back to white screen

Similar Questions

• white screen after that vista went on mode 'sleep'

  Hello

  My laptop started to have problems after going sleep mode hibernation recently. I run a Dell Vostro under Vista 32 bit. My big problem is that I can't test one of the solutions I found on the internet so far because even with a forced shutdown the laptop never start back. White screen. Nothing is ever displayed.
  Last time I went out that holding the key FN holding power. Then released. The screen came blue and memory tests and drive hard started. I let it run and no problem was found on the hardware side. After the tests were performed, the computer restarts and I press F8 to boot into safe mode. Everything went well for a week after this episode. I tried the "sleep mode" once again and it was as if nothing ever happens. Everything worked well.
  And now, it's happening once again. This time, the combination FN-power supply does not work. Nothing appears on the screen ever. The power button not blink or change color. The hard drive light turns on for 3 seconds only when I try to start. Then it's screen white and everything that I hear the laptop fan...
  Any idea of someone from the combination of keys to force start the laptop into a kind of safe mode?
  Thank you very much!!!

  So it seems that I have to respond to me :) Just in case someone goes nuts facing the same issue, find multiple options on the web 2007 update you this, change the configuration that say, start in SafeMode etc., here is what I found to get out of the black screen after a watch on my laptop. I hope this might help someone else:

  1. Open the housing by unscrewing all to access the battery (not easy, go slowly and carefully do not damage the fragile covers). I hope that your battery is more accessible than mine.
  2. Disconnect the battery cable (if you have my laptop Dell Vostro: first - raise the head end of the connector so you can exit the orange cable gently)
  3. At this point, the rear of the laptop is completely "naked".
  4. Unplug the power cable
  5. Press and hold the power button to laptop for 30 sec.
  6. Plug the power cable back (battery is always not connected)
  7. Press the FN key + power button for 1 second and release them both at the same time
  8. The DELL logo is displayed, and finally the screen is not black more! I need the pre-boot system assessment tests. I hope that you will have this screen also. I suggest that you run the tests. In my case, nothing was wrong with the hardware. This is a Windows problem.

  After this step, I was able to start in safe mode and play with the features of windows. Since I'm a busy mom and small business owner, I don't have time to assess what is wrong or even think to completely replace Windows on an old computer laptop 1 year part-time, so far. So I just canceled the sleep function for now.

  Good luck.
   

• After have logged you on you yahoo this am, my calendar and Notepad have disappeared. When I click on it I just get a white screen. I'm not very computer and need help getting them back.

  When I usually go in the mail from yahoo, there are an icon on the upper left side to access my calendar and a Notepad. They are both gone, but there is a field in the lower left corner that has the buttons. When I click on one or the other, I just get a white screen. I have not updated to Firefox to a new version and can't imagine what happened during the night.

  It sounds more as if it was a temporary problem with the site Web of Yahoo mail. At this point, my advice is to see if this gets fixed in a few hours. If not, please come back (in fact, FRY without worrying and let us know if your problem is resolved).

• I went to upgrade to El Capitan, it was last night. I have a blank white screen. I tried to turn off my computer, but when I turn it back on all that I get is a status bar that shows its about 3/4 downloaded and then it goes back to a blank white thyristo

  I tried to download El Capitan. Has started last night. all I have is a blank white screen. I stop my computor waited awhile and he turned his back. I work around a status bar indicating that it is about 3/4 full, then it goes back to a blank white screen?

  I had this problem too on my iMac (21.5 inch, late 2009) and I tried to restore to the previous version and then do the update again, but I got the same results.  I also tried to reinstall OS X option of the application of the utilities on the recovery disk that took a few hours but got the same results.  Finally, I tried to restart and make a secure boot (hold down the SHIFT key when the bell rang and rejection when the Apple shows up) and I was able to get the computer to boot.  When I logged in a window pops up saying "Complete Installation" and still had 6 min.  When he finally finished, I was an able to connect as usual and everything works fine now.   My mid 2009 Macbook Pro has no problems with the update but my iMac has been a pain.  I hope this helps you and anyone else who may have this problem.

  iMac (21.5 inch, late 2009)

• Windows XP 07 login I get the black and white screen where is safe mode option and then just loop it back to the same screen.

  When I powered on my Windows O.S. ' 07 I got the black and white screen where the option of safe mode and when I entered beginning that normally he just came back to the same screen of the suggestions?

  Hi RudyNY,

  1. you have Windows 7 or Windows XP installed on the computer?

  2. you receive an error during the process of loop?

  3. did you of recent changes on the computer?

  4 when was the last time it was working fine?

  Check to see if you can boot into safe mode in the Advanced menu options and the last good known Configuration.

  http://www.Microsoft.com/windowsxp/using/Setup/support/nostart.mspx

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

• Wanted: White screen after 10 Windows Update - problem even when back in windows 8.1

  Hello

  I've updated to windows 10 and after a few hours, the main screen of my laptop went blank but my second monitor that I use with a HDMI cable still works.

  Here is a screenshot - one screen shows white and I'm typing this on screen 2 (continue below)

  I've updated my drivers in Device Manager but problem persists, here's my profile for screens and link to full

  (continue below photo)

  

  Complete specifications

  http://Speccy.Piriform.com/results/ZRXCgJC8x3PrsszxBodRVhn

  From my understanding the cables of the screen white screens LCD is still, this problem started after the update of Windows 10 so I'm reluctant to think it's that. My laptop is still under warranty but do not want to send in if he didn't need that I need for work.

  I found some information online saying that a restore Image will not work, but I have an and you can try it if need be.

  Other information found online says that my computer basically "forgot" that I have a main display to get out information in and make the screen and that's why my second screen works perfectly and me might be able to solve this problem with the start of the saving mode and try to fix it from there again I've never done this and don't want to cause more problems doing things like that.

  What could be the best way to go forward with this problem is to say. :

  * Is there a way to check the LCD cables without disassembling the computer. (Don't want to do that, and don't think it's the fault)

  * System Restore will help

  * Where / who should I contact for help in this regard

  Thanks for any help provided and please tell me if you need any other info to help. I really want to to fix the problem rather than take it to a guy or HP

  whitescreenUser

  It's a bad screen. The upgrade of Windows 10 timing is a coincidence. You can continue to use it as a desktop computer with an external monitor forever.

• 3rd generation ipod white screen

  I know it's old, but working well... so far.  White screen.  It is recognized by itunes when plugged into the computer.  Restored successfully on the itunes screen, always white.  Tried the fix with holding home and power button.  Tried to hold the House, volume and power.  Screen remains white.

  My question - is all hope gone and I must finally remove this ipod?  It's been great and it's a sudden death - hard to see it go.

  Thanks for any help...

  The 3rd gen iPod "classic" has a great sound.  If you tried to do a restore already, its likely to be a hardware problem, unfortunately.

  These older iPods are easier to repair because they are assembled from items separated and not so integrated and miniaturized.  My work 3rd generation iPod was reassembled broken iPods that I bought on eBay, by swapping pieces.  The screen is not the thing that is broken, most of the time.  If you are somewhat technically inclined, you can remedy.  You can post back for more information.

• iMac 8.1 White Screen of Death

  Before I launch into history, here are some of the relevant features of my computer. I have an iMac 8.1 (2008 model) with a processor clocked at 2.66 DC2, 2 GB of RAM and a hard disk of 1 TB with three partitions. The main (about 640 GB) ran 10.11, the second a (32) snow leopard and the rest it has been implemented with Windows 7. This configuration worked well enough (if a little cludgily) for some time, but the other day, things came to a head.

  It has a bit of history history, please bear with me.

  Monday, after the computer has been awkwardly slow with no application, I thought to reinstall El Capitan to see if that would help. After the installation failed, I ran disk utility on the main partition to see what he would say. After a brief inspection, he said that it was a problem he couldn't solve, recommended making sure that my data has been backed up and clear. The Snow Leopard partition, however, seemed fine. Somewhere along the line I also gave Techtool Pro 8 a spin; It seems to indicate that most of the things associated with non-partition were very well, but found that the hard drive (in general) has failed to test temperature.

  In any case, I boot in Snow Leopard, I guess to see if the old version of disk utility would have a bit more luck (this may sound stupid, but I confess I have a lingering distrust of the latest iteration of this software). As expected, he did not progress. I even ran DiskWarrior 4, and he says that the partition was shot. Somewhere along the way, I had disassembled the main partition for a reason, and after not being able to get him back for some time (and getting only ReadOnly when she didn't come back), I myself resigned and the likelihood that the partition was shot. We ran by Best Buy and picked up a 1 TB external drive (which I never had before, as stupid as it sounds; "I guess I never realized to cheap ways they had obtained). I spend a night using carbon copy to backup my important data and when I'm done moving things on the next day morning, delete this partition. So far so good. I reinstall El Capitan without any hitch and spend a day or two, transfer of information on the 'new '. I also make sure to configure the new disk as a time Machine, get all my data saved on it.

  Things seem to be fine, and I'm starting to get back to my daily routine. However, this morning, after the connection and use it for a little while, the entire screen changes abruptly a very light grey/white color and no unresponsive. I understand that nothing is happening, stop and restart the power. The screen remains white. The slider appears, but nothing big happens else. At some point (I'm afraid I don't remember if it's on this first boot or one of the few later), a folder with a flashing question mark appears (this never appeared, however, on one or two startups). I try different things: reset PRAM (which at least brought the sound chime, who had kept silent, back), reset the SMC and boot into safe mode, a disc hard my choice with the Option key pressed, or since the Snow Leopard DVD. When he answered the optionkey down initially, it would shoot the cursor and screen as if he was going to offer me different drives, but nothing ever came, not even the external drive. After further start attempts, he stopped to show anything, even the cursor.

  I have the external drive disconnected right now. When you start the computer, a white screen comes up and then nothing else seems to happen, no matter what key combos are pressed.

  It was for some time ago, but I thought it would be useful to mention that we sometimes have blackouts here. After such an event, old computer power supply burned and had to be replaced. Since that time, however, everything seemed to work pretty well.

  I looked around, discussions and others to try to see if I could find a similar experience, but as it is I'm quite puzzled. The only thing I have not tried is opened and unplug the hard drive as suggested by an intern, to see if she might try to find other media to boot from.

  I thought I would ask here to see if he has any advice this community had to offer before doing something drastic. Thanks for reading and your review.

  If you have the original install disc provided with the computer, run Apple Hardware Test Mode Extended 2 - 3 times back to back. If errors appear when you have confirmed a significant hardware problem the computer has to go repair. The reason to run AHT in Extended Mode what is complete, but it can miss errors during the first and even the second pass.

  However my guess is have some other hardware problem and you really takes them to a CENTER in your area to be diagnosed professionally.

• WhatsApp works do not last night... When I opened the app, it shows white screen and closed after a certain time.

  WhatsApp works do not last night... When I opened the app, it shows white screen and closed after a certain time.

  Try to do these steps, it should help:

  1 check WhatsApp update: Open App Store from your iPhone, click on updates, check if the application needs to update.

  2. restart your iPhone: hold down the sleep/wake button to it turn off and then turn it on again.

  3. close the app: multitasking opened by double pressing the Home button, slide the nonresponse apps up to close.

  4. go in the settings, press Whatsapp, touch turn off everything except mobile and notofications data.

  5. return to the home screen and open whatsapp.

  6. go in the settings, press Whatsapp and turn back.

  7. open whatsapp again. It should work now.

• When I return to the page of Google search results, need me a white screen of Google

  For example, I click on a link after doing a search on Google, then I decide to go back and check one
  the other links. When I return to the place to see my screen of Google results, I was white
  Screen of Google. So I put my search terms in all over world. This does not happen using
  Internet Explorer. Thanks for any help

  I have the same problem and looked for help on the Mozillazine.org site. Didn't help either, but I found that when you get the blank screen, click REFRESH, get the desired page.

  Another solution for this problem is available here: https://support.mozilla.org/questions/970863?page=2#answer-485663

  "Alternative" added as requested by jscher2000

• Satellite M50 - white screen after login on Win 8.1

  Satellite M50 running 8.1 Win
  After login, download mouse white screen, but nothing else.
  Can run Explorer.exe manually via the the Task Manager for go, but some applications like Acrobat and Windows Mail does not work.

  I searched online and tried all sorts of fixes suggested without result.
  Any suggestions gratefully received!

  I don't know what the problem is here, but you can try to Win8 will stop completely and check the repair options. Try again with the system restore and roll back the OS a few days back. Maybe this will help.

  http://APS2.toshiba-tro.de/KB0/TSB2A03ES0000R01.htm

• Satellite C855 - white screen after BIOS update

  Hello

  I am a beginner user,
  I have Satellite C855
  Yesterday, I downloaded a 'update BIOS"that was sent to my computer.
  Since that my screen is blank, there is a hum in the background.

  I have a recovery back up on my external hard drive, but of course, the screen is blank so I don't know how the product.

  I think I must have downloaded a model or the update was not compatible.

  Hello

  White screen do you mean that nothing appears on the screen?
  You see the start screen of Toshiba, or if you are able to access the BIOS?

  Where this is not possible, try this:
  Disconnect the power adapter, remove the battery.
  Press and hold the power button for about 30 seconds.
  Then connect the two parts (batteries and AC adapter) for the laptop and try to turn on the unit.

  In case this would not solve the problem of the laptop, I'm scared of m the BIOS update was not completed successfully and I think that only authorized Toshiba service provider would be able to help you.

• iMac with new ssd showing nothing but the pointer and white screen

  Hello

  I'm trying to fix an old imac (2008), 20 ", the mac crashed hard drive so I installed an SSD and tried to use the start switch to start on my yosemite bootable installation usb. When I try this, start pressing the option key, rather than see the start selector I see only a white screen with the black pointer. I tried to start another mac to this usb port, and it worked well. No one knows why this happens?

  Thanks in advance,

  Jasper

  You are using a wired keyboard connected directly to the back of the iMac? If this isn't the case, you could try that.

• White screen on Equium P200

  Hi all!
  yesterday morning I started my computer, after 5 min, I close the lid, and I'm going to work.
  When I'm back back I opened the lid and I get a white screen.
  Well, I think is right for the moment. I restarted but white screen again.
  I restarted many times but nothing. I heard the noise of vista hard drive to work, but I don't get nothing on the screen. I'm trying to connect an external monitor but nothing.
  Anyone have this problem? I Don t has an idea of what I can do to recover the normal screen of you.
  If I use reinstall drive I lose all my data and I don't want to. Can someone help me with a few great ideea what can I do?
  Thank you much in advance.

  A white screen usually means that the backlight is on but no signal reaches the graphics card on the screen. This could have many reasons such as:

  -a broken screen cable
  -graphics card failure
  -view controller malfunction
  -some short circuit between the graphics card and the screen

  In your situtaion I use warranty (if still present), sending the machine to the [the closest available service provider | http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_whitepaper.jsp?service=EU&WHITEPAPER_ID=0 000000871] and have them check the hardware on some failures...

  That's all I can tell you from my experience with white screens...

  Welcome them

• Satellite Pro L300 - white screen after login

  Hi, got a laptop off a friend to watch as not start correctly. Vista Edition running Home Premium, it will start up the screen of the user ok but when a user is selected the screen goes white with just the mouse pointer showing (which moves ok on the touchpad). I can press Ctrl Alt Delete and get the blue menu screen - if I try the Task Manager with it it goes back to the white screen.

  I tried a repair of end upward to F8 but said no problems found. I can also start ok in Mode safe without getting a white screen. I tried a high diagnostic of MSConfig startup but still the same. I also disabled all services but still a Virgin.

  I have a secondary partition on the disk with the recovery of HARD drive there, but do not want to reformat. I tried to restore to several different, but restore points remains empty at the normal start screen.
  Someone at - it find it.
  Mark

  Hello

  Its hardware problem or software.
  Start the laptop in safe mode means that some essential software process would be disabled and the system would use only a few basics of essential equipment.

  So even if the laptop runs correctly in safe mode, it could be a hardware problem.

  That's why I think only with the help of HARD drive recovery would be the best way to know what's wrong here...