closure of incomplete cycle

Similar Questions

• Buffer the output AO, refresh rate is different from the sample clock frequency

  Hello

  I am an AO output in the buffer using a single channel. I have a stamp with a ripple of 200000 points with a triangular waves of a 1000pts each repeated 200 times. If I want a frequency of 1 Hz, I simply update this waveform 1000pts and if I wanted to 5 Hz, then 5000pts and so on. But there is some frequency that I won't be able to use like the refresh rate (the number of samples that I ask to update) is different from the sample clock frequency, which makes synchronization with the other difficult to trigger (incomplete cycle).  Frequency 3 Hz (update 3000pts), as (update 7000pts) 7, 6 Hz (update 6000pts), 9 (update 9000pts)... 11Hz at 15 Hz and is not valid in the sense that the refresh rate is different from the sample clock frequency. That makes a whole lot of inaccessible CONFIGURED!  Can someone tell me what determines the banned frequency?  Is this something to do with the material?

  concerning

  One thing you can try is to change the number of samples per cycle. This cannot give the precise frequency accurately, but can reduce the average error.

  120 Hz, the error is currently about 400 parts per million (ppm). The accuracy of the time base is 50 ppm, then this error is less than 10 times the inherent error due to the time base.

  Consider this configuration: the closest nominal sampling you rate, you can get is 120048 Hz (1000 samples per cycle at 120 Hz). If your buffer contains 1200 samples per cycle, 100 copies of it would produce 1 second of data to 120,048 Hz. But if the buffer contained an average of 1200,48 useful Samper by cycle, you get the exact frequency.  Of course getting 0.48 of a sample is delicate. But the kind of feasible. If you use 48 cycles in the 1201 samples per cycle and the cycles of 52 to 1,200 samples per cycle, the total number of samples per second = 120048. Average frequency will be exactly what you want. Instantly, the frequency is slightly higher or lower than the exact value.  By an alternation of 1200, 1201, 1200, 1201... 1201, 1200 100 cycles that the Jig is fast.  If you group all 1200s whole and all 1201 s frequency hopping may be more sensitive.  If this kind of jitter is acceptable depends strongly on what you do with the release.

  This technique is used in some systems of frequency synthesizer.

  Lynn

• adoption of Patching EBS R12.2 error

  Hi all

  EBS R12.2.4

  RHEL6.6

  phase of adoption $ [appcrp@ip-10-0-0-216 MobileApps] = apply patches = 20049473 patchtop = / u01/MobileApps

  Enter the password for APPS:

  Enter the password:

  Enter the password for WLSADMIN:

  Please wait. Validating credentials...

  RUN the file system context: /u01/appcrp/CRP/fs1/inst/apps/CRP_ip-10-0-0-216/appl/admin/CRP_ip-10-0-0-216.xml

  Context file system PATCH file: /u01/appcrp/CRP/fs2/inst/apps/CRP_ip-10-0-0-216/appl/admin/CRP_ip-10-0-0-216.xml

  Run the SYSTEM command: / u01/appcrp/CRP/fs2 df

  Determination of worker of County...

  Successful validation. All are called nodes are listed in the table ADOP_VALID_NODES.

  [EVENT]     [EARLY 2015/03/20 19:29] Mental health of high-performance database controls

  [EVENT]     [END 2015/03/20 19:29] Completed the database sanity checks

  [UNEXPECTED] Apply the phase cannot be performed in a fixed cycle, i.e. after prepare phase.

  Log file: /u01/appcrp/CRP/fs_ne/EBSapps/log/adop/adop_20150320_192839.log

  [STATEMENT] Run adopscanlog utility, by using the command

  "adopscanlog-latest = yes".

  for a list of the log files as well as the snippet corresponding to each log file error message.

  adopted out with status = 2 (failure)

  [appcrp@ip-10-0-0-216 MobileApps] $ adopscanlog-latest = yes

  Analyzing the log u01/appcrp/CRP/fs_ne/EBSapps/log/adop/adop_20150320_192839.log file...

  /U01/appcrp/CRP/fs_ne/EBSapps/log/adop/adop_20150320_192839.log:

  ----------------------------------------------------------------

  #(27-31) lines:

  [PROCEDURE] [EARLY 2015/03/20 19:29:01] Staging of the current session

  [PROCEDURE] [END 2015/03/20 19:29:01] Staging of the current session

  [UNEXPECTED] Apply the phase cannot be performed in a fixed cycle, i.e. after prepare phase.

  [PROCEDURE] [EARLY 2015/03/20 19:29:01] Unlock sessions table

  [STATEMENT] Unlock ad_adop_sessions table for ip-10-0-0-216 with wait 60 seconds interval and number of tent 2

  =============

  [ec2-user@ip-10-0-0-216 ~] $ vi /u01/appcrp/CRP/fs_ne/EBSapps/log/adop/adop_20150320_192839.log

  Log file: /u01/appcrp/CRP/fs_ne/EBSapps/log/adop/adop_20150320_192839.log

  [EARLY 2015/03/20 19:28:40] Arguments passed to adoption

  phase = patch = 20049473 patchtop = / u01/MobileApps

  [END 2015/03/20 19:28:40] Arguments passed to adoption

  [EARLY 2015/03/20 19:28:40] Check the settings

  [END 2015/03/20 19:28:58] Check the settings

  [STATEMENT] Sourcing of the editing of run environment: /u01/appcrp/CRP/fs1/EBSapps/appl/APPSCRP_ip-10-0-0-216.env

  [EVENT]     [EARLY 2015/03/20 19:28:59] Verification of the requirements of ENV

  [EVENT]     [END 2015/03/20 19:29] Verification of the requirements of ENV

  [STATEMENT]  With the help of 4 workers (default: 4, recommended maximum limit: 62)

  [PROCEDURE] [EARLY 2015/03/20 19:29] Determine the admin node

  [STATEMENT] Node admin: "ip-10-0-0-216.

  [PROCEDURE] [END 2015/03/20 19:29] Determine the admin node

  Successful validation. All are called nodes are listed in the table ADOP_VALID_NODES.

  [EVENT]     [EARLY 2015/03/20 19:29] Mental health of high-performance database controls

  [EVENT]     [END 2015/03/20 19:29] Completed the database sanity checks

  [PROCEDURE] [EARLY 2015/03/20 19:29:01] Acquisition of a lock on the sessions table

  [STATEMENT] Locking ad_adop_sessions table for ip-10-0-0-216 with wait 60 seconds interval and the number of tent 2

  [PROCEDURE] [END 2015/03/20 19:29:01] Acquisition of a lock on the sessions table

  [EVENT]     [EARLY 2015/03/20 19:29:01] Check that the waiting for sessions

  [PROCEDURE] [EARLY 2015/03/20 19:29:01] Control assets /hotpatch session

  [STATEMENT] Fetch the number of incomplete cycles for ip-10-0-0-216 with appltop_id = 195.

  [STATEMENT] value of incomplete_session: "0".

  [PROCEDURE] [END 2015/03/20 19:29:01] Control assets /hotpatch session

  [STATEMENT] Master Session ID: UNDEFINED

  [PROCEDURE] [EARLY 2015/03/20 19:29:01] Staging of the current session

  [PROCEDURE] [END 2015/03/20 19:29:01] Staging of the current session

  [UNEXPECTED] Apply the phase cannot be performed in a fixed cycle, i.e. after prepare phase.

  [PROCEDURE] [EARLY 2015/03/20 19:29:01] Unlock sessions table

  [STATEMENT] Unlock ad_adop_sessions table for ip-10-0-0-216 with wait 60 seconds interval and number of tent 2

  [PROCEDURE] [END 2015/03/20 19:29:01] Unlock sessions table

  
  

  ==============

  
  

  [appcrp@ip-10-0-0-216 ~] $ adop-status

  Enter the password for APPS:

  Current patch ID of Session: 3

  Name of node node Type Phase status started completed elapsed

  --------------- --------------- --------------- --------------- ------------------------------ ------------------------------ ------------

  CRP2 slave FS_CLONE COMPLETED 5 November 14 03:59:33 - 04:00 November 5, 14 04:54:56 - 04:00 0:55:23

  PREPARE NOT APPLICABLE

  APPLY NOT APPLICABLE

  COMMISSIONING DON'T IS NOT APPLICABLE

  CLEANING DON'T IS NOT APPLICABLE

  Folder synchronization system used in this Patching Cycle: full

  For more information, run ADOPTION Status Report using - option detail

  Generating the ADOPTION status report to the location: /u01/appcrp/CRP/fs_ne/EBSapps/log/status_20150320_194359/adzdshowstatus.out

  Please wait...

  Done...!

  Please see

  ORA-20001: unable to set editing ORA-06512: has the jump "APPS.ad_zd" job: egosdaci.sql on the appsad_zd build (Doc ID 1989739.1)

  https://support.Oracle.com/epmos/faces/PatchDetail?RequestId=18488991&_afrLoop=191137541272365&patchId=20183051%3AR12.ego.D&_afrWindowMode=0&_adf.CTRL-State=5jicoeb2j_165

  AppsMAsti
  sharing is caring

• HP dv9000 Power Up Cycling

  My HP Pavilion dv9308nr notebook PC will try to power for about 20 seconds (all of the lights on) and then stop for about 1 second then repeat the cycle.

  Regardless of the stop mode.  Strangely enough, it almost never happens time, probably 9 out of 10.

  There are TWO ways to get out of this cycle.

  1. quickly press the F10 key at initial startup which stops at the stop after 20 seconds. The screen remains black. I usually wait more than 20 seconds to ensure that the closure is not the case. THEN, turn off the power switch. WAIT 5 seconds. Turn on the power switch. The PC start just as it is supposed to.

  2. turn the power switch. Unplug the charger. Remove the battery. Waiting (I usually it give 20-30 seconds). Install the batteries. Install the charger. Turn on the power switch. The PC start just as it is supposed to.

  Any body got a fix for this problem?

  Followed my problem a little.

  Other symptoms began to appear on my system which were:

  Once the system has been started successfully, it would operate normally during various periods of time and then freeze - the iconcs could be turned on but neither the keyboard, touchpad, or external mouse would respond. To recover, I would go through the same procedure as described above.

  I had read about a problem with the cooling on the HP Pavilion all and installed heat sync SPECCY of PIRIFORM on this system to monitor operating parameters. Among the readings showed the CPU operating between 60 and 65 degrees celsius and the graphics GeForce operating between 80 and 85 degrees. My research listed these in normal limits, so I ignored it even if I thought that it seemed too hot.

  I finally bought a motherboard renovated with synchronization of heat changed with additional cooling fins.

  Installed card mother and everything works fine.

  Temperatures? CPU 40 - 45 degrees celsius and graphics 60-65 degrees celsius, a cooler on each lot of 20 degrees.

  Heat my original problem? OR was there another hardware problem?

  GISH! I do not know.  I am running normal and I am happy.

  Just thought I'd share.

• cycle a precomp?

  Hello world

  It was so irritating day... I do not understand how to make an animation very simple cycle.

  Here's my process so far...

  I have a cartoon character that I've drawn on paper and scanned, then modified in photoshop. It's a simple 3 cycle design. It consists of a drawing with his right foot forwards, with both feet side by each and the other with the left foot forward. In other words, it's a very rough walk cycle. Simply, I want to created a composition of his 3 cycle design market and be able to loop that for once fo amount undisclosed, so that I can reuse its market in several small stages.

  Flash I simply take the three drawings that I would have done as vector are and turn them into a symbol that loop. Very simple and easy.

  After hours and hours of lookin at all these types of closure of tutorials I can't get my head around the expressions.

  IInterpreting images do not work for several reasons. An I want to be able to modify the drawings or update it if/when I update the original PSD files.

  Also, I don't want each drawing to represent simply a frame of the animation. I want to appear for 3 images, which makes a 3 each drawing drawing cycle 9 last frames. Other wise, the animation seems like it was on fast forward.

  My question is, how do I activate my precomp into a cycle really.

  Any helo is greatly appreciated... I only wish I knew a way to help someone else on this forum...

  see you soon

  -J

  Enable time remapping, and then use an expression of loopOut("cycle") on the demo set keyframes as needed

  Mylenium

• Late 2009 iMac Sierra gel & incomplete close

  Hi all

  I did a clean install of Sierra on my iMac late 2009, 3.60 GHz Intel Core 2 Duo, the 12 GB of RAM, a 1 TB drive, ATI graphics card. Everything seemed to happen. Now, I have two problems:

  1. at least twice daily than the iMac just hangs. The mouse moves, but can not select anything. Cmd - Tab will not pass applications. Keyboard does not respond. All I can say is that I always Mail, Safari, & Open Office 4.1.2 running. Have to hold the power button to turn off and restart.

  2. at the end of the day, when I stopped, the process is not finished and I just get a black screen (computer for desktop is black, but the items on the desktop are not visible), with the only docking station. Still, the only way out seems to be to hold down the power button to turn off.

  Anyone else having these issues? Is it that I can save for a clean install of Yosemite that worked perfectly before?

  Many thanks in advance,

  gimbers

  Hi aihometech,

  I understand that since the update of your iMac, you had some problems with the performance and the closure of your iMac. I know it's important to have a reliable work computer, so I'm happy to help you.

  We will have reset you the SMC on your iMac, which can often help with performance problems:

  Reset the management system (SCM) controller on your Mac - Apple Support

  If you still have questions thereafter, do this test in a new user account and view the results:

  How to test a question in another account on your Mac - Apple Support

  Thank you for using communities Support from Apple. See you soon!

• The battery: Cycle Count

  I recently bought a new macbook pro 13 inch (my first macbook never) and decided to read a little about the life of the battery.

  To my surprise, I realize that my cycle was 7!

  (Note: I only bought the macbook for about 4 days and charged for 3 - 4 times)

  And according to the sites, cycle counts only account all costs 100% (fresh short accumulation).

  In addition, my battery life estimated at 05:10 hours at 92%, but jumped to 08:40 hours to 84%.

  Should I be worried?

  I read that you can actually leave your macbook to charge overnight, but do you do with the power supply on or off?

  What is the best way to charge your macbook?

  If you are not satisfied with this experience, please return it and get another.

  You can return a Mac within 14 days of the purchase.

  For more information:

  http://support.Apple.com/en-us/HT204054

• Issue of registration of the cycle

  I was recording in cycle mode. And recording began around... This record is lost?

  No - open the project tree, and you will see each recorded in this region. Just drag one you want on a new track in the arrange window.

  

• I just took my ear dryer Flash pods. Also, they went through the complete wash cycle... and they are still working despite an elbow in the thread.

  I have no question... just an observation. I just took my ear dryer Flash pods. Also, they went through a full wash cycle. They still work despite a kinky twist in the wire. So with my test not planned, I find that they are watertight. Thank you Apple.

  I guess you will then test your new iPhone 7?

• What are the normal batteries fresh cycle when buying a used macbook pro

  Hello

  Looking to buy a macbook pro 2014, battery life is important enough and the machine, that I'm looking seems really well taken care of but the battery charge cycle is 300. Is this ok or normal? I don't like the idea that it is a third of the used way!

  Regardless of the number of cycles a battery has gone through, replace the battery with five years of service.  Age is a factor in the health of a lithium-ion battery.

  Assuming a battery will last in its setting of 1000 cycles design (most don't) suggests that 200 cycles per year would be realistic.  The MBP you are considering have 300 cycles seems to be quite normal given his age.  I wouldn't worry.

  Ciao.

• Auto-pause for cycling

  How can I set auto-pause for cycling.

  Hello

  Auto pause is currently only available for the training of inner and outer race.

  More information:

  Work with your Apple Watch - Apple Support

• My update is my phone keep cycling through the settings of update iCloud

  My update is my phone keep cycling through the settings of update iCloud

  What should I do

  Try disabling the Contacts under settings > iCloud. When you are asked if you want to keep them on your phone, select "keep". Tomorrow or Saturday, rallumer turn it back on again, select "Merge" and see if the problem is resolved.

  See you soon,.

  GB

• How can I find my battery cycles? I have a MacBook Pro under windows in Bootcamp.

  I have a MacBook Pro running Windows 7 in Bootcamp. My battery indicator says I should replace my battery. How I 1) know how many cycles my current battery on it and 2) know what battery I should seek to replace?

  I found the system hardware, but it only shows the Windows information, which included no battery cycles.

  Go back to the side Mac and look in the system (accessible via the about this Mac) report on the Apple menu

• I have a cycle recorded a vocal performance. I don't know how to get the anchor point to the film when the singer arrives early or sings after the cycle. Can anyone help?

  Loptic pro x. i. I cycle recorded a singer I just can't find a way to easily get small pieces of audio when the singer arrives early or sing a note sustained beyond the cycle. CAN ANYONE SHED SOME LIGHT ON THIS PLEASE?

  Just drag the right or left side of the region be expanded to include most of the voice.

  While cycling (replace) each record cycle is in fact only the region of an audio file that contains all the audio recording of the entire global cycle.    Then you cycle 2-3 bar record and do you 5 times counting from 1 to 20 in the microphone... Each region will be only 1 respective bar where the recording of the cycle started while you were, however each region refers to an audio file that contains all the numbers from 1 to 20.

  Then expanding to the right or left side of the region - will provide you with the early start or finish late audio.

  Same thing for taking records, except that you must be in edit mode to manipulate it start/end region.

• Loading tab is often incomplete

  Hello team!

  First of all, I must stress that I like in general Firefox as browser. However, there are a few problems quite annoying in my version of it, I hope it's the latter! (Version 41.0.2)

  All of the following terms refers to open a new tab. I have 5 x 3 grid of my new menu tab filled my sites commonly used, but often only the first two lines are displayed (1 photo attached, although edited for security reasons, I hope that you can always understand me).

  Another issue is that Web pages that I opened in new tabs (I love my tabs) are often left half loaded, raw HTML remains for me to see, while the current generation of the website remains incomplete until I refresh the page. I have no picture of it.

  Finally, and maybe it's the fault of my mouse, clicking environment to open a link in a new tab (I love my tabs!) will open on two or three instances of the same tab.

  The first two issues occur only on Firefox, I have not noticed them on other browsers, but the last is consistent throughout, so to make me believe that my hardware is to blame. In addition, I did not tried anything with my modules to date.

  Thank you very much for taking the time to read this request, and I would once again say how amazing of a browser is Firefox. I've been here since version 3.

  Thank you!
  ~ A.Q

  Hi, see if anything here helps: you can change the number of tiles on the page new tab in zoom in or back (Ctrl and + key, or Ctrl and - key).

  You can also keep the same zoom setting when a new tab is clicked: Type Subject: config in the address bar, press ENTER, accept the warning, scroll to browser.newtab.preload and double-click on it to change the 'value' of true to False.

  It is also possible about: config to change the maximum number of tiles, scrolling to the browser.newtabpage.columns (or Rows), then right-click > modify to set a new number of 'value '. - Editor of Configuration of Firefox.

  As an alternative, you might like to try the add-on new tab tools.

  If your question is resolved by this or another answer, please take a minute to let us know. Thank you.