Cannot connect to the admin page of R6400 laptop, only on iPhone

Similar Questions

• LAPN600 could ' t connect to the admin page

  Hello.

  The first time that I also tried to connect to the admin page it worked. But now when I try to connect if I'm lucky, I can log in, but after that I just got "page cannot be displayed".

  I HAV tried to reset the LAPN600 but it dosent resolves the problem.

  Someone at - it more then me that have this problem?

  I found the problem. It was me

  When I tried whit my windows 7 computer was wired and my Windows 8.1 was wireless.

  I found a setting "Access of Configuration management->" Wireless: activate

  So my problem is solved.

• WRE54G cannot connect to the configuration page

  I use WRE54G and I can't connect to the device.  I have connected to my computer via a cat5 cable, but I can always connect to the Setup page.  Right now I'm getting a solid light.  I tried to connect to the unit when it shows the kept my "no internet wireless network
  access and have this problem for a few days.  I tried to use a static ip address and reset the unit, but nothing has worked.  I can't ping the unit either.

  I am very good with computers, but I can't understand this thing.

  What is the model of the router?

  By default the ip address of the WRE54G is 192.168.1.240... So assign ip address 192.168.1.10 subnet mask 255.255.255.0 and default gateway 192.168.1.240 on the computer which is connected to the WRE54G via cable.

  If it's still could not open the configuration page, then restart the WRE, power cycle the WRE and then try again.

• cannot connect on the start page, as the owner.

  computer froze on the star page. cannot connect as an owner.

  Hi mycasmas,

  1. don't you make changes before the show?
  2. the problem persists with other users accounts?

  Step 1: We recommend that you check if the problem persists in safe mode
  a. see Description of the Mode of course in Windows XP startup options
  b. in the menu advanced startup options select Safe mode and press on enter.
  c. connect to your user account.

  Step 2: If the problem does not persist in safe mode, check if a non-Microsoft program is causing the problem
  see How to configure Windows XP to start in a "clean boot" State .
  b. in the article, follow the method 1 and method 2 to find out if any program is causing the problem.
  c. Once you have found the culprit that is the program that is causing the problem, then uninstall it.

  Note: Article, remember to follow 'steps to configure Windows to use a Normal startup state. "

  Visit our Microsoft answers feedback Forum and let us know what you think.

• EA-4500 cannot connect in the configuration page

  I try to connect to my EA4500 Setup page. I have the firmware "cloud connect" and when I get redirected to the "Linksys Smart Wi - Fi" page in my browser, I try to log in as usual. He accepts my username and password, then I get a page that contains a rotating chart and it says "waiting...". "He eventualy expires and brings back me to the login screen. I have tried rebooting my router and it does not help. I also unplugged the modem from the internet connection and entered the main router password, and gives me the same answer that if I tried to connect via the cloud.

  The only thing I can think of would be to do a factory reset of the router, but based on what is happening here, I'm frankly scared that I will never get my router online. I really wanted this cloud thing to work, but if I can get connected I will probably be back to the old firmware. Linksys gave us?

  I tried on several computers in the House and still have the same answer - no access to the router. At the end of the day, I did a factory reset and was finally able to get into the router. It was a pain to have to re - install my router, but at least I got all devalued parameters.

  For memory, the firmware had not changed since the introduction of the services cloud in June/July. I have the same exact firmware I downloaded in July. The only thing that has changed is that Cisco renamed "cloud connect" web interface for "Smart Wifi."  The web interface seems a little faster, but there are still a lot of wait time.

  I must be honest, based on this event, I was ready to go back to the old firmware, however, I'll give it one more chance to see if things will be better, or at least stabilize...

• Classic BlackBerry set up questions - last get cannot connect to the wifi page

  Hi all

  far I have set up 30 + new Blackberry classic but the last issue is that once I have connected to the wifi I can't go through this page and the only options are previous!

  any ideas on how to move beyond this stage so I can complete the set up process?

  understand the question - under the date and the time of its establishment on auto update and this showed February 25, 2015 @ 9.31 am. changed to the current date and time and now I can exploit and set up the phone.

  Hope this helps others.

• Cannot connect to the Eprint Page?

  Try to connect to the Eprint as usual, but I keep getting the following error:

  Ajax submit failed: Error = 403 Forbidden

  This has been going on for 24 hours now and ePrint has not worked since yesterday. Tried pulling the printer offline and back on, disconnect the power supply and the other usual steps. Now, I can't even login to check the printer status or employment. Any ideas?

  Hi stockalugroupe,

  Please try to connect with another web browser (IE, Chrome, Opera etc) and tell me if this solves your problem.

• SBS 2008 cannot connect with the admin account

  Hello

  I have intalled SBS 2008 on my server. Yesterday he installed updates, now I can't connect using my administrator account (it says wrong user name and password). The only way I could log in with my credentials is hollow in Safe Mode.
  The server is used as a controller of domain, MS Exchange and the file and printer sharing. None of these processes work properly. I can access the drives mapped to the user's computer and Office does not connect to Microsoft Exchange.
  I appreciate any help you can give. Thank you.

  Support is located in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Horizon 6.2 to 7 Upgrade issue with the Admin page

  Hello

  I installed my view Horizon 6.2-7 environment. Upgrades seemed well my server my connection to two servers and composer. However when I try to connect to the Admin page it is just a blue screen shows white guard goes round and round. Someone at - he seen this yet?

  Thank you.

  Have you tried VMware KB: accessing the page administrator display Horizon shows an error window empty Horizon 7 ?

• Some Web pages do not allow (safari cannot connect to the server)

  I can't access some Web pages like the movie online, eBay, Amazon, etc. sites, when I try, I got the note as 'safari cannot connect to the server' and my chrome also got error like massage "this webpage is not available" more my App Store unable to work properly can not download updates»» I tried to delete all the data of the website... and uninstall extensions, but there was not work //I got a MacBook Pro 2014 middle with OS X EL capitan 10.11.2//some on help me please

  Please remove the 'ESET' product (if you have it installed) by following these instructions. If you have a different version of the product, the steps may be different.

  Back up all data before making any changes. Never install any product "anti-virus" or "anti-malware" again.

• App installed fish cactus, can you connect is no longer at the admin page

  Hi all

  I'm having a problem where after I installed app Cactus of fish I can no longer connect to my admin page. Previously, go to myaddress:80 would bring me to the admin page. Now only myaddress:80 / admin leads me to the admin page and it crashes until he tells me "ReadyNAS 'Admin Page' is in offline mode." I guess it's a problem with the apache configuration (the system uses apache, OK?) I have SSH access, so if anyone can point me in the right direction it would be much appreciated.

  Thank you

  L

  The fixed. There was a site called activated phantom fv-000-http causing trouble. I deleted it, restarted apache and now http://localhost/admin redirects to https://localhost/admin.

• WRT54G V8 cannot connect to the web-based configuration page?

  Earlier, I reset my router and was able to use 192.168.1.1 to visit the configuration page based on the web while trying to restore a home network, now that I have a new computer using Windows 7 that can not use the easylink advisor. I was able to get on the page update my SSID and WEP key. But when my wireless devices were still having problems to you connect to the internet, I tried to go back to the page and found that I can't seem to connect, even if my office is able to connect to other websites very well.

  Anyone know what I can do wrong? I use Verizon DSL. I was able to ping to the router and all tests have shown that it was connected fine, but I still can't get on the configuration page and my laptop can't connect to the network. I tried to reset the router again and still nothing. And Yes, I went through several cycles of power. I have also tried to move if the network card on my computer, but the computer said it was impossible to create a card for him, although at the time I had listed as a home network.

  Wireless on 192.168.1.1 connections often fail.  Using the router configuration pages, always use a computer that is connected to the WRT54G.

  If the above does not solve your problem, so here are my other tips to see the router configuration pages:

  You don't need an Internet connection. 'web Pages' of the router are integrated into the router.
  Use Internet Explorer, it usually works.
  JavaScript must be enabled.
  Use a computer that is connected to the router.
  In the non-working computer, temporarily disable your firewall software.

  Point your browser to 192.168.1.1, and then connect to your router. Your username must be left blank. Your password is "admin" (without the quotes), unless you changed it.

  If you use Zone Alarm, do a right-click on the ZA icon in the taskbar (bottom right of screen) then click on "Shutdown ZoneAlarm" and see if that solves your problem. If this does not work, try the following with Zone Alarm: open the control center ZAISS, go to privacy, then temporarily disable Ad Blocking and Cookie Control and see if it solves your problem.

  Some Zone Alarm users reported that the addition of 192.168.1.1 to their address list "of trust" solved the problem. This trick can also work with other firewalls.

  If you use Noton Internet Security with the add-on Pack, don't forget to disable the blocker and ad blocker. Some users have reported that they needed to uninstall all Norton Add-on Pack.

  If you can not get anything to 192.168.1.1 then perhaps this is not the address of the router. Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig" (with no quotes), and press the Enter key. Look at the "default gateway". It is 192.168.1.1? Point your browser to the 'default gateway', can connect you to your router.

  If the above fails, unplug your modem router, then try again. If it solves your problem, then you probably a "modem-router" rather than a regular modem. A report with this problem and also specify the brand and exact model of your modem (not router) number.

  If all above fails them, turn off your entire system, unplug it from the wall, wait a minute, then lights up, then try again.

  If all the above tips fail, then reset the default router: power down the router and unplug all the wires. Wait a minute. Switch on the router, let it fully boot (1-2 minutes), then press and hold the reset for 30 seconds button, then release the button and allow the router to reset and restart (2-3 minutes). Turn off the router. Wait a minute. To connect to a computer, cable, a router's LAN port. Initialize the system.  The router should work, but you will need to configure your router again from scratch.  If you have saved a router configuration file, DO NOT use it.

  If you still have problems, then you must download and install (or reinstall) the latest firmware for your router. After the update of the firmware, you must reset the default router, and then configure the router again from scratch. If you have saved a router configuration file, DO NOT use it.

• Cannot connect to the Configuration of iballBatonADSL2RouterModem page

  I have Win 7 Machine, to reconfigure my network security cannot connect to the Configuration of iballBatonADSL2RouterModem page

  Hello

  Thanks for posting the question in the Microsoft Community forums.

  Looks like you are unable to connect to the Modem router configuration page. Please answer a few questions to refine the question.

  1. what happens when you connect to the Setup page?

  2. do you receive any error messages?

  3. you try to configure for the first time?

  You can view the guide provided by the manufacturer of the router.

  http://www.iballbaton.com/download/118/IB-WRA150N%20User%20Guide.PDF

  If the problem persists, I suggest you to contact the manufacturer of the router.

  http://www.iballbaton.com/enquiry.aspx

  Hope this information helps. Get back to us if you have more queries about Windows.

• Cannot connect to my admin account and cannot change my standard user to the admin account

  I have 2 log ons, as administrator and the other is a standard user. Something happened that doesn't allow me to connect to the admin. Profile, but I can't the standard user and when I go to user accounts and you're trying to change that one to the admin. privileges, it doesn't let me change the account type. I recently purchashed Defender Pro 15 in 1 more all-inclusive anti-virus. Previously I was using Avira Antivir free House as my anti virus with no problems for a year or two, but then this happened if I installed the Defender but I can't access to half of what I need to do is no not Admin, any help would be greatly appreciated!

  Hello

  did you uninstall Avira before installing Defender Pro?

  2 aVs installed will cause blockages of the system or problems

  "Something happened that doesn't let me log on.

  and you don't give an error message on your admin account opening

  We need error messages to help you

  Uninstall Avira or:

  try a Safe Mode system restore to before this happened

  http://www.windowsvistauserguide.com/system_restore.htm

  If necessary do in safe mode

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• Cannot connect to the administrator account because the password is not valid

  Original title: I HAVE VISTA... ALL OF A SUDDEN FOR A DAY, I TRIED TO LOG INTO MY ADMIN PAGE AND MY PASSWORD IS NO LONGER VALID HOW TO RETURN TO THE PAGE OF MY ADMIN WITH ALL MY MUSIC PROGRAMS, ETC.?

  I tried to connect to my admin page and it will not allow my password... helllppp!

  Hi donfamous,
   
  Follow the steps listed in the article given below to resolve this issue:
  What to do if you forget your Windows password
   
  Additional reference on:
  The Windows password problems
   
  Note: Microsoft technical support engineers cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features.
  For more information, see:
  Microsoft's strategy concerning lost or forgotten passwords