts to resolve the issue. I will certainly help you in this matter.

  This problem can occur if authentication enable IEEE 802. 1 X for this network checkbox is enabled. If this box is checked, but there is no server to authenticate the connection is interrupted. If you turn on the wireless network connection, it disconnects again after a short period. This problem can also occur if Wi - Fi drivers are not updated properly, or due to changes in the network settings.

  Try these methods below and check.

  Method 1: run it Troubleshooting Internet connection problems.

  Try to run the Internet Connection Troubleshooter that can help you solve the problems with the internet connection.

  1. Press the "Windows + C" to activate the menu of charms or move the mouse to the bottom right of the screen and you will get the menu of charms.
  2. Click Search , and then select settings.
  3. Troubleshooting of type and select Troubleshooting.
  4. Click network and Internet , and then select Internet connections.
  5. Click Next to run the troubleshooter.

  If the problem persists, follow method 2.

  Method 2: Disable IEEE 802 authentication. 1 X.

  To disable authentication IEEE 802. 1 X, follow these steps:

  1. Click Start, type ncpa.cpl, and then press ENTER.

  2. Right click on your wireless network connection and then click Properties.

  3. Click the wireless networks tab.

  4. Under preferred networks, click your wireless network, and then click Properties.

  5. Click on the Authentication tab, click to clear the authentication enable IEEE 802. 1 X for this network check box and then click OK twice.

  If the problem persists, use method 3.

  Method 3:

  Follow the steps in the Microsoft help articles below:

  Why can't I connect to the Internet?

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

  Thank you

• I do not have a dail-up, it is Verizion DSL. Problem is router does not connect to internet when I try ti sign in to MSN

  There is a sign on the screen to access MSN Premium, homepage, e-mail, etc..  However, I click to connect and I have dial-up screen.  I don't have a dail up.  If I use explore to access the internet... it works.

  Hello

  I suggest that you post your question on the Forums of MSN, as the question are related to the MSN homepage.

  http://social.MSN.com/boards/

  It will be useful.

• Equium M50-164 does not connect to internet

  I bought this laptop 3 months ago, and the wireless internet worked well. Now all of a sudden, it does not connect to wireless internet, so that the pc downstairs. It will not connect also if I connect to the router directly, or even through your phone line ADSL modem.

  Any ideas on how to solve this problem?

  Hello

  Please check device manager if the card network and wireless card are recognized correctly.
  You have installed any 3rd software or have you changed something? Did you get any error messages? Please post more information.

  Good bye

• My CD/DVD drive does not work

  My CD/DVD drive does not work, he plays any kind of disc, I don't think that my computer recognizes that it has a DVD player that more, please help!

  See this knowledge base article http://support.microsoft.com/kb/982116/en-gb

  Remove spyware, etc., can often mess up some registry settings that make it seems that the CD / DVD ROM drive is defective.
  HTH
  Neil
  www.nwarwick.co.UK

• Canvio Plus 2.5 "1 TB external HARD drive does not work with USB 3.0

  I've had this drive for about a month.

  I am on Windows 7

  I can only operate by connecting to USB 2.0 ports. It is then visible in 'My Computer'.

  If I connect to USB 3.0, it turns on the case but does not appear in 'My Computer'.

  I tried it on all my USB ports 3.0 - up on one and two in the back of my case.

  I checked my BIOS and USB 3.0 is enabled.

  I tried to follow the suggestions in the user manual, but the drive does not appear in the management of so connected devices on USB 3.0, but it does when connected in USB 2.0.

  Any ideas?

  Hello

  As much as I know the Windows 7 system requires installation of additional USB 3.0 driver.

  Many laptops and computers use USB 3.0 driver that was released by Intel... it is because of Intel chipset...

  I guess that USB 3.0 is already installed, but probably you need to update the driver at least to the newest version...

• HP OfficeJet 4650: HP utility does not connect to my new portable printer HP OfficeJet 4650 of my connected USB MAC

  Utility HP does not connect to my new HP OfficeJet 4650 of my Mac connected usb portable printer.  I have to turn off the printer, printer and try again sometimes that works.

  Welcome @grizley1967.

  Thanks to their participation in Forums of HP! I see by your post that the HP utility connects to the printer. I will definitely do my best to help you.

  Make sure that the printer is connected directly to the Mac with the USB cable.

  Fix permissions of the drive on the Mac:

  Close all applications.

  In the Apple menu, click OK, click Applications, and then click utilities.

  Open disk utility.

  Select the startup disk in the list of volumes.

  Click the first aid tab.

  To verify permissions, click on verify disk permissions. To fix the permissions, click on repair disk permissions.

  Restart the computer.

  Reset the printing system:

  Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

  Click on the Apple icon and then click on System Preferences.

  Click on Printers & Scanners.

  Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.

  Click OK to confirm the reset.

  Type the name and the correct password.

  Click OK to reset the printing system.

  Then click on the sign to add the driver, highlight the printer +. (you may need to click the drop down menu to select the name of the printer) Then click the Add button.

  Feel free to click on the button 'Accept as Solution' and the 'Thumbs Up' for my help. Please let me know the results and if there is anything else I can help you. Thank you!

• Apparently, I got an automatic update of Windows XP. All of a sudden my computer does not connect to my HP Laserjet 1000 printer.

  All of a sudden my computer does not connect to my HP Laserjet 1000 printer. These work very well together for several years.

  Now all of a sudden I get a message that the computer cable is not connected.  I tried to charge the printer program.

  I unplugged and reconnect the cable to the computer, etc.. The system does not work.

  I learn by two other people, who have automatic updates of Windows, they had the same problem. We have a Kodak

  printer and the other has a Lexmark printer. This makes me think that the problem is in the updates of Windows.

  So, what should I do to fix this? I'm NOT a computer person and I'm confused.

  James

  Hello

  · The updates have been installed on the computer?

  You can follow the procedure from the following link: printers HP LaserJet - USB Devices closing work unexpectedly in Windows XP: http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=110&prodSeriesId=45674&prodTypeId=18972&prodSeriesId=45674&objectID=bpl11421

  You can also access: family of products HP LaserJet 1000 - Error Messages on the computer (PC): http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=110&prodSeriesId=240170&prodTypeId=18972&objectID=bpl11045

• Atheros AR9285 in CQ61-410US wireless network card does not connect to the Internet after the update of the adapter driver

  I have a Compaq Presario CQ61-410US (WA974UA) which is equipped with an Atheros AR9285 B/G/N wireless network adapter.   The laptop Internet access was fast and stable when using a Wi - Fi N.   Its pilot AR9285 was the initial version of the 8.0.0.172 factory.  But because there were so many subsequent driver updates, I've updated the display driver version from the support page 8.9.9.316 (sp48755.exe).  However, after updating the driver, I immediately lost Internet access.   The laptop is running Windows 7 Home Premium with Service Pack 1 and 64-bit.

  The driver seems to be installed OK, but it does not connect to the Internet.  Here is the status of the driver: 1) in Device Manager it appears OK and is presented as working properly.  (2) in the results of IPCONFIG/all, it there is no entry for the wireless adapter and without IP addresses are affected.  Here are the results of the IPCONFIG/all command:

  C:\Users\Karen>ipconfig/all

  Windows IP configuration

  Name of the host...: KarensLaptop
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Ethernet connection to the Local network card:
   
  State of the media...: Media disconnected
  Connection - a DNS suffix is specific. :
  Description...: Realtek PCIe FE Family Controller
  Physical address: 00-26 - 9th - JJ - 83 - 9 c
  DHCP active...: Yes
  Autoconfiguration enabled... Yes

  Tunnel adapter isatap. {E52D6F3E-5080 4B3B - 8BE7 - B7CFD7E137D1}:

  State of the media...: Media disconnected
  Connection - a DNS suffix is specific. :
  ... Description: Microsoft ISHTHP adapter
  Physical address: 00-00 - 00 - 00 - 00 - 00 - 00 - E0
  DHCP active...: No.
  Auto connection...: Yes

  Map of tunnel Teredo Tunneling Pseudo - Interface:

  State of the media...:...: media disconnected
  Connection - a DNS suffix is specific. :
  ... Description: Teredo Tunneling Pseudo - Interface
  Physical address.... : 00-00 - 00 - 00 - 00 - 00 - 00 - E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  C:\Users\Karen >

  (3) Trying to Connect through connections network does not a list of known available networks and instead says "not connected - no connection is available."

  I have read several messages from the HP Forum and tried a lot of things, including the installation of various updates driver later thanks to the version 10.0.0.222, but I still can't the driver to connect to the Internet.  I also changed my router "n" has only B/G as the AR9285 pilot has a history of problems with Wireless N.  Even back to the original driver version 8.0.0.172 provides an Internet connection.

  Any advice would be appreciated.

  Hello:

  I'm glad that you were able to restore your internet connection.

  I'd go with the latest driver HP vice one from another source.

  The only time wherever I go outside HP for wireless network drivers is if you have an Intel wireless card.

  My recommendation is to use the free MS Security Essentials antivirus/antispyware, which never interfere with how "things important works" on your PC, such as network connections.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=5201

  Your router with a hardware firewall and a software firewall Windows. I don't see the importance of adding other firewalls.

  Unless you have a lot of albums secret info on your PC that pirates would like to get my hands on, these fully functional security roadblocks are adequate for most of us.