Cisco Aironet AP 2700 Series (Autonomuos Mode / stand-alone Configuration)

Similar Questions

• Stand-alone configuration of Cisco Aironet 700i

  Hello

  I'm well aware new products Cisco. So please forgive my basic questions.

  I have Cisco Aironet 700 series AP(AIR-SAP702I-Q-K9). I don't have a controller. I need to set this up as standalone access point.

  I tried all the basic steps and tried to activate the two radios, but no luck. Anyone can guide me please on how to configure the AP.

  I use web access to configure the AP.

  Help, please

  Thank you

  Sagar

  Hi Sam,

  Please check these messages to set up autonomous AP.

  https://rscciew.WordPress.com/2014/05/24/single-SSID-configuration-on-au...

  https://rscciew.WordPress.com/2014/05/24/multiple-SSID-configurations-on...

  Concerning

  Remember messages useful rates

• Stand-alone configuration SX20

  Hello people,

  I'm trying to confugure a SX20 as a stand-alone box, which means that this SX20 will be registered in a CUCM or VCS. I just set up an IP address and get on h323 as static and live mode. However the H323 seems to be inactive. When I try to call to a Polycom, we can make the call. In the diagnostic tool. The diagnostic tool shows the following warning:

  WARNING: Default call Protocol

  The default call protocol is set to H323, but the system is not registered on this Protocol. The system isn't able to make all the calls. Please eitherchange the default call Protocol, verify that Protocol is enabled, or check the configuration H323..
  Could you please help me...
  Thank you!

  Hi Jorge,.

  You can ignore this message because this will show if your devie is not registered on any guard for H323.

  as you use to direct IP to IP call, you h323 is inactive and it will show the above error.

  climbing, you can ignore this message.

• Mode conversion controller in stand-alone mode in cisco 1702

  I have cisco AP 1702 and in controller mode. I don't have the controller so want to convert in stand-alone mode. I went through various items for this and found this interesting way to do.

  Run this command to convert:

  # swarm - Standalone mode
  # reload

  I found this on this link: http://community.arubanetworks.com/t5/Controller-less-WLANs/How-to-conve...

  Similarly, going through the longer process, I downloaded this for the standalone mode: https://software.cisco.com/download/release.html?mdfid=286281141&flowid=...

  and for stand-alone mode, I have this one: https://software.cisco.com/download/release.html?mdfid=286281141&flowid=...

  Here are the files I'm looking for?

  Help, please.

  This original link can cause a headache for an Aruba AP which is different.

  Try this method:

  https://ripplesinharmony.WordPress.com/2013/01/28/downgrading-a-Cisco-lightweight-AP-to-autonomous-mode/

  The software of the first link you posted (https://software.cisco.com/download/release.html?mdfid=286281141&flowid=71622&softwareid=284180979&release=15.3.3-JC1&relind=AVAILABLE&rellifecycle=ED&reltype=latest) will work for the standalone mode (stand-alone).

  This second link is light which means the controller-based and you don't want that for this scenario.

  See you soon,.

  Ric

• Basic questions of configuration Cisco Aironet 1250

  Hello

  I'll be three Aironet 1250 within a building.  It won't be a wireless controller, the AP will be autonomous.  I'll put them all the same thing, with WPA2 wireless encryption.  My question is, what is important and beneficial to add the configuration to the s AP so that they are aware of the other (for roaming maybe)?  If Yes, what is this technology called and someone could direct me to a section of a guide that could illustrate this?

  Or I'm fine with just stand-alone configuration 3 AP as it is.

  All other pointers are welcome.

  Thank you!

  Hello

  If you use the pre-shared as an authentication method, so there is nothing special to do. As long as they have the same SSID, are in the same subnet and are connected to the same network, roaming will be fine.

  No specific configuration is required.

  Nicolas

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• stand alone compact rio

  Hi to everyone!

  I am a student of the University and for my thesis, I use a COMPACT RIO with neither 9205 and gps module, some measures aboard an eletric car, measures will be saved to a TDMS file in the RIO COMPACT by a stand alone configuration and without connection to a pc.

  The compact rio will begins with the car and it will go off with him also.
  So I have a question, how can I stop the VI within the CRIO before turning off the car?  or in TDMS data will be saved in the same way without close the VI within the CRIO before turning off the car?

  Thank you

  Hello antoniolc!

  There is no way of knowing inside CompactRIO, if the system will be shut down.

  You must use an external signal to find out when your car will be stopped.

  Or you can use a multiple TDMS file and like it, just the last TDMS file will be unreadable. But you can probably read all previous TDMS files.

  Best regards.

• Conversion of Cisco Aironet 1130AG light in stand-alone mode

  Hello

  I just bought AIR-LAP1131AG. Unfortunately, I want stand-alone and not lightweight fashion.

  Yes, is there a procedure to convert to "AIR-AP1131AG?

  Thank you.

  Hello Michael,

  Yes, please follow this procedure for TFTP Re-imaging

  / * Style definitions * / table. MsoNormalTable {mso-style-name: "Table Normal" "; mso-knew-rowband-size: 0; mso-knew-colband-size: 0; mso-style - noshow:yes; mso-style-priority: 99; mso-style-parent:" ";" mso-padding-alt: 0 to 5.4pt 0 to 5.4pt; mso-para-margin: 0; mso-para-margin-bottom: .0001pt; mso-pagination: widow-orphan; do-size: 10.0pt; do-family: "Times New Roman", "serif" ;} "}

  1) Go to your Computer and from the tool menu -> folder options ->uncheck the hide extensions for known file types option. 

  2) Download the IOS image ( you can get this ios image from cisco.com) on your desktop.

  3) Rename the image into c1130-k9w7-tar.default

  4) Give your computer Ethernet an address in the range 10.0.0.2 till

  10.0.0.30

  5) Run the tftp server on your computer.

      - Make sure that the directory of your tftp server is the desktop.

      - Specify the AP address on the tftp server if needed.

  6) Connect the AP to the computer with Ethernet cable.

  7) Remove the power from the AP.

  8) Press and hold Mode button on the AP, and insert the power jacket in the AP.

  9) Keep pressing on the Mode button for (20-30 seconds) until you see RED Led.

  10) Wait until the image installed and all led lights return to green 

  doesn't make sure that no firewall or antivrus is running on your computer.

  I hope this helps.

  Kind regards

  Talal

  =============

  Please note the answers that will help you

• Updated standalone Cisco Aironet lightweight mode Access Points

  I'm trying to convert a stand-alone Aironet 1200 in light Mode. I use the tool to upgrade v1.0 proposed by Cisco. But when I put the name of the recovery LWAPP Image (c1200-k9w7 - tar.123 - 7.JA2) in the tool window to update it doesn't work. It is said: c1200-k9w7 - tar.123 - 7.JA2 - LWAPP recovery Image file size is zero. But its size is 4.6 MB!

  Can someone help me?

  Convert the Aironet 1200 of autonomous light mode follow the procedure set out in document http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp23144.

• Only the needs of the Cisco Aironet 1550 series a WLC?

  Hello

  Nice day.  I would like to ask if the Cisco Aironet 1550 series requires a controller to run.  Note that the references SKU in this fomat AIR-CAP1552E-A-K9-AIR-CAP1552EU-A-K9.  I noticed that on the autonomous access point there they keyword 'SAP' on its SKU while the controller based has "CAP".  If the

  Cisco Aironet 1550 Series needs a controller which controller should it be associated? (e.g. AIR-CT2500)

  Thank you

  It can work stand-alone image:

  http://www.Cisco.com/en/us/partner/docs/wireless/access_point/iOS/release/notes/15.2_2_JB.html#wp355908

  1550 relies on:

  2500, 7500, 5508, WISM2,... .etc

  check the release notes of the code controller that you have and you should be able to identify what is supported and what is not supported.

  ----------------------------------------------------------------------------------------------

  Please ensure good answers to rate

• Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  I have (2) AIR-SAP2602I-A-K9, configured the same way.

  on two different remote LANs.

  They don't seem to be handing out addresses via DHCP.

  {If I connect to a local network with another DHCP server}

  wireless devices can obtain addresses

  This another DHCP server on the LAN through the access point.}

  I followed 12.4.25d. JA.cg.pdf

  Configuration of the Access Point to provide the Service DHCP 5-22

  ---------|---------|---------|

  e.g. 3444-RCS1-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS1-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.29.89

  IP dhcp RCS1 pool

  network 192.168.29.88 255.255.255.248

  router by default - 192.168.28.1

  Rental 1 0

  interface BVI1

  IP 192.168.28.211 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.28.1

  ---------|---------|---------|

  ---------|---------|---------|

  e.g. 3444-RCS2-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS2-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.129.81

  IP dhcp RCS2 pool

  network 192.168.129.80 255.255.255.248

  router by default - 192.168.128.1

  Rental 2 0

  interface BVI1

  IP 192.168.128.171 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.128.1

  ---------|---------|---------|

  Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95

  Well this will confuse your customers.

  And this is NOT how to set up your "range".   See below:

  DHCP excluded-address IP 192.168.29.1 192.168.29.87

  DHCP excluded-address IP 192.168.29.96 192.168.29.254

  IP dhcp RCS1 pool

  network 192.168.28.211 255.255.254.0

  router by default - 192.168.28.1

  Rental 1 0

• How to move a stand-alone series C of Cisco UCS managed service profile without losing any data?

  Hello

  We currently have a stand-alone series cisco C with 2012 Windows Server installed on the local disks.  We need to go this Cisco UCS server managed with a service profile, but can not lose existing data and the method of operating system boot.

  Does anyone know how to do this?

  Thank you

  Hi Adrien,.

  To be able to accomplish this together the local drive to 'any Configuration' policy this way UCSM won't overwrite the current raid on the server configuration.

  See the link below

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/SW/GUI/config...

  Let me know if that helps

• Point of access Cisco Aironet 1200 series help

  We have 4 Cisco Aironet 1200 Access Points and they are all set to authenticate with our RADIUS server. However, authentication is hooked and can't understand why. Does anyone have any knowledge/experience with Cisco Aironet 1200 Access Points configuration?

  OK, I do not work with the GUI so although the memory is a little hazy but from the APs home page look on the left hand side and there is an option for something like "Software Setup" or something to that effect. You should be able to find the IOS version of here. This requires that you are indeed runnig IOS code. How old are these APs? If more than a few years ago (and perhaps even more recent) that they could very well be running VxWorks and then we are in a different ball game. If you see what I have described above and the homepage for the AP is often white with a bit of greenish-blue, bluish-green color then IOS, if it is more colorful, yellow stuff and VxWOrks.

  I hope this helps. Let me know if you need anything that anyone else. I will try to answer as soon as POSSIBLE.

• Impossible to find a stand-alone image for Cisco Aironet 1140

  Can someone give a link?

  -JeIlMa

  Here you go:

  http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=IOS+Software&mdfid=282439881&treeName=Wireless&mdfLevel=Model&url=null&modelName=Cisco+Aironet+1140+Access+Point&isPlatform=N&treeMdfId=278875243&modifmdfid=null&imname=&hybrid=Y&imst=N

• Limitation period for H-HARVEST stand-alone mode

  Hello

  We have a customer who is to evaluate a Motorla vs Cisco wireless solution. He said that a Motorola AP can operate in stand-alone mode for 48 hours. He lost after communication to the controller. Is there a limitation like this with a 2500 controller and the solution of access points 1140 series?.

  Y at - it any reference to show?

  Concerning

  Luis Noriega

  Not that I know... but here is a link to the limitation of the h-reap/FlexConnect:

  http://www.Cisco.com/en/us/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html#wp1241304

  http://www.Cisco.com/en/us/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html#wp1229985

  Thank you

  Scott

  Help others by using the rating system and marking answers questions as 'response '.

• Help with a Cisco Aironet 1242AG

  Alright. So, I want to start by saying that I have what I consider to be the basis of knowledge of network management. I recently got a Cisco Aironet 1242AG WAP. I realize that this is not a stand-alone router. I would use it as an extension of my current router. From now on, the status light is alternating colors. If I understand correctly, it can not find the controller. I cannot telnet inside, or use web browser interface. Both say that the connection is not available. However, when I check my DHCP from my router table, I see that an IP address has been assigned to the MAC for the WAP. I tried to do a factory reset holding MODE until I plug the power supply and wait until it turns amber. After a few minutes and go through a few changes led, it goes back to the alternating colors on an ongoing basis.

  I don't really know where to go from here. Help, please.

  Thank you

  Kris

  Radios allow without a ssid that are attached to them. You will need to create your ssid and then fix to the interface radio. assignment of an address to the British Virgin Islands and setting a value default gateway on the device and you should be able to raise it.