Cisco 2600 router as an IPSec client

Similar Questions

• IOS VPN L2L + C2L (cisco IPSEC client)

  Hello

  need to configure a C2L (client to the LAN) vpn on a cisco router where there is already an ipsec vpn.

  !!! already configured on the ROUTER

  !

  crypto ISAKMP policy 1

  md5 hash

  preshared authentication

  address of cisco key crypto isakmp 0.0.0.0 0.0.0.0

  !

  !

  Crypto ipsec transform-set esp - esp-md5-hmac Tunnel

  !

  crypto dynamic-map 10 Road-Tunnel

  game of transformation-Tunnel

  match address 115

  !

  !

  !

  !

  Crypto map 10 ipsec-isakmp Crypto-Tunnel Dynamic Channel-Tunnel

  !

  point-to-point interface ATM0/1/0.1

  card crypto Crypto-Tunnel

  !

  access-list 115 permit ip 10.0.0.0 0.0.0.255 192.168.168.0 0.0.0.255

  access-list 115 permit ip 10.0.0.0 0.0.0.255 10.2.0.0 0.0.0.255

  access-list 115 deny ip 10.0.0.0 0.0.0.255 any

  !

  !!! new configuration for cisco ipsec client

  !

  no address Cisco key crypto isakmp 0.0.0.0 0.0.0.0

  address of cisco key crypto isakmp 0.0.0.0 0.0.0.0 no.-xauth

  !

  AAA new-model

  !

  AAA authentication login AutClient local

  AAA authorization groupauthor LAN

  !

  !

  username 0 pippo pippo

  !

  crypto ISAKMP policy 10

  BA 3des

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group vpnclient

  key 0-pippo

  DNS 10.10.10.10

  WINS 10.10.10.20

  domain cisco.com

  pool ippoolvpnclient

  Save-password

  ACL 188

  !

  !

  card crypto Crypto-Tunnel client authentication list AutClient

  card crypto Crypto-Tunnel isakmp authorization list groupauthor

  card crypto Crypto-Tunnel client configuration address respond

  card crypto Crypto-ipsec-isakmp dynamic dynmap Tunnel 20

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  match address 188

  Set transform-set RIGHT

  !

  !

  !

  !

  IP local pool ippoolvpnclient 10.99.0.1 10.99.0.30

  !

  access-list 188 note #.

  access-list 188 note # split tunneling VPN C2L

  access-list 188 allow ip 10.99.0.0 0.0.0.31 10.0.0.0 0.0.0.255

  !

  can you tell me if the new configuration is OK?

  Thank you all

  NOT the ACL should be the opposite. Sound from the point of view of the router.

  access-list 188 allow ip 10.2.0.0 0.0.0.255 10.5.0.0 0.0.0.31

  Concerning

  Farrukh

• double authentication with Cisco's VPN IPSEC client

  Cisco VPN client (the legacy IPSEC client) does support dual authentication with RSA token AND ActiveDirectory credentials?

  I know that AnyConnect supports it and the commandsecondary- authentication -Server- group' is only for ssl connections, but must be confirmed.

  Kind regards

  Mohammad

  Hi Mohammad,.

  What is double authentication support for Cisco VPN Client?

  A. No. Double authentication only is not supported on the Cisco VPN Client.

  You can find more information on the customer Cisco VPN here.

  As you said the only client that supports dual authentication is the Cisco AnyConnect secure mobility Client.

  Please note and mark it as correct this Post!

  Let me know if there are still questions about it!

  David Castro,

• Windows 7 32 b ipsec client error 789 RV220W

  Hello

  I'm trying to connect to RV220W with the windows client 7 but I do not see: error 789. I compare new pre shared key, but it doesn't change anything

  Is everyone to connect to RV220W with the IPsec client?

  Thank you

  GF, this isn't a vpn ipsec and he is not so sure. Support only integrated window will be PPTP regarding the connection to the router.

  If you are looking for IPsec, you must use quickvpn (free Cisco software) or a 3rd party software greenbow, shrewsoft, ipsecuritas, etc..

  -Tom
  Please evaluate the useful messages

• Microsoft L2TP over IPSEC client with AES encryption

  I configured L2TP over IPSec Cisco VPN router with Hastings 3des encryption is sha1 with diffie hellman Group 2 and I can't connect with success of Microsoft customers.

  but my question is why can I not connect when I am increasing the encryption with AES 256 and sha256 DH group 14, his looks that windows does not support advanced encryption.

  is it possiple to activate encryption aes with the highest level...? and how?.

  Hello

  To ensure that you get the best response to your concerns, we suggest that publish this request via the Web to Microsoft Developer network site. To do this, visit this link.

  Best regards.

• Cisco 850 routing issues

  I am trying to configure a cisco 850 router but I can't do a ping to the outside world of Vlan1. show running-configLooks follow

  Current configuration : 5563 bytes!! Last configuration change at 15:33:02 UTC Sat Aug 13 2016 by ciscoversion 15.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname fw2.myfw.tld!boot-start-markerboot-end-marker!!logging buffered 51200 warnings!aaa new-model!!!!!!!aaa session-id commonwan mode ethernet!!!ip dhcp excluded-address 10.10.10.1ip dhcp excluded-address 192.168.1.1ip dhcp excluded-address 129.x.x.5!ip dhcp pool ccp-pool import all network 192.168.1.0 255.255.255.0 dns-server 8.8.8.8 8.8.4.4  default-router 192.168.1.1  lease 0 2!         !         !         ip domain name mydomain.tldip name-server 8.8.8.8ip name-server 8.8.4.4ip cef    no ipv6 cef!         !         !         !         crypto pki trustpoint TP-self-signed-1017650632 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-1017650632 revocation-check none rsakeypair TP-self-signed-1017650632!         !         crypto pki certificate chain TP-self-signed-1017650632 certificate self-signed 01  3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030   31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274   69666963 6174652D 31303137 36353036 3332301E 170D3135 30343037 31303536   30375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649   4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 30313736   35303633 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281   81008B15 A50BCE53 C1A10611 78247737 97E31A5D 653AF401 024B244B F96B48E0   0A1B41EE 16FBFDD1 46F2E1E2 1329D2C6 EEFBCF5B 217DE650 7D2729B0 266008F3   AC4565EA 53D7FA5B 35761F14 6FBDCFAC 24994667 CB0311A9 7FE25580 7D9564C3   BFE10A4A F5F57C4F C4E18EC9 19874BCA 03127F56 252D04B8 9465A23F FBB9045B   D9EF0203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603   551D2304 18301680 146EAE54 B0C95DC2 0561F596 BC47E94B EF80617E F9301D06   03551D0E 04160414 6EAE54B0 C95DC205 61F596BC 47E94BEF 80617EF9 300D0609   2A864886 F70D0101 05050003 81810014 F5B63E51 AD80D4A0 3230E94D 3D1BE457   5D7CF78D 3C911F32 C7238D24 4A8C84D5 D5D4F744 EA2FFD5C 4A40E7A1 A517BFE3   10CC6078 5F446A15 F60EA41E 08C688AF A7834485 0991C739 F3CA38FE CFAA31E2   C72031C1 BAEFA756 719E4903 705C98A7 E20CB004 6FC82D22 D4E62E0C DBA54481   F6A68B3D AA905352 DD76B19F CD4190        quit!         !         username cisco password 0 somepasswordusername admin privilege 15 secret 5 $1$JJZR$kw8yTTHkjUGKIfB8sQiyJ0!         !         controller VDSL 0 shutdown !         ip telnet source-interface Vlan1ip ssh port 2222 rotary 1ip ssh source-interface Vlan1ip ssh rsa keypair-name 1024!         !         !         !         !         !         !         !         !         !         !         !         interface ATM0 no ip address shutdown  no atm ilmi-keepalive!         interface Ethernet0 no ip address shutdown !         interface FastEthernet0 no ip address!         interface FastEthernet1 no ip address!         interface FastEthernet2 no ip address!         interface FastEthernet3 no ip address!         interface GigabitEthernet0 no ip address!         interface GigabitEthernet1 description PrimaryWANDesc_WAN interface ip address 129.x.x.5 255.255.255.0 duplex auto speed auto!         interface Vlan1 description $ETH_LAN$ ip address 192.168.1.1 255.255.255.0 ip helper-address 192.168.1.254 ip nat inside ip virtual-reassembly in ip tcp adjust-mss 1412!         ip forward-protocol ndip http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000!         !         ip dns serverip nat inside source list nat-list interface GigabitEthernet1 overloadip route 0.0.0.0 0.0.0.0 GigabitEthernet1!         mac-address-table aging-time 15no cdp run!         !         !         banner exec ^C% Password expiration warning.-----------------------------------------------------------------------
  
  Cisco Configuration Professional (Cisco CP) is installed on this device and it provides the default username "cisco" for  one-time use. If you have already used the username "cisco" to login to the router and your IOS image supports the "one-time" user option, then this username has already expired. You will not be able to login to the router with this username after you exit this session.
  
  It is strongly suggested that you create a new username with a privilege level of 15 using the following command.
  
  username <myuser> privilege 15 secret 0 <mypassword>
  
  Replace <myuser> and <mypassword> with the username and password you want to use.
  
  -----------------------------------------------------------------------^C        banner login ^C-----------------------------------------------------------------------Cisco Configuration Professional (Cisco CP) is installed on this device. This feature requires the one-time use of the username "cisco" with the password "cisco". These default credentials have a privilege level of 15.
  
  YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE  PUBLICLY-KNOWN CREDENTIALS
  
  Here are the Cisco IOS commands.
  
  username <myuser>  privilege 15 secret 0 <mypassword>no username cisco
  
  Replace <myuser> and <mypassword> with the username and password you want to use.   
  
  IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
  
  For more information about Cisco CP please follow the instructions in the QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp -----------------------------------------------------------------------^C        !         line con 0 no modem enableline aux 0line vty 0 4 access-class 23 in privilege level 15 transport input telnet ssh!         scheduler allocate 60000 1000!         end   

  I am connected via the port console of the router and can ping the outside world only from port GigaEthernet1 whose IP address129.x.x.5

  Clients that connect on VLan1 get IP addresses in the range of 192.168.1.0/24 and these clients can ping each other, the gateway that is 192.168.1.1 and the GigaEthernet1 that has the intellectual property129.x.x.5

  What's not in this case?  Any suggestion is appreciated the most.

  @[email protected] / * /;

  Thanks for your post. I had a look at your configuration, and it is great that you are a few short steps on your NAT is why it does not work. Please follow the steps below in order to get this work properly.

  1. first of all, let us remove the old configuration NAT then back to a clean slate with the following commands.

  no ip nat inside source list nat-list interface GigabitEthernet1 overloadclear ip nat translation *

  2. now, we will create a list of access control allows for NAT traffic and create the new NAT statement for that tie together. * NOTE: If the version of IOS, you are running requires mask rather than generic then change 0.0.0.255 to 255.255.255.0.

  access-list 100 permit ip 192.168.1.0 0.0.0.255 anyip nat inside source list 100 interface GigabitEthernet1 overload

  3. the next step is to specify the logical role of the interfaces in question, whether they are 'inside' or ' outside'.

  interface vlan1 ip nat inside exitinterface GigabitEthernet1 ip nat outside exit

  4. Finally, save us the configuration and reload.

  copy run startreload

  After the unit is returned as a result of charging, please try again. In some cases - depending on the version of the IOS, you have to ping the outside world from a computer on the local network rather than just sourcing of the interface VLAN. Try this back and forth, and let me know how get you there. I can't wait to hear back.

  Kind regards

  Luke Oxley

  Please evaluate the useful messages and mark the correct answers.

• IPSEC client 64-bit Vista

  Is there a 64-bit version of the Cisco's IPSEC client on the roadmap?

  I know that there is the AnyConnect client, but that would mean buying more licenses for SSL when we have a lot of IPSEC.

  I understand that there will be no support for it. The only option is to go to AnyConnect.

• IPsec client for s2s NAT problem

  Hello

  We have a remote site (Paris) with a 5512 with some s2s and RA light customer vpn (anyconnect IPsec) tunnels.  AnyConnect has no problem, but the ipsec client can not pass traffic on the LAN.  The subnet behind the fw is 10.176.0.0/16 and the RA 10.172.28.0/24 customer pool.  However, we have a s2s than nat 10.0.0.0/8 tunnel and it appears that customers vpn IPSEC RA being bound traffic matches this rule and prevents connectivity to local resources via vpn ipsec client.

  ......

  hits = 485017, user_data = 0x7fffa5d1aa10, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol

  IP/ID=10.176.0.0 SRC, mask is 255.255.0.0, port = 0

  IP/ID=10.0.0.0 DST, mask is 255.0.0.0, port = 0, dscp = 0 x 0

  input_ifc = inside, outside = output_ifc

  ...

  Manual NAT policies (Section 1)

  1 (outdoor) static source Paris_Network Paris_Network static destination Remote2_LAN_Networks Remote2_LAN_Networks non-proxy-arp-search to itinerary (inside)

  translate_hits = 58987, untranslate_hits = 807600

  2 (inside) (outside) static source Paris_Network Paris_Network static destination DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2-route search

  translate_hits = 465384, untranslate_hits = 405850

  3 (inside) (outside) static source Paris_Network Paris_Network static destination Remote1_Networks Remote1_Networks-route search

  translate_hits = 3102307, untranslate_hits = 3380754

  4 (outside) (inside) static source Paris_RA_VPN Paris_RA_VPN static destination Paris_Network Paris_Network-route search

  translate_hits = 0, untranslate_hits = 3

  This method works on other sites with almost identical configuration, but for some reason, it doesn't work here.  I can't specify different subnets for the s2s tunnel because there is too much of.  Can someone help me and tell me why I can't get this to work?

  Hello

  So you're saying that the AnyConnect is working but not IPsec? What is the the AnyConnect VPN? It is outside the 10.0.0.0/8 network?

  You should be able to substitute the NAT VPN L2L configuration by simply configuring a separate NAT for the local network for VPN pool traffic at the top of your NAT configurations

  For example

  being PARIS-LAN network

  10.176.0.0 subnet 255.255.0.0

  object netwok PARIS-VPN-POOL

  10.172.28.0 subnet 255.255.255.0

  NAT (inside, outside) 1 static source PARIS PARIS - LAN LAN destination PARIS-VPN-POOL PARIS-VPN-POOL static

  This should ensure that the first rule on the SAA is the NAT rule that matches the VPN Client for LAN traffic. Other aircraft in the L2L VPN should still hit the original NAT rule to the VPN L2L

  If this does not work then we must look closer, the configuration.

  Hope this helps

  Remember to mark a reply as the answer if it answered your question.

  Feel free to ask more if necessary

  -Jouni

• 3825 router free for Ipsec

  Hello

  I use Cisco 3825 router with the following version:

  Cisco IOS software, 3800 Software (C3825-ADVIPSERVICESK9-M), Version 12.4 (24) T, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2009 by Cisco Systems, Inc.

  Updated Thursday 25 February 09 22:21 by prod_rel_team

  ROM: System Bootstrap, Version 12.3 (11r) T1, RELEASE SOFTWARE (fc1)

  The availability of R3 is 19 hours 21 minutes

  System returned to ROM of charging at 16:10:58 UTC kills Sep 10 2013

  System image file is "flash: c3825-advipservicesk9 - mz.124 - 24.T.bin".

  What is a clearance for IPSEC features?

  If not,

  Which version I use would you recommend?

  Thank you

  Roee

  Hello Roee, you are all set with this image for the IPsec features.

  Rgds

• Cisco VTI and configuration of IPSec (IKE Phase2) ITS proposal.

  Hello

  I have a question about the functionality of the virtual Tunnel Interface (VTI) configuration option. I have a Cisco IOS router, ending individual customers with the tunnel interfaces. The question I have now is that how can I specify the traffic 'interesting' on the security association proposal ITS IPsec (IKE Phase2). The configuration of the router is made by cryptographic profiles like this:

  !

  crypto ISAKMP policy 10

  BA 3des

  preshared authentication

  Group 2

  !

  Crypto isakmp ISAKMP_PHASE1_PARAMETERS profile

  key ring PRESHARED_KEYS

  function identity address 1.2.3.4 255.255.255.255

  !

  door-key crypto PRESHARED_KEYS

  pre-shared key address 1.2.3.4 key xyz

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac VPN-TRANSFORMSET

  !

  Profile of crypto ipsec ISAKMP_PHASE2_TUNNEL

  game of transformation-VPN-TRANSFORMSET

  PFS group2 Set

  ISAKMP_PHASE1_PARAMETERS Set isakmp-profile

  !

  Tunnel1 interface

  IP 10.10.10.1 255.255.255.252

  IP mtu 1450

  source of tunnel Loopback1

  tunnel destination 1.2.3.4

  ipv4 ipsec tunnel mode

  Tunnel ISAKMP_PHASE2_TUNNEL ipsec protection profile

  !

  Now when I look at the output of the command 'See the crypto ipsec his tu1 int' I get the following:

  ....

  Interface: Tunnel1

  Tag crypto map: x.x.x.x addr Tunnel1-head-0, local

  protégé of the vrf: (none)

  local ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)

  Remote ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)

  current_peer 1.2.3.4 port 500

  LICENCE, flags is {origin_is_acl},

  ....

  However, the peer on the other side do not accept the proposal, as it would like to have specific IP subnets on the IPSec security association proposal parameters. He would accept the policy if the identity local remote proxies, for example, would be 192.168.10.0/255.255.255.0/0/0 (local) and

  192.168.200.0/255.255.255.0/0/0 (remotely).

  Y at - it 'interesting' no IOS configuration for traffic configuration option on the profile of crypto? With the crypto map - basic configuration you can specify interesting traffic with an ACL under the crypto map configuration section.

  I'm in IOS version 15.1 (4) M with Advanced IP Services have together.

  Hello

  ASIT will always want to negotiate a whole as traffic selectors.

  What you MIGHT find is multi-SA DVTI configuration, in what remote end could say what proxy identity he would like to encrypt. (Supported from 15.2 M / T)

  Unfortunately, the ceveat of this configuration is this remote end needs to open the negotiation.

  M.

• Misconfigured remote VPN server by using IPSEC client

  I'm trying to figure out what I did wrong in my setup.  The environment is:

  ASA 5505 running 8.2 with 6.2 ASDM.

  Version of the VPN Client 5.0.05.0290

  I installed VPN ipsec clients both anyconnect and connected successfully to the remote access VPN server. However, the client doesn't show any returned package.  Thinking that I have badly configured, I have reset to the default value of the factory and began again.  Now I only have the configured ipsec vpn and I have exactly the same symptoms.  I followed the instructions to configure the ipsec vpn in Document 68795 and double-checked my setup and I don't know what I did wrong.  Because I can connect to the internet from inside network and I can connect to the VPN from outside of the network (and the ASDM Watch monitor an active connection with nothing sent to the client) I believe this is a road or an access rule preventing communication but I can't quite figure out where (and I tried the static routes to the ISP and a wide variety of access rules before rinsing to start) above).

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal group vogon strategy
  attributes of vogon group policy
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list vogon_splitTunnelAcl
  username password privilege encrypted 0987654321 zaphod 15
  username password encrypted AaBbCcDdEeFf privilege 0 arthur
  username arthur attributes
  VPN-group-policy vogon
  tunnel-group vogon type remote access
  tunnel-group vogon General attributes
  address pool VPN_Pool
  strategy-group-by default vogon
  tunnel-group vogon ipsec-attributes
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:xxxxxxxxxxxxxxxxxxxxxx
  

  Looks like a typo for the Pool of IP subnet mask.

  You currently have:

  mask 10.92.66.10 - 10.92.66.24 255.255.0.0 IP local pool VPN_Pool

  It should be:

  mask 10.92.66.10 - 10.92.66.24 255.255.255.0 IP local pool VPN_Pool

  Please kindly change the foregoing and test, if it still does not work, please please add the following:

  management-access inside

  Policy-map global_policy
  class inspection_default

  inspect the icmp

  Then try to VPN in and see if you can ping 10.92.65.1 and let us know if this ping works.

  Please also share the output of: "cry ipsec to show his" after the trial, if it does not work.

• LAN does not work when the Cisco E1000 router hangs

  Original title: Download sp3

  Remember - this is a public forum so never post private information such as numbers of mail or telephone! I bought recently a new Cisco E1000 router. My computer is a laptop model Lenovo 0769.

  I am running windows XP with sp2. The cisco software requires sp3. I called support of cisco and even they couldn't get to download sp3. My network is wireless on the router and I had to install from another laptop computer on the system. My LAN does not work when hooked. What do you suggest to me.

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hi mdenrique,

  1. what exactly do you mean by LAN (Local Area Network) does not work? You get the error message?

  If you have not installed Service Pack 3, try the following steps:
  Step 1: Download Service Pack 3
  see How to obtain the latest Windows XP service pack .
  b. scroll the window and click on "Download now the Windows XP Service Pack 3 package" to download the service pack.
  c. save the file on the desktop.

  Step 2: Install Service Pack 3
  a. open the file downloaded and follow the instructions in the wizard to complete the installation.
  b. restart the computer once the installation is complete.

  For more information, see steps to take before you install Windows XP Service Pack 3

  Note: Once you have installed service pack 3, install the router and check if the problem persists.

  Step 3: To troubleshoot LAN, run home and small Office Networking Troubleshooter
  a. Click Start and then click Help and Support.
  b. under Pick a help topic, click Network and Internet.
  c. under network and the Web, click on resolution of networking or Web problems and then click on home and small Office Networking convenience store.
  d. answer the questions in the troubleshooter to try to find a solution.

  For more information, see the following articles:
  1 see How to troubleshoot a network in Windows XP
  2 see two resources to solve the problems of connection network in Windows XP

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cisco Wireless router model WRT120N guard give up Internet connection

  My wireless router will work for 6-8 hours, and then remove the connection to the internet.   I switch the modem and the router several times to re-establish the connection.  I'm also using a Netgear Access Point.

  I use:

  Charter high-speed Internet

  Motorola Modem

  Model Cisco WRT120N router

  Parameters

  Mixed-mode

  Channel Auto width - 20 MHz or 40 MHz

  Security - Personal WPA2

  Disabled SSID broadcast

  Firmware Version v1.0.04

  Automatic connection Type - Conf DHCP

  Beacon interval - 50

  Fragmentation threshold 2304

  RTS threshold 2304

  All other settings are default.

  When I unplug the modem to the router and plug it on the desktop I have internet service.

  The connection is also falling only on wired or wireless?

  Try to update the firmware on your router.
  Connect to the computer with the Ethernet cable to the router.
  Download the latest firmware from the site Web of Linksys and save it to your computer. Open the router configuration page. Click the Administration tab and switch to the sub tab upgrade the Firmware through the firmware file that you have already downloaded and update on your router.
  After upgrading the firmware on the router, it is recommended that you must reset the router and reconfigure. Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 10 seconds. Power cycle the router and reconfigure.

• E2500 Cisco's router dual-band

  Hello

  I just install the Cisco E2500 router and set up my wireless network.

  I bought the router hoping it would give me a more powerful than my old G Linksys 2.4 Ghz signal.

  Using inSSider I see my router and unfortunately it seems that both the 2.4 Ghz and 5 GHz range are both at the same time. I need help. The strength of the signal under RSSI is - 60 to-57 for the 2.4 Ghz and 5 Ghz range.

  I have to turn off one of these groups or what should I do to get a stronger signal?... my old Linksys router was to-50.

  Help... I'm not at all intuitive on routers, but I think that I would have only one band at a time or someother setting needs to be changed in order to improve my signal strength.

  Where we cut a band anyway?

  Any help would be appreciated.

  Thank you

  Tom.

  Hi GV Expert,.

  Thanks for your explanation as to what is measured and its relevance.

  I would like to run the test that describe you.

  First; When you say to connect my computer to a single band, I say - would allow a band to achieve this result?

  In addition, how do you transfer a file, we are talking about transfer between my two computers?

  Thank you for your patience and your help.

  Tom.

• Cisco 871 routing problem

  Hello.

  I have a Cisco 871 router with this network diagram

  10.218.10.117 host - 10.218.10.118 4 | CISCO 871 | 172.18.122.5-FE0 - 172.18.122.6 host

  I want the 172.18.122.6 host can do ping to the 10.218.10.117 host at the other end of the router, but its does not work, what is the problem with this config? could someone give me a hand?

  With the help of 1222 off 131072 bytes

  !

  version 12.4

  no service button

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  hostname ALCALÁ-CNT-UIO

  !

  boot-start-marker

  boot-end-marker

  !

  enable secret 5 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

  activate the password XXXXXXXXXXXXXXX

  !

  No aaa new-model

  !

  resources policy

  !

  IP subnet zero

  IP cef

  !

  !

  !

  !

  !

  !

  interface FastEthernet0

  !

  interface FastEthernet1

  !

  interface FastEthernet2

  !

  interface FastEthernet3

  !

  interface FastEthernet4

  IP 10.218.10.118 255.255.255.252

  automatic speed

  full-duplex

  !

  interface Vlan1

  IP 172.18.122.5 255.255.255.0

  !

  router RIP

  redistribute connected

  10.0.0.0 network

  network 172.18.0.0

  !

  IP classless

  !

  !

  no ip address of the http server

  no ip http secure server

  !

  Dialer-list 1 ip protocol allow

  !

  !

  control plan

  !

  !

  Line con 0

  no activation of the modem

  line to 0

  line vty 0 4

  password XXXXXXXXXXXX

  opening of session

  !

  max-task-time 5000 Planner

  end

  Better compliance

  The f

  Jeff,

  Each host can ping their side? You have default gateways configured on the hosts?

  HTH,
  John

  Please note all useful messages *.