Computer hangs during the transfer of 16 jpeg files.

Similar Questions

• HP Pavilion p6-2069sc: computer hangs during the HP splash screen

  Hello.

  I plug an ASUS GeForce GTX STRIX 750Ti to use in my Pavilion P6 - 2069sc, but when I start the computer after installing my GPU, the screen hangs on the blue HP startup screen.

  When I try to hit the ESC key to enter the BIOS or any other keys it comes just a beep of the machine.

  It is a long beep every 20 seconds or so from the computer.

  When I use the integrated graphics card, everything works as they should.

  I already upgraded to 550W 300W POWER supply

  Because your computer has been manufacturer Sept 2011, there Legacy BIOS.  The latest vBIOS UEFI was initiated at the HP units at end of 2012.  That said, either you stay with a Legacy BIOS GPU card, or choose a dual hybrid card BIOS.  The GTX 660, or GTX 670, all of which are two high-end of the legacy card would be far superior to the GTX 750Ti.   All the current hype is looking for a lower quality card, the 750Ti, based on the more low power and some GTX offering a BIOS hybrid via Select manufacturer. The Asus could not be hybrids, as you can testify.

  http://www.hwcompare.com/17301/GeForce-GTX-660-vs-GeForce-GTX-750-TI/ 450W SS6

  http://www.hwcompare.com/17306/GeForce-GTX-750-TI-vs-GeForce-GTX-670/ 550W PSU

  http://www.GeForce.com/hardware/desktop-GPUs/GeForce-GTX-660/specifications

  Based on your existing new POWER Pack, (hopefully a quality unit), 660 GTX would be good.  In my humble OPINION, an EVGA GTX 660 is better based on your power supply of the system. Please call EVGA for re - check a Legacy BIOS.

  PS I have a EVGA GTX 660 and 670 in my BIOS Legacy of <>towers.  I tried an ASUS, but he did not have an ASUS motherboard. Strange, but ASUS check the fault has his own card. Cost me $50 return shipping cost, so Please check with any manufcacturer.

• HP Pavilion 23: computer hangs during the boot process

  Computer updates been made 2 days ago and has frozen black screen. Now does not start at the top. Starts the process and then freezes. He did start once yesterday and was going well for a few hours, then got a message saying computer had a problem.

  Error message:

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED (atikmdag.sys)

  Now back to not start upward again, hangs with the HP logo on the screen.

  Hi there @ldgie25.

  That the Forums are with you!  I understand that, after a few updates, your computer does not start correctly and freezes on the HP logo.   I'm happy to help you with this.

  Since it was started once, but then had a blue error screen, I suggest using the computers HP - use Microsoft System Restore (Windows, 10, 8).   Follow the instructions in the section «restore your computer when Windows is unable to boot normally»  See if it will start normally after the restoration. If yes then you probably want to prevent the offending update to install again.

  Please see the following for how to do this:

  How to temporarily prevent an update for driver reinstallation of Windows 10 - support.microsoft.com

  How to uninstall and updates to block and drivers on Windows 10 - howtogeek.com

  Please let me know if it works for you and if it does not solve your problem, please mark this message as a solution. Bravo would be appreciated as well.

• The computer hangs during the analysis of Microsoft Security Essentials. Error checking: 0x0000007f

  Hello.

  My computer - windows 7 x 64 SP1 - is now fallen down several times all by performing a full scan of the system with Microsoft Security Essentials. This is the last event:

  Log name: System

  Source: Microsoft-Windows-WER-SystemErrorReporting
  Date: 28/02/2016 13:20:17
  Event ID: 1001
  Task category: no
  Level: error
  Keywords: Classic
  User: n/a
  Computer: GAMUT
  Description:
  The computer was restarted after a bugcheck.  The bugcheck was: 0x0000007a (0xffffffffc0000185, 0x000000010495a880, 0xfffff6fc500110e8, 0xfffff8a00221da3c). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 022816-17986-01.
  The event XML:
  
   
     
      1001
      0
      2
      0
      0
      0 x 80000000000000
     
      636121
     
     
      System
      RANGE
     
   
   
      0x0000007A (0xffffffffc0000185, 0x000000010495a880, 0xfffff6fc500110e8, 0xfffff8a00221da3c)
      C:\Windows\MEMORY. DMP
      022816-17986-01
   
  

  You can access the minidump here: https://www.dropbox.com/s/shogzx1tvdqh904/022816-17986-01.dmp?dl=0

  Can you help me? I don't know how to parse this file to understand what the problem is.

  Thank you!

  92 KB in bad sectors.

  You should check this number against the future reports. It will not reduce, but if it increases, you need to back up on external media and replace the disk.

  Cleaning of unused 161 entries index $SII of file 0x9.

  Cleaning of unused 161 entries index $SDH of file 0x9.

  Cleaning of 161 unused security descriptors.

  It is a problem less than bad sectors. If you get these errors, you must test the drive using the drive manufacturers test utility.

  Model Hitachi HTS543232A7A384 ATA Device

  IBM - Hitachi Drive Fitness Test 4.16

  http://www.MajorGeeks.com/files/details/ibm_hitachi_drive_fitness_test.html

• Windows 7 hangs during the transfer of data from one drive to another

  This problem was pestering me for a long time, well over a year.

  When I transfer data from one disk to the other (generally large amounts), the computer crashes and I get a blue screen or it just restarts.

  Initially, I thought it was a faulty hard drive, so I replaced that, but the problem persisted. I ran diagnostics of smart drive on all my drives and no problems have been picked up.

  Then I replaced my RAM assuming there that all. The problem continues.

  Then I replaced the video card. The same problem.

  I then upgraded to windows 10 and the problem became more acute, so I rolled back to windows 7.

  The SSD has the latest firmware, the latest graphics card drivers.

  I think now it is one of the following two issues:

  Either my SSD drive that contains the operating system or motherboard?

  Someone at - it ideas of how to diagnose precisely this problem or how to solve it? Would contribute to a new facility?

  PC: Windows 7 SP1, AMD Phenom II X 4 965, Kingston 16 GB 1866 MHz DDR3 Non - ECC CL9 DIMM (Kit of 4) XMP beast series - HX318C9T3K4/16, AMD Radeon (TM) R9 series 200, Asus M4A87TD/USB3 motherboard

  Pilot, verified and associated usbfilter.sys from Advanced Micro Devices Inc. USB filter driver.

  Remove the driver current completely and install the latest driver available.  For instructions on how to do read everything to update the drivers of my partner JMH3143 http://answers.microsoft.com/en-us/windows/wiki/windows_other-hardware/updating-a-driver/a5e6345e-af9b-4099-bef0-8d22254aa1c1?tm=1436753520149 here

  Also and important you need to update this driver since 2005.  It is a known problem in win 7 (ASACPI.sys)

  Pre 2009 this driver version is a known cause of BSOD.
  
  Please visit Asus tek computer Inc. - support - drivers and download p7p55d the
  http://support.ASUS.com/download.aspx?SLanguage=en&m=P7P55D%20Le&p=1&s=32&OS=29&hashedid=e7zic83pvqsr80lm

  Scroll to the utility category, then scroll down to the "atk0110 driver for Windows XP/vista/windows 7 32 & 64-bit" (it is about 12 down).
  Download and install it.

  Go to c:\windows\system32\drivers to check and make sure that the file asacpi.sys is stamped 2009 or 2010 (not before).  If you are using Win 8 there are at least a 2012 version that is needed for this.  If you can't find it on the site of ASUS you can download using windows update.  Read about it here

• The computer hangs during the communication via a serial port

  I developed a code in LabVIEW 2011 to connect with the XY stage. It's actually two steps mounted perpendicularly. The installer of the system is that a (made by the same manufacturer as the stadium) gamepad is connected to the USB port on the computer if a USB to Serial converter. A step is daisy chanied to the controller and the other stage Garland at the first stage.

  To our application had to continually check the status and position of the steps X and Y. Because the joystick also returns responses when a request is sent to all devices, I need to send applications individually; for example. one request per order per device, making it a total of 4 orders. It takes care of the error returned by the controller. The problem, however, is that after a while the freezing of the program or the computer stops and restarts. It is located about 13 minutes (on average) after the start of the program. It also happens even when no command is sent to the devices. I put 50 ms delay before each send two commands (position and status) by device. Basically, the application waits for 50ms before sending two commands for X stage and the receipt of the response and when everything is done with X stage, he expects another 50 ms to do the same for step Y. Should this procedure goes on until the application is stopped. But as I said, there is a problem. Now, I guess the problem is that serial port buffer overflows. He chose to increase the delay time, but if it works to solve the problem, then I have no choice!

  I would appreciate any thoughts and comments!

  After a lot of time to experiment, I am convinced that the issue was with adapter Profilic.

• Computer hangs during the installation of updates (I have to install 64)

  What should I do when I cannot yet download or update anything without my computer freeze or lock up on me.

  Hi floridahmbdy,

  Check if an error message or error code listed in the event viewer, you can check the link below:http://windows.microsoft.com/en-us/windows7/What-information-appears-in-event-logs-Event-Viewer

  Try the methods below:

  1. start the computer to boot and check if you are able to install the update to Windows. Link below will help you to start the computer in clean boot:http://support.microsoft.com/kb/929135

  Make sure that you reset the computer in normal mode in step 7.

  2. you can also try the steps from the link below: the problems with the installation of the updates:http://windows.microsoft.com/en-us/windows7/Troubleshoot-problems-with-installing-updates

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer hangs during the update of Windows 8

  My laptop recently posted a message saying that he would automatically restart in 15 minutes to install a Windows Update.  After 15 minutes, it restarts and a screen will appear that says "Configuring Windows updates.  Do not turn off your computer. "He started to install, then stalled to the point 13%.  I rebooted several times, and it keeps the timing at this point.  I can't go past this screen for something else, so I have no use of the computer right now.  Y at - it a fix for this problem?  Thank you.

  Hi Rebannle,

  What is the brand and model of your computer?

  This problem may be caused for the following reasons:

  Conflicts of hardware/software.

  System files are corrupt.

  You can see the steps from the following thread that was answered by MikeSimmonsUK on November 7, 2012, that will help us solve the problem.

  Windows 8 updates stuck at 13%. (NOTE: laptop HP - audio drivers)

  If the problem persists, you can also see the steps in the following Microsoft article: Windows Update crashes when installing updates in Windows 8, Windows 7, or Windows Vista

  Notes:

  When you perform the System Restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  When running at Refresh: the applications that came with your PC or you installed on Windows Store will be reinstalled, but all the apps you have installed other Web sites and DVD is deleted. Windows puts a list of applications on your desktop after you refresh your PC.

  Keep us informed on the status of the issue.

• [SOLVED] Windows 7 hangs during the "you want to allow this program to make changes to your computer.

  I was recently on my computer and running windows 7 with happiness and problem free, until I downloaded a file from the internet. When I opened it, windows asked me if I want to allow this program allow changes. However, there is the rub. When I click on 'Yes', the message will disappear, but the computer hangs at the screen has gone even a light, tinted gray, with all of the programs that are still running in the background. It freezes for about 2 minutes and then decides to return to normal, free for me to return to work and navigation. However, the program that I have originally intended to be performed by him to make changes didn't work at all. Confused, I ran over and over again, but with very little success, and the problem continued to appear. I tried to launch a clean boot, but that doesn't help more. Can someone help me please? Thanks :)

  Thank you for the support, but I solved the problem.

  I did a system restore, and it seems that a microsoft critical update was the culprit of all this? In any case, everything seems to work now and thanks again for all the support and help, I appreciate it a lot :)

• NB100 restarts during the transfer of files and others

  Hi, there are some problems, I've had this days with my NB100:

  (1) blocking during the transfer of file with scp-online HW reboot. Seems to be a bug in driver wifi...
  (2) no way to restore my system after hibernation-online HW restart
  (3) Toshiba function auto zoom turned on sometimes when I come back just when the screen saver starts.

  In any case, it's a good NetBook, and it's really nice to see that ubuntu pre-installed on a Toshiba computer.

  Hello

  I noticed that Toshiba has offered some BIOS updates for similar problems.
  Have you checked Toshiba support page on the BIOS update?

• Satellite Pro A110 crashes during the transfer of the large data in LAN

  Hello

  My Satellite Pro A110 crashes during the transfer of the large data in LAN. The network driver is a Realtek RTL8139/810 x Family Fast Ethernet NIC I've been looking through this forum and found some wire whit exactly the same problem, saying that the solution is to update Realtek lan set up in BIOS, not the computer BIOS, but I can't find any link to download the necessary upgrade file. Can anyone tell me please where to find this upgrade file or send it to me directly?

  Thanks in advance

  Is - this transfer of data in the company where you work? Do you want to download data from the server, or how to understand this? How to understand what you mean under big data?

  Have you tried downloading data on the Internet? For example, if you try to download some trailer HD (more than 200 MB)?

• I am trying to install windows xp from the disk, but it hangs during the installation process. no error code. It just hangs. What is the cause and what is the solution?

  I am trying to install windows xp from the disk, but it hangs during the installation process. no error code. It just hangs. What is the cause and what is the solution?

  Hello

  1. at what stage of the installation, the computer crashes?

  2. what operating system was installed on your computer prior to this?

  If you have the similar problem as mentioned in these links, you can follow these links and check if the problem persists:

  Windows XP Setup stops responding (hangs) during the "Preparing Installation" phase

  Windows XP does not meet the Message "Setup starts Windows XP"

  Hope the helps of information.

• With the help of the network location and mapped a drive to the server FTP. during the transfer of very large amounts of the login information is always lost.

  With the help of the network location and mapped a drive to the server FTP off site; during the transfer of very large amounts of the login information is always lost.  Computer power settings are configured to not to do no matter what, I'm assuming that the ftp server can publish a scenerio timeout but is there a way for my computer and windows to restart the file transfer?

  Hello

  Thanks for posting your question in the Microsoft Community forums.

  I see from the description of the problem, you have a problem with networking on the FTP server.

  The question you posted would be better suited in the Technet Forums. I would post the query in the link below.

  http://social.technet.Microsoft.com/forums/en/w7itpronetworking/threads

  Hope this information helps you. If you need additional help or information on Windows, I'll be happy to help you. We, at tender Microsoft to excellence.

• got the new ipad. during the transfer of applications, some are dark. Why?

  got the new ipad. during the transfer of applications, some are dark. Why?

  All applications are probably install and not finished yet. Make sure you are connected to a wireless network and let it enabled applications can continue to have downloaded and installed.

• Warning message to turn off "Are you sure that you want to copy this file/folder without its properties" message during the transfer of files and folders on network file servers? »

  Original title: Annoying message of loss of property

  Win7pro x 64 here.

  Is there a way to disable this annoying message "Are you sure you want to copy this file/folder without its properties" during the transfer of files and folders in all of network file servers?

  Pokermon salvation,

  It would be better if post you this question in the forum category below where this problem is related to Windows server 2003.

  Windows Server forums

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  If all goes well, they will be able to solve this problem.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.