Cannot start after WinXP disk Image resizing

Similar Questions

• Mac cannot start after el captain

  Cannot start after updating mac

  Safe Mode boot removes the system caches that can help after an OS X day or level.

  Follow these steps to start in safe mode.

  1. Start or restart your Mac.
  2. As soon as you hear the startup tone, hold down the SHIFT key.
  3. Release the SHIFT key when you see the logo Apple appears on the screen.

  After the Apple logo appears, this may take longer than usual to reach the login screen or your office. This is because your Mac performs a check of directory of your drive to boot in safe mode.

  To leave safe mode, restart your computer without pressing any keys during startup.

  Try safe mode if your Mac does not end commissioning

• Cannot start after the blue screen "page in the nonpaged area failure."

  My sons laptop has got to me.  There the error page blue to come with "failure page in the nonpaged area." There is a chain of technical info of numbers, but this changes a little at each attempt.

  I tried all F8 options, without success.  I did a restore disk from the laptop of my other son (which is the same) and that has not worked and I also downloaded a file of system restore on the internet who do not.  I ran diagnostics memory on the scope option and who found nothing.

  No matter what I try, always the fails to start after the first screen with Microsoft Corporation at the bottom and the small lights of scrolling!

  I would be grateful for any suggestions that anyone can have.  I wondered if I should try to borrow a disc of Windows Vista from someone and try from there?

  Read the messages and follow the procedures established by the MVP of the spirit in the following thread on the Blue Screen of Death.  They should help you solve your problem. http://social.answers.microsoft.com/Forums/en-US/vistahardware/thread/8cd8362e-7d06-46fb-afd7-84d54b6a8ea7.

  I hope this helps.

  Good luck! Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Code 10 device cannot start after Windows update.

  Original title: had this application update 26509 operation message

  I hope that I chose the right place for this question

  By PAD so I give you all the unusual things that have occurrred recently

  When I clicked shut off (to turn off the computer) last night I received a message something like this but this isn't verbaitim.

  -apply the updates do not turn off or disable... Let him go was not a thing then it shuts

  This morning from my computer (windows 7) I see a lot of numbers flight by update of something... Finally he stayed still long enough to read this message

  ' application operation update 26509 26509 (\Registry\Mach...) . who took about 90 dry

  then the screen changed to say prepare to set up windows (while I was getting a large piece of paper to write it down in my computer I went back to what is normal for my computer open) he says treatment auto - VGA - the screen is black for 2 seconds and my office is open and functional.

  --------

  Please lmk if I should post this separately if it is not part of the above problem

  OK not to confuse things and maybe it's not bad but I will also attach additional information... Thank you for your patience.

  Sometimes messages arrive on my screen and went so fast that I don't know what they said and that's what's happening all I saw were collected WAN miniport (ATW) #2. and something that affects the usuage of my computer... I went to the Device Manager and under "Network card" was a green line to see, I opened 2 inputs was the first

  "Intel (R) 82578 DC Gigabite Network Connection" under properties it says that this device does not work correctly

  the second entry "WAN Miniport (ATW) #2 * was a yellow triangle with a point of exclamation and under properties say this device cannot start (Code 10) .

  I'll wait on this case its not important right now with my orogonal above problem

  Thanks again for you time and patience... looking forward to your entry

  Learning to 62 (aka granny)

  Hello

  1. have you successfully install the update?

  2. are you able to connect to the desktop without any problem?

  Was the message you saw before Windows starts, the system applying these updates. This is a normal procedure that Windows takes above all the critical updates are applied. If you were not able to start Windows, then we might have a problem with Windows update.

  Regarding your second yellow exclamation on the wide area network WAN miniport, you need to update the driver for the network adapter.

  The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues. You may need to update the chipset drivers and the network adapter.

  I suggest you run the automated FIXIT from the link below and.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  I would say as update you the driver for network card and check.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• C855-1VT satellite - cannot start media recovery disk

  Hello

  I have the laptop above that was dumped on its edge causing the hard drive to the jam and fail.
  This means no access to the system recovery, so I ordered arvato shop Toshibas Recovery Media recovery media.

  I installed a new HARD drive has slipped into the recovery disc and boom, no bootable media insert system disk.

  I tried the disc on other laptops, same thing, with no bootable media, but back to arvato who kindly sent me disks replacement... you guessed it... exactly the same thing so I put in my windows 7 install cd and it read the disc properly.

  Arvato said they asked toshiba to check the image which they did and found no errors, but the stock of arvato could be faulty, I thought. in any case, they offered a refund which doesn't really help.

  I may be missing something so this post hoping tosh guru of you might be able to help :)

  Thanks in advance,

  Night...

  Hello

  Maybe the image is OK, but the CD/DVD drive cannot read the disc of Arvato.
  What you could do is to copy this recovery disk to another disk using another computer.
  Then you could try to start the device using the new disc copied.
  May be worth a try.

  In addition, you can try after workaround:
  Go to BIOS and check secure boot settings and the boot mode.
  What are the settings appear in the BIOS?

  I m application because you said you could boot from Win 7 disk, in this case secure boot must be disabled and the boot mode must be set between UEFI and MSC mode.

  In case you want to install Win 8 secure boot must be enabled a UEFI should be used

• Cannot start after the formatted NTFS partition

  Option to boot OS X suddenly absent after that I formatted the partition NTFS (bootcamp) of Windows installation.

  

  I read many previous question in many Web site and

  I tried to fix it in disk utility, but it cannot go up more.

  user mode single launch I tried, but it does not start.

  already reset NVRAM and SMC.

  Is there not any solution to start again or access my files in the partition mac to back up?

  Thank you.

  Somehow, you managed to format your OS X with making it unusable NTFS volume. I recommend you do the following:

  Clean Install of El Capitan

  Restart the computer. Immediately after the chime, press Command + Option + R until a globe appears.

  The Utility Menu appears in 5 to 20 minutes. Be patient.

  Select disk utility, then click on the continue button.

  When loading disk utility, select the drive (generally, the entry Out-bumpy) in the list aside.

  Click the Partition tab in the main window of disk utility. A panel will fall.

  Set the GUID partition scheme.

  Define the type of Format Mac OS extended (journaled).

  Click on the apply button, then click the fact when it is active.

  Quit disk utility and re-enter the Utility Menu.

  Select reinstall OS X and click on the continue button.

  This should install it the version of Mac OS X that has been previously installed when the computer was new.

• Windows does not start after the MAC partition resize

  Hi all

  I am newbie in MAC OS.

  I have 2 bootable partitions on my MBP: MAC 10.11.4 Capitan and WINDOWS 10.

  What I have is:

  1. install MAC OS in the DSS of any origin.

  2. use bootcamp, divide the similar size for WINDOWS 10.

  3. install the new fresh WINDOWS 10 correctly and updated. Yet to backup. None of the additional applications. WINDOWS is default OS.

  4. so far, I need MAC OS or WINDOWS OS correctly. Yet to backup.

  5. I need to resize smaller MAC OS, divide into partitions of DATA for data could leave the two BONES.

  6. Since then, I can't start Windows. Doesn't appear that "no device bootable bra bra bra...»

  7 but if I click on Option after turning on, I still see MAC OS option.

  Could help me fix bootcamp, so I can have the WINDOWS startup and the DATA partition?

  Thanks a lot before.

  diskutil list

  Cs diskutil list

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

  The result of the Terminal:

  GEORGEs-MacBook-Pro: ~ the georgeaprianto list $ diskutil

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * TB 2.0 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage MAC 502.4 GB disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database DATA 497.0 GB disk0s4

  5: Microsoft WINDOWS 1000.0 GB disk0s5 data base

  / dev/disk1 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS MAC + 502,0 disk1 GB

  Logical volume on disk0s2

  8256E61A-9B5E-436A-8A15-97A98A55E0E3

  Unencrypted

  GEORGEs-MacBook-Pro: ~ list of cs georgeaprianto$ diskutil

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group 7C0ED763-7739-42D4-85DB-E84BD98FA978

  =========================================================

  Name: MAC

  Status: online

  Dimensions: 502414561280 B (502,4 GB)

  Free space: 18907136 B (18.9 MB)

  |

  +-Physical volume EEF7EECD-2732-4794-8ACC-B1FDBE3FFFAE

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 502414561280 B (502,4 GB)

  |

  +--> Logical volume family 821E2FC7-4169-4452-BC6D-7469364950F4

  ----------------------------------------------------------

  Encryption type: no

  |

  +--> Logical volume 8256E61A-9B5E-436A-8A15-97A98A55E0E3

  ---------------------------------------------------

  Disc: disk1

  Status: online

  Size (Total): 502043332608 B (502,0 GB)

  Reversible: Yes (no required decryption)

  Name: MAC

  Volume name: MAC

  Content indicator: Apple_HFS

  GEORGEs-MacBook-Pro: ~ georgeaprianto$ sudo TPG - vv - r show/dev/disk0

  Password:

  See the TPG: / dev/disk0: mediasize = 2000398934016; SectorSize = 512; blocks = 3907029168

  See the TPG: / dev/disk0: MBR suspicious to sector 0

  See the TPG: / dev/disk0: Pri GPT to sector 1

  See the TPG: / dev/disk0: GPT Sec at sector 3907029167

  start index size summary

  0           1         MBR

  1 1 Pri GPT header

  2 32 table GPT Pri

  34 6

  40 409600 1 part TPG - C12A7328-F81F-11D2-BA4B-00A0C93EC93B

  409640 981278440 2 part TPG - 53746F72-6167-11AA-AA11-00306543ECAC

  981688080 1269536 3 part TPG - 426F6F74-0000-11AA-AA11-00306543ECAC

  982957616 970684880 4 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  1953642496 262144

  1953904640 1953124352 5 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  3907028992 143

  3907029135 32 table dry GPT

  3907029167 1 dry GPT header

  GEORGEs-MacBook-Pro: ~ georgeaprianto$ sudo fdisk/dev/disk0

  Disk: geometry / dev/disk0: 243201/255/63 [3907029168 sectors]

  Signature: 0xAA55

  From end

  #: cyl hd s - cyl hd s id [Start - size]

  ------------------------------------------------------------------------

  1: EA 1023 254 63 - 1023 254 63 [1-409639] < unknown ID >

  2: AC 1023 254 63 - 1023 254 63 [409640-981278440] < unknown ID >

  3: AB 1023 254 63 - 1023 254 63 Boot Darwin [981688080-1269536]

  4: 0 b 1023 254 63-1023 254 63 [982957616-970684880] Win95 FAT-32

  GEORGEs-MacBook-Pro: ~ georgeaprianto$

• How to rename ASM starts after cloning disks of origin on the same server. ASMlib is used

  RHE Linux 6

  The single-instance grid installed Oracle (Oracle Restart) 11.2.0.4

  Oracle RDBMS 11.2.0.4 installed

  A 11.2.0.4 single-instance database running

  Our ASM GAVE, REDO, FRA mounted diskgroup

  We need to do a snapshot of storage for the creation of a copy of the current start ASM DATA, REDO, FRA on THE SAME server. Then we rename it cloned starts using the renamedg command.

  We did this several times if ASMlib is not used. For example, the command used when ASMlib is not used is:

  renamedg = newdgname = verbose = FRA2 FRA dgname true phase = the two asm_diskstring = "/ dev/oracle/fra *'"

  With ASMlib in use, I'm not sure the steps to follow

  First of all I'm not sure what should be provided to the asm_diskstring for the renamedg command parameter. I provide an asm_diskstring that identifies the path pointing to records belonging to the diskgroup cloned (I don't want to rename the original diskgroup). But ASM instance using ASMlib is the asm_diskstring parameter is in ' ORCL: *'.

  Second, I guess that after the rename diskgroup than asmlib returns an error because she would double discs.

  Could you please tell?

  Thanks in advance

  Massi

  Hello

  As you clone OS level, you have same ASMlib label.

  ASMlib mount always unique ASMLib label only.

  + You must identify these newly cloned device.

  + Rename these ASMLib force-renamedisk label after 1 Mb disk backup using dd read on a node.

  + Then run scandisks on other nodes.

  + Validate newly approved device is mounted or not on all nodes.

  $ ls - ltr/oracleasm/dev/discs / *.

  + Run command with asm_diskstring of/dev/discs/oracleasm renamedg / *.

  Kind regards

  Loriette

• Portege 2000 cannot start after suspend

  Hi guru,.

  I'm new to this forum. So I looked through the first forum hoping to get an answer to my problem before posting, but no good result.

  Here's my problem. My portege 2000 works before brilliantly. But last night, while I was trying to configure my APM suspend (this is the first attempt to suspend), the problem, the system freezes! Then I tried to restart, can not remember I turn it off by pressing the button for a few seconds or unplug the hand because of the power key is not, in any case I have wait a few seconds after that, then turn on the power again, but the system seems to be dead, the AC power led is under voltage green LED, battery was not in the slot so no sign for her, the small button Fn LED told me this Fn key works well, but the caplock key does not work because its LED is not turn on after pressing, the screen is blank, or should say it is not powered on, the hard drive does not turn.

  So I unloaded the system by unplugging it from the main. After a while I swhitch on once again, the laptop is still in the same situation. Therefore, I tried to unload everything, disconnect the hand, open up the laptop, unplug the CMOS battery, wait for a while (15-20 minutes), then put it back on, but no joy.

  I did some research on Google at this time and read the knowledge base on the web site of Toshiba, seems the problem come with BIOS, who say that the system does not start if the power is off during suspend mode for the original version of BIOS (later healed). So, I decide to Flash a BIOS to most recent version. I have a pc card floppy drive, so I download the BIOS and create the floppy, then I use the key to update the BIOS to power on the laptop, luckily this time it works, "ready to update bios" screen appear. But when I press the key on the keyboard, it seems that it does not access the pc card floppy drive.

  By this incident, I think that the material has no problem, but the system is in standby for ever. Guru of the idea?

  Therefore, I have 2 questions:
  1. how to make it back to the start mode so that I can start my system? I need this as well according to the Readme of the BIOS update package, it should be in start mode, no interruption/recovery mode.
  2. how flashing a new bios in this situation? Do I need a USB floppy drive to do the BIOS to recognize that there is a drive so that I can Flash a new bios in there? Or the system will analyze not for material in this mode 'freezes '?

  Sorry about the long story, but I think I must tell him that you guys understand the situation and what I've tried so far.

  Additional information on my system, I'm under debian linux etch on this laptop, and everything that happened after I typed the command "apm-s". But it seems to me that it is the problem of BIOS problem OS?

  Thanks in advance.

  concerning
  Colin

  Hello

  First question: How did you install the operating system if the laptop will not start?

  I'm a bit confused Mr. I put t you know what means the boot mode.

  If the laptop has been completely stopped down so it s in the boot mode (standby or hibernation mode don t mix).
  If you want to update BIOS please make sure the BIOS is good and that you use the right update procedure.

  Where did you find the information that the BIOS update will solve this problem?
  In any case, for me, it looks more like an electrical problem on the motherboard.

• Satellite A30 cannot start after cleaning the heatsink

  I have a problem with my sat a30. It lights for 5 seconds then goes automatically off and on again for 5 times, before finally shutting down completely. all this began after I cleaned the heatsink. can you give me some advice for what to do with this problem?

  Hello

  This path is not easy to say what is the problem, because, who know what did you exactly and how. As you know do something like that on your own is always risky.

  Are there signs of life of the cooling fan? AFAIK the CPU becomes very hot in just seconds after the start, and I presume that CPU is not cooled properly and because of this unit turns off.

• a1720n cannot start after the installation of the DVD from LG GGC-H20L drive

  I installed the unit and connected to the second channel SATA (blue) and the computer would not start.  Disconnected and the system returns to normal operation.  It appeared that the system was able to read a correct reader type in the BIOS.  I couldn't find any instructions online documentation SATA configuration.  I will apprecaite the ideas or the BTDT there!  Thansks!

  Thanks for your quick responses!  I advanced and tried to just connect the drive again and the system booted properly.

  When I said that the system does not boot, it would go beyond the BIOS screen but should restart after trying toload windows.  Subsequently an any a GUI recovery came, ather than aloowing system to restore from an earlier time, I told him to try an automatic recovery.  This process was then several minutes before failing.

• Win7 (Home Premium) cannot start after "important update"

  I just bought a new PC with Windows 7 Home Premium pre-installed. After an update that Win7 launch is no longer, instead the PC reboots from the BIOS. Now, as I write to you from my old XP system, I do that I can't do this post shouldn't indicate that I found a solution. Using the utilities available / suggested at this stage, I can't understand what the 'important' update was so am not able to retrace the steps that may have caused problems. Currently, I run the system recovery, so maybe in a few minutes, I might be able to use the WIN7 PC again. However, I would like to know if anyone else is / has been faced with this problem.

  Hi isamart,

  First of all, I suggest to start the computer in safe mode and see if you can boot to the desktop.

  To boot to the desktop in safe mode keep tapping key F8 during restart. Once you see the option to start in safe mode select and press to enter.

  Access the link to learn more about how to start the computer in safe mode: http://windows.microsoft.com/en-US/windows7/Start-your-computer-in-safe-mode

  If you are able to access safe mode, you can try to check the update installed on your computer and remove it and check if that helps.

  To view and remove the updates installed, follow the steps below.

  1. click on start

  2. in the start search box type appwiz.cpl, and then on enter.

  1. click on view the updates installed in the left pane.

  2. take note of the recently installed update in the list and remove the update.

  3. restart the computer and check if you can start.

  If the steps above fail, you try to perform a system restore on your computer to an earlier date and check if you can boot to the desktop.

  To restore the operating system to an earlier point in time, follow these steps:

  1. Click Start, type system restore in the search box, and then click System Restore in the list programs.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  2. in the System Restore dialog box, click on choose a different restore point and then click Next.

  3. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  4. click on finish.

  The computer restarts and system files and settings are back to the State they were in when the restore point was created.

  Access the link below to find more information about the system restore.

  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  I hope this helps. Let us know the result.

  Thank you and best regards,

  Srinivas R Microsoft Support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Aspire E3 - 112 cannot start after win10 own attempt installed

  The installation is wrong. He went right through the extract process and install OK but then just went along in a loop to keep reinstalling the usb drive. I changed the bios by promoting usb hdd over windows Boot Manager (in uefi). So I removed the USB drive and restored the order of the bios. But now, when I boot, I get an error window saying "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install windows click OK to restart the computer, and then restart the installation. "It makes no difference if I close the window or click OK, it goes through the same circle.

  Help!

  Thanks for the reply. I tried that. In the end, I found that the solution was to wait for the beginning of the (umpteenth) reinstall the process and then press the power button for a few seconds until the machine stops. Then I powered up while pressing the F2 and is gone in the bios where I restored the original and the machine parameters and then started in the new clean install.

  Unless the OS is nuked, how to perform a clean install is using the settings > update & security > Recovery > restart now and use the boot from usb option. And leave the bios alone.

• HP Pavilion DV4-1125nr cannot start after the update/update BIOS version F.12 to d.55

  System: HP Pavilion DV4-1125nr PC Notebook

  Product #: FR922UAR #AB

  The system board ID: 30F7

  Version of the BIOS (before the update): F.12

  OS: Windows 7
  

  I tried to update the BIOS to d.55 which was provided by HP. After the successful installation the closure of new windows BIOS correctly. I restart the PC, HP Logo appears and then nothing happens. The operating system do not load or start at all.

  I also tried to boot using the Windows 98 Second edition CD (to charge BACK), but it did not work.

  Please help me...

  Fortunately I found a Solution to this problem.

  Here are the summaries (and modified according to my needs) the steps that I've taken of the following thread:

  http://h30434.www3.HP.com/T5/notebook-hardware/dv4-1140GO-won-t-boot-after-flashing-latest-BIOS/m-p/19698#M2730

  1. go to the hp site and download the correct version of your BIOS. In my case it had to F.12. Why not the latest version? Because there is no guarantee that the last one will work for you, know after measures.

  2. go where you downloaded the file and using 7 - Zip (or tool of your choice of course) unzip the contents to a folder of your choice. We'll get to that later, so keep this file open.

  3. use 128 MB or no matter what key-USB USB key (the smallest, you might find, because they said the smaller the better ) and reformatted to FAT or FAT32 click with the right button on the drive by clicking on "format".

  4. now that my USB is ready, go back to the folder where you extracted the file to update the BIOS (always open to the right of the folder?)

  "5. If you have the graphics card Intel integrated like me, copy the ' 30F7F12U. FD"of the key USB and RENAME the file '30F7F12U. FD' at '30F7. BIN ". Remember that this name calling to order "DV4-1125nr. If you have a different motherboard, the system or the BIOS, the name must be determined according to the.

  The next steps are exact 0.0 as follows (the link of a full detailed discussion is provided below), I simply numbered:

  6 unplug the adapter from the laptop.

  7 remove the battery from the laptop.

  8 insert the USB key into one of the USB ports on the laptop.
  Does not seem to matter which.

  9. press the 'Windows' key and the 'B' key

  10. connected to the power adapter.

  11 press the 'Power' button on the laptop.

  12. when the LED is entered, letting go of the power button / stop and the two keys down earlier.

  13. After about 10 seconds the notebook started to read the USB key. While searching for the file, the laptop beeps every seconds.
  The number of beeps varied, depending on what size of the key USB has been and
  the number of files on the USB key, a single beep for many.
  If the file was not found, the laptop will restart and try again.

  14. If the file is found then it took about 12 seconds for the laptop to load. No beeps sound not heard during the loading time.

  15. when it is responsible for the laptop has started flashing, indicated by beeps every 2 seconds. It took about 32 seconds.

  16. about 5 seconds after the ringtone had stopped off the laptop computer.

  First I update my pc with the last BIOS (F.66), but did not work for me (operating system not loaded after HP Logo ). So I decided to go back to the old F.12 (the version that has been shipped when the laptop was purchased) according to the procedure described above. But the problem is where to find version F.12 as HP currently provides links only for the version of the BIOS F.66 to d.55 (in the drivers from the hp support site section)

  Fortunately, I found a direct link to this version F.12 in the next thread.

  http://Forum.NotebookReview.com/HP-Compaq/304332-C700-CQ40-CQ45-dv4-dv5-DV6-hdx18t-Insyde-BIOS-recovery-using-USB-thumbdrive-2.html

  F.12 version:

  FTP://ftp.HP.com/pub/SoftPaq/sp40501-41000/sp40749.exe

  This was F.12 and worked for me. Thank God Almighty I return my PC.

  Thanks to all who contributed in the discussions above.

  Kind regards

  -gmuhammad.

  If you think that this post has helped you, then please give KUDOS *.

  Close the thread (Accept as Solution), if your problem is solved *.

• Cannot start with any disk

  Hi all,

  Could someone help me because this problem is crazy drivinme!

  They gave me a pc less hard drive, disk and dvd - so I therefore sat last night and put put in a fresh new hard drive and a new drive, then I was ready to go and put XP home on.

  This is a not to do as he would entangled initialize not he manages to come up with either Grub error 17 or 22 so I double checked all settings of the bios as so far, I'm aware that I don't think I missed something... so I tried to start with - 3 other drives xp, ubcd4win, and a startup disc patition magic - and guess that soon one start you the pc it reach not to start and stay on the screen with loading GRUB error 22 Please wait please help!...

  Concerning

  GT4U

  Hi all,

  This problem was a simple solution using startup disk wizard patition and rebuild the M.B.R - master boot record.

  Concerning

  GT4U