Carousel stops when the mouse on the image?

Similar Questions

• MacBook Pro stops when the lid closes, loses the open tabs and background image...

  Hi all

  I recently had a new hard drive installed in my 2012 13-inch MacBook Pro. I am running El Capitan 10.11.2. Since then, my computer cuts automatically to the bottom when the lid is closed, losing all Web pages, and for some reason, some background, I've saved. (My browser is Mozilla Firefox and it prompts you to restore me the tabs lost, which he will).

  The led standby does not blink or light up when the computer is turned on, it will turn on only at startup. At startup, the login page is displayed, and after that I entered my password it takes about 15 to 25 seconds to load and open my account. What is going on?!

  Summary:

  Stop when the lid is closed,

  Loses the background image & open Web pages.

  Standby blinks only when starting,

  Time of loading extended after logging into my account.

  Any help would be greatly appreciated! Thanks a lot for reading.

  uhlexia wrote:

  Hi all

  I recently had a new hard drive installed in my 2012 13-inch MacBook Pro. I am running El Capitan 10.11.2. Since then, my computer turns off automatically when the lid is closed.

  Take it back to the repair as well as your receipt of repair shop.  Apple has a 90 day warranty on all repairs.

  

• Acquisition of CL crashes when the image is too light?

  I have a strange problem and I can't be sure either the camera or the Board of Directors: basically, in any method of execution, when the image is too light, the acquisition stops and I get a timeout in MAX. It is with a PCIe-1433 and Point grey Gazelle. Blockage of the camera and restarting acquisition works very well. This occurs at any time, that the majority of the image gets to 80% brightness.

  To make things more confusing, this can sometimes be corrected by the passage of cable (the same 5 meters OR cable model, but just another); now, however, I have a couple of cameras that show that all cable and so I need to get it figured out. It would certainly be a problem of camera or a combination and so I contact PMP as well. Anyone has any ideas on this? Thanks in advance for any info!

  I would suspect that your CameraLink cables cannot meet performance requirements for speed of clock and the distance, that you are running. Unlike most new buses at high speed, the underlying mechanism of encoding on the wire for CameraLink has a characteristic resistance to noise (even among his own peers) depends somewhat on the actual data values are transmitted. Since the frame control signals are passed in the same channel as the content of the image itself, if there is some noise/interaction between them on the wire, they could cause problems of behavior on the side of the acquisition.

  If your camera supports the lowering of the frequenency of the clock, you might be able to check that helps the behavior. If it does, I recommend trying to replace the cables with superior quality-those. The CameraLink Committee now has a test of official certification of cables which is very comprehensive. I would say in ensuring that the cables you are using are actually tested for these certification tests.

  Eric

• Hallo why? When I update ios. When the image has finished error itunes and usb

  Hallo why? When I update ios. When the image has finished error itunes and usb

  Connect the iPhone to the computer that you are synchronizing usually with

  and follow the prompts to iTunes on this computer. If you

  do not generally in sync with a computer, you should always use

  iTunes on a computer to complete the update.

• Satellite Pro L500 - stops when the power cord removed

  Toshiba Satellite Pro L500 stops when the power cord is removed even with the battery to 100%. I removed the battery and all the indications associated with battery answer correctly. For example turns off, Toshiba Health Monitor also indicates when the battery is removed. If installed Health monitor indicates that the battery is at 100%.

  Someone please help. I have not installed anything new.

  Hey,.

  For me, the matter is clear: the battery can't hold a charge so the laptop will be shut down because it has no power.

  I think you need to replace the battery with a new one and you can get a provider of service authorized in your country. Simply contact the guy and ask that they can tell you how much it would cost.

  You can find a list of all FSA here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Good luck! :)

• Satellite Pro L10: CMOS clock stops when the OS is not running

  Hello

  We know a reason why the cmos clock would stop when the operating system does not (phone off), the laptop is 18 months old, I've updated the bios tries to give him a good boost, but no effect, he was also in charge for 24 hours.
  Any advice would be great.

  See you soon
  Paul

  Hello

  Usually if the BIOS date/time is wrong and always changes, the RTC battery which is mounted on the motherboard fails.
  In this case the CMOS battery needs to be changed or maybe only removed for awhile

  If your laptop is 18 months, the guarantee must be valid.
  Generally if you have registered on the page of Toshiba notebook the warranty covers all repairs for about 2 years (24 months).

  In this case, I would recommend contacting ASP in your country, because the technician must be able to solve this problem very easily.

  Good bye

• New Yoga 14 stops when the lid closes

  I just got a new series of Yoga 14. Sometimes, but not always, the laptop stops when I close the lid, even when it is plugged. I already looked at the option to 'choose what happens when the lid is closed' and it is set to sleep, no downtime.

  Any ideas on how to solve this problem.

  Hi Nickajeglin,

  Welcome to the Forums

  According to the request, we understand that you are facing problem with the system stops when the lid is closed in your Lenovo 14 yoga.

  As you mentioned that you have changed the setting to sleep, try changing to do nothing option and check also the question, if still the issue persists then uninstall and reinstall the power management and check the issue.

  Click here to for 10 windows power management.

  Let us know the result.

  Best regards

  Ashwin.S

• While the loop does not stop when the two values are equal using equal to comparitor

  Hello world

  I have a really, really strange bug. I have a LabVIEW VI that change a chain on a power supply. I have a start and a stop voltage and use a while loop to increment the device. For example if I want to scan from 1, 2V to 2.2 V in 0.2 V incremements, the program will end when "The current tension" = "stop the tension." And it works very well!

  However, when I start - 3 V and want to stop to say-0.8 (new in 0.2 V incremements) the program does not stop when "The current tension" = "stop the tension." I checked with the probe close to what should be the end of the race and - 0.8 V goes both of the entries ' equal to ' comaprison operator, but that his can't trigger a real result.

  It's very strange for me. Espeically as if I'm going - 0.8 V to-2 V but decrement of-0.2 V, the program stops correctly!

  I am very confused!

  See you soon!

  Search on: comparison of floating-point numbers

  The second thread is particularly relevant. This discussion was 2009, but you can find that the same "bug" being reported to enter the end of the 1980s.

  Mike...

• Explorer.exe stops when the computer is shut down

  Explorer.exe stops when the computer is shut down

  Hi DickKimberley,

  ·         What exactly happens when you try to shut down the computer?

  ·         You receive an error message error code?

  ·         Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: I suggest you to consult the article in the Microsoft Knowledge Base and check.

  Advanced Troubleshooting for shutdown problems in Windows XP

  http://support.Microsoft.com/kb/308029

   

  Method 2: If the method above doesn't follow the article mentioned below.

   

  Windows stops responding during Windows XP shut down

  http://support.Microsoft.com/kb/307274

  Let us know if that helps.

• computer Vista laptop does not stop when the lid is closed

  I have all the correct power settings. mode when the lid is closed, I tried setting Hibernate and sleep. It just keeps running and running, I'm afraid it will overheat. but it should stop when the lid is closed, correct? Thank you sissy

  Hello banditpunpun2,

  Thanks for the return of the response.  I also go to your manufactures website and confirm you are updated with the lates drivers, updates the firmware and BIOS.  I even watch the forums on the manufacturer's Web site to see if others have experinced the same question.

  Please let us know status.

• Dell inspiron w / xp sp3 stops when the lid closed only in mode standby

  Dell inspiron e1505 on windows xp sp3 will stop when the lid closed mode standby. In "idle mode" it shuts down for a few seconds then screen turns on and I can work as usual.  Why is it turn off in standby mode?  Happens in AC mode and battery.  is it a software problem or a hardware problem.  I see others with the same problem and vista dell.

  http://support.Dell.com/

  Dell support.

  http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_us?c=us&l=en&s=Gen&redirect=1

  Contact Dell

  http://en.community.Dell.com/forums/

  Dell forums

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• BlackBerry BB Z10 Z10 stops when the battery indicator shows about 35%

  Z10 BB stops when the battery indicator shows about 35 percent without any warning. Does not illuminate until the charger is plugged. Immediately shows charge remaining 40% +.

  Please advice.

  Stephen

  Hello

  Here is a solution I tried after lookng through various forums and type of works for me. A common thing in most of the solutions is to take the battery and sim card out, leave like this for 1-2 hours and put them, I found back in and turn it on. I'm not sure of the logic behind it, but I remember reading that this overshadow the phone battery problems (connected incorrectly - essentially a reset) and begins to charge.

  I tried it 2 days back and I see that it worked for me, at least until now. I cross my fingers.

  I hope it's useful, works at least for few of you.

  Thank you all for the suggestions.

• Will be that the download stops when the computer goes into sleep mode?

  Will download, install, or all these action stops when the laptop goes to sleep.

  MK

  Yes, it will be.

• My computer is no longer warn me entry stop when the battery reaches the critical level.

  My computer is no longer warn me entry stop when the battery reaches the critical level. Officially, it shows a warning sign and told me to shot or recharge the battery when it gets to level criticism, but now he can't, but stop just when the battery has reached its critical level. No warning sign more.
  What should I do to get the warning before the pc turns off when the battery is at its critical level.
  My pc is hp laptop mini 110-3100. Start Windows 7.

  Hi Sage180,

  ·         Did you change in the computer before the show?

  Follow these methods.

  Method 1: Run the Troubleshooter of power.

  Method 2: Follow the steps in the article.

  Solutions to common battery problems

  Battery meter: frequently asked questions

  For reference: take care of your laptop battery

• Printing of the .pdf of the 2013 project file will stop when the name of the file must be written. Project 2013 crashes. Anyone know what the problem is between 2013 project and Adobe Acrobat 9?

  Printing of the .pdf of the 2013 project file will stop when the name of the file must be written. Project 2013 crashes. Anyone know what the problem is between 2013 project and Adobe Acrobat 9?

  The family of products Acrobat 9.x passed in mid-2013 "end of Support".
  Using Acrobat 9 of MS Project via PDFMaker stops with Office 2007.
  To 2013 Office support, you must use Acrobat XI (11.0.1) or newer.

  A good reference:
  https://helpx.Adobe.com/Acrobat/KB/compatible-Web-browsers-PDFMaker-applications.html

  Acrobat Pro and Standard DC are what are currently available for purchase.

  Be well...