Similar Questions

• Connection of third-party cameras Cisco SX80

  Is it possible to connect any third party camera Cisco SX80.  I'm looking to plug pregnant vaddio Auto Trak 2.0 camera to the Cisco SX80 instead of the Precision60 or speaker track monitoring cameras.

  We use third-party cameras (Sony) with all of our SX80, however, they must be controlled by a third party such as AMX system. Works very well for us - however, none of us is "followed by speaker.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Overheating of Cisco SX80 double camera

  We have a SX80 Cisco codec with dual cams installed at the front of the room who the speaker / auto track feature. This room was originally installed about 1 year ago. And just recently, I started to notice some flickering with capture our video cameras in the room of the VTC. In addition, the Auto Track feature pans and zooms to an individual speaker during a video call no longer works and manual tabs on the touch screen to control the cameras are inoperable as well.

  At this 1st, it was just the flickering I noticed and I simply unplugged feeding on both cams for a little to solve this problem. However, a week later... twinkling is back, but now came the problem with the Auto Track and manual controls for each input. After power to the Assembly of the whole camera to mount on the front of the room for about 30 minutes, it seems to solve the problem. But now again once this morning the Auto track does not work and the emission of heat from the base that the cameras are on is very hot.

  I've determined that the power that feeds on the Assembly of the camera at the front of the room is separated BC from the system of room in other words, when you stop AV system of the room through the touch screen, it is always power supplied to the Assembly of the camera with a separate. What has power constantly running on the cams, making them HOT.

  Has anyone else had this problem with the Assembly Speaker SX80 track? And if yes, what is the resolution other than intermittently, turning them off the coast from time to time. I know that this device is relatively new, so wonder if the circuit design within the frame of the Assembly of the camera is shotty and needs reworking.

  Thanks in advance!

  Check out this link. It explains your problem

  https://BST.cloudapps.Cisco.com/bugsearch/bug/CSCuu06180

• CISCO SX80 - PrecisionHDMC 1080 p 12 X CAMERA

  Hello

  I want to know if the camera precision HD 1080 p 12 x is compatible with the Codec SX80.

  Thank you

  Ivan

  SX80 does not support Cisco TelePresence precision HD 1080 p 12 x.

  It supports

  Precision 60

  Cisco TelePresence precision HD 1080 p 4 x S2

  SpeakerTrack (with an accuracy of two 60´s)

  / Magnus

• Cisco sx80 - how to change login/password SIP

  Hello

  could someone help me with the following question:

  How to change the SIP login and/or password via menu 10 touch (indeed, there are these lines in the menu but I can't edit them)? I don't know how to do that through the web interface.

  BTW, I SX80, tap 10 and 60 SpeakerTrack if it matters.

  Thank you!

  Use the wizard:

  Settings-> administrator-> Provisioning-> start-> Cisco VCS provisioning Wizard

  Marius

• Cisco SX80 removing 'no camera not connected' OSD warning

  Hello.

  How can I remove the warning message "No camera connected" screen on?

  I use 4 entry and I do not need the camera.

  Thanks again!

  I just tested with a SX80, and from what I can tell, there is no way to disable the message will always appear unless a video input is detected on either HDMI 1 or 2.  What is the possibility of using either people like entry and change the configuration on it must match the input 4?  Another option is to move the OSD to another screen that you do not use, but this means that you will see all messages screen if they appear.

• Cisco SX80 startup after power loss

  Hello

  A really quick...

  I have a SX80 deployed to a remote location and we had a few cases where the device was inadvertently disconnected the power.  When the power returns, the device does not return to the operation without someone pressing the power button.

  Is there a way to force the device to power up to a previous state on the restoration of the power, rather than the stop State?

  I know it's a simple thing, but it would make my life a little easier if I didn't have to talk to someone by the power button...

  If you want to know if a person is to hit the power button, locate the following line in application.log under Diagnostics > logs on the SX80.

   PowerButtonSensor I: powerButtonReaderTask::powerButtonPushed

• Randomly call in Cisco TelePresence SX80.

  I have a recurring problem of many unknown incoming calls in a Cisco SX80 recently deployed. An example of the address that we get these calls from the East [email protected]/ * / I have no idea what is the part of the address in 1986, but the 129.59 address is the IP address of the codec. I am somewhat a novice in the world of VTC, so I am at a loss on how to stop the calls. Automatic response has been disabled pending just so that the device can be used.

  I assume that the system uses an accessible public IP address?  If it uses a public IP address, you should put behind your firewall with NAT, or allow only traffic from known IP addresses.  If you don't use a SIP, you can enable turn off completely, however if you are, you can disable SIP ListenPort and activate outgoing SIP so to avoid these calls, see bug CSCue55239.  There is a form any of these calls which will appear as coming from "cisco", the only way to prevent these is to put endpoint behind your firewall and use NAT or an ACL.

  You can also watch here for a bit more information, anyone-know-why-edge-95-mxp-will-call-itself, as well as further discussions in the forums associated with these types of calls.

• Switching machine

  Hi team,

  I came across a problem to go in camera in CISCO SX80. All faced a similar question resolved the same?

  Scenario:

  During the passage of portal web cameras near site sees camera switching but camera from the remote site view does not change.

  Whereas, in the same system, when the camera view went from the TP changes camera view for both near and away from the site.

  What I'm missing here?

  Thank you

  Haj

  Hi Haj,

  Also, I have recreated the same question in my lab and saw that question appears not only on the CE8.1.X version, but also on TC7.3.X and CE8.2.X also.

  I believe that swapping camera of the web interface does not send a command API at the end during the video call, well that discovers works as expected.

  I chose 2 camera and still at State, I get 1 camera for video source:

  image.PNG

  

  I will update the bug already created (CSCva64137) for other versions of software also. In the meantime, you can have this work around of choice main video source using the touchscreen.

  Thank you

  Shefali Sharma

• Camera approach speaker used with third party cameras

  We currently use a Cisco sx80 system and you need to add a camera to track speaker. We currently use

  Shure MX393/O - Omni mic

  third-party microphones. Speakertrack will work with these pickups?

  Thanks in advance

  Double post.

  speakertrack-3 rd-party-microphone

• Cisco QoS SX80

  Hello

  I would like to ask for help on this.

  A client have SX80 Cisco video endpoint, and the network administrator wants to configure QoS for this endpoint.

  Here are the recommended settings:

  * Replace video type of service (ToS) 41 AF - recommends that the network administrator to change the video 41 AF priority that has a priority over high and protected to the network congestion.
  * Tag class EF - EF voice traffic has priority higher than our MPLS (Verizon) Setup.
  * Adjust the audio codec to use G.729 only - G.729 audio codec uses the compression of voice that limits the VoIP traffic.

  With the recommendations above, what are the settings must be configured from the SX80 Cisco codec?

  Thank you and best regards,

  Acevirgil

  You can configure QoS settings in the network via the web gui or CLI section; XConfiguration network

  Only DiffServ using decimal values are supported, and the recommended values are

  • audio and video 34 (equals AF41)
  • data 22 (corresponds to AF20)
  • 26 signal (equals AF31)

  I don't know how you would limit so that it uses a particular audio codec.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• The Cisco Telepresence SX80 solution help

  Hello

  I really want to get your help in this scenario.

  We have 2 branches and planning to set (for the first site 3 SX80 of three meeting rooms) and (one SX80 for another branch).

  We have all communications between sites works well and phones are connected using CUCM 10.5 my question how connect us these 2 branches to collect and SX80 features on site with a minimum of equipment?

  Can make us the video call normally trunk Sip or H323 or do we have to express way / telepresence Server?

  Please notify.

  Thank you

  Hello

  Could you say how the branches are connected to each other? It is through the Internet or VPN? Then we will know how to position the highways.

  If you have CUCM you will use as your calling command for your SX80s and write them down on it as SIP endpoints.

  SX80 endpoint can be ordered with multisite option so it can appeal a multisite up to 5 participants. You will need Telepresence server to host concurrent conferences with more than 5 participants in a conference. You also need a conductor when implementing telepresence servers to manage the resources of the Conference.

  Kind regards

  Acevirgil

• SX80 - Cisco Telepresence

  Hi all;

  Help me please check how many sites, the support of CTS-SX80-IP40-K9?

  I set up a video conference room 6 sites. can suggest you for me?

  Thank you best regards &;

  Klein

  While it would not necessarily be to pretty on the screen, you can do with two SX80s with multi-site - call half endpoints of one and half of the other, then use another call to link the two.

  Then SX80 number 1 call settings 2 and 3 and also SX80 number 2.  SX80 number 2 would then call endpoints 5 and 6.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• SX80 h323 call question

  Hello

  I have a SX80 with software version THIS 8.2.2 on my call manager v11.5 via sip.

  I can call all internal extensions and can call external pstn.

  It's more the CV out there uses H.323 so that when I try to call and conference H.323 via ip call is rejected, after having checked the call log, it's using sip and H.323 not although h.323 is enabled and the direct value (no watchman),

  to work around this problem, I have informed my client to add the address called as a contact and manually select the Protocol of control for this contact.

  But this isn't a solution for my client, because it is possible from the web interface and users of the Conference are high-level management and do not have the time to do so.

  Please I need solution because it is not acceptable to me. and yes I have tried to use x * x * x * x or [email protected] / * / with no use using all the don't SIP not h.323

  Best regards

  Since the touch screen you can add h323: in the IP Address, this will force endpoint to compose using H323.

  Example = h323:1.1.1.1

  Other, you must deploy servers of VCS/Highway to the interoperability of SIP H323, http://www.cisco.com/c/en/us/support/docs/unified-communications/telepre... please check

  Kind regards

• Capabilities with the right Protection and control of license

  Hi people,

  Just check that I understand the limits of a capabilities of clients with the power of fire with only the Protection/control.

  They will be

  1 / receive updates of poorly known ip addresses

  2 / receive updates for pre-treatment Snort rules - VDB files

  3 / be able to create manual URLS to perform a kind of Url rules in function

  4 / geolocation?

  They will not

  1 / have any possibility to send / receive file layout information

  2 / have any possibility to use Url categories

  3 / are free to set up rules to file based Malware

  Hi Evan,

  With a minimum of Protection and control, you can start the management of firepower. If the customer requires awareness of users according to a user with the license agent host Firesight will do as well as the Protection and control. You can create reports user based with the latter.

  Here's the URL and ports must be opened for the Firesight get necessary updates.

  SRU/VDB/Patch/all updates
  Ref 1 > http://www.cisco.com/c/en/us/support/docs/security/firesight-management-...

  Ref 2 > http://www.cisco.com/c/en/us/support/docs/security/firesight-management-...

  Here is the detailed information of the download server:

  Domain: support.sourcefire.com
  URL: https://support.sourcefire.com
  Port: 443/tcp (bidirectional)
  IP address: 50.19.123.95, 50.16.210.129

  Additional IP addresses that are also used by the support.sourcefire.com (in the method of Robin) are:

  54.221.210.248
  54.221.211.1
  54.221.212.60
  54.221.212.170
  54.221.212.241
  54.221.213.96
  54.221.213.209
  54.221.214.25
  54.221.214.81

  For amp
  Ref 1 > http://www.cisco.com/c/en/us/support/docs/security/firesight-management-...
  Ref 2 > http://www.cisco.com/c/en/us/support/docs/security/sourcefire-amp-applia...
  Using port 443 (bidirectional)
  Or Legacy port 32137 (out)

  For the URL filtering
  Access to the 'database.brightcloud.com' and 'service2.brightcloud.com '.
  the IP address is dynamic
  Ref 1 > http://www.cisco.com/c/en/us/support/docs/security/firesight-management-...

  Using port 443 (bidirectional)
  Using port 80 (incoming)

  For downloads of feed security intelligence:
  Access to intelligence.sourcefire.com
  The server uses the round robin scheme of IP address for the NLB, availability and fault tolerance. Therefore, IP addresses can change, and it is recommended that the firewall is configured with CNAME instead of an IP address.

  Ref 1 > http://www.cisco.com/c/en/us/support/docs/security/firesight-management-...

  Ref 2 > http://www.cisco.com/c/en/us/support/docs/security/firesight-management-...

  Using port 443 (bidirectional)
  Using port 80 (incoming)

  Kindly correct brand and rate if this helps.

  Concerning

  Jetsy