Cisco Network Assistant 5.5

Similar Questions

• Cisco Network Assistant

  Hello

  Anyone know how really peripheral can be added in the community and manage through CNS version 6? I read on the website of cisco that Cisco Network Assistant can support up to 40 aircraft in the community, I don't know if it was for the previous ANC 5.0 version as shown in the link http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/network-assistant/product_data_sheet0900aecd8068820a.html for switches 40 or less while watching in the version 6.1 of the ANC data sheet , he also mentions the community limiting to 40 devices while the following link http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/network-assistant/datasheet-c78-730210.html shows that for switches 40 or less. Will be looking forward to seeing the answers.

  Thank you

  Waydee

  Hi Waydee

  Please refer to the for Cisco Network Assistant Release Notes 6.0 and later versions , where you can find all of the changes. In summary the community limits are same (max 40) compared to the old version (5) of the CNA.

• Cannot connect Cisco Network Assistant to 2911 router

  I'm trying to connect my Cisco 2911 router to my community at the NAC.  I can see the routers in terms of topology, but when I try to add to the community I get an error message indicating that the router is inaccessible (cannot connect).  I can ping client device of soul. I can view the properties of the device to the card (device type: CISCO2911/K9). Telenet attempt connection, but we have only use SSH for connectivity (the same as all my switches that are connected to the community).  2911 is listed as a taken router supported on the Cisco site.

  Any quesses what I am doing wrong?

  Thanks in advance.

  J

  Hello
  You must enable http for can work.

  http://kirkpbm.WordPress.com/2008/07/13/Cisco-network-assistant-enabling...
  Pls link for other instructions above check.

  Rgds/DP
  Sent by Cisco Support technique iPad App

• ISE 1.4 and Apple 'captive Network Assistant"causing problems

  I'm testing ISE 1.4 with 10.10.2/Safari 8.0.3 MAC and the boring revised downward Safari AKA "Captive Network Assistant" gets in the way.  I wonder what other people did to work around.

  According to the compatibility of network component Cisco ISE v1.4 Safari I must be compatible, in captivity Network Assistant says that this isn't, but I suspect its because the computer MAC laptop try to validate with ~ 200 areas (so I hear for this).  My ISE/WLC have a DACL that allows certain IP addresses before finishing the AuthC/Z, and obviously I can't put in the DACL for all 200 of these areas.  My ISE is configured with trustsec model where I have two SSID, a first on the front-end to detect if Anyconnect 4.x is installed and if it is not then redirect to a portal.  Fails it MAC peripheral security check cause... or should I say will not display it. cause Apple Network Assistant captive.

  I know I can disable the captive Network Wizard by renaming the file, but it will probably not an acceptable solution in my environment for political reasons.  I wonder what others have done to bypass this annoying problem.  Maybe something with a DNS record or something...

  Thank you

  e-

  Common recommendation is to deceive the apple devices to think he has access to the internet by running this command on the command-line of your WLC:

  config network web-auth captive-bypass enable

• In the Windows Installer box - insert Dell network Assistance

  original title: Windows Installer box.

  Windows Installer box - message says:

  "The feature you are trying to use is on a CD-ROM or another removable disk that is not available.  Insert the disc "Dell network Assistance.

  I don't know which disk i.e. - any ideas.

  Occurs when I try to open MS Word or something in the office.

  WORKED FINE YESTERDAY

  Help

  Hello

  ·         This only happens when you use Office applications?

  Try to reinstall network of Dell since the Dell software came with the computer and check if this is useful.

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Help with M6348 connecting to a Cisco network

  Hello

  Can someone help me with best practices by putting R710 via a M6348 stacked with a cisco network.

  Our configuration is the following

  M1000e

  2 x 1 GB pass-through fabric a

  2 x M6348 wired in a pile in the B fabric

  6 x popular R710 with four NIC ports in the fabric B (3 are general purpose servers, 3 are Hyper-V servers in a cluster)

  Cisco network

  For most of the Cisco 3560 switches

  20 VLAN (1 per building) configured, mainly for the isolation of traffic (VLAN 300-320)

  What (I think) that we want to

  The M6348 connect to the core network in a SHIFT (4 x 1 GB ports. Can it be divided 2 ports each of the stacked M6348?)

  Have a mapping of right for 1-3 to VLAN 301 R710

  Configure R710 4-6 for access to all VLANS for the Hyper-V hosts can be placed on the VLAN correct

  Use the fabric for the connection to the San

  Network management is carried out by a third party (we are unable to change this) and they claim that they are unable to connect Cisco/Dell!

  We are server guys, guys network no, so something stupid (especially for Cisco to give to our management company) would be appreciated.

  We tried to configure the switches in Simple mode, using a Dell deployment guide, but all we seem to get is the default VLAN to all ports on the switch 1 battery, but no other VLAN and no active port 2 in the stack.

  I've probably missed lost info on and were not very clear, so if more info is needed, please get back to me.

  Thanks in advance for the help

  Rich

  Thanks for the information updated, actually, this confirms that the problem is with the connection to the Cisco switch. Is that what we tried a general link, instead of trunk?

  mode console # switchport general

  Console # switchport General allowed vlan add 300-320 tag

  Console # pvid General switchport 301

  Console # end

  Are we sure that the VLAN 301 IP address is 10.49.56.0? This doesn't seem fair.

  When we try to pings on the trunk/General connection to the Cisco switch, make sure you that the servers have the default gateway defined on the VLAN IP address they are in access mode. Thus, when in the access mode VLAN 301 the gateway server would need to be 10.49.56.0. I would like to verify that the IP address, however.

• Dell network Assistant

  Network Assistant Dell expired after 90 days. I now get a wizard repair network popup window every few minutes telling me that the network is connected, it is very annoying. How to stop? What I have to buy a $39.95 from Dell program or is there a simple solution?

  
  

• No reports of Cisco network

  I have not received e-mails that connects to the network over a week reports. Everyone knows this?

  Thank you very much

  ambergris77 wrote:

  I have not received e-mails that connects to the network over a week reports. Everyone knows this?

  Thank you very much

  Hi ambergris77,

  Call the Network Magic Support and ask them. I agree is more for them. Scott Taylor, who made the reports, is no longer with Cisco.

• WAP4410N existing other than Cisco network gateway

  Hello

  I was wondering if someone can quickly answer my question?

  I am trying to use my WAP4410N to create a wireless bridge to an existing network that does not contain any Cisco kit. After reading the manual, I tried the bridge WDS wireless solution, which is my router wireless D-Link & MAC address, but there is no option to put in network WPA2 key, I guess I misunderstood how this feature works, & maybe it works with other products of Cisco wireless?

  Thanks in advance to anyone who can shed light on my question,

  Andy

  Sent by Cisco Support technique iPhone App

  HI Andy,.

  Noramlly that configure you WDS Bridge would need to implement WPA 2 personal option under the wireless part, and then click Security.

  Since the SSID and security must be the same, is that were you would enter information. As to make this set your work with a D-Link wireless router, you'll never miss that probably the question were that this wireless device must support WDS. Even then you might also encounter a question having no match wireless chipsets as well.

  More than likely that this configuration will not work for you. I advise to use an other WAP4410n to establish the connection. Rely on what you are wanting to do a WET200 may also work for you since its just fill a wireless network and only use WDS, but I have never tested this connection with a D-link router so I can't 100% guaranteed if this implementation will work as well or not.

  Hope this helps and let me know if you have any questions.

  Thank you

  -Clayton Sill

• map of Cisco network topology first Infrastructure

  Hi just want to ask if it is possible to create a map of the network topology of edge of the main cisco which shows the cable devices and wireless infrastructure, or do we need another cisco product to accomplish.

  Thank you

  Hello

  Topology service is not supported in 2.0 IP, however, it is in the road map.

  for the support and the function of the comparison, you can check out the link below:

  http://www.Cisco.com/en/us/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html

  Thank you-

  Alya

  [Note the useful post]

• Network Assistant will not connect pc to the LAN, but connect to the internet properly

  My main PC had been connected to a local network of four PC but abruptly dropped from the network.  I can connect to the internet OK, but the wizard does not reconnect me to the local home network.  I read other articles on test and checks and everything seems to be okay, but when I check my network places other computers are running and are not displayed.

  Try the following and see if it helps:

  "You can not access the shared files and folders or browse computers in the workgroup with Windows XP"
    <>http://support.Microsoft.com/kb/318030 >

  HTH,
  JW

• LaserJet 2100 direct connect network assistance

  Hello techies.  I need help please.

  I have a HP Laserjet 2100 printer with a Jetdirect 600n (J3110A) card I am using with my plug for laptop Compaq V2615US as a direct connection.  It is without a server between the computer and the printer.

  Has been fighting for more than a week. Time for me to reach and ask for help.

  It is not recognized.

  Print a page of Cofiguration Jetdirect info I get the following information:

  LAN HW address: 001083F3A247

  External Loopback 03 error is NOT READY i/o card

  TCP/IP STATUS: 55 CURRENT BOOTP/DHCP

  HOST NAME: NPIF3A247

  IP address: 0.0.0.0

  IPX/SPX STAUUS: impossible to 29 net number of senses

  NAME OF THE NŒUD: NPIF3A247

  I was able to CLEAR the error of closure by doing a loopback plug.

  Using the network printer wizard I tried individually enter either the host name, IP address, LAN HW or name of the node above the address in the appropriate box.  NONE of them worked.

  Somewhere, I saw a reference to a supposed "default" IP address of the 192.0.0.192.  Tried it as an IP address, nothing helps. Received a message on the screen indicating that it was a 'default' address and suggesting that it was not fair.

  My computer's network card is a Realtek 8139/810 x Family card that is declared as working correctly by my computer and has already been used in the past in this way with a different printer.

  Key questions are:

  1 what I'm missing or doing wrong?

  2 - is a dead Jetdirect card?

  I can access a Jetdirect 620n card, but the application list I've seen doesn't have the list of the 2100 as a printer there.

  It would be worth to try myself to a substitution of the 620n for my 600n card?

  Thanks in advance for your help.

  John

  "LittleJohn1969" wrote in message News: * e-mail address is removed from the privacy * .com...

  Hello techies.  I need help please.

  I have a HP Laserjet 2100 printer with a Jetdirect 600n (J3110A) card I am using with my plug for laptop Compaq V2615US as a direct connection.  It is without a server between the computer and the printer.

  Has been fighting for more than a week. Time for me to reach and ask for help.

  It is not recognized.

  Print a page of Cofiguration Jetdirect info I get the following information:

  LAN HW address: 001083F3A247

  External Loopback 03 error is NOT READY i/o card

  TCP/IP STATUS: 55 CURRENT BOOTP/DHCP

  HOST NAME: NPIF3A247

  IP address: 0.0.0.0

  IPX/SPX STAUUS: impossible to 29 net number of senses

  NAME OF THE NŒUD: NPIF3A247

  I was able to CLEAR the error of closure by doing a loopback plug.

  Using the network printer wizard I tried individually enter either the host name, IP address, LAN HW or name of the node above the address in the appropriate box.  NONE of them worked.

  Somewhere, I saw a reference to a supposed "default" IP address of the 192.0.0.192.  Tried it as an IP address, nothing helps. Received a message on the screen indicating that it was a 'default' address and suggesting that it was not fair.

  My computer's network card is a Realtek 8139/810 x Family card that is declared as working correctly by my computer and has already been used in the past in this way with a different printer.

  Key questions are:

  1 what I'm missing or doing wrong?

  2 - is a dead Jetdirect card?

  I can access a Jetdirect 620n card, but the application list I've seen doesn't have the list of the 2100 as a printer there.

  It would be worth to try myself to a substitution of the 620n for my 600n card?

  Thanks in advance for your help.

  John

  Without any kind of switch between the printer and the computer, you absolutely have a cable modem Simulator for your connection "ethernet".  You will NOT be able to use a standard ethernet cable.
   
  Once you find this crossover cable and that you ran a test on the printer print to the default IP address (read the printer or jet direct instructions on the card to print or otherwise find the Jetdirect card settings) then you can create a new "printer port" using the IP address of the card direct jet to join the two.    192.0.0.192 isn't usually an IP address by any device (I've never seen anywhere.)  It would more likely be something like 192.168.1.xxx.
   
  Also, you should be able to buy a switch 4 ports and do the same thing with standard ethernet cables.  Plug the computer and jet direct card printer on the switch.

• Network Assistant unable to finish the configuration of network domestic

  I'm trying to set up a network using the wizard, whenever I try to use the created dsc (Firewall window files are corrupt and cannot reset) I use Win XP on all computers. Firewall off

  There is no need to use the created disc.  Run the Configuration Wizard from the network on each computer by clicking on its icon in Start > all programs > Accessories > Communications . Boulder computer Maven
  Most Microsoft Valuable Professional

• Cisco Configuration Assistant?

  Hello guys,.

  I am trying to download a CCA software but you should know what type of account, I need to download?

  Partner, comments or other?

  We have a vanuty URL: www.cisco.com/go/configassist

  The most recent is 2.2 (4).

  You should be able to get as a registered partner, I think...

  Steve

  Sales of small businesses

• SG 300-Cisco Configuration Assistant

  Hi guys, I'm unable to connect a SG 300 alternate with CCA v3.2. I have already connected the switch with CCA, but I see nothing in my CCA façade and topological.

  Here's the view my view front once I have connected the switch:

  

  Could be he you guys please help me to find out what is the problem?

  Thank you very much!

  Hello Michel,

  Have you been able to connect with CCA before? In addition, is the switch on the latest firmware?