BIOS Configuration Utility (BCU) for HP Z840 workstation.

Similar Questions

• ProDesk 600 G1 BIOS configuration of the TPM secure through the BIOS Configuration utility

  We have a range of devices, computers HP desktop and laptops in our environment.  Devices are all running Windows 7 64 bit and should have Bitlocker enabled, but we found that some were not encrypted.  So I am trying to set up a remote BIOS and Bitlocker config activate software that we can get out via SCCM and then embed in a task sequence image for new machines.

  I use the Bios HP Configuration utility to check a BIOS password is set and then activate the TPM chip.  I took a BIOS config output of each of our models and created a settings file that has all of the TPM associated parameters of all models.

  At the moment I run Setup BIOS utility manually for testing.  On all models I tried that works very well, except for the 600 ProDesk G1 SFF.

  When I run the utility on the ProDesk 600 G1 MFS, it says that I have managed to update the settings, and when I check the BIOS, the TPM secure has been unhidden and the TPM Management was given to the operating system (two settings I change), but the TPM itself remains hidden.

  It's the release of the BIOS configuration utility (it uses the 2.60.13.1 version, which uses plaintext passwords.  I also tried with the 3.0.13.1 later version that uses password files - same result)

  C:\ > BiosConfigUtility64.exe /cspwd: "password" set: "TPM_Config.REPSET"
  
  < BIOSCONFIG Version = "2.60.13.1" Computername = 'HP600G1' Date = "24/07/2014" Time = "13:01:37 ' UTC '1' = >"
  
  < SETTING changeStatus = "pass" name = "Embedded Security Device" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [hidden device]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [device]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "Enable security on the next boot" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "The BONES of on-board safety management" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SUCCESS msg = "Successfully set BIOS config." / >
  
  < information msg = 'BCU return the value' real '0' = translated = '0' / >
  
  < / BIOSCONFIG >
  
  C:\ >

  And after a reboot (where it should activate the TPM), BIOS shows as disabled built-in safety device (see attachment for the image).

  I have tried everything I can think of to get this to activate, including:

  • Different versions of the BIOS configuration utility
  
  
  • Remove the password from the BIOS and the application in the same order as the parameters
  
  
  • Different passwords
  
  
  • Reboot and allowing the machine to start completely to Windows before checking if the setting took effect

  I also tried to add the utility and the commands for an SCCM package and it works directly and as part of a sequence of tasks to see if that makes a difference, but nothing I've done has activated the TPM module.

  I know that the TPM module works, as you can turn it on manually and then Bitlocker can be applied to the machine, but with thousands of devices in our environment, I need to get this job without the need for manual intervention.

  Has anyone else had this problem and found a solution?  Or has someone at - he managed to activate the TPM on the SFF of 600 ProDesk G1 using the BIOS Setup utility?  Any ideas / suggestions would be very appreciated!

  P.S. This thread was moved from the company PC - Compaq, Elite, Pro for HP PC Client management. -Hp moderator of the Forum

  This problem has now been resolved by HP.
  
  They provided a replacement motherboard for the test machine I was using that solved this problem. I don't know what kind of motherboard failure could prevent the activation via the script TMP chip but not prevent activation through the BIOS menu, but as a replacement solved the problem, then it must be a hardware failure.

• BIOS Configuration utility

  Hello
  I was wondering if Toshiba laptops have a Bios Configuration utility similar to what HP and Dells have. HP has a utility called 'Biosconfigurationutility.exe' which allows the switches to export the configuration file, maniplulate it and import back into the Bios. Dell has a named CCTK aswell.

  The main objective of the present is so that I can import a file of responses in SCCM to set up the laptop to turn on the TPM so that when the generation is here, I can run a windows task to activate Bitlocker with the TPM secure.

  Please help me.

  Thank you

  As far as I know laptop Toshiba don t have something like that. Only the tool where you can change some settings in BIOS is Toshiba HWsetup utility you can find in Toshiba Assist optionally optimize.

• Compaq DV7800: A Bios Configuration is required for the PCIE graphics card

  HII

  I have a small form factor dc 7800 Desktop

  And I also have a Nvidia 8600GT graphics card

  When I mount the graphics card on the computer PCIe slot

  would you like to work in VGA connector and when I use tha Port DVI form map

  Nothing... So I need a Bios Config to work?

  For the factor, I put the motherboard can configure the card

  I have all the equipment, power supply, HARD drive...

  Can you help me?

  Thank you

  This card is perhaps too powerful to 240W power supply that has your PC.

  I would go with a less powerful card like the Radeon HD 6450.

  Also before installing the video card, uninstall you the card integrated Intel graphics and check the driver to uninstall before installing the nvidia card?

  NVIDIA used to list the current of each of their cards, but now when I click on the sheet for the 8600 GT, I get very little info.

  http://www.GeForce.com/hardware/desktop-GPUs/GeForce-8600-GT/specifications

  The PCI x 16 slot in your PC has a certain power of only 25W max draw and I'm sure that the 8600 GT draws more power than that.

• HP Pavilion DV7 BIOS configuration utility - 2010ev:

  Hello

  I would like to ask if I can change the configuration to another utility or open the Advanced tab of the existing utility

  No I don't have InsydeH2O Setup Utility v. 3.5 (Locked - no Advanced tab)

  MOBO is Quanta or HP 3624

  HP Pavilion DV7 - 2010ev

  P/N: VC005EA

  I want to replace my CPU of Intel P8600 Q9100 Intel and Intel told me that the BIOS may not support the new processor.

  Then, it is not incompatible with the Quad Core CPU. I suspect that you have just a bad CPU it. I regularly buy with a higher incidence of disorders than processors, there is no other portable computer components. Sellers say they're working, but a significant percentage are bad on arrival.

• The BIOS utility 600th for linux (or boot back disk)?

  Hello

  I need to completely disable the IrDA and put ttyS0 Serial port (COM1). How?

  Assuming I need to the BIOS Configuration utility, but I found no linux version. Or BACK-version that fits on a floppy 1.44 ".

  ttyS0 was working well until I decided to update the kernel (bad idea!) A good point is that now I am able to monitor the status of the battery but ttyS0 dies which lead to situation that gammu smsd is not more work.

  Any help would be more than welcome!

  BR

  Miha-

  Problem solved. Booted from CD http:/miha.webhop.net/600E_BIOS_Configuration.iso

  and then sequence of commands:

  Disable imodem PS2

  disable the ir PS2

  disable the PS2 Sera

  Sera PS2 address 1 (= ttyS0 COM1)

  enable PS2 serums

  And restart. Now, serial port works again. Detective Conan.

• After installing a new HARD drive, I get a screen "control i to access the configuration utility.

  Help?

  I installed a new HARD drive on my xps 15 because the old drive crashed. Everything works fine and the system boots perfectly. Before entering the Dell splash screen, the screen "control i to access the configuration utility" appears for 5 seconds. After that, the normal boot sequence resumes. Can someone please explain to me why this is happening and what I can do about it?

  Here is a link to the screen I get started: http://s102.photobucket.com/user/alexcinie/media/photo_zpsb75f0a7f.jpg.html

  The mSATA drive is used as a cache for the hard drive dynamic - these are essentially implemented in a RAID 0 array.  See the link below (it is for Alienware, but applies to your system as well).

  If you want to keep the disk cache, you need to configure the array as shown.

  http://www.Dell.com/support/troubleshooting/us/en/04/KCS/kcsarticles/ArticleView?docid=564442

• status of landmark HP + generic host process for the + serious mistake WMI + system configuration utility + ALG pop-up messages

  I have a desktop computer, with Windows XP. He has a very good performance for 4 years. But in recent days, some of the messages appeared, and suddenly, the computer restarts. and if she did ' t restart directly, she performed very bad (gel + slowly). 6 messages appeared, they are:

  1 - generic host process for win32 services has encountered a problem
  2 - problem WMI
  3 - the system has recovered from a serious error
  4 system configuration utility
  Situation 5 - hp cue has encountered a problem
  6-application Layer Gateway service
  Help, please.

  Hi Alaa' Kabbani,.

  1. did you of recent changes made to your computer?

  2. which antivirus app do you use?

  3. What is the brand and model of your computer?

  I suggest to follow the steps below and we update on the State of the question.

  Method 1: Disconnect any new hardware

  If you have recently installed a new hardware device, the necessary driver so that the material can not be installed or the driver may be damaged or incompatible. To determine if this is true, follow these steps:

  1 unplug the appliance.

  2. restart Windows XP.

  If Windows XP starts successfully, there is a driver problem with the new material. Contact the manufacturer of the device for drivers updated to the device or to learn more about known hardware issues, so that you can reinstall the device.

  For information about how to contact the manufacturer of the device, refer to the Microsoft Web site at the following address:

  http://support.Microsoft.com/GP/vendors

  (http://support.microsoft.com/gp/vendors)

  Microsoft provides third-party contact information to help you find technical support. These details may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.

  If this method resolved the issue, you are finished. If this method does not work for you, go to method 3.

  Method 2: Disable automatic reboot in case of system failure

  If the system reboots continuously, do the following:

  1. reboot the computer.

  2. as the computer restarts, press the F8 key repeatedly until you see the Windows Advanced Options screen.

  3. use the arrow keys to select disable automatic system error rebootand press ENTER.

  4. If you receive an error message, follow these steps to search the Microsoft Knowledge Base for useful information about the error message:

  a. copy the text of the error message.

  b. visit the following Microsoft Web site:

  http://support.Microsoft.com

  (http://support.microsoft.com)

  c. type the text of the error message in the Search box, and then type the name of the product you are using, for example "Windows XP".

  d. click on Searchand try to find an article that will help you solve your problem.

  If this method worked, you have resolved the problem of your computer restarts continuously. However, you can continue to troubleshoot driver problems. See the "Symptoms" section again and determine which method to use to solve the problem.

  If this method worked, you are finished. If this method does not work for you, please try Method 3.

  Method 3: Use the known last good Configuration feature

  If you can start the computer successfully, you can use the known last good Configuration feature. This feature uses information that was saved the last time that you shut down the computer before the problems started. This feature allows to restore your registry settings and drivers to the previous information.

  If you are not completely sure what that means, don't worry. None of these reviews will damage your computer. However, you should be aware that if you do this, any changes made to your computer after the date of last known good configuration will be lost.

  If you have recently installed a driver and know a configuration problem, this method will probably work for you. Unfortunately, this feature does not solve the problems caused by missing drivers or corrupt or files.

  To use the last good known Configuration, follow these steps:

  a. restart the computer.

  (b) that the computer restarts, press the F8 key repeatedly until you see the Windows Advanced Options screen.

  c. use the arrow keys to select last good Configuration known (your most recent settings that worked), and then press ENTER.

  d. If you are prompted to select an operating system, use the arrow keys to select the operating system and press ENTER.

  If this method worked, your computer is restored to a good working state. You still have to investigate on what caused this problem. To do this, please see the "Next steps" section for troubleshooting resources more.

  Also refer to this link: Slow PC? Optimize your computer for peak performance

  http://www.Microsoft.com/athome/Setup/optimize.aspx#fBid=G1iW6Kb0x5J

  WARNING CHKDSK:

  Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Anti Virus WARNING: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  If you have trouble following the suggested steps or if the problem persists, please let us know and we are ready to answer them for you.

• Acer Aspire V3 - 772G - BIOS setup utility menus have disappeared

  Acer Aspire V3 - 772G - BIOS setup utility menus have disappeared

  I have install this laptop brand new, pre-installed with Windows 8.1 for my sister-in-law who bought it.  The installation went well BUT the 16 GB USB device I bought such as advised by the literature of Acer to store the recovery partition was not large enough, 14.4 GB physical capacity.  Acer the book says to use a 16 GB or more, so I did.  I naively thought that a USB key which has been marked 16 GB would be appropriate.  Not the case.  I had to buy a bigger but am still waiting for delivery.

  So I decided to any HARD drive to save the work I had done, but found only the Acronis Backup and Recovery DVD would not start the image.  I went into the utility configuration and adjusted the start parameters to inherited and modified device priority.  Acronis wouldn't so I did not continue.  I went back into the configuration utility, use F9 to restore the default value and to my astonishment that the DUAL boot option was now gone and Windows startup option was also gone.

  This means that £800 this laptop is now unusable.  The installer standalone reconfigured without warning.  Nowhere is there at - it advice or advice do not use the Setup utility when it erases the features that cannot be recovered by using F9 to restore the default configuration.  If this isn't a serious design flaw, I don't know what is.

  I am deeply worried because the idea of a BIOS setup utility behave in this way seems so unlikely that I wonder if anyone will believe me.  How are the Setup utility has been designed to self-harm like this?

  Your suggested action works!  Thank you very much.  You saved my life.

  loungehake

• Satellite Pro U400: How to configure the VLAN for the Marvell Yukon LAN control.

  Hi all
  I need to access the 2 VLANS with the controller LAN Marvell Yukon 88E8072 for my Satellite Pro U400. I installed the necessary Configuration utility network Marvell tell me after installation, VIRTUAL local network settings must be mounted in the Device Manager (Windows 7, right click on computer, properties, click device/network management adapters/double on Marvell Yukon 88E8072 PCI-E Gigabit Ethernet Controller), I can't find a thing to configure here but wake-on-LAN.

  Any suggestion? Thank you!

  Michael

  Hello

  I think that in this case, you can use a network switch.

• W520 Bios Update Utility 10 64-bit Windows

  Friends

  Earlier, I had a Thinkpad W520. Looks like a powerful machine. He already started level Win 10 Pro 64 bit.

  Now I tried to update the BIOS on this issue but don't know how to proceed. The current BIOS is:

  BIOS
  LENOVO brand
  Version 8BET55WW (1.35)
  Day 06/12/2011

  So, it is already 5 years old. I tried to find utility to update BIOS for 64 bit Win 10 on the Lenovo support site, but not been able to find one for this model. I find one for 64-bit Windows 8, but not to win 10.

  Can I use the Win 8 BIOS update utility to update my W520 at 1.42 BIOS? Or what are my options?

  Thank you

  Calle

  On machines like yours that were ever sold with pre-installed win10, I suggest burning to a CD and update the BIOS in this way.

• Launch the Configuration Utility 4.9 x

  I'm launching Configuration Utility 4.9 x.  I get the box, select Local computer, click OK and then nothing is displayed.

  In the HP. File Dss.ConfigUtility.CrashDump.log, I see a warning message: Unhandled Exception has occurred in the DSS service.  Message: Failed to create 'serviceconfigurationwindow' failure, defined in Assembly...

  I tried to run it as an administrator as suggested, but nothing helped.  I am looking at different security settings, but can't nail the right pair for the moment.

  Any suggestions would be greatly appreciated.

  Solved by putting the exe file in Windows Server 2003 compatibility mode.

• System Configuration utility

  I had a hotline to change how windows starts and clear my system for viruses etc.

  I have no w received a message on my pc every time you start by saying that the system utility is in diagnostic or selective startup mode.

  I need to choose normal startup on the general tab mode to start windows normally and undo the changes you made by using the system configuration utility. Help!

  Where is THE general tab and that make the changes I need to do when?

  That's why using msconfig to deal with start-up problems is the wrong way to go.

  To answer your specific question, click Start, then click Run, type msconfig in the box "Open", and then click OK.

  Running msconfig starts the System Configuration utility.  It has several tabs, the leftmost is the general tab you're looking for. Click the general tab and then click on the 'Normal Startup' radio button.  And then click OK.

  When you restart, you'll be in normal mode - but probably some problem has prompted "phone support" to run msconfig first place will return.

  If you want to fix things rather than simply hide them with msconfig, please post describing the problem that comes up when you restart in Normal mode.

• Dell Photo AIO Printer 962 does not. Follow the instructions in the configuration utility.

  Driver is there but does not connect. I can print alignment but not test. I tried all the suggestions, I found, but still won't work; even uninstalled and reinstalled with the CD. Follow the instructions in the configuration utility. I saw other people with the same problem. can't the difficulty of mine. It also tells the boot trying to remove the abnormal length. Xc0000005 code exception)

  Hi Ohdiane1057,

  Note: a patch is released for Dell AIO Printer 962 Photo, I suggest visit this community link provided below and try to install the patch and see if the problem is resolved.

  http://en.community.Dell.com/support-forums/peripherals/f/3528/t/19046379.aspx

  Thank you, and in what concerns:
  I. Suuresh Kumar - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  

• Laptop turned on, password appears on black screen, windows loading bar appeared, then got two options in the BIOS Setup Utility and change Boot Device order, I don't know what is happening, help please!

  My sisters notebook froze and she turned off the power switch, when she turned on the screen was black and a password box appeared when I entered the password, the XP loading bar came as usual and then I had two options at the bottom of the screen. We want to press F9 for and the other was to press F10 for BIOS Setup utility, after seconds, the screen went black and then appeared again the password and the circle continues. The laptop is only 1 week and I don't know if it's something she did or if it's a technical foul, I would be grateful if someone could help me or if I should take it to a technician. The laptop is a Compaq Mini 110 and it works on Windows XP Home Edition.

  Hi, your sisters Notebook is under warranty and it could be a hardware problem.

  As the laptop is only one week.

  I suggest that advise you your sister back to the place where it has been sold since.

  Slan go foill, Paul