Windows drive not ready

Similar Questions

• When I copy to the disc, I get the following error message: Windows – drive not ready

  Below it this box is a red emblem with a X white.  The message is: Exception Processing Message c00000a3 parameters 75b6bf7c 4 75b6bf7c 756bf7c and option buttons here's this message: Cancel try again continue no matter which option I choose, the box disappears for a few seconds and comes back with the sound "attention".  I am usually able to to copy, but sometimes the file will freeze when I try to use the data.  I can't close the message box.  Anyone know what is the problem and how can I fix?

  Hi tbenton1946,

  What application you use to burn the data?

  What is the service pack installed on your computer?

  1. you can access the link below and run the automated Troubleshooter to fix the CD and DVD, read and write the questions and check if it helps.

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  2. try the steps from the link below: how to troubleshoot problems that occur when you copy data on a CD - R or CD - RW optical disc in Windows XP:http://support.microsoft.com/kb/324129

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• drive not ready _ stopped system

  I have an Intel computer with windows xp pro, ver.2002, service pack 3. When I try to bring it to the top, the screen reads Media test failure, check cable. Exit Intel PXE ROM, don't drive not ready-system stopped. What has caused this? & How can I fix? I'm not for wise on computers but eager to learn, any suggestions? Furthermore, the cables are connected good.

  "merlin21" wrote in message News: de7da812-de4e-4ace-bbdb-6605739d589f...

  I have an Intel computer with windows xp pro, ver.2002, service pack 3... When I try to bring it to the top, the screen reads Media test failure, check cable. Exit Intel PXE ROM, don't drive not ready-system stopped. What has caused this? & How can I fix? I'm not for wise on computers but eager to learn, any suggestions? Furthermore, the cables are connected good.

  Ensure that there is no floppy disk in the floppy drive if equipped and no CD/DVD in the CD/DVD drive but it looks like a hard drive failure.
   
  When you turn on the computer you hear the spin drive upward? (remove the cover from the computer, but do not touch anything inside).  If it is not rotating until power off (hold power button down until it stops.)
   
  Pull out the power cord from the computer, touch the metal casing of the computer and (assuming a type IDE disk) can detach and reattach the power cord 4 son to drive.  Also carefully Disconnect the Ribbon data cable and attach again carefully.  Make sure that the Ribbon on the motherboard connector is also firmly committed.
   
  Connect the computer again and the power up.  Drive spinning up to now?  Lol bad disc.  Hope you have a backup.  Turning to the top but still the same message?  Hope you have a backup.  Take the computer with all the disks for computers and a reputable Studio programs (big box stores are not trustworthy) repair and hope that they can get down your data and rebuild the machine.

• Drive not ready. Have you ever seen this happen before?

  I'm new to vmware and I have installled just vmware tools for I can have a full screen. Now whenever I'm starting my Ubuntu VM (my only), I get this message:

  "Tvmware - vmx.exe - drive not ready".

  The drive is not ready for use; its doors can be opened. Please check the A: drive and make sure that a disk is inserted and that the door is closed. »

  I can click on Cancel, Try Again or continue. Each option takes me to the same place, namely my Ubuntu vm... It is not cause real problems I know. It is more an annoyance.

  So has anyone seen that happen before or know how to fix? Thanks in advance!

  Welcome to the community,

  Take a look at the virtual machine settings and disconnect the virtual disk. If this does not resolve the problem, please provide the latest vmware.log file of the virtual machine file. Maybe this can help.

  André

• drive not ready message "the drive is not ready for use check the a drive, etc.".

  as soon as I connect my camera to transfer the photo I get following message

  The drive is not ready for use: the door can be opened. Please check the a drive; and make sure that a disk is inserted and that the door is closed.

  I can't get rid of this meaasge if I have to cancel it reappears 10 seconds later it just won't close very boring

  Hello

  What is the number and the model of the computer?

  You have the computer floppy drive?

  Were there any changes made on the computer before the show?

  Follow the steps:

  Method 1:

  Remove all external devices connected to the computer such as printers, scanners and external USB hard drive and check if the problem persists.

  Method 2:

  Check the BIOS setting and also, I suggest you to update the BIOS. To update the BIOS, contact the manufacturer or the manufacturer of the access Web site.

  Note: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• bug: 'drive not ready' which was already fixed bug is back

  When you try to start VMware so that you have mounted a vmdk with vdk.exe jobs appears an unnecessary error message / false.

  It is harmless but annoying as it prevents automatic start of virtual machines

  The bug was present in the earlier version but had been fixed with 6.5.0, if I remember correctly.

  Now with 7.0.0. He's back.

  Whereas from VMware seems to check all drives available - and it merges if it finds something unexpected.

  Suggestion: ignore all this. It is not really important if a vmdk is mounted everything by starting the workstation.

  See screenshot of the error message-
  
  ___________________________________

  VMX-settings- VMware-liveCD - VM-infirmary

  Maybe this indication could be useful for you: http://pavlovich.org/musings/?p=3

  ---

  Paul Svirin

  Software developer StarWind ( http://www.starwindsoftware.com )

• Satellite L30-114: driver not designed for this platform when installing IDE controller

  Hello! I have the satellite L30-114, I bought months ago. I have Win XP SP2 with all updates and the bios 2.3.

  A few days ago, I tried to reinstall the drivers for the ide controllers. I have delited in "Device Manager" and restart the system. After you start windows normally are both installed PCI - IDE controllers, then find ide channels (primary and secondary ide channal on ich) and the strange thing happens here: instead of the normal installation of these 4 channels, window "driver not intended for this platform". and after each reboot those devices Installing, to give me 4 windows "driver not intended for this platform".

  Now in Device Manager, I have 2 controllers IDE standard normal, and not 4 channel IDE working with yelow «!» The funny thing is that I not install new ide drivers. Drivers are the same who worked before reinstalling. Now the computer works, but is worth than before. on the toshiba site there is no driver Ide "planned for this platform.

  Anyone know how can I solve this problem? or where is located this driver? or what chipset whith this controller model in this notebook?

  Hello

  In my opinion, there is no reason to do something like that. If the laptop works well let it go. Go to the Toshiba download page and download driver chipset for your laptop model and install it manually.

• After the 24 Firefox update, Windows 7 64-bit breaks on reboot. The network in the taskbar icon is not ready (blue circle stopped).

  After 24 of Firefox update, Windows 7 breaks after the reboot. The network in the taskbar icon is not ready (blue circle on the wireless network icon). But I can't do much. I can't open the network and sharing Center (never opened). Even the Task Manager hangs when I click to show processes from all users. I have to do a system restore for a network working again. I never even launched Firefox.

  Wow... I finally have the solution. Windows updates have been applied at the same time I updated Firefox. Bluetooth driver is what broke (which is part of the Centrino wireless). I ended up installing the latest driver from Intel, Windows Update, and then update Firefox... and all is well.

  I thank very you much for all your help. Take care.

• The lack of CD/DVD drive - not recognized by windows or other programs

  help-tried several fixes m/s and fix it but did not help. Here are a few messages I get: when in the details of the driver for my Sony DVD + RW AWQ160s - update drivers: here are 2 notches and uncked 2, one by Sonic Solutions and a Roxio time saying no digitally signed (that would be a problem)?  also when I look at update or install the updated driver, after that search, I get this is the best driver for this device - I don't have this device Ouch!  Without my CD drive E work of course I can't even try reinstalling drivers/utilities cd... can someone help this computer incompetent gal?  I'm ready to wipe and reinstall vista I have other problems like IE does not and ms word does not always.  I did go back several times, and perhaps not far enough back but had a Trojan horse and do not want to deal with it again.  thx for any help

  Hello

  (1) would you please provide more information about the problem you are having with word and Internet Explorer?

  Method 1: You may need to reinstall Roxio on your computer, please see the article below for programs that can cause this problem:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base.
  How to back up and restore the registry in Windows

   

  Method 2: If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• attempt to copy to the windows drive is not an unknown error occurred (-54)

  When syncing my iPhone, I get the following error message near the end of the processs of 6s + 128 GB

  attempt to copy to the windows drive is not an unknown error occurred (-54)

  
  

  Someone has an idea what is the cause to happen and what I can do about it?

  Thank you

  Hello

  Here is a solution for your problem

  http://www.IMore.com/having-trouble-syncing-iTunes-after-updating-Windows-10-her're-your-fix

• Want J010dx m7: windows will not start until after full recovery of the system with new HARD drive

  Hello world

  I need help here.

  My HP envy m7 J010dx works perfectly with my original hard drive (1 TB).

  I am preparing a second HDD (NEW 320) as backup.

  I took off the Moose HDD (1 TB) and replace it with the NEW HARD drive (320GB) and try to do a full recovery of the system with the HP recovery DVD.

  After full system recovery and laptop computer needs to be restarted in order to continue, the laptop keeps restarting on the logo of windows 8.

  I think it says device not found Boot. Also a test using the UEFI tool material HP and all pass.

  Replacing the NEW HARD drive with the original of the old HARD drive and it start normally.

  What can go wrong here in this case? Thank you very much for the help.

  Concerning

  John

  OK, I read through the thread and this is my point of view on this based on works including restore process with the user created a recovery (UCRDs) media which the user indicated that they used.

  If you just want to jump to the conclusion at the bottom, you can see my opinion. If you want to know 'why' Please read the entire post.

  Model No.: m7-j010dx

  Product #: E0K83UA #ABA

  Ships OS: Windows 8 (64-bit)

  Recovery HP part No. Kit: 730336-002 (3 DVDs + extra)

  User replaced the HARD drive with a 1 TB hard drive 5400 RPM with HP ProtectSmart hard drive Protection a new hard drive is a Seagate Momentus 7200.4 ST9320423AS 320 GB 7200 RPM 16 MB Cache SATA 3.0 GB / s 2.5 "Notebook internal hard drive.

  With the help of UCRDs sent media recovery media (SSRDs):

  When the UCRDs are created, only the drivers for the HW operation (this is a critical point, that I will look later) are burned to the user created a recovery media.  Consider this a snapshot of the current HW, the base drivers and software applications.   If you change the HW on your laptop or desktop where the additional device requires a different driver for these features, a few questions you might - recovery process could stop because he can't find the right driver, a blue screen, a lack of start-up or other unstable system.

  A few years ago, I had a PC that would not recover because the Blu - ray (ODD) optical disk drive did not work.  I replaced the WEIRD Blu - ray with a generic DVD/CD burner into the new part of Blu - ray is presented.   I got the PC using SSRDs thinking I would put some time and just install the Blu - ray after the PC has been recovered.   The PC recovered and when the new Blu - ray showed I installed the unit and guess what?  All PCs have shown in Device Manager and applications was a generic ODD - no Blu - ray capability and ability to read Blu - ray content in the default HP provided for multimedia applications delivered with the PC.  Applications were there but no Blu - ray capability.

  Huh?  It looks that I did not put any time at all.

  I inserted the new Blu - ray ODD and distributed recovery with the HP SSRDs.

  After recovery, I had all the Blu - ray drivers and applications supported Blu - ray.

  The difference between UCRDs and SSRDs:

  UCRDs provide a glimpse of what is installed and functional both disks are created.

  Version Digest of the player on what is happening with SSRDs to retrieve a PC (before Windows 10):

  SSRDs have all the drivers for all the HW and SW qualified for the unit.  There may be several drivers for hard drives, different types/screen resolutions, sides, etc.  Based on the characteristics of the specific laptop / desktop a process is run called "Do / don't.   After entering the recovery SDRD, the Notebook media boots to Recovery Manager.  The first step is a raw copy of all the contents of the disc on a temporary partition.  Following the Do / do not process looks at the characteristics of this specific unit and remove all other drivers and applications not used by this device.  Drivers and the only successful applications are the features supported.   And then, the new operating system and recovery partition is created.   The PC end recovery of cleaning process and restart the laptop / desktop. And, Yes, you guessed it, if you create the user created a recovery media, you only have the drivers for HW devices and applications of HP on the PC at the time.

  So, that being said, what could be the cause/solution?

  Hard drives can be different enough so that a different driver (not the UCRDs) is necessary for the newly installed HW.

  The SSRDs are supported on the new HARD drive installed?

  I don't know, I have an office boy, and I have not tried on this model of laptop.

  If you have / acquire SSRDs, I recover the laptop with the new installed HARD drive and see if it works.  It may or may not.  I don't know what drives were qualified for this laptop.

  If this does not work, the last option is cloning via USB connection (old HARD drive in the PC, new HARD drive connected to a USB 3 via the SATA Adapter (dongle) USB port, install or download software cloning and cloning the old HDD to the new.)   I just did this on the two older Windows 7 computers laptops using a SanDisk Ultra kit.  He has worked on both units.

  Conclusion:

  I don't think that the problem is caused from a HARD drive of 1 to a 320 GB HARD drive, as it meets the minimum specs for a complete installation.  I think the problem is related to the use of UCRDs to retrieve and the UCRDs do not have the HARD driver/firmware/application disc.

  But then again, I know.

  I am an employee of HP...

• Bluetooth is not ready after waking from sleep on Windows 7

  After updating my Tecra M10 Windows Vista x 64 Enterprise to Windows 7 x 64 enterprise, sometimes, when I wake up the laptop from sleep, Bluetooth is not ready.

  Hibernation does not solve the problem, he needs a reset which is a problem for me because I usually have a lot of open applications.
  In this case, the only Bluetooth devices in Device Manager are:

  * Bluetooth RFCOMM
  * Bluetooth USB Controller-5 at TOSHIBA

  When everything works well, the Bluetooth devices in Device Manager are:

  * Bluetooth RFBUS
  * Bluetooth RFCOMM
  * Bluetooth RFHID
  * Bluetooth USB Controller-5 at TOSHIBA

  How can I restart Bluetooth without having to restart the entire system? Turn wireless on and off the silder side does not work.

  Thank you
  Paulo Morgado

  Thanks for sharing!

• Windows does not load on a Satellite A350 with 500 GB Seagate external HARD drive

  There is a problem with this laptop, A350-043 running Vista Edition Windows Home Premium 64 bit, part number: PSAL6C - 04S 015

  In other words: when it is connected to a 9NK2AL-510 SEAGATE 500 GB SATA DRIVE EXTERNAL USB (s/n: 5QG1YH1E) Windows will not load, it will up to and gel just before the green movement of the bar. If the USB cable is released and handed over in a second, Windows continues to load normally and all is well.

  Otherwise, the operating system will have up to 15 minutes to load. Looking in the BIOS features, there is no option to boot from USB available, so it can not be disabled. I have updated the BIOS of Toshiba to the latest version without any change in this issue.

  I tested and confirmed that the problem persists no matter what USB port is used.
  The external drive is fully functional, and there is no error or problems with it loading Windows. I reported this problem to Seagate so that Toshiba in the hope that a solution can be offered on this, but has not heard back on anything either yet.

  Do you mean that the laptop needs 15 minutes to load the Windows operating system, even if the external HARD disk is not connected?
  It sounds weird, and I doubt that this can be related to any software problem

  First of all, you should check the boot order in the BIOS the USB should be set at the last or last position.
  Second, you should check if the same problem persists even after a fresh install of the OS in some cases, that the start-up procedure could be affected due to the process software and installed background.

  But if the new installation of the operating system is not enough and if the issue persists then I guess a hardware problem (motherboard?) could be the reason for that and, therefore, a technician of the laptop must be contacted!

  That s in my opinion

• Replacing the hard drive T60 - Windows does not recognize the hard drive

  Hello all, new to the community of Lenovo. I have a T60, but also the latest Lenovo Edge. HD crashed on the T60 and it will boot is no longer. I just bought a 500 GB WD without doing a lot of research. When trying to install Windows 7 (I had already updated the T60) it will not recognize the new drive - Windows does not drive at all. Is there a way to get the Lenovo to recognize the WD drive? Thanks in advance for any help.

  Looks like you're doing something wrong, if the drive is a SATA it should work, install it and boot from your windows installation DVD and it will be the installation drive and shaped for you, or you can optionally set the partitions manually when you are prompted to do so. If you try to do something unusual such as transfer windows on the old drive then you will need to explain exactly what you did because I see no reason it should not work. Infact I did it several times myself.

• HP Pavilion g7-2043sf: Windows could not find a driver for your network card

  Model: HP Pavilion g7-2043sf

  Product number: B1P51EA #ABF

  Today, I did a clean install of Windows 7 on this laptop and I can't connect to internet via wifi. When troubleshooting I get this message:

  Windows could not find a driver for your network card
  Windows does not detect a network card is installed correctly. If you have a network card, drivers for the card cannot be installed correctly.
  Install a driver for your network card
   
  Collection information
  Windows Version: 6.1
  Architecture: amd64
  Time: Thursday, December 24, 2015 12:34:16

  In Control Panel, I found this information:

  Ethernet controller: the drivers for this device are not installed (Code 28)
  Hardware ID
  PCI\VEN_10EC & DEV_8136 & SUBSYS_1844103C & REV_05
  PCI\VEN_10EC & DEV_8136 & SUBSYS_1844103C
  PCI\VEN_10EC & DEV_8136 & CC_020000
  PCI\VEN_10EC & DEV_8136 & CC_0200
  
  Network controller: the drivers for this device are not installed (Code 28)
  Hardware ID
  PCI\VEN_1814 & DEV_539A & SUBSYS_1839103C & REV_00
  PCI\VEN_1814 & DEV_539A & SUBSYS_1839103C
  PCI\VEN_1814 & DEV_539A & CC_028000
  PCI\VEN_1814 & DEV_539A & CC_0280

  I visited this side: http://support.hp.com/us-en/drivers/selfservice/HP-Pavilion-g7-2000-Notebook-PC-series/5226249/model...

  I need all drivers of network?

  Thank you.

  Hello:

  You need these drivers...

  This package contains the Realtek driver local area network (LAN) that allows the NIC (NIC) Realtek chip in the notebook models that are running an operating system supported.

  File name: sp55979.exe

  This package contains the installation package driver for Ralink Wireless LAN to laptop models controllers that are running a supported operating system.

  File name: sp58586.exe