Cisco E3000 Cascded Configuration.

Similar Questions

• Cisco E3000 connect Mode cascade

  I have a Linksys E3000 mode cascade with my Modem - Router ADSL. However, even if I can connect using the IP address of the router, I am unable to connect using Cisco connect just in case I want to allow anyone to use the comments feature.

  Can someone tell me how I can connect using Cisco Connect or how to activate the functionality of the web page comments?

  Thank you

  Ocandid

  Yes it will work. If you are still experiencing a problem, you can refer to this link and it will help you in this cascade two routers to each other...

• Cisco Unity Express Configuration 8.6

  We have a Router (3945) CME with CUE 8.6 8.6 (ISM-SRE-300-K9 Module). I have a few concerns about the installation and configuration of CUE.

  1. Cisco ships CUE 8.6 Application preinstalled on ISM-SRE-300-K9 Module?
  2. What is the initial state of CUE in ISM-SRE-300-K9 Module when he left?
  3. To restore CUE setting factory and download/install CUE from scratch?
  4. OR can I directly give the IP interface addresses and go directly to the CUE - GUI?
  5. As I ordered three languages (Arab Saudi, British and English North American) these language packs are available with in the Module when it was shipped? or do I have to download and install?

  ISM-SRE-300-K9	Module (ISM) internal services with Services ready engine
  CON-SAU-ISRE300	SW UPGR + SUPP APP internal Services Module (ISM) with SRE
  SCUE-ISM-8, 6 - K9	Cisco Unity Express version 8.6
  CUE-LANG-ARA	Cisco Unity Express - Saudi Arabic
  CUE-LANG-EN	Cisco Unity Express - British English
  CUE-LANG-ENU	Cisco Unity Express - North American English
  FL-CUE-MBX-5	Unity Express license - 5 mailboxes - CUCM and CUCME
  FL-CUE-IVR-2	Unity License Express - Session 2 IVR
  FL-CUE-PORT-2	Unity License Express - 2 ports
  FL-CUE-NR-PORT-2	Unity Express license 2 - no hostable re - Port

  I have recently installed one of these modules and my experience has been that unit has not come with any software installed.  I had to download and install the software/language packs of cisco.com.

• Router IOS Cisco Anyconnect ASA configuration

  Hello

  Could someone give me some advice if I can use a Cisco 1812 to connect to a Cisco ASA5512X using Anyconnect. The question we have is that some remote offices may be given fixed IP addresses...

  Thank you.

  AnyConnect cannot be used because there is only one solution-client-software and non-integrated IOS as the EzVPN client.

  You can use dynamic cryptographic cards already offered on the ASA with a card standard encryption on the router, or you configure remote EzVPN on the router and on the SAA EzVPN server:

  http://www.Cisco.com/en/us/docs/iOS-XML/iOS/sec_conn_esyvpn/configuration/15-Mt/sec-easy-VPN-rem.html

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/vpn_remote_access.html

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• CISCO 837 VPN Configuration

  Configuration

  my home pc (WIN XP + 4.6.03.0021 VPN Client dynamic IP) ===> internet ===> Corporate (CISCO 837--> LAN + static IP address)

  Hello

  I'm trying to set up a vpn between my pc at home and the CISCO837 company to access the local network.

  I can connect to the CISCO but, I can't access any host on the local network.

  Can someone help me with the basic configuration...

  Homepage:

  Dynamic IP (xxxx.xxxx.xxxx.xxxx)

  Company:

  Address IP WAN (yyy1.yyy2.yyy3.yyy4)

  LAN IP range: (192.168.254.10--> 192.168.254.50)

  Thank you

  Hello..

  1 - when you connect to the Cisco... What is the IP address that you receive from your Cisco VPN adapter. Devices on the local company network need to know how to get back to this IP address.

  Can you please send the configuration of your router 837...

• Windows 7 Home Edition Premium and Linksys E3000 and configuration problems with Dell/Broadcom half mini wireless 1501 wireless adapter DWLAN

  I'be been on the net looking for an answer requarding my Linksys E3000 router and my card adapter Mini PCI Dell/Broadcom DWLAN (DraftN) haf installed on my laptop Dell Inspiron N7010 XL 17 R and the inability to configure the card so he gets the same speed-172 wireless MBps_ as does our HP Vista Home Premium SP2 Laptop and Desktop! Yes, I spoke with Dell who seem to think that all their problems Tech and resolutions can be found with their technicians of the Manila-based Super (Word of warning-do NOT enter into the world of the concierge program of Dell Tech who, after having been assured it is based in the United States, I agreed to be a beta tester and lost my harddrive despite numerous attempts to stop the technicians to access remotely to do stupid things - but the new live Webcam and learn the hard drive but got none of my software original Dell with it as promised, too - another story). In any case, after playing with the DWLAN share of Dell said they question-nope Linksys ' cuz of course my other two computers would be quick at the speed they do. So I get ahold of Comcast, who of course told me, it's a matter of DELL. I have the WPA2 encryption on a network secure, but because my router there is no way to set up a "secure" network guest unless I have disable access to him (seems odd, he says: it is not guaranteed when someone trying to pass over the network, has knowledge password-weird with this router) it is anyway with this mini half DWLAN and the fact that it is not near the speed as the two other wireless adapters. My problem is with the speed I found all kinds of tips for use between Comcast Modem and Linksys router to make your network hum. What I want for now is someone to tell me how to configure this adapter on this Dell computer, so it does the job, it should. I have a program of diagnosis with her and from what I see, I must get off channel 1 as there is too much interference, but before I go and change the settings of the router, I want the adapter to work - especially since it's about 100 Mbps slower than our other wireless adapters. Does anyone know what should be the correct settings for this DWLAN 1501 or that I now need a new adapter in this laptop as well? Thanks for your help.

  LindaSView

  Hi Linda,.

  Have you tried to forget an instant wireless and bypass the router and cable connect directly to the modem to see if you get the speed you want in this way?  Yes, I know that this means to temporarily suspend the internet connection to the local network and also means the creation of a special no wireless connection for this computer.  But it could help determine if the problem is the computer and the router or wireless adapter - which excluding at least.

  If it works fine, then you can pass the wireless problem.  Otherwise, if it is still slow with a direct link, then you may need to consider another problem is involved and the router and adapter can actually be very well and you need to focus on all that is the bottleneck.

  I'm suggesting this to eliminate the possibilities that can be the underlying cause, while you spend your time on the development of bad (although I admit that I think that you are right and it is more likely - it can be useful a test just to be sure).

  Good luck!

  Kosh

• Cisco VTI and configuration of IPSec (IKE Phase2) ITS proposal.

  Hello

  I have a question about the functionality of the virtual Tunnel Interface (VTI) configuration option. I have a Cisco IOS router, ending individual customers with the tunnel interfaces. The question I have now is that how can I specify the traffic 'interesting' on the security association proposal ITS IPsec (IKE Phase2). The configuration of the router is made by cryptographic profiles like this:

  !

  crypto ISAKMP policy 10

  BA 3des

  preshared authentication

  Group 2

  !

  Crypto isakmp ISAKMP_PHASE1_PARAMETERS profile

  key ring PRESHARED_KEYS

  function identity address 1.2.3.4 255.255.255.255

  !

  door-key crypto PRESHARED_KEYS

  pre-shared key address 1.2.3.4 key xyz

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac VPN-TRANSFORMSET

  !

  Profile of crypto ipsec ISAKMP_PHASE2_TUNNEL

  game of transformation-VPN-TRANSFORMSET

  PFS group2 Set

  ISAKMP_PHASE1_PARAMETERS Set isakmp-profile

  !

  Tunnel1 interface

  IP 10.10.10.1 255.255.255.252

  IP mtu 1450

  source of tunnel Loopback1

  tunnel destination 1.2.3.4

  ipv4 ipsec tunnel mode

  Tunnel ISAKMP_PHASE2_TUNNEL ipsec protection profile

  !

  Now when I look at the output of the command 'See the crypto ipsec his tu1 int' I get the following:

  ....

  Interface: Tunnel1

  Tag crypto map: x.x.x.x addr Tunnel1-head-0, local

  protégé of the vrf: (none)

  local ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)

  Remote ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)

  current_peer 1.2.3.4 port 500

  LICENCE, flags is {origin_is_acl},

  ....

  However, the peer on the other side do not accept the proposal, as it would like to have specific IP subnets on the IPSec security association proposal parameters. He would accept the policy if the identity local remote proxies, for example, would be 192.168.10.0/255.255.255.0/0/0 (local) and

  192.168.200.0/255.255.255.0/0/0 (remotely).

  Y at - it 'interesting' no IOS configuration for traffic configuration option on the profile of crypto? With the crypto map - basic configuration you can specify interesting traffic with an ACL under the crypto map configuration section.

  I'm in IOS version 15.1 (4) M with Advanced IP Services have together.

  Hello

  ASIT will always want to negotiate a whole as traffic selectors.

  What you MIGHT find is multi-SA DVTI configuration, in what remote end could say what proxy identity he would like to encrypt. (Supported from 15.2 M / T)

  Unfortunately, the ceveat of this configuration is this remote end needs to open the negotiation.

  M.

• Router Cisco SSL VPN Configuration

  Hello support.

  A question concerning this scenario.

  One of our clients has currently SSLVPN enabled for remote users and I was wondering if there is anyway to configure a remote Cisco router to connect via IPSEC at this endpoint SSLVPN? the idea is simply to set up the tunnel without requiring changes on my end of customers.

  Thanks in advance.

  Ivan Chacon

  Hello

  IPSEC and SSLVPN are 2 different configurations, there is no way to have a router configured for IPSec and connect to another without changing this end as well.  You can run IPSec and SSLVPN on the same router, however.

  There are a lot of IOS Lan to Lan configuration guides, or if you want the router to act as a client, are looking to make EZVPN.

  HTH

  -Jason

• 5510 Cisco can be configured to make dns relay?

  Hello

  My client uses the public dns, but they do not want dhcp to give public DNS dns. They want him to point on firewall, then only one firewall before the public DNS dns. Would it be possible for ASA 5510?

  Kind regards

  Hing

  Hing,

  So-you can configure a static on the SAA statement that will correspond to the IP address of the DNS.  For example:

  public static 10.1.1.253 (exterior, Interior) 1.1.1.1

  You must also ensure that traffic UDP 53 is also allowed via your inside interface access list.  On your DHCP server, then you re 10.1.1.253 as your DNS server IP address - in reality, the ASA will result simply the real 1.1.1.1 that IP address.

  Hope this helps,

  Kevin

• Cisco ASA 5505 - Configuration VPN

  I'm trying to configure a VPN connection to allow customers access to the internal network. I have tried to use time Wizard VPN & repeatedly but customer connect but can get out to the internet and communicate with any host on the network. I tried to use a vpn in the 192.x.x.x or 10.10.1.X network dhcp pool but no luck.

  Comments or suggestions appreciated.

  What is the reason for these commands?

  NAT (outside) 0-list of access policyPAT

  NAT (outside) 5 10.10.1.0 255.255.255.0

  If this isn't spicific reason remove

  and put the following command:

  Permitted connection ipsec sysopt

  in global configuration mode to enable the VPN traffic to work around interface access lists

  Good luck

  If useful rates

• E3000 Router Configuration cascade

  I have the game following up in a home in Brooklyn, NY:

  Your solution worked perfectly!  It is now work!  Thanks a lot for your help.

• configuration cisco air-ap1142n-a-k9 problem wpa2 wireless access point

  HI people,

  I am brand new to Cisco Wireless, just that I bought new wireless access point air-ap1142n-a-k9 cisco, try to configure the configuration of wpa2 for security reason, but impossible to configure in any mode security. So my AP is currently no security / encryption mode.

  Could someone can help and suggest me I will appreciate if I get all documents, so the security problem can be solved.

  Concerning

  Sanjeev

  OK great

  ----------------------------------------------------------------------------------------------------------------------

  Be sure to note the correct answer and mark the thread as answered

• Impossible to establish a VPN connection with a router configured as a Cisco server using client VPN 5.0.00.0340

  Hei guys,.

  Please help me on this one because I'm stuck enough on her...

  I am trying to connect to a Cisco 3700 router configured as a VPN server by using a VPN client and the VPN connection does not settle.

  This is an extract from the log:

  130 12:48:30.585 07/01/11 Sev = Info/5 IKE / 0 x 63000001
  Peer supports XAUTH
  131 12:48:30.585 07/01/11 Sev = WARNING/3 IKE/0xE3000057
  The HASH payload received cannot be verified
  132 12:48:30.600 07/01/11 Sev = WARNING/2 IKE/0xE300007E
  Failed the hash check... may be configured with password invalid group.
  133 12:48:30.600 07/01/11 Sev = WARNING/2 IKE/0xE300009B
  Impossible to authenticate peers (Navigator: 904)
  134 12:48:30.600 07/01/11 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: INVALID_HASH_INFO) for 200.100.50.173

  I enclose the whole journal extract... The message "BOLD" is quite obvious, you mean, but I'm 100% sure, in the login entry, I typed correctly the group password: pass

  My topology is very basic, as I am setting this up only to get a clue of the operation of the Cisco VPN. It is built in GNS3:
  -2 3700 routers: one of them holds the configuration of the VPN server and the other would be the ISP through which the remote worker would try to establish a VPN connection. I am also attaching the configuration file for the router configured as a VPN router.

  Behind the second router there is a virtual XP machine on which I have installed VPN client...

  My connection entry in the customer is to have the following parameters:
  Host: 200.100.50.173 , //which is the IP address of the VPNServer
  Authentication-> authentication-> name group: grup1 password: pass / / I'm quite positive that I typed the correct password... even if the log messages are linked to a misidentification.

  I use public addresses only, because I noticed there is a question about behind the NAT VPN connections and is not not very familiar to the NAT.

  Another aspect which can be of any importance is that "allow Tunneling of Transport" in the tab Transport to the input connection is disabled

  and the VPNServer router logs the following error message when you try to establish the connection:

  * 01:08:47.147 Mar 1: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE 200.100.50.34 package was not encrypted and it should have been.
  * 01:08:47.151 Mar 1: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE 200.100.50.34 package was not encrypted and it should have been.
  

  You have no idea why I can't connect? Y at - it something wrong with my configuration of VPN server... or with the connection entry in the VPN client?

  Thank you

  Iulia

  Depending on the configuration of the router, the group name is grup1 and the password is baby.

  You also lack the ipsec processing game that you would need to apply to the dynamic map.

  Here is an example configuration for your reference:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080235197.shtml

  Hope that helps.

• Configure Cisco ASA VPN client

  I did some research and the answers it was supposed to be possible, but no info on how to do it.  I wonder if it is possible to configure a Cisco ASA 5505/10/20 to be a customer to an existing (in this case) cisco vpn client.  The reasons why are complicated (and irrelevant IMO), but basically, I need to be able to make a small network that may be on this vpn rather than on individual computers.

  The vpn client is a Basic IPSec over UDP Cisco VPN to an ASA5505.

  So, how to set up an another ASA to connect to it as if it were a client?

  Hello

  Here is a document from Cisco on the configuration, the easy ASA of VPN server and Client

  Although in this case, they use a PIX firewall as a client.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805c5ad9.shtml

  Here's another site with instructions related to this installation program

  http://www.petenetlive.com/kb/article/0000337.htm

  I imagine that the site of Cisco ASA Configuration Guide documents will also give instructions how to configure it.

  -Jouni

• Browser access to E3000

  I have a Linksys E3000 wireless router. It works fine, but I want to see its settings. When I was with my old XP machine, I could connect to my router using Firefox to http://192.168.0.1 and see or change the settings, I've wanted to. Then I got a new desktop computer with Windows 7 64-bit (no wi - fi on it). I withdrew my old XP machine. I don't have reinstall my Cisco s/w. My wireless router still works fine. But I can't have my E3000 via my browser (Firefox) using this IP address. All I get is the message to reset the connection.

  My E3000 is configured as an access point. I have other wireless devices, connection, but not my new machine W7. My network is configured as network, Internet access type.  I use Trend Micro Titanium.

  How can I connect to my router now that I'm on W7 64-bit?

  If you opened to the top of the router configuration page when connecting the computer with BEFSR81 router
  If this is the case then connect the computer on the E3000 router. Check the IP address and default gateway, then try to open the configuration page of the router with the default gateway...

  You can search for the IP address and the default gateway in the following way:

  Click on the Start button...
  Select all programs accessories---> it will be all see guest...
  The type there "ipconfig"...