Cannot trace to the hosts on the international research reports using FW feature set

Similar Questions

• Cannot run chkdsk - Chkdsk cannot run because the volume is in use by another process.

  original title: can I run chkdsk on win xp home, but when I try to use switches, I get cannot lock the current drive. Chkdsk cannot run because the volume is in use by another process. HELP PLEASE

  I run chkdsk without switches on win xp home. I told myself I file error and to set running chkdsk with /f. but when I try, I get the cannot lock the drive, chkdsk may not run because ect...  I tried in safe mode, same thing. I sfc/scannow, but it has not fixed the problem files. help please

  It's normal.  You can not run a check disk on your system disk because your system is to use.  The Message you get should ask you if you want to run it at the next reboot.  You must answer 'Yes' to this message, and then restart your computer.  A disk check should take place as it is restarted.

  FYI: A check disk can take hours if you have a large drive or there are a lot of problems on the disc and you cannot use your machine while the scan is in progress.  Better to operate during the night.  Also, I got checkdsk completely erase the hard disk to the point where the only option was to reformat and reinstall Windows.  Make sure that your data available are well-supported before running Chkdsk.

  "How to perform disk error in Windows XP check"
    <>http://support.Microsoft.com/kb/315265 >

  HTH,
  JW

• Chkdsk cannot run because the volume is in use by another process

  My computer was working fine until last night. Now when I connect I get a blue screen saying that the computer shuts down to prevent further damage from happening. I tried to restore to an earlier point in time when my computer was working but then I get the error:

  The OS disk (C :) has errors.
  Windows has detected corruption on OS (C :) file system. You should check the drive for errors before you can restore it.

  So I'm going to run the chkdsk utility, and I get the error:
  Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time the system restarts.

  I'm confused because the chkdsk unility usually works, and I have no idea why she is being used by another process. I am clearly not very good with computers. I tend to do a lot of spywear and adwear on my computer. I have Spyware Doctor that removes any infection.

  Help, please. I've tried everything. Thank you.

  Asha22,
  It appears from your last post why chkdsk did not run on reboot and you gave an incorrect message is that you did not a space between the volume and the f number.  The correct syntax is:

  CHKDSK c: /f

  You can also run the utility disc in this way:
  http://windowshelp.Microsoft.com/Windows/en-us/help/bc1393cf-9f9c-79C7-0f91-9337c2c41f811033.mspx

  1. open the computer by clicking the Start button, click computer.
   
  2. right click on the hard drive you want to check, and then click Properties.
   
  3. click on the Tools tab and then, under check for errors, click check now.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  To automatically repair problems with files and folders that the scan detects, select automatically fix file system errors. Otherwise, the disk check will simply report a problem, but not to fix them.

  To perform a full disk check, select search and attempt to recover bad sectors. This scan is trying to find and repair physical errors on the hard drive itself, and it may take much longer to complete.

  To check for errors file and the physical errors, select both automatically fix errors in file system and search for and attempt recovery of bad sectors.
   
  4. click on start.
   
  Depending on the size of your hard disk, this may take several minutes. For best results, do not use your computer for any other tasks while it checks errors.

  Note: If you select automatically errors in file system of fix for a disc that is used (for example, the partition that contains Windows), you will need to reschedule the disk check for the next time you restart your computer.

  The reason that it says that the disk is in use by another process is because it is in use by the operating system (Vista), and that's why it must be run at startup, before the operating system loads fully.

  Another utility, you need to perform is the System File Checker, if you can get your computer to start, either normally or in Mode without failure.
  To run the System File Checker tool, follow these steps:
  Click Start and type cmd in the box start the search.
  Right click on cmd in the list programs, and then click Run as administrator.
  If you are prompted for an administrator password or a confirmation, type your password or click on continue
  At the command prompt, type the following line and press ENTER:
  sfc/scannow
  When the analysis is complete, test to see if the problem you are experiencing is resolved.

  Let us know what these tests are and how we can also provide assistance.
  Thank you

  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• When you try to run chkdsk, it tells me which cannot be executed, the Volume is in use by another process, but trying to run at startup, I am told that the chkdsk command has been cancelled

  When you try to run chkdsk, it tells me which cannot be executed, the Volume is in use by another process, but trying to run at startup, I am told that the chkdsk command has been cancelled. message also indicates that there are errors.  How can I me then chkdsk to run

  Hello

  See if these two tutorials to help you with this.

  "How to run the check disk at startup in Vista or Windows 7"

  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  "How to difficulty Chkdsk will not run at startup in Vista"

  http://www.Vistax64.com/tutorials/130824-CHKDSK-will-not-run-startup-Vista.html

  See you soon.

• You cannot connect because the logon method, you use is not allowed on this computer. Please, see your network administrator for more information.

  Whenever I enter my correct password in my windows account it rejects a message and it comes up saying: "you cannot connect because the logon method, you use is not allowed on this computer." See your network administrator for more information. "I can't seem to be able to enable or disable anything because the profile I'm using on my computer is the profile of"Guest ".

  Karima,

  Applicable to Windows 7.

  The following steps require administrator credentials.

  • Use the Windows + R or "Run" in the start menu, then type gpedit.msc.
  • Navigate to Computer Configuration > Windows settings > local policies > user rights assignment > consider all policies "prohibit the newspaper on" to check if your guest account is listed. Remove account from the list, and you should be fine to continue using your guest profile.

  Good luck.

  James

• I added the user name to log on to the computer in the active directory after adding, I can't connect to the internal application by using the user name and password...

  Hello

  I added the user name to log on to the computer in the active directory after adding, I can't connect to the internal application by using the user name and password...

  Please give the solution

  What happens when you try to connect?

  If you are able to connect using the different account, try running gpupdate/force.

  If the problem persists, you can open the discussion on:

  http://social.technet.Microsoft.com/forums/Windows/en-us/home

  What is responsible technical issues forum.

• I just got a new modem att wireless, now my phone cannot connect to the printer as it used to...

  just got a new modem att wireless, now my phone cannot connect to the printer as it used to...

  If AT & T has provided the modem, you can give them a call and explain the problem you are having. They should be able to help you. If you did not have all that in place, then it would be a little difficult to explain what you need to do... but... basically you would need to connect the modem and check the settings there and make sure your printer match the parameters.

• Multiple IPSec tunnels between two international research reports

  Hello, I have a no. 2851 to HQ and 2821 2nd site. Using IPSec VPN to connect two LANs and it works very well. Now, I want to connect another local network on each site through the same VPN. I want to separate the traffic between the LANs. Is this possible?

  You cannot use another crypto card if you must use the same IP for the peers you.

  If you have other addresses ip at each end to close the tunnel, you can use another crypto card.

  If the answer is no, then you can manipulate you acl of the traffic of interest to decide which lan can reach for witch lan.

• Satellite A100: Cannot switch to the internal screen

  I apologize in advance if the answer to this question is easy - I have major concern.

  I am an instructor and yesterday was to use a projector to clients to connect my laptop to a session. All was well at first with the laptop screen and projector showing the image, but one of the participants decided to help me and I lost the picture on my laptop (even if not connected to a projector)

  When I turn on the laptop everthing shows on screen (Toshiba etc.) until I get into Windows, then it shows just the ripple background with no icons, however if connected to a projector is displayed.

  I tried fn F5, but is not offer me options normal and I can't reset it.

  Thanks in advance for any help provided

  I put t know what the problem is here, but using the FN + F5 key combination, you should be able to get the LCD screen only. If it works please check display properties. Perhaps it is - someone has activated the extended view option and the value of LCD as second.

  Check this possibility.

• cannot turn off the planned research

  I can't disable searches in FF, and whenever I have run FF it goes to the search preferences page and I have to save my setting before I can access the home page, this happens EVERY time. I did all the stuff cookie, erased them enabled them, them deactivated and reactivated them, tried every setting I can think of but it still does the same thing and I have to go through the registration procedure of settings
  I thank God for Chrome

  It could be that Google search is your home page. You can try to change/remove unwanted in the Tools (Alt + T) home pages > Options > general, next to Homepage: and add a new one. Options > general. If the home page has been added by an extension and is reset to Google search, you find the add-on Tools (Alt + T) > Add-on, Extensions (left) and either change the settings or disable / Remove the extension.

  If Firefox is stuck in a session restore , you can try to delete the session: type about: sessionrestore in the address bar (address), hit enter, click start a new Session , restart Firefox and check.

  Research predictive in Google is a feature of Google, and you will need to go to Google search options to turn it off.

  It would also be helpful if you could post a screenshot: Add images: > Browse... below to post a reply on this page.

• Cannot sweep of the MAC Book Pro using OfficeJet 8600

  I have used my OfficeJet Pro 8600 to scan until last week.  So I rebooted the software of HP and I still can't analyze.  I tried the Apple via AirPrint (version 2.0) drivers, still does not work.  Prints well but will not scan.  10.10 OSX is loaded but it worked for weeks after that.  The strange thing is that analyze the Mac of my wife (an old portable) with OS x 10.10 using version 1.0 of AirPrint.  Ideas?  I tried all the resets of the queues, etc.

  Hi @Cap1007

  Welcome to the Forums of HP's Support. I understand that you are no longer able to scan using your printer Officejet 8600.

  We know that this is not a hardware problem that you are able to scan the older Mac Help. your wife I included the document Mac OS X: Scanning Software done is not open or stops responding .

  Please let me know the results.

• Cannot get on the Windows Update site using firefox. It keeps saying that the connection was reset

  Original title : Could not get the update of windows

  I use firefox as my web browser and I can't on the Windows Update site, it just telling me that the connection was reset.  I click on try again, but just showing the same thing please help

  What type of Internet connection you are on, wired or wireless? If you are on a wireless connection, try to switch to a wired connection and try the download with Internet Explorer.

  1. open Internet Explorer (only!) to http://support.microsoft.com/kb/910336> [ignore the title, etc.], reject modes and then AGGRESSIVE and pop-up troubleshooting automated, then run difficulty he 50202 in DEFAULT. [Ignore warnings "Not recommended", etc.]

  2. restart & test.

  Full disclosure: the difficulty operating in AGGRESSIVE mode will remove your update history but not list the updates installed in Add/Remove Programs (Windows XP)

  UTC/GMT is 16:46 Tuesday, April 24, 2012

• Cannot type in the Korean IME by using Vista Home Premium X 86 (SP1).

  I've added Korean keyboards under regional and Language Options, but the language bar does not appear on the toolbar and using the shortcut keys I still can't type Korean characters.  I have Win7 on another PC and following the same method works very well.

  Re-install the control panel language pack

• Include the attribute custom report using the disc

  I'm to customize a script provided by Alan Renouf in his PowerGUI Powerpack.  The script I'm customization in the Powerpack is named 'VM disk sizes.

  His screenplay does everything we need from a point of view of output except that we can also include a custom attribute (Custom Field) VM as well as the information of the disk space.  I have included the below custom script, please note that this is a script/PowerGUI PowerPack we customize but was initially written and provided by Alan Renouf and all credit for this original work must be given to Alan.

  I have included our custom below script and have "in bold Red" line in the script that does not work:

  $AllVMs = get-View - ViewType VirtualMachine. Where {-not $_.} Config.Template}
  $SortedVMs = $AllVMs | Select *, @{N = "NumDisks"; E={@($_. Guest.Disk.Length)}} | Sort-Object-down NumDisks
  {ForEach ($VM to $SortedVMs)
  $Details = new-object PSObject
  $Details | Add-Member-Name name-value $VM.name - Membertype NoteProperty
  $Details | Add-Member - MemberType NoteProperty-name CustomFields-value (($VM.)) CustomFields | %{"$($_. Key) = $($_.) (Value)'}) - join ',')
  $DiskNum = 0
  Foreach ($disk in $VM. Guest.Disk) {}
  $Details | Add-Member-name "drive$ ($DiskNum) path"-MemberType NoteProperty-value $Disk.DiskPath
  $Details | Add-Member-Name "Disk$ ($DiskNum) Capacity (MB)"-MemberType NoteProperty-value ([math]: round ($disk.) Capacity / 1 MB))
  $Details | Add-Member-Name "Disk$ ($DiskNum) FreeSpace (MB)"-MemberType NoteProperty-value ([math]: round ($disk.) FreeSpace / 1 MB))
  $DiskNum ++
  } # end foreach nested
  $Details.PSTypeNames.Clear)
  $Details.PSTypeNames.Add ('Virtu-al'.PowerPack.VMGuestDisks) '
  $Details.PSTypeNames.Add ('Virtu-al'.PowerPack.VM) '
  $Details
  } # end foreach

  When you use the Get view as seen on the first line of the script, it appears the CustomField information not available in the generated view.  How to develop the view to include CustomFields/CustomAttributes for each virtual computer in our environment and then report on their subject?

  Please let me know if I did a poor job explaining the scenario and what I'm after here.  Any help is greatly appreciated!

  Hello, jSun311-

  Yes, you are right - there is no such thing as the "CustomFields" property on a managed object VirtualMachine .  You can always get the names and the corresponding values of the custom fields, you just have a little.  For example, you could change the line to:

  ...## make a comma-separated string that holds the custom field key/value pairs, like "cust0 = myValue0,cust1 = myDateInfo"$Details | Add-Member -MemberType NoteProperty -Name CustomFields -Value (($VM.Value | %{$oCustFieldStrValue = $_; "{0} = {1}" -f ($VM.AvailableField | ?{$_.Key -eq $oCustFieldStrValue.Key}).Name, $oCustFieldStrValue.Value}) -join ",")...
  

  and you should be happy as a clam.

  BTW, this call Get-view on your first line could be optimized a little using the - Filter parameter, like:

  $AllVMs = Get-View -ViewType VirtualMachine -Filter @{"Config.Template" = "false"}
  

  Pretty minimal in this case, but can be very useful in other scenarios of Get-View.  And, you may want to retrieve only the properties of the managed VirtualMachine object that you plan to use, so that the memory usage is reduced to the minimum, speed is optimized, etc. (do you this by using the - Get-mode property param).

  Anyway, how does do for you?

• How to access the internal memory of Blackberry?

  Hello
  I am currently to access the file operation in the SD card. I want to access the file operation in the internal memory of Blackberry?

  To access the file on the internal memory operation use file:///store/home/user/filename