Color Laserjet M551 turns landscape CW, want to CCW

Similar Questions

• Impossible to activate the services web ePrint for Color LaserJet M551

  Hello

  I read all the posts in this forum about the web services enabling ePrint to the question and tried all suggestions with no luck.

  Here's the situation:

  1. The printer works fine on place. I can print without problem.
  2. The printer is connected.
  3. All my router ports are open for outbound connections, including UDP.
  4. Communication using log in my router I can see that the printer can resolve DNS names using either my ISP DNS server or the suggested 8.8.8.8 and 8.8.4.4. Using nslookup shows ' registration-pro - site1print.houston.hp.com "Decides to 15.240.60.111 and" registration-pro - site2print.houston.hp.com "Decides to 15.201.224.79.
     This indicates that the printer can indeed resolve the addresses. Newspapers also Awakenings that the printer communicates with the servers (connection is established and data transferred) via https (probably the web service), but always after a few minutes the clearance process is to expire.
  5. I tried this allowing the procedure since a few days my believe that the recording servers should have worked some time during this period.
  6. I'm frustrated
  7. .. .even more frustrated
  8. what I am doing wrong?
  9. Help, please!

  trying to install eprint for my new M551dn Color LaserJet and it fails with the

  Who out there having the same problem I had. HP could not help me I restore to factory settings and reconfigured everything and all of a sudden the printer managed to enable web services and print the print code.

  Good luck to you face the same problem!

  / MrQQ

• Color Laserjet CP2025dn "turn the printer on" error

  Too often, I try to print documents (such as boarding cards and Word documents) and nothing prints. When I run the troubleshooter, it always says that the printer is turned off! The printer is still on. I have power down (both with the button, then with the power cord). I keep getting the error. I delete the docs pending and you try to reprint. Still getting the error. Updated firmware for the printer also.

  Have you tried to uninstall and reinstall the printer using the control panel > printers and devices?

  Jim

• HP Color Laserjet Cm 6040 MFP: Hp Color Laserjet Cm 6040 MFP, scan driver?

  Hi, I have a HP Color Laserjet CM6040 MFP, and I want to know if this printer is a driver of scan.

  You shouldn't have a driver.  The unit has the ability to scan to a network or a local folder.  Here's a link for how to use.  To install you may need to download the user manual.

  http://h10032.www1.HP.com/CTG/manual/c01300478.PDF

• Vista and Color Laserjet 5 M reprints all when the printer is turned on?

  Vist and Color Laserjet 5 M reprints all when the printer is turned on?

  It is a new one on me. I installed the printer with a barrette SIMM Postscript so it would work even at all under Vista and now it prints well but insists on the fact that I have all re - print he has never seen a reason any whenever I turn the printer to print something again.

  XP he has never done that, but I've always had the document cannot print the error that I ignored as he did print correctly.

  Google has not really revealed anything?

  ?? Type response level 1 I was looking for... These printers are a full restart, test of memory and when it is off.

  But I think I solved it, spent some time on google and there was a suggestion on the spooler in vista, was something like clear keep printed documents or print spooling first, I went also to start printing after the last page. Who took care of a lot of it somehow. Not sure why the generic installation program would need to be changed here. Possible I did for me somehow when I was trying to get the thing to work with the PCL driver too.

  Then I noticed that whenever I turned on the printer it is printing a page of demo postscript, for some reason any, it is enabled by default in the SIMM option. Turn power off and now its not wasting so much paper now.

  So two things to look for in the computer and the printer.

• LaserJet Pro M251nw color 200: Wifi turned off but still broadcasting

  Hello

  First, forgive my English.

  I have a HP LaserJet Pro 200 M251nw color, it has a capacity of wifi. Because the printer is connected with a cable ethernet to my router, I don't think that he had to use the wifi built into the printer.

  Thing is, when if I disable the wifi of the printer, and even if I disable "wifi direct to print", I can still see the SSID of the printer on my devices House (200 HP-Print-a6-LaserJet color).

  I looked on the forum and I tried the 'factory reset' turn, unplug the printer and taken, wait 15 seconds... etc. It did not work. I also installed the latest firmware.

  Any help would be greatly appreciated! :-)

  Hello revlib,

  Welcome to the Forums of HP Support!

  Turn off the wireless directly on Color LaserJet Pro 200 M251nw should have disabled the SSID broadcast. Since the display before disabling has not resolved, try the built-in webserver (EWS).

  To access the built-in Web server, you will need to enter the IP address for the M251nw in the address bar of your web browser. The IP address may be collected by touching the Setup program () > reports > Network Summary.

  Once in the SAP, click on network > wireless direct configuration > select and apply.

  

  Let me know if this has help

• using the color laserjet 3600n - I want to print in black and white, but it prints black and white negative. * beep *.

  using the color laserjet 3600n - I want to print in black and white, but it prints black and white negative.  * beep *.

  I was able to recreate what you see.   I managed to work around it by installing a different driver that is also supposed to be compatible with the CLJ3600.

  Please consider trying this as a possible solution:

  (1) uninstall the driver CLJ3600 by opening printers and fax machines, driver selection and right-click on it and select Delete.  Once it is removed, right-click on an empty space in the windows printers and faxes and select Server properties.  Click the driver tab, click the CLJ3600 and then click on remove.

  One when you're done, restart, and then install the CLJ3500 driver.  This is a previous version of the driver that has been implemented for the CLJ3600 and is compatible with the CLJ3600.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesId=315862&prodNameId=315867&swEnvOID=228&swLang=8&mode=2&TaskID=135&swItem=LJ-16838-3

  After installation, try printing again.

  The output I have indicates it will print is more negative.  Please let me know if you have success.

  One caveat about this solution.  The Color LaserJet 3500 doesn't support duplex.  Of workaround only works for two printing on the package of basic or the Color LaserJet 3600 N.

• Color LaserJet MFP M177fw Pro: installation of web services blocked to 'connection '.

  I'm trying to enable Web Services on this new LaserJet.  I am in the built-in Web Server page and the configuration of Web Services tab.  I clicked on 'Turn on' and it just keeps spinning in connection...

  DNS is 8888 and 8844

  All the other tabs work; It is connected to the computer and the Internet.  Help please?

  Thank you!

  Hi @crowndude,

  I see that you have problems with Web Services. I want to help you.

  I have provided a few steps to try to see if we can solve this problem.

  Turn off IPv6 on the printer.

  Go to configuration, network configuration, network, IPv6 Services and turn it off.

  This DNS works better for Laserjet printers. Please change the settings to see if this will help the printer built-in Web server.

  Preferred DNS address: 209.244.0.3
  Auxiliary DNS address: 209.244.0.4

  Power cycle the printer.

  If you still have questions, please continue with the following steps:

  Update the firmware of the printer by a USB connection. HP Color LaserJet Pro MFP Firmware update M177fw.

  Configure a static IP address for the printer. Proceed to Solution 3: printer of the assign a static IP address.

  Printer HP Color LaserJet Pro MFP M177fw and HP LaserJet Pro MFP M127fw and M128fw printers - printer does not keep the Wi - Fi connection.

  I'll send you another step to try in a private message.
  In the forum next to your handle name simply click on the envelope to see.

  If you appreciate my efforts, please click on the "Thumbs up" button below.

  If there is anything else I can help you, let me know. Thank you.

• HP Color LaserJet MFP M177 Pro: MFP177 frozen screen energy saver logo

  My new Color LaserJet Pro MFP M177fw still works, but the front is frozen with the logos of saver hp and energy, which means that there are no features in the control panel. I can therefore use it to manually, make copies, or do something that I would normally with the front panel. I tried everything the hp support asked me to do it (plug it directly into the wall, restart it, hold down the power button for a minute, plug, reconnect everything, etc.) and nothing has solved the problem. It is clearly a hardware problem?

  Hi @eng-ihab,.

  Welcome to the Forums of HP Support! I see that the printer is locked during initialization. I want to help you solve this problem. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  The update of the firmware usually fixes this problem, but I don't see one available for Windows 10. If the printer is installed on an older operating system also, I would say to run the update of the firmware with it.

  Here is the link: HP Color LaserJet Pro MFP M177fw, select the operating system.

  I would say to remove all toners, turn on the printer and wait for the printer to the State to reinstall toners manually. Just to rule out a toner not sitting correctly, the origin of this problem.

  You can move manually the carousel is not blocked.

  Open the scanner cover and cover less than one so you should see the toners.

  On the left side of the black frame, you will see an oval hole with a piece of white plastic on the inside.

  You will need to use something to press the white plastic piece, at the same time, push the carousel backwards, do not touch the toner however. It must be in good position to get out the toner.

  I've included a picture with the region, where to use the manual function of the printer.

  

  Make sure that the print queue is also allowed to leave, I saw this also cause the printer go in initialization.

  I can send a private message with some one more step to try.
  In the forum next to your handle name simply click on the envelope to see.

  If there is anything else I can help you, let me know. Thank you.

• HP Color LaserJet MFP M176 Pro: No printing on HP Color LaserJet MFP M176 Pro after update of Windows 10 anniversary update

  My HP Color LaserJet Pro MFP M176 does not print after update of Windows 10 anniversary update. I've updated two computers (HP Compaq Elite SFF 8300 and E6320 Dell), Hp with 2013 installed Office and Dell with Office 2010 installed. The printer is connected to my network. The latest "complete solution drivers' HP was installed before the upgrade. Printer does not printer-> Printtest properties, error notification appears and asks me if I want to troubleshoot the error. I can see the printjob in the spooler, but it is immediately deleted. Does not print any programs I've tried, with the exception of the notebook HP Print and Scan Doctor! When I troubleshoot with Windows printtroubleshooter, no problems found. Same thing with HP print and scan the doctor.

  I uninstalled all the drivers and the Hp programs, rebooted and installed "drivers complete solution." Same problem!

  On the Dell computer, I made a new clean install of Windows 10 Anniversery update, from a USB key. Office 2010 installed and 'full pilot solution again'. Same problem!

  On August 18, 2016, I found new drivers on Hp. new downloaded web pages "complete solution drivers still" uninstalled all the drivers and the Hp programs, rebooted and installed "drivers complete solution." Same problem!

  Among the many solutions, I tried turning the firewall. No help.

  I know that brother Corp has sent an email to their customers, there are big problems with their printers/drivers and the anniversary 10 Windows Update. Same problem with Hp printers/drivers?

  Someone who has a solution?

  Hello!

  Thanks for your suggestion of a solution!

  First of all, it fixed my problem of printing when I tried with a new user on both computers. Yet, I was a little confused that two updates and an installstion clean "updated anniversary" should lead to a curropted user profile!

  Then when I did what I always be with new computers/users, to the environment variables 'TMP' and 'TEMP' C:\Temp for the new user. Printing stops again. Extract a little more and found that users on C:\Temp needed to be 'total control '. 'Change' was not enough. Perhaps one of the new things in birthday update?

  In any case, there where the pleasure with your help!

• HP Color LaserJet MFP M277 Pro: LaserJet MFP M277dw announces its own wireless network

  I just installed a new HP Color LaserJet M277dw MFP Pro and noticed that it creates its own network wireless with the name ' HP-Setup > LaserJet 5 c-277. Even if the WiFi is turned off.

  I don't want the printer to make her presence known on WiFi and would like to know how I can turn this 'feature '.

  What is this function? I couldn't find any information about this in the manual, nor any of the settings of the printer where the name ' HP-Setup > LaserJet 5 c-277 "appears.

  @seron

  Ok...

  Try changing the Direct wireless / activate - or combination is necessary to turn the setting and the close up with the 'off' setting / disabled.

  In other words, no matter what the setting, Direct wireless can light up.

  Leave a few seconds between the time where as you toggle the setting.

  If that does not hit on it free, toggle the setting and then turn the printer off for about 20 seconds and then turn on the printer.

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  My answer-click accept as Solution to help others find answers.

• Color Laserjet M476dw MFP: page in the nonpaged area 'failure' BSOD when you install the latest driver for M476dw

  I just bought a Color Laserjet MFP M476dw for use on my wireless network.

  I downloaded the latest version of the suite of the HP driver: LJPro-MFP-M476-Full-Solution-13302

  for my Windows 8.1 operating system / 64 - bit and listed as version: 10.0.13302.320 - September 25, 2014

  I was connected with a local administrator for the installation level account

  I started installation, the printer was discovered and s/w install went fine until she gets to the point of print test page test page printed but that page was printing the computer locked with his (first) Disconnections:

  "failure of page in the nonpaged area".

  I turned off, restarted and after the connection got an error message that says:

  «The HP printer and Alerts State met and error and can not recover... Please restart...»

  Windows version: Win32NT 6.2.9200.0

  HP printer status and alerts version: 070.040.00169

  I rebooted again and got the same error...

  I started the uninstall program with the hope of just uninstall the printer status s/w and then put it back.

  but the uninstall program seems to have uninstalled the entire suite of s/w...

  Before going to this one more time, I thought that I would like to ask for suggestions...

  I've owned this phone for 6 months, and it was Cap... it's the first BSOD I did...

  Thanks for any help!

  I wanted to just close this thread:

  I was out of town for a week, but just returned and recalled to HP support.

  The technician did a large manual cleaning of the pilot has failed on my machine.

  and ran two different installers cleaning MSI Windows then with temporarily disabled antivirus s/w

  (which I had also done during initial Setup) we re-installed and everything seems to work.

• Color LaserJet MFP M277dw Pro: MFP M277dw unable to connect to wifi

  I just bought the Color LaserJet MFP M277dw Pro, and I can't connect to wifi. I have it connected via a USB cable and it works fine, it's just that I can't seem to connect to my wifi. The wifi seems fine, just connect my existing devices right (MacBook, iPhone, iPad). It finds the network, but it seems to expire when I put the password to connect.

  Hi @StephanieB2,

  Welcome to the Forums of HP Support! I understand that you are having problems with the networking of the printer. I want to help you solve this problem. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  It's really weird that the printer is expire when you put the network password.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  You can also configure the printer on the wireless network, thanks to the Wi - Fi Direct connection.

  Tap the icon on the screen of the printer wireless.

  Select the Wi - Fi Direct connection.

  Turn it on, if it isn't already, and if there is a code it marks down.

  Then on the Mac, go to the airport icon and connect to the network printer. (Direct 69 HP Laserjet M277)

  If requested a code or password, put the one you noted.

  Then open Safari and type 192.168.223.1.

  He will be responsible: the printer Web server integrated.

  Click the network tab.

  On the left side of the window, select Wireless Network Configuration and fill your information.

  Apply the settings.

  Can connect you to your network.

  Then add the printer.

  Click on the Apple menu, click System Preferences.
  Scanners & printers, then click the plus sign +.

  Select the printer in the list.

  Select your printer from the drop-down and click on the Add button.

  Test the printer.

  If there is anything else I can help you, let me know. Thank you.

• Color LaserJet MFP M477fdn Pro: M477 Software Installation fails at 99%

  Like others who have posted here, I have been unable to get the printer software to complete the installation. The printer is a Color LaserJet Pro MFP M477fdn, 3 months. I'm trying to install the software on a new workstation HP Z240 performing Windows 10 (64-bit). The connection is via USB cable. The printer and the software have been previously used with a Windows 7 machine without problem.

  I tried, repeatedly, to install the software from the disc supplied with the printer and also a 126.6 mb download HP Color LaserJet MFP printer M477 Pro series full software and drivers. The results are the same with a source - installation apparently progresses up to connect it the indicator product of progression from screen reached 99%, how it gives an error message "a Setup operation took too long to run. It is a fatal error, preventing the use of the product. Restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. "It takes about 20 minutes for the phase of installation to go from 0 to 99%, and then later hooked up to 99% for 2-5 minutes, the error message is displayed.

  I am able to print to this printer, but at least do not have the ability to scan from the computer there is no indication that the I.R.I.S. OCR software is installed.

  I had care of do not connect USB until you are educated.

  I tried repeating the installation without uninstalling first and get the same result.

  I used the uninstall contained the disk feature, and have deleted the printer to the computer using the Panel between the installation attempts.

  I tried to do a right click to run the installer as administrator and get the same result.

  I tried to install after clean boots with turned off Windows Firewall and all functions of the software Norton Internet Security including its function of firewall turned off.

  The event viewer displays none error entry at all and no entry identifies HP as the source of an event.

  I tried to connect via USB 2.0 and 3.0 ports.

  I cleaned recycle them and temporary folders.

  I have updated the firmware of the printer to the 20160331 version.

  Printed printer configuration report will not display any errors, nor that the printer itself indicates something is wrong and confirms the update of the firmware.

  I deselected the optional software, the devices experience HP and I.R.I.S. OCR, trying to install only the required files two more program scanning HP.

  Thanks for any help solving this.

  I think I understood the question, 10 windows installs its own driver, and the installation program expects the hp driver to install.

  DO this FOR THE HP INSTALLER PROCESS (when the percentage meter goes)

  1. go into the Device Manager and find the printer in the list of devices

  2. right click on the printer and select "Update Driver software"

  3. click on "Browse my computer for driver software".

  4. choose "Let Me pick one...» »

  5. Select the named driver: HP Color LaserJet MFP M477 PCL-6 Pro (make sure it's one with a dash between the pcl and 6!)

  6. click next and back to the installation of hp box and must now see the printer and continue the installation.

  -Alex

• LaserJet pro 177: bought used hp color laserjet pro mfp m177

  Installation disk arived broken. How can I do to replace it.

  Just upload what you want the site web theHP.

  http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443