CDBOOT cannot start from code: 5 CD

Similar Questions

• Cannot start from the CD: Error Code 5. __Asking driver primary IDE channel.

  I install a new copy of windows 7 on my old computer. My computer have no major problems from Advisor Windows 7 report. When the system boots on the DVD I got the error message cannot START FROM the CD: error 5 CODE. Also, I can't start XP installation. When I get to the part on which partition to install I got the message to load a driver. He asks me to load a driver for the MAIN IDE CHANNEL. I have search on Intel, Gigabyte and other internet sites but have not found a specific driver.
  My computer is:
  Processor Intel P4 1.7Ghz
  15 GB OF RAM
  GeForce 7600GS
  320 GB IDE HARD DRIVE
  Card mother Gigabyte GA-8ITX3
  Intel 820 Chipset family with 82801BA (ICH2) I/O controller.

  Help, please!

  P.S. noticed that 2Angel had a similar problem but no solution.

  Error code 5 - can't boot from DVD

  Some people have reported that from the installation of Windows 7 so that Windows XP/Vista is running can help with this error. Update your BIOS may also help.

  Here is a workaround that can also help:
  http://www.SevenForums.com/installation-setup/2591-boot-error-code-5-a-2.html#post31719

  Questions about installing Windows 7?
  FAQ - Frequently Asked Questions from Installation Windows 7 & responses

• This device cannot start. (Code 10) DVD

  I have a HP Pavilion a1240n runnning Windows 8.1 nor the ATA DVD HP 740 b device or appliance IDE\CdRomLITE-ON_DVDRW_SOHW-work. I get the following message appears in the Device Manager box

  This device cannot start. (Code 10)

  The specified request is not a valid operation for the target device.

  Tried to deactivate, activate, uninstall and reinstall. The drivers are all to date. Are these DVD and CD with Windown 8.1 comaptibe?

  I also have problems with the computer recognizing my drive external USB and iPod.

  Impossible to update a such there need of files on the disk and hard drives do not work.

  Help please I know it's an old computer, but really like it to be fully functional. Thank you.

  Hello:

  Try each resolution 2, 3 and 5 from the link below to solve the problem you are having.

  https://support.Microsoft.com/en-us/KB/314060

• Another type of "this device cannot start. (Code 10) "failure

  Environment:

  EM250 Netbook (basically an Acer)

  Windows 7 Starter

  Sansa Clip + 4 GB

  Version V01.02.15A

  Basically, is that the device will not work in MTP mode.  Works very well in MSC, but PSG is necessary because the unit was purchased specifically for use with audible.com audiobooks, and it does not have MSC mode.

  Got the "this device cannot start. (Code 10) "goodbye, looking for inproperties after the driver will not load.  Two "insertion events" beeps during the process

  Tried the "'Net local service localgroup administrators / add" to http://kb.sandisk.com/app/answers/detail/a_id/192 "

  The command was successful, but has not fixed the problem.

  Tried updating all the drivers I could find.  A ran the sansa updater to make sure everything was up to date.

  The device can't the same way on an Acer netbook and similarly on a Windows XP desktop.

  I look at the installation in the control panel Device Manager, you can see the low level driver loading and the portable device become active, but then the level user MTP driver fails.

  from the event viewer, I see the following events associated with inserting

  Event ID 24576 information: "Drivers have been correctly installed for device USB\VID_0781 & PID_74D0 & REV_: 8<>

  25089 Information event ID: 'it was not possible to access the device () after installing the drivers. Error code 0 x 80070651. »

  Event ID 10110 critical: "there was a problem with one or several drivers from user mode and the hosting process is finished.  This can temporarily interrupt your ability to access devices. »

  Event ID 10111 critical: "the device USB MTP Device (location Port_ #0003.Hub_ #0005) is offline due to a user-mode driver accident."  Windows will attempt to restart the Unit 5 times more.  Contact the device manufacturer for more information on this problem. »

  I suspect the key error is the "error code 0 x 80070651.", but I have not found a solution for her online that works

  I tried the technique of driver to uninstall without success.  After the step to "Discover new material" he would miss just the same way.

  I just found a way that worked well.  I have re-installed the firmware.  Not through the Sansa Updater.  This program would simply note that my Clip + release the latest version, then give up.

  Instead I manually re-installed the firmware using the process that the people of Mac and Linux have to use. detailed on the

  http://forums.SanDisk.com/T5/clip-Clip/Sansa-clip-firmware-update-01-02-15/TD-p/150227

  In short, it is to download the zip to show off to

  http://mp3support.SanDisk.com/firmware/ClipPlus/clipplus01.02.15.zip

  Unizip it, then move the two files to the root of the Clip + while it is mounted in MSC mode.

  When he unplugged the updates the firmware.

  I don't know if it was a step necessary or not, but I also reformatted the Clip + menu.  In any case, it now amounts to PSG. mode.

• This device cannot start. (Code 10) Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  Map #2 Microsoft Tun Miniport
  This device cannot start. (Code 10)  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.
  ???

  Hi AnaSk,

  (1) since when are you facing this problem?

  (2) remember to make changes?

  The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows.

  Download and install the latest drivers from the computer's network adapter or the website of the manufacturer of the device.

  See the article below

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104

• My sound card does not work after working yesterday. "This device cannot start. (Code 10) »

  Hi support team!

  I have a HP Pavilion zv6000 and my audio does not work and I enter the Manager of devices and displays this error: "this device cannot start. Code 10 "after this I installed my audio driver from the site and still the same problem.

  With repsect, OZNalex.

  

  OZNalex wrote:

  Hi support team!

  I have a HP Pavilion zv6000 and my audio does not work and I enter the Manager of devices and displays this error: "this device cannot start. Code 10 "after this I installed my audio driver from the site and still the same problem.

  With repsect, OZNalex.

  

  Hello

  First do a hard reset.

  Please go through this Hotfix from Microsoft for the error you are getting.

  Please uninstall & update audio driver & BIOS after checking, you have such version specified in the site pilot here on the website of the HP product . Reboot after that. Do the troubleshooting in the Microsoft Fix document.

  When you're done, shut down the laptop.

  Disconnect the power adapter and remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

  Robinet tap away at the key ESC that you start the computer to launch the Start Menu, and then select F10 to open the BIOS menu.  Press F5 to load the default values (sometimes it's F9, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press F10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  Check if its working

  Thank you

• This device cannot start. (Code 10) with a hard usb pen and readers for windows 7

  Recently, I used acronis true image to migrate my hard drive to an ssd from 250 to 500, the problem is on the new drive I get "this device cannot start. (Code 10) "error every time I try to use a USB key or external hard drive on the new image, the old image is fine. I tried all the usual alternatives to surf the web;

  Reset

  Re-creating image several times.

  uninstall all the usb drivers on Device Manager Associates,

  update drivers,

  using the microsoft error fix program (fails to answer to find bespoke online solutions).

  Any help would be useful.

  Kind regards.

  Hello Scott,

  Thanks for posting your query in Microsoft Community.

  I understand that you have problems with USB devices in the computer.

  I would like to know some more information on this issue to help you better.

  (1) that Microsoft fix program error have tried?

  (2) remember to make changes to the computer, before this problem?

  In the meantime, you can try to follow the following suggestions to solve the problem.

  Actually code 10 occurs mainly because of devices and hardware driver issues or because of compatibility problems between the drivers of equipment and additional software that is installed on the windows.

  FIX: "this device cannot start" error Code 10 in the Device Manager in Windows

  http://support.Microsoft.com/kb/943104/en-us

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  Registry backup
  http://Windows.Microsoft.com/en-GB/Windows/back-up-registry#1TC=Windows-7

  I hope this helps. Otherwise, feel free to write us again for more assistance, and we will be happy to help you.

  Thank you

• No audio (this device cannot start. Code 10) on the D630

  Hello

  I have Windows XP with SP2. Fresh installation, the laptop is new and I have problems

  with my audio device (this device cannot start. (Code 10). From the BIOS, I have after I have Sigmatel 9205

  audio device.

  I have updated the bios to A07, chipset, and later installed audio driver of dell does site already whith no results.

  Suggest what I need to do more?

  10 X,

  ADI

  
  

• Teredo Tunneling Pseudo-Interface - This device cannot start. (Code 10)

  Original title: code10microsoft toledo tunnelling

  We think we've found a driver but we are not sure because he vomits again code.10

  Hello

  1. don't you make changes to your computer before this problem started?

  2. What is the brand and model number?

  If the device has a FailReasonString value in its hardware key, that string is displayed in the error message. The driver or enumerator places this registry string value there. If there is no FailReasonString in the hardware key, you receive the following error message: this device cannot start. (Code 10)

  You can try the following steps and check if that helps you solve the problem.

  Method 1:

  Open the Device Manager and the analysis of new hardware and select 'Show hidden devices' in the view menu and check if you find errors.

  a. Open command prompt with administrator credentials (type CMD and right - click Run as administrator).

  b. Type "netsh" and ENTER.

  c. Type "int teredo" and ENTER

  d. type 'set disabled state' and ENTER.

  e. open the Device Manager and uninstall "Teredo Tunneling pseudo-interface".

  f. Open command with administrator credentials prompt once more.

  g. type netsh + ENTER.

  h. Type "int ipv6" + ENTRY

  i. type 'set teredo client' + ENTRY

  j open the Device Manager and the analysis of new hardware.

  k. Select 'Show hidden devices' in the view menu. You will see now that she is present without errors.

  Method 2:

  If the steps above do not help, you can try to uninstall the drivers of the computer network and reinstall and check if that helps. Before uninstalling the network drivers, make sure that you download the latest drivers on the site of computer manufacturers. Follow the steps below to uninstall the network adapter.

  Follow the steps below to uninstall and reinstall the network card.

  a. click on start

  b. in the type of search box of start of "devmgmt.msc" and press enter

  (c) in Device Manager, expand network adapters

  d. right-click on the network adapter and uninstall.

  e. restart the computer, and then reinstall the network card.

  Note: When uninstalling device drivers make sure you put a check mark against 'delete the driver for this device '.

  I hope this helps.

• Drive external hard USB - cela used to work now I get an error message = "this device cannot start. (Code 10) "Any suggestions?

  Drive external hard USB - cela used to work now I get an error message = "this device cannot start. (Code 10) "Any suggestions?

  Hello

  I suggest to refer to this link and follow the steps in this link and check if that helps:

  http://support.Microsoft.com/kb/943104

  It will be useful.

• This device cannot start. (Code 10)

  I accidentally deleted my sound driver and have more noise. the error message im receiving to the IDT codec high definition: this device cannot start. (Code 10)

  Hello

  1. what operating system is installed on your system?

  2. did you of recent changes to the system before the show?

  Method 1:

  Follow the link below and follow the steps and check if it helps.

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Also, check out the link below and see the description of the error code 10.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  Let us know if it helps.

• driver USB 3.0 for HP Pavilion 15 - n210se Windows 7 pro x 64 device cannot start. (Code 10)

  This device cannot start. (Code 10) and show with exclamation point!

  Device ID:

  IUSB3\ROOT_HUB30 & VID_8086 & PID_9C31 & REV_0004 & SID_2166103C

  Hello:

  You need this driver...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-127803-1&cc=us&DLC=en&LC=en&OS=4063&product=6521374&sw_lang=

• Windows live gallery encountered an error loading WLXPhotoViewer.dll and cannot start error code: 0 x 80070035

  Whenever I try to open a picture/photo, I get this message "Windows liver Gallery encountered an error loading WLXPhotoViewer.dll and cannot start error code: 0 x 80070035. Around her, the only is to save the file, then open it with another program. I'm frustrated because this is a nuisance and time-consuming. Any suggestions please?

  Maybe the exclusive database is corrupted.

  Read the following article.

  (944221) freezes Windows Live Photo Gallery
  or does not start
  http://support.Microsoft.com/kb/944221/en-us
  (according to version, database can be
  Pictures.PD4, Pictures.pd5 or Pictures.pd6)

  Rename the Pictures.OLD file will force Live Photo
  Gallery to create a new database on the next launch file.

  Know that the gallery will be as it was the first time that you
  open and some metadata and labels may be lost.

• Cannot access the he DVD drive in Windows Vista. Error: This device cannot start. (Code 10)

  All of a sudden my DVD drive has stopped working. Windows Vista SP2 doesn't see it, but I can see it in the BIOS.
  Error: This device cannot start. (Code 10)
  The driver has the exclamation point. I uninstalled the driver and restarted the PC, but the system does not re - install.
  The exclamation point is up there.

  Help, please

  Thank you

  Hello

  This article can help...

  http://support.Microsoft.com/kb/314060

  Tricky

• Why won't my CD/DVD Slymtype player work, error: this device cannot start. (Code 10).

  Original title: why not my job as a player of DVD/CD of Slymtype at all?
  Here's what I have:

  SlimType DVD C DS24CZP ATA Device

  Windows Vista Home Basic

  Acer aspire 3680 series
  ------------------------------------------
  So here's my problem:

  Recently, I put a DVD disc into the drive. Then, once I closed it, it started to turn, then what sounds like a sound signal, spining, beeps several times, and this will be repeated for a few minutes. Once it stopped, it does nothing. You can not even here it spining. No AutoPlay starts, none Open box, nothing at ALL. The computer doesn't even recognize that there is a DVD in there.

  So, I advanced and found in the Device Manager. The picture showed it was a disc with a CD on top (representing is a DVD/CD player) and in front of it, there was a «!» So I opened the information for it. Here's what he said:

  "This device cannot start. (Code 10) »

  When I try to make windows to search for a solution, it came not with something. I tried to update the driver; no effect. Tried neutralizing him and he the reactivation. No effect. Tried unistalling and restart my computer. When he tries to install it, it fails.

  So now, I did everything I know. Does anyone know how to fix this without having to replace the drive itself? Or should I replace it?

  Thanks in advance!

  Hello

  Did you do changes on the computer before the show?

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104/

  Method 1:
  You can perform the steps in knowledge base article and check:
  http://support.Microsoft.com/kb/982116

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following windows Help article.

  Method 2:
  You can also visit the links:
  Your CD or DVD drive cannot read or write media
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  Hardware devices not detected or does not
  http://support.Microsoft.com/GP/hardware_device_problems