Colorspace OfficePro 8100

Similar Questions

• HP officejet pro 8100 fails wake up when standby mode

  Hello

  I have a 8100 OfficePro wired to the domestic network of mp.  The printer is on 24/7. most of the time.  When it is idle, it remains on as it should be, but fails to print from a laptop wireless connected to the same system.  I have to turn off and on until I can print.  This happens with other wireless systems as well as I have on the same system...   As soon as I turned it off and on again everything connects and prints well.

  Richard

  In the printer, check that "Auto Off" is disabled.  Set a static IP address in the printer out of the router's DHCP range.  Use a channel 1, 6 or 11, never 'auto' fixed wireless, try all three.  Set the router to 20 Mhz only or 145Mbps router function.  Always use WPA2-AES encryption.  Power at the same time.  Power on router wait 3 minutes.  Marketing the printer and check that it reconnects to the router.  Try now.

• Tecra 8100: bios update of cd. exe does not command line

  I want to update the bios of my Tecra 8100.
  I downloaded the bios, but the pc has no floppy, I cooked up a cd bootable like this

  When I start the pc, F2, press c to boot from the CD-ROM, I get in a dos environment. I went to the drive Z, "dir" and see the bios.exe that I've burned to cd. To run it I type bios.exe and continue to be 'command unrecognized file name' when I type dir *.exe, he does not see the file either.

  Maybe I forget something here?

  + The message was edited by: removed link - bad info +.

  Hello

  Your described method does not apply to Toshiba laptops.
  Each computer laptop manufacturers supports various BIOS update procedures

  Toshiba on this page we:
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/downloadDetail.jsp?soID=356848&PF=true
  Here you can download the latest version of the BIOS for Tecra 8100

  The 4810.25 package must be unpacked everything first.
  Then you should check the files available.
  There is a readme.txt file that describes how to update BIOS using the ISO to CD.

  I hope I could help

• Tecra 8100 - exchange of motherboard

  Hi all.

  Sorry, my English is not very good, but I need help. My Tecra 8100 does not only turn on the leds of power, battery and drive hard, but does not (Nothing on the screen).
  I need to replace my motherboard and it is B36084962019-a (Tecra 8100 model PT810E-01152-IT) but I think only B36086672015-A motherboard.

  Can I use these model instead of my?
  Thanks in advance to all.

  Hi tibi_1,

  Your English is ok and train me it s understandable so don t you worry about this and welcome to the forum :)

  About your problem, I can t give an exact answer, but a Council: contact an authorized service provider. I think that in this case you need 100% sure answer and you can get it from professional people only because it s a user to user forum where you can talk with normal people like you and me.

  Then get in touch with the guys, they will help you and if you are not familiar with laptop disassembly, they can help you to swap the motherboard.

  Good luck! ;)

• TECRA 8100 stops spontaneously

  I have a 8100 Tecra with Windows XP SP2. The laptop stops spontaneously. Without warning, the screen goes black and flashes green battery LED. The battery is in poor condition (max. power for 5 minutes, then it beeps low battery). Therefore, I have the laptop still plugged into the mains.

  Does anyone have a suggestion how I can solve this problem?

  Greetings, Ben

  Hi Ben

  For the solution, you need to know why this happen. After reading the description of your problem, it is not easy to say why this is happening and we can only speculate what may be the problem.

  The question of a beginning: is this laptop cleaned in the past? I guess this may be full of dust and cooling system and cooling rack may be blocked by dust.
  Without appropriate computer hardware laptop cooling temperature critical and the result is suddenly turned off.

• Tecra 8100 seeing all installed memory

  I'm working on a Tecra 8100 laptop for a friend. Machine does not seem to recognize the memory installed in location B at all. Is there something in the BIOS to force her to perform a new analysis or I'm just looking at a broken slot? Everything seems OK visually and clips seem sound.

  I agree with Feliks;
  Module of RAM or housing could be faulty.
  You should try the RAM module in A slot in order to check the functionality.
  If the same RAM would work in the slot, but not in the B slot then I guess the slot B is damage.

• Tecra 8100 - no sound except in mic!

  I have a Tecra 8100 Windows XP.

  I can't get sound on the speakers or the headphones emitted by the computer, such as beeps, CD, etc. But if I have to reactivate the microphone, I can hear through the headset, ensure that the microphone picks up (there are a few comments without microphones, proving that the speakers work physically). All volume controls are the maximum and reactivated. All devices are enabled and correctly selected in sound control panels.

  Any help would be welcome! Is the sound card, or am I missing a driver? Could not find anything else on the web with similar symptoms. Thanks in advance.

  Here is the summary of the Everest report:

  Value of the field
  Computer
  Type of computer Advanced Configuration and Power Interface (ACPI) PC (Mobile)
  Microsoft Windows XP Professional operating system
  Operating system Service Pack [TRIAL VERSION]
  Internet Explorer 6.0.2600.0000 (IE 6.0 - Windows XP)
  DirectX 4.08.01.0810 (DirectX 8.1)
  Computer name TECRA-8100 (Tecra 8100)
  User name of the user General information
  Connection domain [TRIAL VERSION]
  Date / time 2009-07-15 / 14:18

  Motherboard
  Type of processor Mobile Intel Pentium III, 500 MHz (5 x 100)
  Name of TOSHIBA Portable PC motherboard
  Motherboard Chipset Intel 82440BX/ZX
  Memory system [TRIAL VERSION]
  Type of BIOS Toshiba (12/30/99)
  Communication communication Port (COM1) port
  Communication Port (LPT1) ECP Printer Port

  Display
  Video card S3 Graphics Inc., SavageMX (8 MB)
  Video card S3 Graphics Inc., SavageMX (8 MB)
  S3 Savage/MX (86 270) 3D accelerator
  Generic TV monitor
  Inner cover of Toshiba monitor 1024 x 768

  Multimedia
  Yamaha Native DS1 Audio CODEC audio adapter

  Storage
  Controller IDE Intel(r) 82371AB/EB PCI Bus Master IDE Controller
  Floppy Drive floppy disk drive
  Hard drive IBM-DARA-212000 (11 GB, 4200 RPM, Ultra-ATA/66)
  Optical drive TOSHIBA DVD - ROM SD-C2402 (8 x / 24 x DVD-ROM)
  Hard disks SMART Status OK

  Partitions
  C: (NTFS) [TRIAL VERSION]
  Total size [TRIAL VERSION]

  Entry
  Keyboard Standard 101/102-key or Microsoft Natural PS/2 keyboard
  Mouse HID-compliant mouse
  Mouse PS/2 Compatible Mouse

  Network
  IP main [TRIAL VERSION]
  00-10-A4-E1-F9-30 main MAC address
  Network card Xircom CardBus Ethernet II 10/100
  Modem TOSHIBA Internal V.90 Modem

  Devices
  Epson ActionLaser 1100 printer
  HP DeskJet 540 printer
  Infrared controller Infrared Port
  USB1 controller Intel 82371AB/EB PIIX4 - USB host controller
  USB device USB Human Interface Device
  Battery Microsoft AC adapt
  Battery Microsoft ACPI battery compatible control method
  Battery Microsoft ACPI battery compatible control method

  DMI
  Provider DMI BIOS TOSHIBA
  DMI BIOS Version Version 2.30
  TOSHIBA DMI system manufacturer
  DMI system product laptop
  DMI system Version Version 1.0
  DMI serial number of the system [TRIAL VERSION]
  DMI Motherboard manufacturer TOSHIBA
  DMI Motherboard product laptop
  DMI Motherboard Version Version A0
  DMI serial number motherboard [TRIAL VERSION]
  TOSHIBA DMI chassis manufacturer
  DMI chassis Version Version 1.0
  DMI serial number of chassis [TRIAL VERSION]
  DMI chassis [TRIAL VERSION] inventory number
  DMI chassis Type Notebook
  Total memory / free DMI casings 2 / 0

  Hello

  A good questions and I never heard of this topic which s...

  I think the fist, you should start to update the audio driver of your laptop. Therefore, you can see the Toshiba site for an update:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Before installing the latest version, you must remove the old version first and reboot the laptop.

  Maybe a reinstall of Windows with the Toshiba recovery disc could also be useful and in the worst case, it s only a hardware malfunction and it must swap the motherboard. :(

  Welcome them

• Tecra 8100, upgrading the BIOS, whitch that hard drive is taken in charge (40 GB)?

  Hallo,

  I have an old Tecra 8100 one I want to update BIOS. Who knows who is supported (20 GB, 40 GB) hard drive and where can I find the specifications?

  Thanks for your information.

  Georg

  Hello

  As I m wrong not the Tecra 8100 does support an IDE HDD controller.
  In this case, it should be possible to use the 2.5 IDE HDD.

  I can't say much about the formats supported, but the fact is that the size of HDD supported depends on the HARD disk controller. The old controllers IDE up to what the ATA - 5 (also called Ultra ATA/66 or Ultra DMA/66) supported LBA 28 bits, which allows you to use the 120 GB HARD drive max.

  Since ATA - 6 (also called Ultra DMA mode 5 or Ultra-ATA100), you can use IDE hard drives of more than 128GB.

  So if you want to, you can check your IDE HDD controller using a hardware diagnostic tool (IE Everest home edition). Then you might find out what IDE controller is and what drives are supported.

  See you soon

• Tecra 8100 - CPU max, DVD - ROM and BIOS update issues

  1. I have a 500 MHz processor on my 8100. I would like to upgrade to maximum capacity. I think it's 800 MHz since it is the highest, the series went to.
  But if it's 800 MHz, any Mobile PIII on this frequency do? Or should I check for special settings of the processor?

  2. I don't have a floppy, or ways to get drive one. And I'm not going to ebay one just for an update of the BIOS. Any ideas? A bootable CD with the files will do?

  3. What is the location of the DVD-ROM and what alternative models can I use? The 8200 went up to 8 x DVD - RW. Could I go further?

  Thank you. I hope that my post is OK like this instead of three different positions.

  1 take a look at the other Tecra 8100 models to determine which processors are compatible.

  2. I don't think that would work a bootable CD, you must follow a special procedure to update the BIOS and requires a floppy drive. If there is a version of Windows, you must use that instead.

  3 upgrade the DVD player can be difficult because you must use the correct master/slave settings, and it must have the same design of the façade of the original.

  Personally, I'm selling the laptop and buy a second hand faster one. It can work out to be cheaper.

• Tecra 8100 only start in safe mode

  I seem to have lost the display drivers for my Tecra 8100.

  As I tried to use an additional screen that worked well until I came to initialize the next day when it would only boot mode safe.
  What I did wrong and how I can fix?

  Detective driver does not work, everything happens as having performed an illegal operation.

  Hello!

  Have you checked the Web from Toshiba site?
  I doubt that this is because there you can download all the drivers.

  Check this box:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers
  The driver that you can find in * Archives *.

  Good bye

• Tecra 8100 - upgrade RAM and HARD drive

  Hello
  I just got a Toshiba Tecra 8100. I do not have this small a HHD and I wanted to know what size I can get it up to. I know y thread already asked this same question, but the technology continues to go better then perhaps there are HHD I can get.

  I am also wanting to upgrade the RAM. I've seen places that sell 144pin PC100 512 MB and I was wondering if it is possible to upgrade this 2 of them or not.

  Any input would be great!
  Thank you
  Doug

  Hello!

  The Tecra 8100 was delivered with HARD s up to 20 GB drive. I'm pretty sure that this laptop has a limitation of LBA 28 bits ([www.48bitlba.com]).
  I put t know what HARD drive you have at the moment, but a hard HARD 40 GB or 60 GB would work in this good old classic.

  In addition, the Tecra 8100 can be upgraded to 512 MB of RAM. So that you can t upgrade your laptop to more RAM.

  Good bye

• Install W2K on Tecra 8100

  Hi all

  I am trying to install W2K on a Tecra 8100, but I think I'm doing something wrong, because it keeps failing.

  If I just insert the CD it starts to start a load several files at a time when the Setup starts Windows 2000 (present at the bottom of the screen) and the installation crashes with a blue screen and the c0000221 error material unknown error \systemRoot\System32\ntdll.dll
  I read that, during installation, you will need to press F5 (in the screen where you can load a SCSI or raid driver) and then choose Advanced Configuration and Power Interface (ACPI) PC, but after doing this I get the same error.
  I have no additional material attached, it's original configuration.

  Any thoughts on how to solve this problem and get W2K on my laptop?

  Hello

  I think that this question has nothing to do with the Advanced Configuration and Power Interface (ACPI) or similar.

  I read about the error systemRoot\System32\ntdll.dll message, and there is no particular reason for this error.
  Sometimes some service packs missing cause this problem and sometimes hardware malfunction (RAM or HARD drive) could be responsible for a BSOD.

  You are able to install Win XP?

• Tecra 8100: Advice replace please - audio card?

  My 8100 Tecra faithful and beloved which is ideal for my purposes locked up the other day, in the middle of a session.

  Restart windows resulted in blocking machine once Windows is running.
  I started in safe mode - no problem.
  I have disabled all devices useless and then through a process of elimination of selectively allowing devices and reboot.
  I found that the problem was the Yamaha audio device - that turn on the machine and it would lock up, disable that and he would normally go.
  It worked fine now for a day with the disabled Yamaha audio device.
  I tried to uninstall/reinstall the device - no change.
  I even did a fresh install of XP - no change.

  I ran XP pro for over a year without problem (so far) and I consider not audio as criticism - just a nice to have.

  My questions are:

  Is there anything else I need to do in the way of diagnosis?

  Tips for common problems?

  Can anyone with experience of fixing these machines or similar notice if replacement of all of the audio card is likely to make a repair?

  I seem to remember the last time that I opened it about two years ago to change the processor that the audio Assembly was on a separate panel but is that all?

  Note that this is a _ancient_ machine and _not_ going to be taken to a repair shop where the Bill would be more that it is worth! I am competent to replace the sound card, more than that and I will probably continue to run without audio - I don't think that it worth replacing the motherboard just for audio...

  Thank you very much in advance for any constructive suggestion.

  Well, as you know these replacements are very delicate
  However, I don t think you will be able to replace this sound card but it s my personal opinion.

  From my experience, I know that the card (audio driver) his Yamaha is not fully compatible with Win XP SP1 and SP2. Update the audio driver is necessary.

  Google for it

  I searched a bit for some instructions how to remove these boards and found this page.

  There you should find a link to the page how to disassemble the Tecra 8100.
  http://repair4laptop.org/disassembly_toshiba.html

  Greetings

• Tecra 8100 hangs after startup

  Hello
  My Tecra 8100 has the same problem as described some time ago: the memory locations of MB were broken and doesn't have a connection properly. Even when I put paper or anything else between the cover and the memory module, it did not work and often my laptop has not yet started.

  I bought the new MB and now the laptop still start (I can see BIOS etc.) BUT crashes after Windows XP logo with notice: windows cannot start because the pci.sys file is damaged... The names of 'corrupt' are different, not only from pci.sys.

  When I portable computer boot from CD Win (to save the system) it blocks (crashes after 2-3 minutes). I tried to boot from Ultimate Boot Cd to detect the problem, but I can't do anything - always crashes after a short period of time - never start to run tests or Tools CD.

  I think that there is a problem of memory - I have 2 modules Kingston KTT-SO100/256, I tried to place them in different locations, together and alone, but nothing changes.
  These modules have worked with my old MB all the time.

  Any ideas?
  Radek

  I read on other forums that this error can appear if the modules of memory are corrupt or not compatible or the memory on the motherboard slot is faulty.

  Well, you have replaced the Board but do you use 100% identical to that of first?
  Perhaps modules of memory are not compatible with the new Board of Directors.

  "I found this Microsoft document that describes the Pci.sys is missing or corrupt" Error Message:
  http://support.Microsoft.com/default.aspx?scid=kb;en-us;319136&FR=1&PA=1&SD=HSCH

• Tecra 8100: vertical stripes on the screen

  I just bought a second hand Tecra 8100, who has been stripped of all its programs, OS. So I installed Windows98SE on this - now I get a screen with vertical stripes, which perch in the middle of the screen of the laptop with Windows just about visible in the background.

  I went to the display driver Toshiba and downloaded Web pages relevant windows 98se. Once on my laptop, the exe file does nothing; is neither their "graphics card" option in my device manager - everyone has ideas as to what is happening?

  Hello

  Please connect external monitor to your laptop and check if the result is the same. If so, there is probably a problem with the graphics card. If this isn't the case, I presume your laptop LCD screen is defective.