bug: 'drive not ready' which was already fixed bug is back

Similar Questions

• drive not ready _ stopped system

  I have an Intel computer with windows xp pro, ver.2002, service pack 3. When I try to bring it to the top, the screen reads Media test failure, check cable. Exit Intel PXE ROM, don't drive not ready-system stopped. What has caused this? & How can I fix? I'm not for wise on computers but eager to learn, any suggestions? Furthermore, the cables are connected good.

  "merlin21" wrote in message News: de7da812-de4e-4ace-bbdb-6605739d589f...

  I have an Intel computer with windows xp pro, ver.2002, service pack 3... When I try to bring it to the top, the screen reads Media test failure, check cable. Exit Intel PXE ROM, don't drive not ready-system stopped. What has caused this? & How can I fix? I'm not for wise on computers but eager to learn, any suggestions? Furthermore, the cables are connected good.

  Ensure that there is no floppy disk in the floppy drive if equipped and no CD/DVD in the CD/DVD drive but it looks like a hard drive failure.
   
  When you turn on the computer you hear the spin drive upward? (remove the cover from the computer, but do not touch anything inside).  If it is not rotating until power off (hold power button down until it stops.)
   
  Pull out the power cord from the computer, touch the metal casing of the computer and (assuming a type IDE disk) can detach and reattach the power cord 4 son to drive.  Also carefully Disconnect the Ribbon data cable and attach again carefully.  Make sure that the Ribbon on the motherboard connector is also firmly committed.
   
  Connect the computer again and the power up.  Drive spinning up to now?  Lol bad disc.  Hope you have a backup.  Turning to the top but still the same message?  Hope you have a backup.  Take the computer with all the disks for computers and a reputable Studio programs (big box stores are not trustworthy) repair and hope that they can get down your data and rebuild the machine.

• relocation of cs5 or cs3 both have been upgraded to d/l engraved on asked to insert the cs3 and drive 5 but he was already in the drive I installed to win 10. CS5 has already been installed and turn off before the attempt to re - install. I then tried my

  My computer crashed and I tried to reinstall cs5 or cs3, both have been upgraded to d/l engraved on asked to insert the cs3 and drive 5, but he was already in the drive I installed to win 10. CS5 has already been installed and turn off before the attempt to re - install. I then tried my copy of CS3 same results. Then I tried CS2 it installs and works, but cannot activate online and the phone activation is no longer available it tells me to check the forums?

  First of all, that the software is old enough so that it does not at all with Windows 10... but

  An idea that MAY work to install or run some programs in Windows old 10

  -http://www.tenforums.com/tutorials/15523-compatibility-mode-settings-apps-change-windows-1 0 - a.html

  CS2 (or earlier version) software activation server replacement

  NOTE that CS2 will not install on a Mac "modern."

  l http://helpx.adobe.com/x-productkb/Policy-Pricing/Creative-Suite-2-activation-end-Life.htm

• Drive not ready. Have you ever seen this happen before?

  I'm new to vmware and I have installled just vmware tools for I can have a full screen. Now whenever I'm starting my Ubuntu VM (my only), I get this message:

  "Tvmware - vmx.exe - drive not ready".

  The drive is not ready for use; its doors can be opened. Please check the A: drive and make sure that a disk is inserted and that the door is closed. »

  I can click on Cancel, Try Again or continue. Each option takes me to the same place, namely my Ubuntu vm... It is not cause real problems I know. It is more an annoyance.

  So has anyone seen that happen before or know how to fix? Thanks in advance!

  Welcome to the community,

  Take a look at the virtual machine settings and disconnect the virtual disk. If this does not resolve the problem, please provide the latest vmware.log file of the virtual machine file. Maybe this can help.

  André

• How to sign a document which was already made by other people?

  How to sign a document which was already made by other people?

  Hi grahamdoyle ,

  You must be part of the transaction to sign the document.

  Please use the concept of 'several parties must sign the document' send agreements and collecting signatures.

  See also this KB doc as sequential signature will come into play: the mode sequential and parallel to sending workflow Adobe sign

  You need to add your email address after entering the email address of signatories in the field on the page 'send '.  Also add a signature on the document field & assign it to yourself before sending the document for Signature.

  Once you do this, document will first go the first signatory & sign is the document it will be the second signatory is to you for Signature. When you signed the document, transaction ends.

  Kind regards
  Nicos

• drive not ready message "the drive is not ready for use check the a drive, etc.".

  as soon as I connect my camera to transfer the photo I get following message

  The drive is not ready for use: the door can be opened. Please check the a drive; and make sure that a disk is inserted and that the door is closed.

  I can't get rid of this meaasge if I have to cancel it reappears 10 seconds later it just won't close very boring

  Hello

  What is the number and the model of the computer?

  You have the computer floppy drive?

  Were there any changes made on the computer before the show?

  Follow the steps:

  Method 1:

  Remove all external devices connected to the computer such as printers, scanners and external USB hard drive and check if the problem persists.

  Method 2:

  Check the BIOS setting and also, I suggest you to update the BIOS. To update the BIOS, contact the manufacturer or the manufacturer of the access Web site.

  Note: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• Windows drive not ready

  plurarite of windows disc is not ready

  Hi Superolga18,

  ·         You did it of any material changes or software on the computer before this problem?

  ·         Exactly when you receive the error message?

  You try to run chkdsk on the computer and see if the problem still occurs.

  How to perform disk error checking in Windows XP

  Hope the helps of information.

  Please post back and we do know.

• When I copy to the disc, I get the following error message: Windows – drive not ready

  Below it this box is a red emblem with a X white.  The message is: Exception Processing Message c00000a3 parameters 75b6bf7c 4 75b6bf7c 756bf7c and option buttons here's this message: Cancel try again continue no matter which option I choose, the box disappears for a few seconds and comes back with the sound "attention".  I am usually able to to copy, but sometimes the file will freeze when I try to use the data.  I can't close the message box.  Anyone know what is the problem and how can I fix?

  Hi tbenton1946,

  What application you use to burn the data?

  What is the service pack installed on your computer?

  1. you can access the link below and run the automated Troubleshooter to fix the CD and DVD, read and write the questions and check if it helps.

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  2. try the steps from the link below: how to troubleshoot problems that occur when you copy data on a CD - R or CD - RW optical disc in Windows XP:http://support.microsoft.com/kb/324129

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Bluetoothis is not ready - Qosmio F750

  Hi all

  I only notice this problem recently with my Toshiba Qosmio laptop, in the past I was able to connect to my bluetooth very well (I use it to connect the controllers like a Wii remote). I left it for about a month or two without using it and the other day I went to use and got the error code "Bluetooth is not ready."

  I tried a lot of troubleshooting methods found on this site but I seem to be having much luck restore my bluetooth, so I thought that I ask here before I wreck something on my laptop.

  I have a:
  PC laptop Toshiba Qosmio F750
  Laptop
  Note: 5.9
  processor Intel® Core i7-2670QM CPU @ 2.20 GHz
  RAM: 8.00 GB
  System type: 64-bit operating system

  I have windows 7 and which was already installed on the computer when I bought it under a year previously. I also have an Atheros AR5B195 Bluetooth device, or so it is said in my laptop on a label. Here are some screenshots of my question, the first screen shot in a compilation of photos:

  http://i234.Photobucket.com/albums/ee262/jrich144/Untitled-6.PNG

  Squares:
  Red - me trying to connect a device and or remove a device but get "bluetooth is not ready" message
  Blue - trying in-between bluetooth support
  Yellow - option Bluetooth, bluetooth is turned on
  Green - Log viewer for BTHUSB, event ID 17

  http://i234.Photobucket.com/albums/ee262/jrich144/Untitled2-1.PNG

  Photo, Bluetooth RFBUS Device Manager (this device cannot start (code 10)).

  I tried to reinstall the bluetooth stack and the filters one or twice (not sure if they were good) I also tried a Microsft Quickfix, which ends up being not not compatiable with my system. Whenever I tried a new method I backed up my computer with a restore point system and if the method failed I reloaded my system restore to be if all point right back to square one.

  I would appreciate all help and if I need details more information please let me know. Thanks for your time.

  Hello

  Just at the beginning, I would like to know if you have enabled the BT ON using the FN + F8 key.

  I see the message: bluetooth is not ready
  So I guess it has not been selected by FN + F8

• Hard drive not detected once, but now?

  Hello

  I am Zak, a bit of techno when it comes to playing with the software, or re-Assembly of computers and whatnot. Unfortunately, I have no idea about other things.

  Some quick history on my laptop: the fan was made terrible noises in recent weeks. Initially, I thought it was little dust, so I got a few duster. A lot of dust came out, so that can only be good, but the noise came back after a few days. After some research, I thought that the other logical explanation was probably the hard drive goes bad. I hesitate to send back to HP because I use it for all my college work and it would really put me back weeks to have it not.

  So, a few days ago I booted my computer laptop at a "drive not detected" - or very similar - message. There were a few options for f1 - f4, they were information system and 3 different tests (I think). I ran the tests, all of them came back fine, noting that there are no operating system installed, or a hard drive to boot from. I rebooted because I didn't quite start and wanted to see if there were other options. It turns out that he has started well. I restarted once more and again once it did it very well.

  Then, I coded around, back up all my data, gather warranty information, installation of the HP Support Assistant, etc. I ran all the tests help Wizard and there is no problems found. Since I just got the laptop hibernation when I stop using it, and I have not met any unusual problems. All this sounds great, but my warranty expires December 7 this year. It is safe for me to assume that the "drive not detected" error was just one missed? I read a lot of discussions and FAQS on him and it's not something that happens once and goes. However, I never had to use a warranty so not sure quite how the process works, and as I said, he sent everywhere would put me in my work.

  In order to be a full post, I have a HP G62 - 367DX laptop, running on Windows 7 64-bit OS, and as far as I know there no change was made between error and my prior boot. If there is any other information I can give you, let me know.

  See you soon, thank you for all help and good day

  The wizard tests are not as comprehensive or reliable as the drive hard test in the BIOS... tap F10 as you power up, go and find the hard drive test. Run the long form test and see what it says. It is not uncommon that the hard drive start as intermittent and get progressively more frequent problems. If your drive passes the test of long form, only enough safely, you can assume that it was a unique gremlin, but it's still a really good idea to back up. I like the idea of online backup services and I will quote Carbonite only because it is well known and not as an endorsement. There are several more and year external drive is a good idea.

  You can't put off forever; restarting You'll have to deal with the issue at some point.

• CD Rom drive not recognized of the games which are already installed.

  Hi, I have a similar problem.
  But let's start at the beginning.

  About 5 months ago, I bought a game. It did not work properly. After a month without playing, I wanted to have fun again. And here it starts.
  I clicked on the game icon and the message "' Please insert the correct dvd - rom, press OK and restart the application".» And that's all. So I tried to run every possible way, my two dvd-drivers, then I uninstalled and installed again first on one, on the second disc, but nothing new.
  The thing is, that she even download necessary patches and computer, he sees (in my computer). But every time I want to play appears this irritating message.
  Pilots celan are the disc has not yet a little dust on it.
  On my brother's computer, it works perfectly.
  My computer system is Vista, but I don't think that this has something to do with it.

  Please, please help.

  Hi Neilameane,

  Thanks for posting your questions to answers.microsoft.com

  Just to let you know, I moved your post to

  http://social.answers.Microsoft.com/forums/en-us/vistagaming/threads?page=3

  to place it as a new question on the community forum.  When has already been answered in a previous question, less than MVP and moderators will seek to these posts, so when something new happens on these positions they get very often over looked.  Sometimes just to reference the URL and post a new question will help to get good support on the question line.

  Once again, 'Thank you' for the display of answers.microsoft.com

  Article which was featured on the forum on this link;  Reset you the upper and lower filters?  A big question really to ask, does your system recognizes the other DVD/Cd?

  Here's how to reset the upper and lower filters for the DVD;

  Be sure to have a good restore point before you do the steps described in this article.

  You can follow the steps below or click on this link to go directly to the Knowledge Base article and run the FIX for this issue.

  http://support.Microsoft.com/default.aspx/KB/314060

  Fix it myself

  Important this section, method, or task contains steps that tell you how modi...
  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in Windows
  
  This problem is due to two Windows that have been corrupted registry entries. To resolve this problem, you must use the registry editor to delete the corrupted registry entries. To use this method, you must be running Windows as an administrator. If you need help, check that you are an administrator, visit the Microsoft Web site at the following address:
  http://support.Microsoft.com/GP/Admin (http://support.microsoft.com/gp/admin)
  Back to top

  Microsoft Windows Vista

  1. Click Start
     and then click all programs.
  2. Click Accessories, and then click run.
  3. Type regedit and then click OK.
     If you are prompted for an administrator password or a confirmation, type the password, or click allow.
  4. In the navigation pane, find and then click the following registry subkey:
     HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
  5. In the right pane, click UpperFilters.
  
  Note You can also see an UpperFilters.bak registry entry. You don't have to delete this entry. Click UpperFilters . If you do not see the UpperFilters registry entry, you may still have to delete the LowerFilters registry entry. To do this, go to step 8.
• On the Edit menu, click delete.
• When you are prompted to confirm the deletion, click Yes.
• In the right pane, click LowerFilters.

  Note If you do not see the LowerFilters registry entry, unfortunately this content can't help you. Go to the section "next steps" to learn how you can find more solutions or more help on the Microsoft Web site.

• On the Edit menu, click delete.
• When you are prompted to confirm the deletion, click Yes.
• Exit Registry Editor.
• Restart the computer

Please keep us informed if, in addition, help is needed.

Debbie
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

• 12 c CARS bug or I have to fix ist: "PRVF-5150 < DRIVE > not valid path."

  Hi, after many problems with the installation of 12 c first BECAUSE I am now a bridge, I have one problem left.

  My system:

  2 knots, with ASMLib

  Storage: netapp

  I created disks ASM, oracleasm say that everything goes well on both nodes:

  [root@dbb-n15-01 /] # /etc/init.d/oracleasm listdisks

  DISK01

  DISK02

  DISK03

  DISK04

  DISK05

  DISK06

  DISK07

  But the Oracle installer condition tests says:

  PRVF-5150 < DRIVE > not valid a path

  Can I gnore it? Unter 11 g BECAUSE I know, that there was a bug, but I thought it's fixed...

  Thanks for your help.

  Greetings from Berlin

  So, I ignored the Message After checking with oracleasm that everything is ok. The installation of the grid completed without error.

• I have windows vista Home premium 64-bit installed on my sony vaio cs36gj, which was not install updates. Or running fixit is. How updated?

  I have windows vista Home premium 64-bit installed on my sony vaio cs36gj, which was not install updates. \niehter is running thing fixit. How updated?

  Hi Vishal,

  1. what happens when you try to install Windows Update and the fix, you get any error message or error code?

  2 have you made changes on the computer before this problem?

  3 is the limited issue during the installation of specific updates?

  Problem when installing windows update, see the following Microsoft article.

  Cannot install updates in Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2008 R2: http://support.microsoft.com/kb/2509997

  Solve common installation issues in Windows Update, Microsoft Update and Windows Server Update Services: http://support.microsoft.com/kb/906602

  
  Notes:

  The following steps include changing the system registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  Back up the registry: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

  CHKDSK: Data files that are infected can be cleaned by removing the file completely, which means that there is a risk of data loss.

  Microsoft safety scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again. The data files that are infected can be cleaned by removing the file completely, which means that there is a risk of data loss.

  Keep us informed on the status of the issue.

• I bought Photoshop previously, which was an installation CD, but I just got a new computer, which is not a hard drive. How can I reinstall the program?

  I bought Photoshop a couple of years, which was installed by the CD. However, I just got a new computer, which is not a disk drive, so I can't reinstall the program. Is there a way I could download it with the serial number, so I can still have the program on my computer?

  Available downloadable Setup files:

  • Suites and programs: CC 2015 | CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
  • Acrobat: DC, XI, X | Suite X | 9,8 | 9 standard | 8 standard
  • Captivate: 9 | 8 | 7 | 6 | 5.5, 5 | 1
  • Cold Fusion: 11: 10 | 9.0.2 version 9.0.0, 9.0.1, 8.0.1, 8.0.0, 7.0, 6.1, 6.0, 5.0, 4.0
  • Contribute: CS5 | CS4, CS3 | 3,2
  • FrameMaker: 12, 11, 10, 9, 8, 7.2
  • Lightroom: 6.4| 6| 5.7.1| 5 | 4 | 3
  • Photoshop Elements: 14,13,12,11,10 | 9,8,7 win | 8 mac | 7 mac
  • Premiere Elements: 14,13,12,11,10| 9, 8, 7 win | 8 mac | 7 mac

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

• VMware Workstation 6.5.1 - Drive error is not ready - Everytime - 5 other computer - 5 different installer downloads

  Hello

  It seems that whenever I have to "turn on" a virtual machine using VMware Workstation 6.5.1 I get an error disc is not ready . Give me continue, ignoring and Cancel the options I always support on continue.

  I think it's a memory allocation error.

  I tried it on 4 different computers and with 4 different operating systems. Every computer that I tried on was completely different, custom built computers. Except one, which is a laptop, to be precise, Dell Inspiron 700 Mr. others included Windows XP x 64 (on Computer1), Windows Vista x 64 (on Computer1), Windows XP (on laptop), Windows XP (on computer2) & Windows Vista (on computer3).

  Whenever I got it redownloaded from the VMware Web site, certainly isn't a problem on my end.

  One of these computers/OS I get an error similar to this one, below, when I turn "on" a virtual machine;

  

  Please fix this bug in your next version of VMware Workstation.

  Thanks in advance,

  Panarchy

  See this thread:

  http://communities.VMware.com/thread/105764