Client VPN connects but not internal LAN access or Ping

Similar Questions

• AnyConnect VPN connected but not in LAN access

  Hello

  I just connfigured an ASA to remote VPN. I think everything works but I do not have access

  for customers in the Local LAN behind the ASA.

  PC <==internet==>outside of the SAA inside<=LAN=> PC

  After AnyConnect has established the connection I can ping inside the Interface of the ASA

  but I can't Ping the PC behind the inside Interface.

  Here is the config of the ASA5505:

  : Saved

  :

  ASA Version 8.2 (1)

  !

  asa5505 hostname

  activate 8Ry2YjIyt7RRXU24 encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 192.168.178.254 255.255.255.0

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  Shutdown

  !

  interface Ethernet0/3

  Shutdown

  !

  interface Ethernet0/4

  Shutdown

  !

  interface Ethernet0/5

  Shutdown

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  Shutdown

  !

  passive FTP mode

  Inside_ICMP list extended access permit icmp any any echo response

  Inside_ICMP list extended access permit icmp any any source-quench

  Inside_ICMP list extended access allow all unreachable icmp

  Inside_ICMP list extended access permit icmp any one time exceed

  access-list outside_cryptomap_2 note ACL traffic von ASA5505 zur ASA5510

  outside_cryptomap_2 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0

  no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0

  no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.178.0 255.255.255.0

  tunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  mask 192.168.1.10 - 192.168.1.15 255.255.255.0 IP local pool SSLClientPool

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access no_NAT

  NAT (inside) 1 192.168.1.0 255.255.255.0

  Access-group Inside_ICMP in interface outside

  Route outside 0.0.0.0 0.0.0.0 192.168.178.1 1

  Route outside 192.168.10.0 255.255.255.0 192.168.178.230 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA authentication http LOCAL console

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set-3DESSHA FRA esp-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  card crypto outside_map 2 match address outside_cryptomap_2

  peer set card crypto outside_map 2 192.168.178.230

  card crypto outside_map 2 game of transformation-FRA-3DESSHA

  outside_map interface card crypto outside

  Crypto ca trustpoint localtrust

  registration auto

  domain name full cisco - asa5505.fritz.box

  name of the object CN = cisco - asa5505.fritz.box

  sslvpnkeypair key pair

  Configure CRL

  Crypto ca certificate chain localtrust

  certificate fa647850

  3082020b a0030201 30820174 020204fa 0d06092a 64785030 864886f7 0d 010104

  0500304 06035504 03131763 6973636f 617361 35353035 2e667269 2d 3120301e a

  747a2e62 6f783126 30240609 2a 864886 f70d0109 02161763 6973636f 2d 617361

  2e667269 35353035 747a2e62 6f78301e 170d 3132 31303132 31383434 31305a 17

  323231 30313031 38343431 06035504 03131763 6973636f 3120301e 305a304a 0d

  617361 35353035 2e667269 747a2e62 6f783126 2a 864886 30240609 f70d0109 2D

  6973636f 02161763 2d 617361 35353035 2e667269 747a2e62 6f783081 9f300d06

  d6279e1c 8181009f 092a 8648 86f70d01 01010500 03818d 30818902 00 38454fc 9

  705e1e58 762edc35 e64262fb ee55f47b 8d62dda2 102c8a22 c97e395f 2a9c0ebb

  f2881528 beb6e9c3 89d91dda f7fe77a4 2a1fda55 f8d930b8 3310a05f 622dfc8f

  d48ea749 7bbc4520 68 has 06392 d65d3b87 0270e41b 512a4e89 94e60167 e2fa854a

  87ec04fa e95df04f 3ff3336e c7437e30 ffbd90b5 47308502 03010001 300 d 0609

  2a 864886 04050003 81810065 cc9e6414 3c322d1d b191983c 97b474a8 f70d0101

  2e5c7774 9d54d3ec fc4ee92d c72eef27 a79ce95a da83424f b05721c0 9119e7ea

  c5431998 e6cd8272 de17b5ff 5b1839b5 795fb2a0 2d10b479 056478fa 041555dd

  bfe3960a 4fe596ec de54d58b a5fa187e 5967789a a26872ef a33b73ec 7d7673b9

  c8af6eb0 46425cd 2 765f667d 4022c 6

  quit smoking

  crypto ISAKMP allow outside

  crypto ISAKMP policy 1

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  localtrust point of trust SSL outdoors

  WebVPN

  allow outside

  SVC disk0:/anyconnect-win-2.3.0254-k9.pkg 1 image

  SVC disk0:/anyconnect-wince-ARMv4I-2.3.0254-k9.pkg 2 image

  enable SVC

  tunnel-group-list activate

  internal SSLClientPolicy group strategy

  attributes of Group Policy SSLClientPolicy

  VPN-tunnel-Protocol svc

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split tunnel

  the address value SSLClientPool pools

  WebVPN

  SVC Dungeon-Installer installed

  time to generate a new key of SVC 30

  SVC generate a new method ssl key

  SVC request no svc default

  username password asdm privilege Yvx83jxa2WCRAZ/m number 15

  hajo 2w8CnP1hHKVozsC1 encrypted password username

  hajo attributes username

  type of remote access service

  tunnel-group 192.168.178.230 type ipsec-l2l

  IPSec-attributes tunnel-group 192.168.178.230

  pre-shared-key *.

  type tunnel-group SSLClientProfile remote access

  attributes global-tunnel-group SSLClientProfile

  Group Policy - by default-SSLClientPolicy

  tunnel-group SSLClientProfile webvpn-attributes

  enable SSLVPNClient group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:0008564b545500650840cf27eb06b957

  : end

  What wrong with my setup.

  Concerning

  Hans-Jürgen Guenter

  Hello Hans,.

  You should change your VPN pool to be a different subnet within the network, for example: 192.168.5.0/24

  Then configure NAT exemption for traffic between the Interior and the pool of vpn.

  Based on your current configuration, the following changes:

  mask 192.168.5.10 - 192.168.5.15 255.255.255.0 IP local pool SSLClientPool

  no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0

  And then also to enable icmp inspection:

  Policy-map global_policy

  class inspection_default

  inspect the icmp

• VPN connects but no remote LAN access

  Hello

  I'll put up on a PIX 501 VPN remote access.

  When I try to connect via VPN software, I am able to connect but I am unable to access LAN resources.

  I have pasted below part of which seems relevant to my setup. I'm stuck on this issue, could someone help me? Thanks in advance.

  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  test.local domain name
  name 10.0.2.0 inside
  name 10.0.2.13 MSExchange-en
  2.2.2.2 the MSExchange-out name

  outside_access_in tcp allowed access list all gt 1023 host 2.2.2.2 eq smtp
  outside_access_in list access permit tcp any host 2.2.2.2 eq https
  outside_access_in list access permit tcp any host 2.2.2.2 eq www
  inside_outbound_nat0_acl 10.0.2.0 ip access list allow 255.255.255.0 192.168.235.0 255.255.255.192
  access-list 101 permit icmp any one

  3.3.3.3 exterior IP address 255.255.255.0
  IP address inside 10.0.2.254 255.255.255.0
  IP local pool vpn_pool 192.168.235.1 - 192.168.235.15
  IP local pool vpn_pool_2 192.168.235.16 - 192.168.235.40

  1 3.3.3.4 (outside) global
  NAT (inside) 0-list of access inside_outbound_nat0_acl
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  static (inside, outside) 2.2.2.2 10.0.2.13 netmask 255.255.255.255 1000 1000
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 3.3.3.1 1

  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS (inside) host 10.0.2.3 * timeout 10
  AAA-server local LOCAL Protocol

  Permitted connection ipsec sysopt
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto-map dynamic dynmap 10 game of transformation-ESP-3DES-MD5
  map outside_map 90-isakmp ipsec crypto dynamic dynmap
  card crypto outside_map the LOCAL RADIUS client authentication
  outside_map interface card crypto outside
  ISAKMP allows outside
  part of pre authentication ISAKMP policy 20
  ISAKMP policy 20 3des encryption
  ISAKMP policy 20 md5 hash
  20 2 ISAKMP policy group
  ISAKMP duration strategy of life 20 86400
  vpngroup signal address vpn_pool pool
  vpngroup dns-server 10.0.2.3 signal
  vpngroup default-field test.local signal
  vpngroup idle time 1800 signal
  vpngroup max-time 14400 signal
  signal vpngroup password *.
  vpngroup TF vpn_pool_2 address pool
  vpngroup dns-server 10.0.2.3 TF
  TF vpngroup default-domain test.local
  vpngroup TF 1800 idle time
  vpngroup max-time 14400 TF
  TF vpngroup password *.

  Kind regards

  Joana

  Very similar to the question of the configuration of the switch. You should check if there is no specific roads on the switch outside the default gateway. The switch should route the subnet pool ip to the firewall (10.0.2.254).

• Ipad Cisco ipsec VPN connects but not access to the local network

  Hi guys,.

  I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.

  If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.

  Cisco 877.

  My config is attached.

  Any ideas?

  Thank you

  Build-in iPad-client is not useful to your configuration.

  You have three options:

  (1) remove the ACL of your vpn group. Without split tunneling client will work.

  2) migrate legacy config crypto-map style. Here, you can use split tunneling

  3) migrate AnyConnect.

  The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.

• Client VPN connects but no IP traffic is passed...

  I have a user in a hotel, his laptop was works well on remote connections previously, he gets the lock when it connects, but no IP traffic is passed. Is it pings it gets "host unreachable". I think he's behind a firewall of hotel, but nothing else that I can check to confirm? I was going to put the new client available for download (internet access works very well), he performs a version 4.7. I also tested his connection on a profile box test and it worked fine.

  UM... so it is able to authenticate so I don't think that he coulkd be blocked... double check you are using have traversed nat enabled on your PIX...

  ISAKMP nat-traversal 20

  I hope that helps... Rate if he does!

• Client VPN connects but cannot ping all hosts

  Here is the configuration of a PIX 501, which I want to accept connections from the VPN software clients.  I can connect successfully to the PIX using the 5.0.0.7.0290 VPN client and I can ping the PIX to 192.168.5.1, but I can't ping or you connect to all hosts behind the PIX.  Can someone tell me what Miss me in my setup?

  Thanks for your help.

  Chi - pix # sh conf
  : Saved
  : Written by enable_15 at 03:49:39.701 UTC Friday, January 1, 1993
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate the encrypted password
  encrypted passwd
  hostname chi - pix
  .com domain name
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol they 389
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  list-access internet-traffic ip 192.168.5.0 allow 255.255.255.0 any
  Allow Access-list allowed a whole icmp ping
  access-list 101 permit ip 192.168.5.0 255.255.255.0 10.10.11.0 255.255.255.0
  access-list 102 permit ip 192.168.5.0 255.255.255.0 10.10.11.0 255.255.255.0
  pager lines 24
  opening of session
  debug logging in buffered memory
  ICMP deny everything outside
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside pppoe setroute
  IP address inside 192.168.5.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  IP local pool ippool 10.10.11.1 - 10.10.11.254
  PDM logging 100 information
  history of PDM activate
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) - 0 102 access list
  NAT (inside) 1 list-access internet-traffic 0 0
  group-access allowed to ping in external interface
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set esp - esp-md5-hmac GvnPix-series
  Crypto-map dynamic dynmap 10 GvnPix-set transform-set
  toGvnPix 10 card crypto ipsec-isakmp dynamic dynmap
  toGvnPix interface card crypto outside
  ISAKMP allows outside
  ISAKMP key * address 0.0.0.0 netmask 0.0.0.0
  ISAKMP keepalive 60
  ISAKMP nat-traversal 20
  part of pre authentication ISAKMP policy 9
  encryption of ISAKMP policy 9
  ISAKMP policy 9 md5 hash
  9 2 ISAKMP policy group
  ISAKMP policy 9 life 86400
  vpngroup address ippool pool chiclient
  vpngroup dns 192.168.5.1 Server chiclient
  vpngroup wins 192.168.5.1 chiclient-Server
  vpngroup chiclient com default domain
  vpngroup split tunnel 101 chiclient
  vpngroup idle 1800 chiclient-time
  vpngroup password chiclient *.
  Telnet 0.0.0.0 0.0.0.0 inside
  Telnet timeout 30
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 30
  management-access inside
  Console timeout 0
  VPDN group chi request dialout pppoe
  VPDN group chi net localname
  VPDN group chi ppp authentication pap
  VPDN username password net *.
  dhcpd address 192.168.5.2 - 192.168.5.33 inside
  dhcpd dns xx
  dhcpd rental 86400
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 100
  Cryptochecksum:
  Chi - pix #.

  On the PIX configuration seems correct.

  I guess you try to access hosts in 192.168.5.0/24, and these default hosts is the PIX inside interface 192.168.5.1?

  How you try to access these internal hosts? If you try to ping the hosts, please please make sure there is no personal firewall enabled inside welcomes as personal firewall normally doesn't allow incoming connections from different subnet ip address.

• Cisco vpn client to connect but can not access to the internal network

  Hi all

  I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network

  Any help would be much appreciated.

  Hi Samir,

  I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (The link above includes split tunneling, but this is just an option.

  Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.

  Let me know if this can help,

  See you soon,.

  Christian V

• I am trying to create a VPN connection, but it does not work

  I am trying to create a VPN connection, but it does not work
  The wizard cannot establish a connection. And if I try to record simply does not connect
  It does not work. If I try to click on find the problem, there simply
  do nothing.
  I tried it on another pc, where it worked. So the problem is not the
  router or data network. And the curious thing is that I installed it before, but only from one day to the other, the VPN connection was missing.

  It does not create even a the connection icon
  Thank you

  Try a system restore to a Date before the problem began:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  See you soon.

  Mick Murphy - Microsoft partner

• VPN connected but no visible network

  so I have a windows 7 (VPN server) desktop computer and a windows laptop 7 (VPN client) and I have set up the incoming VPN connection on my desktop and a client VPN connection on my laptop. When I go and establish a VPN connection, it says that I'm connected on my laptop and my desktop but I can't access my network resources. Ive been cracking as a result for a few weeks now and have gotten nowhere with it, any help would be greatly appreciated. Thank you!

  I can't access something like \\ServerName\ShareName I can't do a ping them either. address ranges are not the same on the server or client networks. the funny this is that it says I am connected at both ends, the customer declares that ipv4 has no internet access on the vpn which is fine because all I want is access to the network and it shows that I have an ip address assigned on the vpn map. side server but it is said that ipv4 and ipv6 are not connected, but if I do "ipconfig/all" he shows me his ip address on the vpn.

  client side, I've disabled 'Gateway on remote network use default' so that I can still have access to the internet on the im client that is connected to the vpn. on the side server, I tried selecting "Assign addresses automatically using DHCP" as well as "specify IP addresses (with a beach which is on the client and the server ip address range).» I have also "Allow the calling computer to specify its own IP address" selected on the server.

  When I finally fell a VPN server on a Vista box I got the address assigned to the configuration of clients like that.

  http://theillustratednetwork.MVPs.org/Vista/PPTP/VPNSetup06.jpg

  The address range was the same that the server of the LAN address range, in this case, I used 192.168.10.X on the local network.

  http://theillustratednetwork.MVPs.org/Vista/PPTP/ExampleVistaVPNNetwork.PDF

  Customer recevrait.31 ou.32...

  Of course assumed that the customer was or would not be on a LAN 192.168.10.X to start. If it was so I could have problems connecting to shares on my LAN Server.

  MS - MVP Windows Desktop Experience
  "When all else fails try what the captain suggested before you started...". »

• Customer Cisco PIX 501 VPN connects but no connection to the local network

  Hi all:

  I am able to make a VPN connection to a PIX 501. The remote client is assigned an IP (192.168.2.1) also, but not able to access all the machines in the local network connected to the PIX.

  I have attached the PIX configuration.

  Advice will be greatly appreciated.

  ********************

  6.3 (5) PIX version

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxxx

  pixfirewall hostname

  domain ciscopix.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  access-list 102 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool ippool 192.168.2.1 - 192.168.2.5

  location of PDM 192.168.2.0 255.255.255.0 outside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) - 0 102 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup vpn3000 ippool address pool

  vpngroup vpn3000 Server dns 68.87.72.130

  vpngroup vpn3000-wins 192.168.1.100 Server

  vpngroup vpn3000 split tunnel 101

  vpngroup vpn3000 downtime 1800

  password vpngroup vpn3000 *.

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:xxxx

  ****************

  The DNS server is the one assigned to me by my ISP.

  My internal network connected to the PIX is 192.168.1.1 - 192.168.1.33 and the VPN ip pool is 192.168.2.1 - 192.168.2.5

  "isakmp nat-traversal 20" can do the trick.

• I am trying to create a VPN connection, but when I get to the step that allows me to create the VPN, the radial buttons are greyed out.

  I am trying to create a VPN connection, but when I get to the step that allows me to create the VPN, the radial buttons are grayed out, it is a Windows component is missing and does not allow me to create VPN. I am running Windows XP Home addition. I recently got a Malware attack and had the quarantine and fix trojen attempts. After the restoration, I found that my previous VPN connection was broken. When I tried to add a new connection, I'm stuck on the screen connection virtual network in the the radial button private network connection wizard is grayed out, he could not check.

  Hello

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Windows XP TechNet forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en/itproxpsp/threads

• My laptop connects is more to the internet, either hard wired or wireless. When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.

  My laptop connects is more to the internet, either hard wired or wireless.  When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.  My other computer has service very well (or I wouldn't send this message) I checked everything, what to do?

  original title: internet connection.

  Hi vonhatten,

  1. Did you the latest changes on the computer?
  2. You receive an error message when you try to connect to the internet?
  3. You have security software installed on the computer?

  Refer to the article below and try the steps mentioned, check if it helps.

  In Windows network connection issues

  http://support.Microsoft.com/kb/313242

• E4200 Mac connects but not PC after crash

  We had a power failure.  Connection Wi - Fi disturbed and has not corrected itself as in the past.

  A MAC and android os phone will connect but not PC with different operating systems.

  Wired computers will connect and go on the internet but not when try wireless on windows PC.

  I have a comcast modem and a router wireless e4200.

  Tried the re-engining of the modem and the router.

  Tried to unplug Cisco on computers and then reconnect to wireless connection.

  Sometimes laptops will discover the excellent show and Cisco of the signal power but does not connect.

  Wireless is enabled on laptop computers.

  Do not know what has changed this causes for the victory of the PC only.  (IP? etc?)

  Any help is appreciated.

  Thank you.

  Thank you for the answers.

  I did a factory reset within the connection on the router.

  After resetting my settings it works fine.

  No idea what scattered settings.

• I created a vpn connection, but can I create a shortcut to connect every time?

  I created a vpn connection, but can I create a shortcut to connect every time?

  I created a vpn connection, but can I create a shortcut to connect every time?

  Open network and sharing Center, go to the Edit card settings window and drag the VPN icon on your desktop.

• connected but not connected

  Hello
  on 11g on HP UNIX.
  
  Can not understand: connected but not connected:

  sqlplus sys@+ASM as sysdba
  
  Enter password:
  ERROR:
  ORA-12154: TNS : 
  Enter user-name: sys as sysdba
  Enter password:
  Connected.
  SQL> select * from v$instance;
  select * from v$instance
  *
  ERROR at line 1:
  ORA-01012: not logged on

  Any idea?
  Thank you.

  sqlplus sys@+ASM as sysdba
  ORA-12154: TNS:
  Enter the user name: sys as sysdba

  SQL > select * from v$ instance;
  Select * from v$ instance
  *
  ERROR on line 1:
  ORA-01012: not connected

  You connect to the instance by TNS connect descriptot ASM?
  Which alert log file shows?

  tnsping + ASM