blocking of websites for users of vpn ipsec offline

Similar Questions

• Downloadable ACLs for users of VPN

  Hello

  I replaced the old pix with ASA (7.2). There were groups configured for the remote VPN users authenticated through the ACS and ACS download a specific ACL for each group to the PIX. After the replacement, users cannot establish the VPN connection. After troubleshooting, I discovered that the downloadable ACLs were not working very well. When I disabled this option the established tunnel. When I get back to the old pix with the same configuration, it works very well with downloadable ACL option. I opened a TAC case and he said the v3.0 ACS (I) are not compatible with the ASA. He did not really convince me and he asked to try to use the option to pair AV. I tried option pair AV with ASA and it did not work also. can you please advice.

  Hello

  Check out this point,

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCef21184

  In addition, 3.0 is very old, and I guess that in this version, we have "Downloadable PIX ACL" and not "downloadable IP ACL", on ASA download able ACL will work but with "Downloadable IP ACL" but not with "Downloadable PIX ACL".

  Kind regards

  Prem

• Routing of traffic for a specific user through vpn Ipsec

  I want to route traffic to a specific host on the internet through our external interface (for example, 7.7.7.0/27) instead of the internet connection of the client (for example 9.9.9.9).

  I have already added 9.9.9.9 in the split dns acl so that the road is inserted on the client workstation and a default route on the external interface is defined as follows:

  CISCOASA # run HS | I have the route outside

  Route outside 0.0.0.0 0.0.0.0 7.7.7.30 1

  Nat config

  object obj-InsideNetworks network

  NAT 7.7.7.3 Dynamics (indoor, outdoor)

  No nat

  NAT (inside, all) source static obj-InsideNetworks obj-InsideNetworks destination DEST-Interior-SHEEP inside-DEST-SHEEP no-proxy-arp static

  object obj-InsideNetworks network

  range 10.0.1.0 10.0.255.255

  object-group network inside-DEST-SHEEP

  network-object 10.0.3.0 255.255.255.0

  object-network 10.0.2.0 255.255.255.0

  object-network 10.10.10.0 255.255.255.0

  object-network 10.0.4.0 255.255.255.128

  The static IP assigned to the vpn client is 10.0.4.150 if it is not the scope of the Interior-DEST-SHEEP.  If again I traceroute

  9.9.9.9 when connected, I get the first bond 7.7.7.1 and it stops there.

  Would appreciate any help on this.

  Hello

  If you try to NAT the VPN user traffic when it connects to the Internet through the ASA NAT configuration so that the user should then be

  network of the VPN-CLIENT-PAT object

  subnet 10.0.4.128 255.255.255.128

  dynamics of NAT (outdoors, outdoor)

  Insert the dynamic PAT public IP in the above configuration. You can either use "interface" parameter to use the public IP address of ASAs or insert a detached public IP address that can be used. I guess the Pool of VPN uses the 10.0.4.128/25 subnet.

  You must also make sure you have the following configuration enabled

  permit same-security-traffic intra-interface

  You can check with

  See the race same-security-traffic

  Note that there is another similar parameter that ends in "inter-interface" who used to work for this situation.

  Hope this helps

  Let me know if make you it work

  -Jouni

• Impossible for users of vpn SSL ping

  I have install several ASA with Anyconnect SSL VPN function, but I have never been able to ping to an IP address that has been assigned to the remote user. I'd be able to ping the remote user? Do I need to configure anything in any political group or the user to activate this?

  Triton

  Triton,

  Absolutely, you will be able to ping the RA client when it connects, if the customer is able to ping your internal resources, but the connection does not work the other way, then most likely the RA client firewall blocking the packets. Most of the software including Windows Firewall Firewall delete unsolicited incoming traffic that does not match a traffic sent in response to a request of the computer (solicited traffic) or unsolicited traffic that has been specified as allowed (except traffic).

  Kind regards.

• Group-lock for users of vpn with acs

  Hello

  Is it possible to controll what VPN profile, a user is allowed to use by Cisco ACS or the router?

  2811 router IOS 12.4 worm, ACS 4.1 using

  I just want to be sure that the VPN allows the user only the Client Profile assigned to them and no other profile groups.

  Example:

  User123abc gets their hands on a profile of co-wokers.

  HR_User_Profile.pcf

  SALES_User_Profile.pcf

  User123abc belongs to the Department of human resources and should be able to authenticate with HR_User_Profile. If User123abc is trying to authenticate by using the access SALES_User_Profile should be rejected.

  Any documentation explaining how to set up?

  The ASA will be your option. This should be controlled by the values of tunnel-group and class-group policy, group-lock, ACS and ASA

• Blocks VIRTUAL local network access to a tunnel VPN IPSec on WRV200?

  I have two identical WRV200 wireless routers which are connected by a VPN IPSec tunnel.  This goes to my LAN LAN of my parents.  Everything works well.

  But I also have my WRV200 configured for two VLANS.  Vlan1 for my network and secure wireless access.  VLAN2 for a WiFi not secure for customers.

  My problem is that my guest on VLAN2 slips through the VPN devices and access on LAN of my parents.  I'm looking for a way to block to do this.

  I use the version of the software on the two routers (v1.0.39).

  For what it's worth, I know that my receive an IP address in the range 192.168.x.101 DHCP - 199.  I could assign a different range if that helps.  I thought that I could block this beach on the remote router firewall, but I see there is blocking a single IP address at the time, maximum of 8.  Am I missing something?

  Or could I put something weird in the routing tables somewhere to get the IPs guest out of lala land?

  Any suggestions are appreciated.  I can't be the only one in this boat.

  Steve

  Try to check local and remote, vpn under safe group settings if you change the ip address range subnet. Don't include the range of ip addresses of the computers wireless comments so that it will not pass through the vpn tunnel. If there is no ip range option, you must to the subnet of the network in order to control the ip address you want to allow on the vpn tunnel.

• Type of certificate for ASA VPN IPSEC

  Hi all

  I'm looking to set up an IPSec VPN connection that will authenticate users by certificate only. I configured everything successfully with the local AAA login, but seeks to convert a signed certificate and generate certificates user for users that are not part of a company or Active Directory.

  So here's my question. What kind of certificate I buy (lets say VeriSign aka Symantec)? And if I want to only use this certificate for my VPN and its customers, can I install it on the Cisco ASA and generate user certificates, or should I set up a Windows Server with CA and create all the certificates on this machine?

  My goal is to install the agent AnyConnect 3.1.x on laptop computer of the user, install the certificate user myself. No webVPN or on behalf of the user. I tried the local certification authority in the ASA in a dev environment, but have had no luck so I thought I'd just signed good immediately.

  Thanks in advance,

  BROKEN

  > Do you think I should have a 3rd party signed certificate

  If the VPN is not only used for internal staff, and then always opt for a public certificate. If you ask other users to install your root certificate, you ask them to allow you to be a man in the Middle for all their traffic. It's nothing that needs to be done.

  Registration is generally just to configure the trustpoint and install the certificate. It is very likely that the certification authority uses an intermediate certification authority, so you should install that also. (even keep the AC have howtos on various platforms).

  > I'm still learning here so I apologize if my questions seem to be amateur.

  And be assured, learning never stop... :-)

• Setup for use with Cisco Anyconnect VPN IPsec

  So, I had trouble setting up VPN on our ASA 5510. I would use IPsec VPN so that we don't have to worry about licensing issues, but what I have read you can do with and always use Cisco Anyconnect. My knowledge on how to set up VPN especially in iOS version 8.4 is limited, so I've been using a combination of command line and ASDM.

  I am finally able to connect from a remote location, but once I log in, nothing else works. What I've read, you can use IPsec for client-to-lan connections. I use a pre-shared for this. Documentation is limited on what should happen after have connected you? Shouldn't be able to local access on the vpn connection computers? I'm trying to implement work. If I have VPN from home, should not be able to access all of the resources at work? According to me, because I used the command-line as ASDM I confused some of the configuration. In addition, I think that some of the default policies are confused me too. So I probably need a lot of help. Here is my current setup with the changed IP address and other things that are not related to deleted VPN.

  NOTE: We are still testing this ASA and is not in production.

  Any help you can give me is greatly appreciated.

  ASA Version 8.4 (2)

  !

  ASA host name

  domain.com domain name

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  the IP 192.168.0.1 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 50.1.1.225 255.255.255.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  No nameif

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  boot system Disk0: / asa842 - k8.bin

  passive FTP mode

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  !

  permit same-security-traffic intra-interface

  !

  network of the NETWORK_OBJ_192.168.0.224_27 object

  subnet 192.168.0.224 255.255.255.224

  !

  object-group service VPN

  ESP service object

  the purpose of the tcp destination eq ssh service

  the purpose of the tcp destination eq https service

  the purpose of the service udp destination eq 443

  the destination eq isakmp udp service object

  !

  allowed IP extended ip access list a whole

  !

  mask 192.168.0.225 - 192.168.0.250 255.255.255.0 IP local pool VPNPool

  no failover

  failover time-out period - 1

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 645.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 non-proxy-arp-search to itinerary

  !

  the object of the LAN network

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 50.1.1.250 1

  Sysopt noproxyarp inside

  Sysopt noproxyarp outdoors

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec ikev2 ipsec-proposal OF

  encryption protocol esp

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 proposal ipsec 3DES

  Esp 3des encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES

  Esp aes encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES192

  Protocol esp encryption aes-192

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 AES256 ipsec-proposal

  Protocol esp encryption aes-256

  Esp integrity sha - 1, md5 Protocol

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = ASA

  Configure CRL

  crypto ca server

  Shutdown

  string encryption ca ASDM_TrustPoint0 certificates

  certificate d2c18c4e

  864886f7 0d06092a c18c4e30 308201f3 3082015c a0030201 d 020204 2 0d 010105

  0500303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  3131 31303036 31393133 31365a 17 323131 30303331 39313331 0d 170d 6f6d301e

  365a303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  6f6d3081 9f300d06 092 has 8648 86f70d01 01010500 03818d b 30818902-00-818100-2

  8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b

  37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c

  234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c 51782

  3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02

  03010001 300 d 0609 2a 864886 f70d0101 05050003 8181009d d2d4228d 381112a 1

  cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc

  18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6

  beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef

  af72e31f a1c4a892 d0acc618 888b53d1 9b 888669 70e398

  quit smoking

  IKEv2 crypto policy 1

  aes-256 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 10

  aes-192 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 20

  aes encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 30

  3des encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 40

  the Encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  Crypto ikev2 activate out of service the customer port 443

  Crypto ikev2 access remote trustpoint ASDM_TrustPoint0

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 10

  Console timeout 0

  management-access inside

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2

  AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3

  profiles of AnyConnect VPN disk0: / devpn.xml

  AnyConnect enable

  tunnel-group-list activate

  internal VPN group policy

  attributes of VPN group policy

  value of server WINS 50.1.1.17 50.1.1.18

  value of 50.1.1.17 DNS server 50.1.1.18

  Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client

  digitalextremes.com value by default-field

  WebVPN

  value of AnyConnect VPN type user profiles

  always-on-vpn-profile setting

  privilege of xxxxxxxxx encrypted password username administrator 15

  VPN1 xxxxxxxxx encrypted password username

  VPN Tunnel-group type remote access

  General-attributes of VPN Tunnel-group

  address (inside) VPNPool pool

  address pool VPNPool

  LOCAL authority-server-group

  Group Policy - by default-VPN

  VPN Tunnel-group webvpn-attributes

  enable VPN group-alias

  Group-tunnel VPN ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  class-map ips

  corresponds to the IP access list

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  inspect the http

  class ips

  IPS inline help

  class class by default

  Statistical accounting of user

  I would recommend buy AnyConnect Essentials. The cost of the license is nominal - list of US $150 for the 5510. (piece number L-ASA-AC-E-5510 =)

  Meawwhile you can use the Cisco VPN client inherited with IKEv1 IPSec remote access VPN using profiles *.pcf.

  I believe you can also use the client Anyconnect client SSL or DTLS transport access remotely (non-IPsec) without having to buy the license Anyconnect Essentials for your ASA focus.

  As an aside, note that if you want to use AnyConnect Mobile (e.g. for iPhone, iPad, Android, Blackberry etc.clients) you will also get the additional license for it (L-ASA-AC-M-5510 =, also price US $150)

• For users remote if RADIUS or ldap services available VPN servers are not there?

  Dear people,

  I have ASA Adaptive Security Appliance 5510 with below features.

  Now, what is the best way to setup VPN for remote users to securely, if I have no services LDAP or Radius server.

  HOFW # sh flash:

  path-# - length - time -.

  181 14137344 March 3, 2003 08:36 asa804 - k8.bin

  195 436 sep 2012 01 16:28:05 bar.emf

  75 4096 November 10, 2011 18:41:26 login

  192 1335 November 10, 2011 18:41:26 log/recovery-event.388.20111110.131127

  79 4096 19 January 2009 16:12:34 crypto_archive

  182 7562988 19 January 2009 16:14:06 asdm - 613.bin

  184 4863904 19 January 2009 16:15:44 securedesktop_asa_3_3_0_129.pkg.zip

  185 4096 19 January 2009 16:15:46 sdesktop

  194 1462 19 January 2009 16:15:46 sdesktop/data.xml

  186 2153936 19 January 2009 16:15:46 anyconnect-victory - 2.2.0133 - k9.pkg

  187 3446540 19 January 2009 16:15:48 anyconnect-macosx-powerpc - 2.2.0133 - k9.p

  kg

  188 3412549 19 January 2009 16:15:50 anyconnect-macosx-i386 - 2.2.0133 - k9.pkg

  189 3756345 19 January 2009 16:15:52 anyconnect-linux - 2.2.0133 - k9.pkg HOFW # sh flash:
  path-# - length - time -.
  181 14137344 March 3, 2003 08:36 asa804 - k8.bin
  195 436 sep 2012 01 16:28:05 bar.emf
  75 4096 November 10, 2011 18:41:26 login
  192 1335 November 10, 2011 18:41:26 log/recovery-event.388.20111110.131127
  79 4096 19 January 2009 16:12:34 crypto_archive
  182 7562988 19 January 2009 16:14:06 asdm - 613.bin
  184 4863904 19 January 2009 16:15:44 securedesktop_asa_3_3_0_129.pkg.zip
  185 4096 19 January 2009 16:15:46 sdesktop
  194 1462 19 January 2009 16:15:46 sdesktop/data.xml
  186 2153936 19 January 2009 16:15:46 anyconnect-victory - 2.2.0133 - k9.pkg
  187 3446540 19 January 2009 16:15:48 anyconnect-macosx-powerpc - 2.2.0133 - k9.p
  kg
  188 3412549 19 January 2009 16:15:50 anyconnect-macosx-i386 - 2.2.0133 - k9.pkg
  189 3756345 19 January 2009 16:15:52 anyconnect-linux - 2.2.0133 - k9.pkg

  Concerning
  Vesta
  "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

  With the ASA you will be somewhat limited in what you can do for remote-access-VPN.

  There are two ways to set that up:

  (1) using the SSL - VPN with the AnyConnect Client

  To do this, you must license Premium AnyConnect quite expensive for the amount of competitor users you plan to accept or AnyConnect Essentials cheap license which will give you 250 AnyConnect users which is the platform limit.

  But for the essential AnyConnect license, you need upgrade your ASA RAM because you need an ASA - latest operating system for it.

  But going this path will be the best option.

  (2) with the IPSec Client inherited (EasyVPN). The customer is EOL/EOS announced and not all development will get more. But for now, it could be a way to go until you upgrade your ASA.

  Here is an example of how to configure your ASA for the old CLient IPSec:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a008060f25c.shtml

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• How can I block access to some programs for user accounts?

  I try to block the user sub-accounts to use anything but a handful of programs under professional XP for my boss and have no idea how to go about on this subject in XP.  Any help would be great.

  For each file that you want to block, go to the 'Security' tab and deny execute access for user accounts appropriate .exe files.

  "How to set, view, change, or remove special permissions for files and folders in Windows XP"
    <>http://support.Microsoft.com/kb/308419 >

  HTH,
  JW

• How to use ACS 5.2 to create a static ip address user for remote access VPN

  Hi all

  I have the problem. Please help me.

  Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.

  I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:

  1Ajouter step to attribute a static IP address to the user attribute dictionary internal:

  Step 2select System Administration > Configuration > dictionaries > identity > internal users.

  Step 3click create.

  Static IP attribute by step 4Ajouter.

  5selectionnez users and identity of the stage stores > internal identity stores > users.

  6Click step create.

  Step 7Edit static IP attribute of the user.

  I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.

  so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.

  Wait for you answer, no question right or not, please answer, thank you.

  There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached

• Cisco's VPN IPSec client for LAN connectivity

  I've looked through further discussions and were not able to find a clear answer on this, so I apologize if this is a duplicate question.

  I have the client setup Cisco VPN on an ASA 5505 with tunneling split. I can connect to the VPN very well. I can access the internet fine. I can't get the LAN, however. I try to do a ping, telnet, rdp, etc devices on the side LAN of the firewall without a bit of luck. I have torn down and configure the VPN several times via the CLI and I even used various configurations by using the wizard, all this without a bit of luck. Any help would be appreciated.

  ASA Version 8.2 (2)

  !

  hostname spp-provo-001-fwl-001

  domain servpro.local

  activate the F7n9M1BQr1HPy/zu encrypted password

  F7n9M1BQr1HPy/zu encrypted passwd

  no names

  name 10.0.0.11 Exch-Srv

  name 10.0.0.12 DRAC

  name 10.0.0.10 DVR

  !

  interface Vlan1

  nameif inside

  security-level 100

  the IP 10.0.0.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  ServPro PPPoE client vpdn group

  IP address pppoe setroute

  !

  interface Vlan12

  nameif Guest_Wireless

  security-level 90

  IP 10.10.0.1 address 255.255.255.0

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  switchport access vlan 12

  !

  exec banner * only authorized access *.

  exec banner * this system is the property of ServPro. Unplug IMMEDIATELY that you are not an authorized user. *

  connection of the banner * only authorized access *.

  connection of the banner * this system is the property of ServPro. Unplug IMMEDIATELY that you are not an authorized user. *

  banner asdm * only authorized access *.

  banner asdm * this system is the property of ServPro. Unplug IMMEDIATELY that you are not an authorized user. *

  boot system Disk0: / asa822 - k8.bin

  passive FTP mode

  clock timezone STD - 7

  clock to summer time recurring MDT

  DNS lookup field inside

  DNS server-group DefaultDNS

  10.0.0.11 server name

  Name-Server 8.8.8.8

  domain servpro.local

  DRACServices tcp service object-group

  EQ port 5900 object

  EQ object of the https port

  EQ object Port 5901

  object-group service Exch-SrvServices tcp

  EQ port 587 object

  port-object eq 993

  port-object eq www

  EQ object of the https port

  port-object eq imap4

  EQ Port pop3 object

  EQ smtp port object

  SBS1Services tcp service object-group

  EQ port 3389 object

  port-object eq www

  EQ object of the https port

  EQ smtp port object

  outside_access_in list extended access permit tcp any host *. *. *. * object-group SrvServices Exch

  outside_access_in list permits all icmp access *. *. *. * 255.255.255.248

  capture a whole list of access allowed icmp

  Servpro_splitTunnelAcl list standard access allowed 10.0.0.0 255.255.255.0

  inside_nat0_outbound to access ip 10.0.0.0 scope list allow 255.255.255.0 172.16.10.0 255.255.255.240

  inside_nat0_outbound list of allowed ip extended access any 172.16.10.0 255.255.255.240

  guest_wireless_in list extended access permitted tcp a whole

  guest_wireless_in of access allowed any ip an extended list

  NO_NAT to access ip 10.0.0.0 scope list allow 255.255.255.0 10.10.0.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 Guest_Wireless

  mask 172.16.10.1 - 172.16.10.14 255.255.255.240 IP local pool ServProDHCPVPN

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 625.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT-control

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  NAT (Guest_Wireless) 1 0.0.0.0 0.0.0.0

  static (inside, outside) *. *. *. * 10.0.0.11 netmask 255.255.255.255

  Access-group outside_access_in in interface outside

  Access-group guest_wireless_in in the Guest_Wireless interface

  Route outside 0.0.0.0 0.0.0.0 *. *. *. * 2 track 2

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-server Exch-Srv Protocol nt

  AAA-server Exch-Srv (inside) host 10.0.0.11

  Timeout 5

  auth-NT-PDC SRV EXCH

  the ssh LOCAL console AAA authentication

  AAA authentication LOCAL telnet console

  AAA authentication http LOCAL console

  LOCAL AAA authentication serial console

  Enable http server

  http server idle-timeout 10

  http 10.0.0.0 255.255.255.0 inside

  http 0.0.0.0 0.0.0.0 outdoors

  redirect http outside 80

  redirect http inside 80

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  monitor SLA 124

  type echo protocol ipIcmpEcho 4.2.2.2 outside interface

  NUM-package of 3

  frequency 10

  Annex monitor SLA 124 life never start-time now

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = cisco.spprovo.com

  ServPro key pair

  Configure CRL

  string encryption ca ASDM_TrustPoint0 certificates

  certificate f642be4b

  308202fc 308201e4 a0030201 020204f6 42be4b30 0d06092a 864886f7 0d 010105

  311a 3018 05003040 06035504 03131163 6973636f 2e737070 726f766f 2e636f6d

  31223020 06092 has 86 01090216 13636973 636f2e73 726f2e6c 65727670 4886f70d

  6f63616c 31303034 30383230 35363232 30303430 35323035 5a170d32 301e170d

  3632325a 3040311a 30180603 55040313 and 11636973 636f2e73 7070726f 766f2e63

  6f6d3122 30200609 2a 864886 f70d0109 02161363 6973636f 2e736572 7670726f

  2e6c6f63 616c 3082 0122300d 06092 has 86 01010105 00038201 0f003082 4886f70d

  010a 0282 010100 has 5 b4646cde f981f048 efa54c8a 4ba4f51c 25471e01 459ea905

  313ef490 72b4d853 4e95ab7d a8c1350e 5728dca6 a98c439e 2c12d219 06ee7209

  9f2584d1 b2abf71c 31c0890f 3098533b 6bc3ad4b 3bcd8986 e70ca78e 07a749d6

  ee4e0892 4fcb79b6 724f7012 9f42fc2f b80c17ed adb5d36b 67590061 453d9ae6

  16583d 36 5a22b7c2 737fd705 94656f3f 578fb67f 79bd2a59 17522be3 d2386e22

  2c62352f cda317b0 be805a04 76f19989 34031cbd a5fc62a7 1d9f52f3 00cf60b6

  bbbdc4f0 fb651b82 b3e22a0a 718ff0b4 e213f4ac cdeb413b 9c4a47c3 9134d7a9

  e8dcf2c5 c1cd4075 61d75e3a 475a17f1 2f955741 9ed2a8d6 c381eba3 247134e1

  b5c33fac 7ae03d02 03010001 300 d 0609 2a 864886 05050003 82010100 f70d0101

  156 5fde62c5 b4cbb0f4 0c61fab7 fae04399 27457ab7 9790c 3fac914d 70595db9

  e69d3f19 3476dc51 32c885de b5904030 05624fe0 e8983e0a ab5527f3 8c5dd64a

  1e1a6082 b6091657 8704c 539 a3c6be47 da2a871f 4fafe668 70db2c2b 573d47b2

  7f3df02f c9d53a92 bcf5f518 9953e14c f957a6ca 279f9e9f ddbd2561 6e0503c2

  ba59a165 055d697f dd028d00 5cc288c4 83ced827 9c82ef3e 7e67f2d2 6de573e3

  42a0b6bf ef8d06ed cb9805f2 c38011d3 5263bc3f 5b68df7a bef36c40 8c5e33f3

  26b02c27 63a9848c 8461738f cd19ae95 f059ee34 afe4bdbc 8d8d2335 751b 0621

  65464b2c 4649779d 3ba01b69 8977 has 790 73815f8b 3c483f93 a5ca9685 04b6e18a

  quit smoking

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  No encryption isakmp nat-traversal

  !

  Track 2 rtr 124 accessibility

  Telnet 10.0.0.0 255.255.255.0 inside

  Telnet timeout 10

  SSH 10.0.0.0 255.255.255.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 10

  SSH version 2

  Console timeout 10

  VPDN group ServPro request dialout pppoe

  VPDN group ServPro localname *

  VPDN group ServPro ppp authentication pap

  password username * VPDN * local store

  dhcpd outside auto_config

  !

  dhcpd address 10.10.0.100 - 10.10.0.227 Guest_Wireless

  dhcpd dns 8.8.8.8 4.2.2.2 interface Guest_Wireless

  enable Guest_Wireless dhcpd

  !

  a basic threat threat detection

  threat detection statistics

  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200

  NTP server 38.117.195.101 source outdoors

  NTP server 72.18.205.157 prefer external source

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  SVC disk0:/anyconnect-win-2.3.0254-k9.pkg 1 image

  enable SVC

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  Servpro internal group policy

  Group Policy attributes Servpro

  Server DNS 10.0.0.11 value

  Protocol-tunnel-VPN IPSec svc webvpn

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list Servpro_splitTunnelAcl

  SERVPRO.local value by default-field

  servpro encrypted NtdaWcySmet6H6T0 privilege 15 password username

  servpro username attributes

  type of service admin

  username, encrypted bHGJDrPmHaAZY/78 Integratechs password

  tunnel-group Servpro type remote access

  attributes global-tunnel-group Servpro

  address pool ServProDHCPVPN

  authentication-server-group LOCAL Exch-Srv

  strategy-group-by default Servpro

  tunnel-group Servpro webvpn-attributes

  enable ServPro group-alias

  IPSec-attributes tunnel-group Servpro

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:52bca254012b1b05cca7dfaa30d1c42a

  : end

  Most likely you are behind a router PAT when you are connected to the VPN, so please allow the following:

  Crypto isakmp nat-traversal 30

• need help with VPN IPSEC with RV042

  https://supportforums.Cisco.com/docs/doc-30883

  I enjoy any support for a trial with RV042 VPN IPSec game please.

  Thanks in advance.

  Hi Bay, if you use a Windows computer, you can use QuickVPN. The only thing to note is the router that you have as the gateway to the RV042. You must define a port forward for all IPsec services be able to overcome the problems with the NAT device.

  RV042 configuration is easy, create a name of user and password and that's it. The problem/challenge will get your NAT connection to allow VPN pass.

  -Tom
  Please mark replied messages useful

• Cisco's VPN IPSec help please

  Hi all

  I have 3 sites, the main site has a cisco firewall mikrotik router.

  There is a vpn ipsec existing between the cisco router and another router cisco on the site of the 2nd and it works well.

  Now, I've added an another vpn between a 3rd site and main site. The router on the 3rd site is a mikrotik firewall.

  I had the vpn on the main site and the 3rd site where the mikrotik firewall is and it worked well.

  then for some reason, the vpn with the 3rd site has failed and I could not get it working again.

  When looking for answers, I see that the vpn for the 3rd site States the following:

  #pkts program: 46, #pkts encrypt: 46, #pkts digest: 46
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0

  It seems that no traffic is coming back to the cisco

  I also found the following output below to diagnose the problem.

  It seems that there is communication, but if I read this right, it looks like the cisco established a new number but the other end is not the new number

  new node-1868419487

  node-1868419487 error suppression FALSE "Information (in) condition 1" pattern

  Any help would be appreciated.

  * 02:49:51.911 Jul 22: ISAKMP: (2060): purge the node-1140469772

  * 02:49:59.723 Jul 22: ISAKMP: DPD received message KMI.

  * 02:49:59.723 Jul 22: ISAKMP: node set 1053074288 to QM_IDLE

  * 02:49:59.723 Jul 22: ISAKMP: (2060): Protocol for sending INFORMER DPD/R_U_THERE 1

  SPI 2273844328, message ID = 1053074288

  * 02:49:59.723 Jul 22: ISAKMP: (2060): seq. no 0x645EC368

  * 02:49:59.723 Jul 22: ISAKMP: (2060): my_port of x.x.x.127 package sending 5

  peer_port 00 500 (R) QM_IDLE

  * 02:49:59.723 Jul 22: ISAKMP: (2060): sending a packet IPv4 IKE.

  * 02:49:59.723 Jul 22: ISAKMP: (2060): purge the node 1053074288

  * 02:49:59.767 Jul 22: ISAKMP (2060): packet received dport x.x.x.127

  500 sport Global 500 (R) QM_IDLE

  * 02:49:59.767 Jul 22: ISAKMP: node set-1868419487 to QM_IDLE

  * 02:49:59.771 Jul 22: ISAKMP: (2060): HASH payload processing. Message ID = 24265

  47809

  * 02:49:59.771 Jul 22: ISAKMP: (2060): treatment of the NOTIFY DPD/R_U_THERE_ACK protoco

  l 1

  0, message ID SPI = 2426547809, a = 0x8705F854

  * 02:49:59.771 Jul 22: ISAKMP: (2060): DPO/R_U_THERE_ACK received from the peer 125,23

  6.211.127, sequence 0x645EC368

  * 02:49:59.771 Jul 22: ISAKMP: (2060): node-1868419487 FALSE reason for deletion error

  "Information (in) condition 1"

  * 02:49:59.771 Jul 22: ISAKMP: (2060): entry = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY

  * 02:49:59.771 Jul 22: ISAKMP: (2060): former State = new State IKE_P1_COMPLETE = IKE

  _P1_COMPLETE

  * 02:50:01.111 Jul 22: ISAKMP: (2060): purge the node-1201068805

  Comparing encrypt of 46 to 47436 counters, it seems that router is ecncrypting the traffic, but we do not get any interesting traffic on the remote side.

  Most likely, you might want to check on the remote site, if you see counters increment in parallel decryption and encryption of the counters are incrementing or not.

  On the router IOS, if are incrementing counters encrypt, and confirm that you have not any tunnel existing before the router can be seen same proxy IDs, which is already negotiated with other peer.

  Finally, please make sure that the ESP, 50 protocol traffic is not blocked in transit.
  I hope this helps.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Configuration of the client VPN IPSEC IOS question

  Hello all, I just can't get my IOS Firewall to accept a client based vpn IPSEC connection. The Cisco client comes to expiration and Im never disputed a username and password. I checked my group and a pre-shared on the client and the router. I put my relevant config below. Any help would be greatly appreciated.

  version 12.4

  boot system flash: uc500-advipservicesk9 - mz.124 - 24.T.bin

  AAA new-model

  !

  !

  AAA authentication login default local

  radius of group AAA authentication login userauthen

  AAA authorization exec default local

  radius of group AAA authorization network groupauthor

  inspect the IP tcp outgoing name

  inspect the IP udp outgoing name

  inspect the name icmp outgoing IP

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer isakmp crypto SMOVPN

  key xxxxx

  DNS 192.168.10.2

  business.local field

  pool vpnpool

  ACL 108

  Crypto isakmp VPNclient profile

  match of group identity SMOVPN

  client authentication list default

  Default ISAKMP authorization list

  client configuration address respond

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  Define VPNclient isakmp-profile

  market arriere-route

  !

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  interface FastEthernet0/0

  IP 11.11.11.10 255.255.255.252

  IP access-group outside_in in

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  NAT outside IP

  inspect the outgoing IP outside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  clientmap card crypto

  IP local pool vpnpool 192.168.109.1 192.168.109.254

  IP nat inside source list 1 interface FastEthernet0/0 overload

  outside_in extended IP access list

  permit tcp object-group Yes_SMTP host 11.11.11.10 eq smtp

  allow any host 74.143.215.138 esp

  allow any host 74.143.215.138 eq isakmp udp

  allow any host 74.143.215.138 eq non500-isakmp udp

  allow any host 74.143.215.138 ahp

  allow accord any host 74.143.215.138

  access-list 1 permit 192.168.10.0 0.0.0.255

  access-list 1 permit 10.1.1.0 0.0.0.255

  access-list 108 allow ip 192.168.109.0 0.0.0.255 192.168.10.0 0.0.0.255

  access-list 108 allow ip 192.168.109.0 0.0.0.255 10.1.1.0 0.0.0.255

  access-list 108 allow ip 192.168.109.0 0.0.0.255 10.1.10.0 0.0.0.255

  Here are a few suggestions:

  change this:

  radius of group AAA authorization network groupauthor

  for this

  AAA authorization groupauthor LAN

  (unless you use the group permission for your radius server you need local)

  Choose either on ISAKMP profiles and if you decide to go with and then get rid of these lines:

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  AND change the following items on your profile isakmp:

  Crypto isakmp VPNclient profile

  ISAKMP authorization list groupauthor

  Also if you'll use a list for user authentication, I advise you to avoid using the default list so go ahead and change it too much under the isakmp profile

  client authentication list userauthen.

  If you do not use isakmp profiles change the following:

  No crypto isakmp VPNclient profile

  Crypto-map dynamic dynmap 10

  No VPNclient set isakmp-profile