Call SCV-express to any endpoint

Similar Questions

• Call Manager Express ATA187 Firmware update

  Hello

  I recorded with Call Manager Express 9.0 to ATA187 but I have a problem for outgoing calls using DTMF, I tried to put dtmf-relay into the pool of register of voice but without success, so I decided to update the firmware.

  the problem when you go to download page you will find a .zip to the file not as before managing the .zup file and the upgrade of the firmware for the express appeal not found in any document because there is no way to upgrade through phones analgo

  No idea how upgade using any way?

  Hi mrmhar1408,

  You must upgrade the ATA 187 for the latest firmware SIP (9.2.3) using this load file, ATA187.9 - 2-3 - 1.loads. It is in the zip file available on the download section of cisco.com to the ATA-187, the name of the zip file is cmterm - ata187.9 - 2-3 - 1.zip.

  The process of upgrading of the ATA and SIP phones 187 s in SIP via CME are listed here. The process is essentially the same for phones and ATAs.

  http://www.Cisco.com/en/us/docs/voice_ip_comm/cucme/Admin/Configuration/Guide/cmeinstl.html#wp1067416

  Note that you must also have the load the copied file first in memory flash TFTP server, that would be your router CME flash.

  HTH.

  Kind regards

  Stefano.

• Passing parameters to the method call in expressions of value

  JDeveloper 11.1.2.1.0 does support the feature of passing parameters to method calls in expressions of value in JSF pages? AFAIK this is JSF 2 version it and it should support this feature. Unfortunately when I put in a JSF page the following tag
  < h:commandLink value = "#{row.employeeId}" action = "#{empBean.showDetails (row)}" / > "
  The page does not work. Any ideas on this point?
  
  Thank you to everyone.

  Hello

  The functionality you need is defined in JSR 245.
  If you need to wait for it to become part of the standard, it will be included in JEE6
  I don't know if 11.1.2.1.0 uses JEE6 standard...
  You can try this other thing,
  http://www.coderanch.com/t/213290/JSF/Java/why-JSF-calls-method-parameter

• Phone to the Call Manager express license

  Dear,

  Is the license of phone required for Call manager express or the license on the bridge of voice enough to operate the phones?

  Kind regards

  A device license is required for phones on CME. Reference numbers

  FL-CME-SRST-5 =.

  FL-CME-SRST-25 =.

  FL-CME-SRST-100 =.

  Aerts.

• HWIC-AP more Call Manager Express?

  It took me some time and many transfers of tftp to finally find an IOS which works very well with the HWIC-AP (wireless access point module) for a router in 2801.

  What I was asking: is there an IOS which supports both HWIC-AP and also includes the Call Manager Express (CME)?

  What feautures would you find using the IOS search engine?)

  Thanks for all the ideas.

  Marc

  Use the IOS 12.4 (2) T1 or later to support the CME and HWIC-AP

• Call SCV (NAT) installation failure

  Hi all

  We are facing a problem to call between 2 point of termination with the following configuration:

  Control of VCS (192.168.10.5) (coordinated at 10.1.10.5)

  Video 1 endpoint (10.1.1.5 - sign up for VCS 10.1.10.5)

  Video endpoint 2 (10.1.2.5 - sign up for VCS 10.1.10.5)

  Direct call between endpoint 1 and endpoint 2 works fine.

  Once point endpoint registered for control of VCS (using the public IP 10.1.10.5).  The call using endpoints id H323 or SIP URI is not possible.

  As far as I understand it, the problem may come because, when configuring call Endpoint1 will try contcat endpoint 2 via VCS.  endpoint 1 will send request to VCS (step 1) with the source (SA) 10.1.10.5 - destination address (DA) 10.1.10.5 address.  then VCS will send step 2 of the configuration of the call endpoint 2 with source (SA) 192.168.10.5 - destination address (DA) 10.1.2.5 address.  That NAT is not that for DA, the the IP address of VCS receives no teeth.  The end point 2 will try to send packets back call configuration VCS using 192.168.10.5 as da it will fail, because is not the IP private VCS.

  Can someone advise if he alreadymake such configuration (using the ip address using a NAT of the VCS control)?  and if my interpretation is correct?  Thank you.

  Kind regards

  Ahmed

  Call configurations do not work because the SIP SDP is negotiating in the media, and the IP within the PDS is not modified with the NAT. Overall, this isn't a drawing for this reason supported. I've seen some cases with it works (sometimes) using ALG and keep all unencrypted calls, but this solution is hit or miss.

• Call the procedure before any operation of DB

  Hi all
  
  I currently have an application configured to use a data source JDBC for all its transactions in database. I was wondering if it is possible to call a db procedure every time a new database connection is created for use.
  
  My scenario:
  
  All users are authenticated through an LDAP service and I store the user name and other relevant information on the success.
  
  The DB is a procedure established to a user name for the database user as long as the parameter passed in view (s). This is necessary for all our inherited audit information on all the relevant tables to be filled.
  
  So basically I have to call this procedure before any other transaction of db is called.
  
  I have successfully deployed the dynamic JDBC example in the past, but I was wondering if anyone knew another way with the given scenario.
  
  Any help is appreciated.
  
  Thank you!

  Maybe this can help http://blogs.oracle.com/jheadstart/entry/row_level_security_using_vpd_a

• call an express vi interface programmatically

  What I'm trying to do is to use scripture to interface configuration measurement file express vi (and features) at run time.  I want to allow changing the settings onfiguration during execution of the vi.  I tried to open the interface directly from the DLL (in vi library) and it opened, but reported bad reference of vi.  Can I extract all the vi of the dll to use in my program?  Is there an easy way to grab all the vi dependent libraries?  Please advise if I take the wrong approach.

  Thank you

  Scott

  ScottAdon-

  What configuration settings to make adjustable? You can right click on the writing of measure File.VI and click Open the front panel. This converts the Express VI subVIs that are configurable. You will have to go to sift through the subVIs to find the settings you want, and then add in as parameters in the component of connector but then after that you will be able to plug in control over what can be adjustable. This is not supported, but it can be easily done if you just look at the code and understand how each parameter. Hope this helps!

• Call Manager Express has no type 6961

  Greetings

  I have a 1861 with cme 7.1 router (I think, I got this from the show - telephone services) and when I try to add a new phone 6961, I did not have this type of guy.

  Is it something about the compatibility of the cme ip phone or am I missing some configuration?

  Thank you

  Augusto,

  Support for the 6961 started CME version 8.0 for SCCP and 9.0 for SIP

  See the CME software compatibility matrix

  http://www.Cisco.com/en/us/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm

  Kind regards
  Alex.
  Please evaluate the useful messages.

• the call for a Vision Acquisition Express VI into a loop

  Hello. I worked on a project for a while now, and I seem to come to a brick wall. I'm relatively new to IMAQ, but I think I understand some of them.

  We will call our test user Bob.

  Bob must be able to see what the camera sees, and when the camera focuses on a barcode, Bob must press a "Capture" button, which will be the last image of the continuous acquisition and use this image for reading codes bar and later analysis of the data.

  Bob is however facing a problem. Its block diagram is implemented in two different ways, both giving the same result. (see attached photos). It is within a sequence structure, that is in turn inside a while loop, which can be exited at any time. To prevent an automatic bike in the great loop, the first image of the sequence above is a structure of the event that allows the process to continue when you press a button "New Capture". What is going on? The first time through the sequence, Bob gets good results. However, after the execution of all the while loop, the image of the camera, which should be displayed in harmony with what the camera sees up to the "Capture" button, is just a white background.

  What could be the cause of the express VI do not qualify the second time through the loop and beyond?

  Thanks in advance.

  (EDIT 1: image of the façade was added after the problem occurred)

  Still, this does not seem to solve the problem. A capture finished as determined in the Express VI is the only way I found to call the express VI an infinite number of times. It works for my case, so I'll close the debate.

• Calls disconnected endpoint

  I had a client ask about the following situation.

  They have disconnected a C Series codec in one of their rooms. When calls were made to the endpoint offline, rather than fault, he ended up in the MCU. I don't have the means of laboratory to try to recreate it, but can someone shed some light on why this happens?

  Thank you

  Robert

  Hi Rob - your client to make a call to the E164 Alias of the system and then it routed to the MCU?  Could be the E164 alias is close or is the service prefix MCU and sound recorded as GW at any GK your help.  Would be useful to see if there is a correlation between the two, or if your client made up [email protected] / * /, and the alias is always nearby the GW service prefix.  This can also occur as well.

  It would be able to verify?

• Is received call from Virtual PC Doctor scam, any threat to the security of my PC?

  I was called by Virtual PC Doctor around 14:00 today. They knew my name, address and telephone number and went through their usual field. When they asked me to go to my computer and tell them what was on the screen, I told them that I had to check out them before we all went further and ended the call. Is there any other action should I take to protect my safety?

  Hidden Hi Bandit,
   
  Microsoft will not unsolicited calls to help you with your computer. Make sure you hang up the phone the next time that you receive such calls.

  More information on:

  I received a phone call / email from someone who says that my computer has been infected by a virus

• I can't find any directory called C:\WINDOWS\SYSTEM32\MACROMED. Can you advise me?

  I am running Vista 32 bit Service Pack 2 OS (windows Vista Home premium).  I recently downloaded "Adobe Flash Player 10 Active X".  It does not run is displayed for me select a desktop ICON.  I can find it in my control panel under "programs and features" where I can uninstall it if I want to.  I found a website that said it was a problem knowledge and my advice on how to solve the problem by following the methods described: 1. navigate to: C:\windows\system32\.   2. navigate to a directory called "ACROMED.  It is my problem, I do not have a listed directory called "ACROMED.  In any case after I do that I am to run flasutil9b and run as administrator, then follow the prompts through the installation of flash wizzard.  What I am doing wrong?  Unfortunately I am not computer enough to continue the process.

  Thank you to everyone out there that can help

  Flash Player is not a stand-alone program. It is a browser plugin; do not find a desktop icon or start menu for it.

  The instructions you found on the web are for Flash Player 9. Use these instructions to solve problems of Flash Player 10.

  http://kb2.Adobe.com/CPS/191/tn_19166.html

  Flash Player is installed in the C:\Windows\System32\Macromed\Flash directory

  The ActiveX is for Internet Explorer. If you use Firefox or Opera, you must download the NPAPI plugin as well.

• VCS Express with CUCM 10

  Hello

  There is a lot of confusion on Express C/E & VCS C/E, if anyone can confirm my following queries:

  With VCS VCS & Express control every endpoint to register with VCS control (no participation required CUCM or VCS control can't integrate with CUCM)?

  With Highway Core & edge that every endpoint is record in CUCM & CUCM will record Expressway Core?

  For calls B2B & movi Jabber, that we must have Expressway Center/periphery, VCS control/Express IS NOT support jabber movi & called B2B?

  Software Express C/E & VCS C/E are the same, but the licenses are different?

  Our clients have obtained

  1 x control VCS licensed

  1 x Express VCS under license

  1 x ISDN gateway,

  1 x TP driver

  1 x TP management suit.

  Kind regards

  Francisco

  With VCS VCS & Express control every endpoint to register with VCS control (no participation required CUCM or VCS control can't integrate with CUCM)?

  Yes, no CUCM is required, endpoints can also enroll in the VCS-E or it could register SIP to VCS - C proxy endpoints. A parallel installation of VCS CUCM with a trunk should also work with todays versions.

  The VCS will be only support standards basis of endpoints SIP and H323, its main purpose

  a for video settings. You won't be able to use it to register, provision or use of Cisco IP phones with it.

  With Highway Core & edge that every endpoint is record in CUCM & CUCM will record Expressway Core?

  See the C & E highway as a single unit to the external communication. The registrations are transferred by proxy

  CUCM outside.

  But that also means, you can't register 3 party at the highway and even end points

  Cisco endpoints must support the installation of the fast track C & E.

  The highway also runs things like XMPP for Jabber.

  For calls B2B & movi Jabber, that we must have Expressway Center/periphery, VCS control/Express IS NOT support jabber movi & called B2B?

  The C & E Highway can also manipulate calls business2business or another sip trunks / h323, but this infrastructure requires the media license.

  B2B calls also works very well with the installation of VCS.

  If you are talking about how to provide Jabber accounts and video Jabber:

  There are video Jabber (which is implemented by TMS and VCS) and Jabber (i.e. led CUCM) there.

  If you are talking about outside calls that he can just be regarded as regular b2b external calls.

  then they be it work with VCS or motorways on the site of the end.

  Software Express C/E & VCS C/E are the same, but the licenses are different?

  It is correct. Licensing Expressway is more attractive for users CUCM, but you already have

  have SPRDD in place that should work in all cases well.

  With CUCM, you get licenses Expressway in any case. So according to the type of use, you.

  B2B, internal calls... you can add a configuration of fast track to Jabber and the stuff of office home and

  use the VCs to B2B and part 3 records.

• How to connect the Airport express as an Extender for airport extreme to El Capitan

  I have a model extreme A1521 airport and a model express airport A1392 and upgraded my OS to El Capitan. I want to use the express as an Extender for the extreme because my old House is long and has thick walls. My problem is that Airport utility will not 'see' the express, regardless of its proximity to the main router (extreme). I tried to move and reset.

  Of course, as soon as I get the utility to see, I need instructions on how to configure the express as a booster for my extreme.

  Any ideas?

  Unplug the Express and put it in the same room as the AirPort Extreme.

  Put power on the Express for a few minutes, then hold down the reset button on the back of the Express for 7 to 8 seconds and release.

  Allow a minute for the Express to restart

  

  Click the WiFI icon at the top of the screen of the Mac

  Look for an announcement of the new AirPort base station

  Click directly on the AirPort Express Terminal

  

  When you click on AirPort Express, the "Wizard" will open and take a few seconds to analyze things, and then see a screen that looks like the figure below, except that you can see your cameras.

  

  Type a short and simple name that you want to call the Express

  Click next

  The installation wizard will take care of everything for you

  When you see the message Setup is complete, unplug the Express and move to halfway between the AirPort Extreme and the area of the House that needs more coverage of wireless signal

  Turn on the Express and you're all set

  Important note... the Express to expand the quality of the signal it receives. About half of the potential speed on the entire nextwork is lost when you extend using a wireless connection between the airports.

  It would be much better if you could connect the Express to the extreme by using wired Ethernet wired, permanent, since there is no loss of signal via the Ethernet cable and there is always a lot of loss of signal through the air, the (thick walls especially) walls, ceilings, etc.