Closed network communicates not problem

Similar Questions

• Home network problem: 0 x 80070035: network path not found.

  I have problems with my home network; my laptop is unable to access the files on my HTPC

  More precisely:

  Laptops and PCs are running Windows 7 Ultimate. My laptop is connected to the home wireless network, the PC is connected through the LAN. Router is a Netgear DG834GV. Both computers have fixed IP addresses. They are part of the standard workgroup workgroup. There was formerly a group residential, put in place, which worked very well. We also have a Vista laptop that does all the unusual problems. Until a few days ago, the whole Setup worked perfectly. I could previously access/copy/distribute multimedia content, play on the PC via Zune music on my laptop and print from my laptop to the computer, but now I am unable to do one of these. The other laptop still works fine.
  From the network on the PC screen, I can see the files from the laptop and access.

  However, since the network on the computer screen laptop, I see the PC, but when I try to open it I get the error "Windows could not access \\MEDIACENTER. 0 x 80070035 the network path was not found. "I ping the PC with the IP address and name, and I can even remote to the computer desktop.

  ipconfig on the laptop did something funny...

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Card tunnel Local Area Connection * 139:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Card tunnel Local Area Connection * 143:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Card tunnel Local Area Connection * 140:

  ... up to 200. I can't that assume it goes back to #1 as well.

  After a few suggestions on here I just went through the enable netbios over TCP/IP, but now I can't see even the PC! Still can ping and access internet tho.

  Any suggestions as to what may be the cause?

  Here is the solution for "error code 0 x 80070035 network path not found" on Windows Vista and Windows 7 computers. Click on the button 'START', select 'CONTROL PANEL' and go to 'DEVICE MANAGER'. Click on "NETWORK CARDS", then click on 'VIEW' and select 'SHOW HIDDEN DEVICES'. In the expanded view, you will see a long list of numbered "MICROSOFT 6to4 ADAPTER". My Windows 7 Professional Office had 200 of them. Right click and select 'DELETE' on all but 1 of them. You can only do 1 at a time, so it takes some time. When you have only 1 left, restart the computer and enjoy being able to see the other computers on your network, including the RESIDENTIAL group files.

• Problem with searching for computer on the network. Error: "unable to browse the network. The network is not present or not started. »

  Hello

  I have two NICs connected to my computer for creating hotspot Wifi network. I created successively network Wi - Fi hotspot. But after that when I tried to connect to my local network computers
  My network places-> network-> network Microsoft Windows. I get this error "unable to browse the network. The network is not present or not started. »
  Thank you.

  I am able to fix this by myself.

  The solution that worked for me:
  Run as administrator command prompt.
  Insert the Windows XP Sp3 CD in disc drive (I have xp sp3 installed)
  
  At the command prompt, type in
  
  
  SFC/SCANNOW
  
  
  
  

• Bluetooth network is not available

  Been trying for a while to use AirDrop on my MacBook Pro (Version OS X El Capitan 10.11.6) and my iPhone 6 s more.

  Just realized today that it might not work because the Bluetooth on the Pro does not work. With each device I try a pairing, it says that the network is not available and that I need to make sure that network access is enabled. Trying to do this, system preferences > network > Bluetooth PAN, I get the same message. I need you to ensure that network access is enabled.

  Someone else had this problem? Any ideas on how to solve it?

  Open system preferences > Bluetooth. Make sure that Bluetooth is enabled.

• Comments on Time Capsule network does not

  I recently installed and configured my new Time Capsule (TC) and created my home network, that works without problem. The guest network distributes however, 169 IP addresses to any device connected to it. My TC has the following parameters:

  Internet: Connect using DHCP, IPv4 address: 192.168.0.10, Internet Options configure IPv6: link-local, wireless: welcome and feedback network enabled with both wireless security WPA/WPA2 Personal, wireless Options: not used, network: router Mode: Off (Bridge Mode). I tried to use DHCP and NAT (distributes 172 IP address for iPhone and iPad and internet work), but my TC light flashes orange and the home network is not working correctly. What is the correct Assembly and my home and guest network can work properly? Thanks for your help!

  Network: Router Mode: Off (Bridge Mode).

  The prompt will not work with the TC in bridge.

  I tried to use DHCP and NAT (distributes 172 IP address for iPhone and iPad and internet work), but my TC light flashes orange and the home network is not working correctly.

  It of the right mode for wireless guest... but is the wrong way for the TC, because then you have double NAT.

  Reset you the TC to plant before you set up or do you exchange you bridge DHCP and NAT... If the later, it won't work... you must first factory reset.

  In my humble OPINION Apple made a stupid decision to prevent comments in mode bridge... but you can't change it.

  The bridge is the right settings for the TC... you use the wireless on the main router as a guest... wireless or you should fill the main router in order to use the TC as the only router.

• I can access network, but not the internet.

  I am able to access my network but not the internet.  However, I can get on the internet if I use parallels.  Does anyone else have this problem? If so, how have you managed to solve.  I rebooted without parallels and nothing changes.  Any suggestions?

  In the menu bar, you select

   ▹ System Preferences... ▹ ▹ ▹ Advanced TCP/IP network

  What values are given for the following?

  Configure IPv4

  IPv4 address

  Subnet mask

  Router

• Recently closed tabs does not work for me

  Recently closed tabs does not work for me. When I go to history-> recently closed tabs is not available and the shortcut does not work. It happened a few weeks ago, and when it happened first, the shortcut would open the tabs in the weeks earlier. I can't find any information on this and would like to see it fixed.

  There are other things that need your attention on the updated the prefs that shows in your list of details of the system.

  Reset the general.useragent.compatMode.firefox to false, and all prefs network.http on the topic: config page.

  • http://KB.mozillazine.org/about:config

  What is the value of the browser.sessionstore.max_tabs_undo pref?

  • http://KB.mozillazine.org/browser.sessionstore.max_tabs_undo
  • http://KB.mozillazine.org/browser.sessionstore.max_windows_undo

• I can connect to the local network, but not to the internet

  Why in an internet connection, I can connect to the Local network, but not to the Internet.
  I have valid IP address and configuration is good.

  I recommend you read some threads here in the forum about similar issues.
  If this problem occurs using the WiFi network, then check if you can use the connection to the local network.
  Using the WiFi network, you must check if the common WLan parameters are favourable;
  Check if the encryption key is right; turn off filtering by mac address, check the TCP/IP protocol settings if it has been set to automatic, disable the firewall settings, rest you WLan router, check if you connected to the right SSID.

  Good bye

• My Satellite L850-A921 closed and could not start

  I have my laptop closed and did not start again even with problems different shoots:
  -You press the power button for more than 15 seconds, but no response
  -A out the battery and the power supply lead for 20 minutes and then plug in the power again, no response
  -Used battery alone, no response
  -No response or any signal / light on the laptop

  Any help is very appreciated,

  Kind regards
  SC

  Your motherboard is dead or one or two modules of memory are defective.
  If new modules of RAM don t help you, I guess that the motherboard must be replaced.
  :(

• "the settings saved on this network do not match the network requirement" is the message that I get when I try to connect to my wifi

  I changed my router to another wireless.  Since then, my laptop cannot connect to my wifi.  When I search my wireless network, it is exed out in red.  and the message "the settings saved on this network do not match the network requirement"... Please help

  [moved from comments]

  Hey Mike,

  -What version of Windows is installed on the computer?

  This problem usually occurs with wireless networks. I suggest you try the suggestions in http://answers.microsoft.com/en-us/windows/forum/windows_vista-networking/the-settings-saved-on-this-computer-does-not-match/a82432f2-9312-480a-b2ea-720033c73387

  Let us know if this can help, or if you have any questions.

• Wireless network is displayed with a cross and will not let me connect saying the settings for this network do not match the requirements of the networs and it is a hidden network how to make it visible again?

  hardware device

  my wireless network is displayed with a cross and will not let me connect saying settings for this network do not match the requirements of the networs and it is a hidden network how to make it visible again :(

  Hello

  What operating system installed on the computer?

  Note: Look for errors in the network card device manager.

  Method 1: Follow the article mentioned below, if you are using Windows 7 operating system.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2:

  He looks at the IP address and other parameters are not set correctly, I suggest you contact your Internet service provider or provider router wireless to help on this.

  For more information, follow the below mentioned article:

  Set up a wireless router:

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  Follow the below mentioned articles and see if they help you:

  Set up a wireless network:

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  Wi - Fi and in Windows network connection issues:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Wireless network card: frequently asked questions:

  http://Windows.Microsoft.com/en-us/Windows7/wireless-networking-frequently-asked-questions

• Whenever I try to start the media player, it was closed due to a problem.

  Original title: windows media player

  Whenever I try to start the media player, it was closed due to a problem.

  Hello

  (a) you receive an error message?

  (b) when was the last time it was working fine?

  (c) you did any hardware changes or software on your machine before this problem?

  (d) what operating system do you use?

  Method 1: I suggest to try the steps in the link below and check if this can help:

  Troubleshooting of Windows Media Player settings (it applies to Windows 7)

  http://Windows.Microsoft.com/en-us/Windows7/open-the-Windows-Media-Player-settings-Troubleshooter

  Method 2: Try to solve this problem with boot.

  See the following Microsoft KB article:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Hope this information is useful.

• Network Pro K8600 problems

  Hello

  We had a problem with the k8600. Theres no possible connection on the network. Indicates the configuration page:

  http://169.254.246.85

  IP 169.254.246.85

  ..

  Default gateway: 0.0.0.0

  Configuration Suorce: Auto IP

  It is of course a random IP address, but how can I change this without having the opportunity to reach the printer (on the browser or something else

  The LEDs for the network (green, not flashing yellow flashing when the printer starts up then off)

  The printer works with USB

  Could someone help us?

  Thanks a lot for your help!

  solved the problem

  Connect a laptop to the

  changed the laptop computer ip address for 169.254.246.1 / 255.255.0.0.
  then got a connection with the browser

  changed the IP for the network of the company

  hope this helps someone else

• Once I changed my ISP my computer network does not work and does not recognize my router lynsys

  Once I changed my ISP my computer network does not work and does not recognize my router lynsys

  Hi George,.
  Please go to the Microsoft Community Forums.
   
  1. do you get an error message?
  2. do you have the internet connection wired or wireless?
  3. What is the brand and model of the computer?
   
  I suggest to refer to the links and follow the steps in the articles:
   
  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help?T1=Tab03#network-problems=Windows-XP&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1
   
  Resources for the resolution of the problems of modem in Windows XP
  http://support.Microsoft.com/kb/308022#top
   
  How to troubleshoot wireless network connections in Windows XP Service Pack 2
  http://support.Microsoft.com/kb/870702
   
  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357#appliesTo
   
  If the problem persists, contact the Internet service provider for assistance.
   
  I hope this helps.

• Example: Pavilion ac123tx: hosted network does not start

  in my computer hp laptop ac123tx (preloaded with win 10 OS) not able to start the wifi hotspot because it lacks the virtual network adapter hosted Microsoft. I tried to start the hosted network from cmd prompt, but every time it gives message hosted network could not be started. The group or resource is not in the correct state to perform the requested operation. what need have the solution to this?

  Hello @gbnavapara,

  Thank you for visiting the HP Forums! The Forums are a great place where you can find solutions for your problems, with the help of the community!

  I read your post about the WiFi problem and wanted to help you!

  Have you tried activation of the adapter in the Device Manager?  You can use the resources here to help: difficulty The Hosted network could not be started in Windows 10 error

  (Not a HP website supported).

  Also, you can try to update your network drivers.  If you're still having problems, then try to review the measures offered in the following post:

  Re: Microsoft organized virtual adapter network - this device is not connected to the computer

  Let me know how it goes.  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great weekend!