Cannot load the batteries on the Satellite Pro a series

Similar Questions

• Cannot connect the Satellite Pro L series to TV

  Hello

  I have trouble displaying to an external source (LCD TV). There is no display when I connect to the TV. When I press Fn + F5 the only option available is the LCD cell phone IE. I checked on the driver settings and there is no option to select the parameters for a secondary/external monitor.

  Does anyone know what I need to do so that I can display to an external source?

  I use the connection of 15 pins with an adapter to convert video connection - is it ok or should I use the S-video connection on the back of my laptop?

  Any help would be appreciated

  Hello

  This TV option does not appear because you have connected the TV to the wrong place.
  The TV device must be connected to the laptop s-video port via compatible and s-video cable supported!

  Then, you can use FN + F5 to switch the display to the TV set.
  Please note: sometimes the s-video channel must be enabled on the TV!

• Cannot start the Satellite Pro A120SE-180

  Support the necessary computer startup.

  I have a Satellite Pro A120SE-180. I took out the RAM to check how much I had. Then, I opened the battery compartment without thinking about the consequences. Now I get just a power indicator and that it will not start at all.

  I can't open the disk drive or get any life out of it. I was running an upgrade of Vista, which was available as a cheap option when I bought with Windows XP.

  Hi Rob,

  What might have happened, is that the operating system and a hard drive can have erased himself when the RAM and battery have been removed at the same time!

  The only way to fix and doing things is again to send it to a Toshiba service center and get them to look! Also, do not upgrade to Vista - I'm using XP and it seems to do the job the way it was supposed to! I intend to switch to another Satellite Pro, an A300 running Vista, but I will look for someone who can replace XP on it!

  Joe

• Macromedia projector video is distorted on the Satellite Pro L series

  Hello

  I have problems running a file of projection of Macromedia.
  It works but the video is distorted.
  If I remove the 965 chipset drivers, it works fine.

  But of course, it's not ideal because it causes problems with switching between the projector and the screen of the monitor.

  I tried to find more drivers today ect but same problem occurs.
  There's nothing wrong with the presentation that it works well on any cell outside.

  Any ideas?

  Hello

  Perhaps the graphic card driver should be updated I come to the conclusion that it is a problem of compatibility between the graphics driver and Macromedia projector, due to the fact that the video works properly after uninstalling.

  Then why you n t visit the Intel page and download the latest graphic driver for 965 chipset.

  By the way; computer laptop Satellite Pro L do you have?

• The Touchpad right button does not work on the Satellite Pro L series

  The icon in the taskbar indicates that the right button is permanently pressed, if it is not.
  So I can't right click at all. A radio mouse works fine, but there are times I want to use the touchpad.

  In addition, the screen does not turn off, and the computer goes to sleep after the hours set in the options of energy saving.
  I listen to the radio a lot and do not want to display on.

  > The icon on the task bar shows that the right button is permanently pressed, if it is not.
  > So I can't right click at all. A radio mouse works fine, but there are times I want to use the touchpad.

  This could be linked to defective button. If you cannot use the right button, and the button appears to be clicked down, then I suppose that its hardware malfunction.
  In this case it must be replaced.

  > In addition, the screen does not turn off, and the computer goes to sleep after the hours set in the options of energy saving. I listen to the radio a lot, and don t want the display on.

  Have you chosen the right power Plan? In Control Panel-> power options you have to choose the diet plan and should click: change plan settings. Here, you can change the time when the display must be disabled.
  If this does not work, then I guess that this feature does not work because you press the button of the touchpad and the windows OS think that the notebook is in use

• Gray pixels below the back of the screen onto the Satellite Pro U series

  Hello.

  After a month since the laptop purchase date, I had a problem with my screen (a black point aprox. 1 mm size - not dead pixels but something like a bug between plans display, perhaps between the trubright and the lcd screen, whatever it is these plans I don't know not-on the side rear of the screen, on the lower part), solved by Toshiba customer service using the replacement of the screen.

  But, after one more month for the replacement, the problem was once again with some minor differences.

  My screen looks like now, on the lower part of the screen (about 1-3 cm of the bottom line) a few other gray (this time) points, each with approximately 5-15 pixels of size.

  I counted to date a total of four quite visible like these bugs and a few others having no importance because of very small size, on the different areas of the screen.

  I am concerned because it seems these gray he appeared on time, more points. What mean these bugs and what solution is there?

  I want to know your guys, if anyone has a similar problem, what the problem actually is and how you can permanently solve.
  (I can not simple running again for the service because I guess I'll do every month)

  Thank you
  Iulian

  PS: Please do not ask me how to clean it's screen. It is not my bugs he and the monitor (first surface I mean) have some some dirts. I'm very cautious in this regard.

  Hello

  We could speculate about this problem, what might be wrong; Map chart or screen itself?  :| ?
  I think it s a default display

  > I want to know your guys, if anyone has a similar problem, that the root of the problem is and how you can fix it permanently.
  Personally, I've never noticed these display problems on my laptop satellite.
  I think it is foolish to discuss on the reasons why this happens it looks like simply a hardware problem. You ask how do I solve this problem?
  In my opinion there is only on the solution; replacement screen.

  Contact the ASP guy and ask for later handling.

  Concerning

• Intel GMA graphics driver update on the Satellite Pro U series

  I want to upgrade my graphics accelerator driver that is Mobile Intel 4 Series Express Chipset Family.
  On the Intel website, I found this accelerator and new driver for Win XP OS that has been released 31.3.2009, its version is 14.38.3.5047.

  Although I can not install it because this driver is not verified by Toshiba and the site Web of Toshiba is the driver who is one (of course I have it) year old. So, is a way to install the new driver from Intel or can you please this verified driver?

  BTW, if the latest drivers are more than a year, it does not resemble the good support.

  Zdenek Konecny

  Hello

  I m using Intel drivers too and I n t have a problem to install.

  If you have tried to install the driver through setup.exe, you should try manual in Device Manager. Right-click on the graphic card > driver update. Use the Advanced installation step and choose the driver directory yourself.

  Before installing the driver, you must remove the older version first, and then restart the laptop.

  Good bye

• TOSHIBA Power Saver of the Satellite Pro M series stopped working. (code 0 x 0)

  The utility has suddenly stopped working after Windows XP update.
  Informed, that there was an irreparable failure and performance of the program will be interrupted.
  Code 0 x 0

  What should do?

  Hello

  Maybe you should download the new version of the powersaver to your machine, remove the old version (go to Add/Remove Applications in your 'control panel' and uninstall) and install the downloaded one.

  You can download the powersaver here:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  Good luck
  Welcome them

• Satellite A30: Error number (11122) cannot load the bitmap with recovery CD

  I have a Toshiba A30 I want to reformat with the recovery disk. I get that day then I get an error that reads:

  The error number (11122) cannot load the bitmap file. Height max = 100

  The hard drive has now been deleted and I can't sent this message to reformat.

  Can someone help me on this please.

  Hello

  Satellite A30 is quite old and I wonder what report you something like this after so long. I put t know exactly what is happening, but it will be interesting to know a few things:

  Have you noticed a similar problem before?
  Are you using the original disk or some copy?
  Is there a problem with the HARD drive?

  Please do a little bit more about these things.

• Satellite A200 - cannot load the keyboard and touchpad drivers

  Hello

  I have SATELLITE A200-10W, HOME PREMIUM installed with SP1. I use it more than a year. All of a sudden it happened that my laptop stop responding and then I rebooted.
  My touchpad and keyboard stop working, but I connect as a user of the window through KEYBOARD to the SCREEN.
  In Device Manager I CAUTION icon on the keyboard and inside, it says under DEVICE STATUS which

  Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (CODE 39). »

  i8042prt.sys and kbdclass.sys files are attached as a driver in detail.

  My keyboard works during BIOS and even when I boot with the CD bootable operating system WINPE, my keyboard is not working, even typing everything inside this environment, but not in the normal window.

  I tired restore my laptop
  LAST GOOD CONFIGURATION
  Apply unsigned drivers
  Safe MODE (does not work yet)

  Downloaded some software like driver detected etc, but... NO RESULTS.

  I don't want to go for WINDOW RECOVERY CD for OS to re - install
  I have a large number of parameters, I don't want to erase...

  IS THERE A SOLUTION FOR IT?

  My warranty ended already after one year

  pls help and answer...

  That s a great info. Thanks for the clarification!

  Good bye

• Cannot get the printer driver to install the Satellite Pro C660

  tried to install epson rx560 driver printer (windows 7 64-bit) the satellite pro c660 but it fails epson told me to consult a technician because the printer driver is very good

  Any help would be welcome

  I don t think that it is a mobile phone number.
  In my opinion, you should visit and check the Epson support page:
  http://www.Epson.co.UK/printers-and-all-in-ones/inkjet/Epson-Stylus-Photo-RX560/drivers-support

• Intel Pro/Wireless 3945ABG cannot load the driver

  Wireless worked fine since I bought this laptop

  Now it has stopped working and has a yellow exclamation mark in Device Manager - it says "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  So I uninstalled the device and check the box that says "Remove the driver for this device", then reinstalled the latest version of the driver on the Toshiba site 11.5.0.32.

  Windows Vista detects new hardware and install the driver, but fails with 'Windows found driver software for your device but encountered an error trying to install it. The system cannot find the file specified. "

  All ideas

  Remove the wireless network adapter in the device, download manager driver the latest from Intel page and repeat the procedure of installation of the driver.

  Good luck

• Help identify the Satellite Pro 2100 download driver

  I have a Satellite Pro (marked below as a PS210E-00C3G-EN and a P4 2000/256/30 G, 15XT, CDW, LW). I think it's a satellite Pro 2100, whatever.

  Problem I have is that when it comes to downloading the drivers, I can't find anything approaching this model of the selection process. I've searched the forums and there's not much on this machine otherwise than in this one, so I was hoping someone could help me identify this machine especially for driver downloads... Yes, guess who has reinstalled Windows XP without checking I had all the specific stuff Toshiba tucked away first?

  For now, I have a load of things works without drivers, and it is not at all optimal...

  Thanks in advance

  J

  Toshiba European driver on this page;
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU#

  and choose;

  The Satellite Pro Archive Satellite Pro Satellite Pro 2100 21xx archives *.

  Then you will find all drivers available for this machine Toshiba ;)

  Good bye

• Registry cannot load the HIVE file; Need to fix WITHOUT the Recovery Console, computer will not play my Windows recovery disk.

  I need to fix my computer, I got the blue screen of death with the following error message. Registry cannot load the file \systemRoot\system32\config\SOFTWARE "HIVE".

  I read all the forums on how to solve this problem. I tried all the means which have been enumerated. None have worked so far because I can't get my CD player to load to run my Windows XP Pro disc to start the repair.

  Is there a way to fix this without the disc. I can't the computer after Windows XP display until he went blue. It's a computer original systemax, but I have since rebuilt it me with the new motherboard, hard disk, cdrom, dvdrom, ram, fans, cpu, etc... I just got a new monitor and hung up and blue screen of death appeared after that I turned the computer back on. I tried to fix this for 4 days now. Someone please HELP me.

  I got it fixed. THANK YOU SO MUCH for all your help!

• C0000218 {registry file failure} the regestry cannot load the hive (file)

  I have XP pro. on a Dell computer. Think that children may have picked up a few difficulties. When trying to boot into safe mode, I get "Stop: c0000218 {Registry file honor} the regestry cannot load the hive (file): \SystemRoot\System32\Config\Software or its log or replacing." It is damaged, missing, or not accessible in writing. »

  There is no disk that came with it, but I have anouther computer with the same windows. I tried to find a way to make a BOOT disk but cannot find a way. Is there a way to solve this problem with the windows disc?

  It's a pretty popular mistake these days and sometimes easy to get running, but you also want to figure out how it happened.  I always suspect Symantec/Norton products with this error, but we'll see.

  If you currently or have already had a whole isntalled Symantec/Norton products, what are the names and versions (if you know).

  Other variants are:

  STOP: c0000218 {Registry file failure}
  The registry cannot load the hive (file): \SystemRoot\System32\Config\SECURITY or its log or replacing. It is damaged, missing, or not accessible in writing.

  STOP: c0000218 {Registry file failure}
  The registry cannot load the hive (file): \SystemRoot\System32\Config\SOFTWARE or its log or replacing. It is damaged, missing, or not accessible in writing.

  STOP: c0000218 {Registry file failure}
  The registry cannot load the hive (file): \SystemRoot\System32\Config\SYSTEM or its log or replacing. It is damaged, missing, or not accessible in writing.

  I would start with a chkdsk/r since the recovery CD of Console you make (see below) and please answer a few questions...

  Maybe someday the dialog box 'ask a question' forums XP will ask these questions automatically when a new thread is started so I don't have to ask every time.  It might even be possible to solve a problem in a single response when enough information is provided.

  Please provide additional information on your system:

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a CD/DVD drive work?

  You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?

  Fill in the blank: my system was working fine until this happened: _.

  If the system works, what do you think might have changed since the last time it did not work properly?

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that may have come to a store to purchase the system.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

  Do, or do not. There is no test.

  I decided to implement the points for a new puppy instead of a pony!