Compaq Presario SR5130NX: Cannot start Windows Vista after failure - HELP!

Similar Questions

• Cannot start Windows Vista after you download updates

  Original title: the last time I got a windows vista download it did.not end now if I turn off my computer it won, t wiyhout restart using a rescue disk also can, t open all files except when I connect

  Last time I had a windows down load it didn, t finished and my computer locked up had to use a rescue disk to start

  Hiartco1993,

  1. do you know what download you tried?

  2. do you receive error messages or error codes?

  3 have you tried booting in safe mode?

  You can first try to start in safe mode and try a system restore and check if it helps.

  Step 1:

  You can try to start in safe mode.

  Check out the link for more information on starting your computer in SafeMode below:

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2:

  You can try restoring the system to safe mode.

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  You can consult the links for:

  System restore

  http://Windows.Microsoft.com/en-us/Windows-Vista/What-is-System-Restore

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Cannot start windows vista: bugcheck 9f

  Title: bugcheck 9f, parameters = 0x3, 0xaf5fc030, 0xaf5fc030, 0x84e6c648

  my laptop crashed and closed, and I don't know what to do. can someone help me please.
  yesterday when I turned off my laptop it's ok.but today when I pressed the power button, it started normally
  He showed only two options:
  'launch start up repair (recommended)' or 'start windows normally '. Startup Repair cannot fix the problem and start windows normally does not work, it remains just on page load for hours.
  the problem is bugcheck 9f, parameters = 0x3, 0xaf5fc030, 0xaf5fc030, 0x84e6c648
  I really need my computer soon, and I do not have the windows cd .i don't really know what to do someone help me please

  Hi Ak_609,

  1. Did you the latest changes on the computer?
  2. When you receive the error message from error checking?

  First unplug all external devices (except keyboard and mouse) and then try to boot to the desktop and let us know the status.

  Method 1

  Check if the computer starts in safe mode and after back with the results.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Restart the computer to return to normal mode

  Method 2

  If the computer starts in safe mode then I would suggest you to perform control and clean boot if it helps.

  It is possible that some third-party programs installed on the computer is at the origin of the problem in normal mode.

  To help resolve the error and other messages, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• Cannot start windows Vista in safe mode.

  I followed these instructions to start Windows 7 in safe mode:

  I tried to start windows vista in safe mode by using the following:

  1. Click on the Windows icon in the left bottom of the screen while Windows is running in normal mode.
  2. Click on the arrow located to the right of the lock at the bottom of the popup menu symbol
  3. Choose "restart".
  4. I restart the computer, press the F8 key and hold.  I tried at the beginning of the sequence to reboot and after that the light appears on the mouse, but still before the windows logo appears.
  5. Restart the computer in normal mode.
  6. I tried the key down and also tried pressing the F8 key several times both giving the same results without success.
  7. To eliminate the possibility of a bad keyboard, I switched from keyboards with the same results.

  Can you tell me what I am doing wrong?

  You tap f8.

  You can have a F-Lock key in the upper right corner of your keyboard.

  http://www.bleepingcomputer.com/tutorials/tutorial61.html

  Read the other way at the link above.

  Table of contents > Vista.

  See you soon.

  Mick Murphy - Microsoft partner

• Cannot start Windows vista 64-bit is not after installing SP1

  When SP1 is installed, it will ask to "restart now" click on that and it not his "disconnect", then moves to step 1 of 3. " arrives at 97% and restarts. When it starts and happens to where windows should load up, it just goes to an error screen that says...

  "Unable to start Windows. A recent hardware or software change might be the problem. To solve the problem:

  1. Insert your windows installation disc and restart your computer.
  2. choose your language settings, and then click "next".
  3. click on "Repair your computer."

  If you do not have the disk, contact your system administrator or computer manufacturer for assistance.
  File: acpi.sys
  Status: 0xc0000098
  "Info: Windows failed to load because a required file is missing or corrupt.

  Now I can put in the disc of windows and repair and it will load and everything is good but not SP1 and if I try to install again, the same acpi.sys error again.

  I changed the power settings for monitar and readers do not turn off if the system is idle for long periods of time. I have reformat the HD does have 2 attacked together but spent the 1 hard drive and changed RAID.  This change has been to try to understand why my computer would hard lock. So far it isn't hard lock now. just can't update vista SP1 now. No update problem when he had 2 hard drives had attacked

  Any help would be great.  THX

  Hello

  Microsoft has released the analysis tool system update to resolve certain conditions that could cause the installation of updates and other software not only not for work. You don't have to manually run this tool. This tool is offered automatically through Windows Update on computers that have a condition that the tool could solve.

  System update readiness tool is available on the Windows Update Web site. To obtain this update, follow these steps:

  1. click on start-> click on Control Panel, and then click Security.

  2. under Windows Update, click check for updates.
  Important This update is available on Windows Update only to computers that have a condition that the tool could solve

  The following files are available for download from the Microsoft Download Center:

  Download the System Update Readiness Tool for Windows Vista (KB947821) package now.

  For more information, see article http://support.microsoft.com/kb/947821

  All the best!

  Diana D D

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot start Windows 7 after installing windows XP

  Original title: unable to load an earlier version of windows.

  I have been using windows 7 on my computer. Now, I installed windows XP but the problem is that windows 7 has been hiding and windows XP will load automatically. I mean that my PC does not give me the option to choose the two windows to use. I have not formatted the windows partition 7. There are, but hide. Please help me.

  Thank you.

  Hello

  Read the following article that may help you resolve this problem. This article is true for Windows 7 and Windows Vista.

  Windows Vista no longer starts after you install an earlier version of the Windows operating system in a dual-boot configuration

  http://support.Microsoft.com/kb/933179

  For more information: Dual Boot between Windows XP and Windows 7

• Cannot start Windows Vista

  Hello

  My laptop or laptop has a good light blue screen after a few setting for the display to external display was made by me.

  I tried to play a movie from my laptop to my samsung 40 tv monitor. It does not automatically detect monitor cable is plugged.

  Windows has stopped working probably because changed my setting to 16-bit to 32-bit screen...?

  What should I do in this case?

  Thank you

  Patrick

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  See you soon.

• Cannot start Windows Vista - ntoskrnl.exe is missing or damaged

  Hello, I am running Windows Vista. When I tried to start today I got an error message saying the ntoskrnl.exe is missing or damaged and should be replaced. How can I do that I can't use my netbook? Im not a geek, any advice would be apreciated, thanks

  Hello

  1. don't you make changes to the computer before the show?
  2. are you able to boot to the desktop?

  I suggest you try the steps from the following link:

  Windows cannot start with the error of the ntoskrnl.exe missing or damaged when the keys are pressed at the start
  http://support.Microsoft.com/kb/2022960

• G560 cannot start Windows 7 after onekey recovery

  I got the Lenovo G 560 0679 (2.54 Ghz, 4 GB Ram, DVD, Win 7 64 bit) * do not know the full product code * and created recovery disks. During the process, the system wanted 3 disks. After the second disc, the recovery disks have already been created. It was a little suspect. I tried the recovery disks. Then I have to restart the system. If I start it says that windows could not be started due to a change in hardware or software.

  I will go into an installation disc that has not been included in the box.

  Well below I got the offer to choose between

  Start windows normally

  use the last working configuration

  saving mode

  Save the network mode

  Save the mode prompt

  I also tried to install a Win 7 Home 64 bit edition on the main partition. Subsequently, I installed onekey recovery and tried to restore with the partition of lenovo. It did not work either.

  Can someone help me?

  Thanks for you advice.

  did you already changes on the software?
  Remove if inserted usb devices all.

  any other error instead of "change in hardware or software?
  I don't know if it will help but try to set the bios default settings (when you see the lenovo logo, press f2)

• Cannot start Windows Vista, even dvd installation

  I started my Dell Inspiron 1420 under Windows Vista Home Premium in place and led to a warning screen indicating an error in startup.  As stated, I started from my Vista installation DVD.  I ran the Startup Repair tool, and it failed.  The event log has been as follows:

  Problem event name: StartupRepairV2

  Problem event Signature 01: external Media

  02: 6.0.6001.18000.6.0.6001.18000

  03: 0

  04: 65537

  05: unknown

  06: no Cause root

  07: 0

  08: 2

  09: WrpRepair

  10: 87

  OS version: 6.0.6001.2.1.0.256.1

  Locale ID: 1033

  I then ran the System Restore tool and it failed.  I then ran the Memory Diagnostics tool, and it found no errors.  Given the lack of success, I decided to reformat and reinstall.  I used the Advanced Options in Windows Vista Setup DVD to remove the Partitions, format the drive and install Windows.

  Post installation Windows started successfully the first time but was running slowly.  I tried to download the drivers from the CD of Installation of Dell, but automatic execution failed, and when I tried to copy individual files, it also failed.  I decided to reboot the machine, but instead of Windows, I got a blank screen with white cursor blinking in the upper left corner.  I tried to reboot from the Installation DVD and once the progress opening white Windows files completed bar, I was presented with a black screen and a cursor again.

  Since then, I was not able to start any CD/DVD successfully.  What should I do now?  I am happy to reformat and try again, but I can not even on the screen to do.

  Help!  Please?

  Hello Nick_98,

  If we are hanging up when you use the installation disc, then the installation disc has problems or hardware on the computer problems that must be addressed before moving forward, there

  I advise to use diagnostics provided by your manufacturer to check for hardware problems.

  Please note that if the equipment passes the test, it simply means that no error has been detected it.  If we turn to the top of the sensitivity on the diagnosis, we can find errors.

  Best regards

  Matthew_Ha

• Error 0 x 00000024 cannot start Windows Vista

  Original title: 0 x 00000024 (0xFFFFFA80061c9530, 0xFFFFFFFF0000102, 0 x 0000000000190444, 0 x 0000000000000000)

  My girlfriends computer crashed last night and when trying to restart it gets just past the windows loading bar and then freezes with a black screen. I tried to restart running and loading safe mode, nothing works. I've used for a disc to boot from vista and which resulted in the freezing of the same in the same place as boot from the hard drive. I managed to get an error report which gave me the following codes:

  0 x 00000024 (0xFFFFFA80061c9530, 0xFFFFFFFF0000102, 0 x 0000000000190444, 0 x 0000000000000000)

  I am reletively in computer science, have always been able to save my computers except when something physical was wrong, but it's something that seems beyond me my DIY. I succumbed in discovering what exactly each of these codes, even though I know that they tell me what the problem is. Any help anyone could give would be appreciated that the whole College career is on the computer, including all the information it needs to complete its high seminar this semester and graduated.

  Hello

  A "Stop: 0 x 00000024" error message occurs when Windows Vista encounters an unrecoverable error when it tries to access an NTFS partition or a volume on the hard disk. As a general rule, you receive a "Stop: 0 x 00000024" error message during Windows Vista Setup when one or more of the following conditions are met:
  The structure of the filesystem or partition is damaged.
  There is a driver compatibility problem. For example, the driver of file system for a program antivirus or other utility can cause this problem.
  To troubleshoot a "Stop: 0 x 00000024" error message when you try to upgrade to Windows Vista, use one or more of the following methods, depending on your situation.

  Attention it is recommended that you perform a backup completes before you implement one of the following methods.

  Method 1:
  Run the CHKDSK program
  To run the CHKDSK (Chkdsk.exe) program, follow these steps:
  Use the Windows Vista DVD to start the computer from Windows Recovery (WinRE). For more information on how to start the Windows recovery, refer to the Microsoft Web site at the following address:
  http://windowshelp.Microsoft.com/Windows/en-us/help/f768809f-ED90-415f-a83f-89b42108b3551033.mspx
  In WinRE, open a command prompt. To do this, follow these steps:
  (a) on the screen to install Windows, select the language to install, time and currency format and keyboard or input method options and then click Next.
  (b) click on repair your computer.
  (c) click the Vista installation you want to repair, and then click Next.

  Note Click on load drivers only if you need to load a driver to access a hard drive.
  (d) click on command prompt.
  (e) at the command prompt, type the following command and press ENTER:
  CHKDSK drive: / r
  Note in this command, drive is the hard disk where you want to install Windows Vista.
  WARNING:
  Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost
  If Chkdsk.exe does not and does not repair errors on the hard disk where you want to install Windows, run Chkdsk.exe on other NTFS hard drives on the computer. To check the partitions that are configured on the computer, follow these steps:
  At the command prompt, type the following command and press ENTER:
  DiskPart
  At the DISKPART prompt, type the following command and press ENTER:
  Flight list
  Note the hard disk information that is returned.
  At the DISKPART prompt, type the following command and press ENTER:
  output
  At the command prompt, type the following command and press ENTER:
  output

  Method 2: Search for driver problems
  WARNING This workaround may make a computer or a network more vulnerable to attack by malicious users or by malicious software such as viruses. We do not recommend this solution to workaround but are providing this information so that you can implement this workaround at your own discretion solution. Use this workaround at your own risk.

  If you upgrade to Windows Vista, follow these steps:
  (a) install updated disk controller drivers.
  (b) uninstall any antivirus or the antispyware backup programs that monitor the file system for changes.
  (c) try to upgrade to Windows Vista again.

• Cannot start Windows Vista Home Premium. Missing or corrupted system registry file.

  And I don't have the windows installation disc to fix the problem.

  Hello

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  and if all else fails and you need to reinstall vista are the normal methods for computers preinstalled vista portable

  Contact the computer manufacturer and ask them to send vista recovery discs

  they do it for a nominal cost of $

  also ask them if you have a recovery partition on your hard drive to get back to the way you bought

  you would normally press F10 or F11 or Alt + F10, 0 at startup to start the recovery process according to the manufacturer

  Ask them of the exact key sequence

• Compaq presario v3015nr: cannot start, unknown bios password

  Hello

  Can someone help me with a laptop I dream of my grandfather who left us. I tried every password I can think that it can be used and so far nothing. I seems to be a bios password as it happens immediately with a message "Enter password" and even does not load Windows. After I try you times it comes up with a message "system disabled [13449] and I have no choice but to close it and try again." Can someone help me go beyond that or tell me how to reset the bios?

  Thank you in advance.

  Hello

  Try the steps listed in the link below

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/system-halt-error-message-or-BIOS-password-reset-generator/m-p/5010033#M292639

• Cannot start windows vista Basic... its keep restarting

  I started Windows... He goes to the page saying installation updates 3/3 0% complete do not turn off computer.

  then it shout down itself and start again from the same page... its keep repeating

  Tried, restoration of the previous point, tried to repair, attempted to open in safe mode, try the last known good configuratiuon etc... but no woreked... the same process keep repeting... can not turn off the system... unless I force him to stop... .Re to go back to the same page

  Help, please

  I did a disk cleanup and defregmentation yesterday and shout down the computer... but it never shout down since

  friend sorry, I tried all things but does not work.

  I started in safe mode, but afterbootingup it directly shows the window shutingdown and say ' updated lists: stage 3 3-0% complete don't have broad computer trun ' and then it shows "blocking down."

  and the computer restarts with the same process

  Help, please

  Do you have a recovery CD? If you try to back up your files first!

  then the system restore, if it does not, try to restore your system!

  Contact the manufacturer of your pc to ask them how can rocver your system, they allow u a, if they can, then you might have to pay! Normally, they provide a software on your pc to create recovery cd become! If you do not have or do not know, you will need to contact them.

• Cannot start Windows 7 after the update of the system

  I don't speak of Windows 7 RTM, I know is RC forum but I downloaded the RC of microsoft's official website and I can't install it, it reached the "end of installation"(ou quelque chose comme ça) phase and blue screen of death appears, saying "memory dump" and other things. ". That's why I downloaded RTM from a torrent site, I installed it, everything was fine, the aero was not on so I that I should update the video drivers and then I downloaded all the updates possible (via the control panel), then I restarted the pc and now I am not able to load windows , it's blue screen of death! Notice that I can run windows 7 mode safe mode, but when I try to start it in normal mode the blue screen appears. BTW, I have windows xp installed on my pc as well. So, here is my setup:

  AMD 7750 dual-core 2, 7GHz
  4 GB of RAM, 800 Mhz, but the system says 3.25 alone can be used
  ATI 4730 512 MB, btw I have integrated graphics card (ati hd3200, I think), don't know if it's important but...

  Here is the information about the error:

  Signature of the problem:
  Problem event name: BlueScreen
  The system version: 6.1.7600.2.0.0.256.1
  Locale ID: 1026

  More information about the problem:
  BCCode: 116
  BCP1: 871F13D8
  BCP2: 90C204B4
  BCP3: 00000000
  BCP4: 00000002
  OS version: 6_1_7600
  Service Pack: 0_0
  Product: 256_1

  Files helping to describe the problem:
  F:\Windows\Minidump\080809-15375-01.dmp
  F:\Users\blah\AppData\Local\Temp\WER-22953-0.SysData.XML

  Read our privacy statement online:
    http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:
  F:\Windows\system32\en-US\erofflps.txt

  Here's the crash dump:

  Debug version of Microsoft Windows (R) 6.11.0001.404 X 86
  Copyright (c) Microsoft Corporation. All rights reserved.

  Loading dump file [F:\Windows\Minidump\080809-14921-01.dmp]
  The mini kernel dump file: only registers and the trace of the stack are available

  Symbol search path is: * invalid *.
  ****************************************************************************
  * Loading of the symbol may be unreliable without a symbol search path.           *
  * Use .symfix to get the debugger to choose a symbol path.                   *
  * After adjusting your path to symbols, use .reload to refresh the locations of symbols. *
  ****************************************************************************
  Executable search path is:
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  Cannot load the image \SystemRoot\system32\ntkrnlpa.exe, 0n2 error Win32
  WARNING: Unable to verify timestamp for ntkrnlpa.exe
  ERROR: Module load completed but symbols can be loaded for ntkrnlpa.exe
  Windows 7 Kernel Version 7600 MP (2 processors) free x 86 compatible
  Product: WinNt, suite: TerminalServer SingleUserTS
  By: 7600.16385.x86fre.win7_rtm.090713 - 1255
  Computer name:
  Core = 0 x 82803000 PsLoadedModuleList = 0x8294b810
  The debugging session: 11:50:54.734 Saturday, August 8, 2009 (GMT + 3)
  System Uptime: 0 days 0:00:19.343
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  Cannot load the image \SystemRoot\system32\ntkrnlpa.exe, 0n2 error Win32
  WARNING: Unable to verify timestamp for ntkrnlpa.exe
  ERROR: Module load completed but symbols can be loaded for ntkrnlpa.exe
  Loading the kernel symbols
  ...............................................................
  ................................................................
  ..........
  Loading user symbols
  Loading unloaded module list
  .....

  Pirated Windows 7 allows malware, botnet zero-day ZDNet.com.url

  Messages rating helps other users

  Mark L. Ferguson MS - MVP