Computer Vista will not print to Deskjet 930c on home network

Similar Questions

• Lexmark Interpret S405 is not communicating with the computer and will not print

  My computer works with Windows 7 and updates automatically.  I got the Lexmark Interpret S405 for 18 months, and it has worked great until a couple of months.  When I try to print, I get an error message indicating that the printer is not communicating with the computer.  When I check the printer, it shows he's ready.  The print job shows that it is ready to print, but nothing happens except for this message.  When I try to erase the impression, it really takes a lot of time - usually have to unplug the printer so that it can finally clear.  Then it still will not print if I try again unless I restart the computer.  Lexmark support page says that there is a problem with Windows 7 and their product.  All the solutions for this problem yet?

  Computer model of the bridge ZX6970, OS 64-bit, intel CORE CPU I-13 3.30 GHz, Windows 7 Home Premium.  Can someone advise a fix for this problem?  Thank you!

  Hello

  Have you tried to download and install the updated firmware for the Lexmark Interpret S405 from the manufacturer's website.

  If this isn't the case, please download and install it.

  Download Firmware for your printer!

  We know the results.

• iMac will not print to Deskjet 3050 a

  Hello

  I'm running an iMac in early 2008 with the operating system upgraded to OS X 10.7.2.  including all updates.  Just bought a Deskjet 3050 a and downloaded the software HP istall to the address on the HP site.

  Spent by the installation procedure except when it came to the question "install that Print" it didn't come with the identifier of the printer only.  so I couldn't continue.  Printing of diagnostic said no problems found congratulations on successful installation, etc.  However, even if the printer is connected it will not print.  What can I do?

  AHA!  I also noticed you are using a D-Link Extender, which indicates that you don't have a router.  According to your description of your Internet configuration, the device emitting IP (DHCP server) addresses is likely on a device outside your home.

  If this is the case, this device is likey to not allow devices to "talk" to each other on his network.

  If replace you your range extender with a router and all devices connected to the system should work perfectly.  Thoughts?

• DeskJet 940c: new 78xl cartridge will not print on Deskjet 940c

  bought 78xl tricolor cartridge.  Have only used the 78 before regular.  New cartridge will not print.  Replaced by the old cartridge - printed perfectly.  When I opened the printer, the cartridges for the little happy face moving, I have not a clue as to what is happening.  I would simply return this cartridge?  The 78xl is compatible with the 940 c?  15 black continues to print well.

  ARGHHHH.  Help, please...

  Hey @JaniBee ,

  Yes I recommend you return the faulty new cartridge and replace it! If you buy the new cartridge and it fails well then let me know and we can look at the printer and excludes a faulty cartridge error.

  Get back to me and let me know! Have a great day and a wonderful holiday season!

• Vista will not print works wireless but wired through router

  I have 2 wireless modem ATT DSL wire connected to a firewall server / print wireless Netgear FM114P ProSafe and a router 3Com to increase the number of connections.

  I have a Vista laptop that allows to print everything wired through my 3Com router connected to th Netgear FM114P ProSafe, server print/firewall wireless connected to a HP laserjet 6 p printer, but while Vista connects to wireless internet, it won't print wireless HP connected to the print server.

  I have configured the other portable XP to print wireless using the same ip address but can't get Vista to work.

  Hello

  Your 2 wire wireless mode, is actually a Modem/Router combo.

  I hope that your Prosafe device is connected as a switch with an Access Point.

  If it is connected as a second router you have independent networks that will not work against the second router NAT doble and thustwo.

  Re-set according to the principle here, http://www.ezlan.net/router_AP.html

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Index cards will not print to Deskjet F4480

  I'm running OS X 10.6.7. I use a HP Deskjet F4480 all-in-one printer.

  I am trying to print on 3 x 5 or 4 x 6 cards, and even if the printer recognizes these sizes, it does not print on the cards correctly. Instead, he spits them simply white.

  I had to go to work today before I could try the same size of page in another program. Everything that I tried this on is Word 2011. Using a simple program like TextEdit can produce better results? What should I try?

  lamcqueen-

  What are the settings in the Page layout Word box?  The settings are applied to the "Format for: any printer" or your Deskjet F4480?

  Does anyone else have any other thoughts? -Randy

  -----------------------------------------------------------------------------------------------------------------
  If this was helpful, please consider clicking on the White Star of Kudos to the left.

  If this provided the answer to your problem, and you were the one who started this topic,
  Remember to mark this message "Accepted solution" to help others in the future. Thank you!
  -----------------------------------------------------------------------------------------------------------------

• Printer HP Officejet 4620 on Windows Vista will not print

  Hello. It is a replacement printer sent me after the motherboard on my first brought to stop working 2 months. The replacement printer is installed, but it stopped printing. He did print test pages when I first put in place, but when I go to print a standard Microsoft Word 2007 document, I get the flashing box that says: "the printer is ready. Click OK to continue. The flashes of the box, but when I hit okay, nothing happens and the print queue of the printer says "delete." I ran the HP scan and fix, and he reported that everything was going well. The machine still does not print!

  If you can't get the program to uninstall, then it may be a problem with the way that the Windows operating system treats the registry keys.  Is there a Fixit program provided by Microsoft that allows programs that cannot be installed or uninstalled.  Please click the link below and use this utility to help the uninstall process.

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall/

  Let me know if this can help,

  Jason

• Computer Vista will not start, the computer keeps restarting. Also had a BSOD "STOP: 0 x 00000024 (0X8D5389C, 0X8DB535CC, 0X001904AA, 0X8CC143A1)" while trying to use reinstall OS Dell drive

  Original title: corrupted vista OS?

  My Dell studio slim desktop (Vista OS) that I have since Mar09 died on me 2 weeks back and I can't it start and it will keep rebooting until it resembles the wide long beep (as if a deceased person)

  Whenever my com has restarted, it shows the following:

  Safe mode

  Safe mode with networking

  Safe mode with command prompt

  Last known good configuration (Advanced)

  Start Windows normally

  All options will be led to the recovery of my com & return the same screen.

  It will always get stuck at the loading bar where the com starts boot & restarts itself.

  I tried to attach the hard drive to a different com as external hard drive, but it will begin to restart that com & hang the CMO as well

  I tried using the disc to reinstall OS from DELL and it will show a msg of error (blue screen) with the following text:

  Disable or uninstall the antivirus, Defrag disk or backup utilities. Check the configuration of the hard disk & check for any updated drivers.

  Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  STOP: 0 X 00000024 (0X8D5389C, 0X8DB535CC, 0X001904AA, 0X8CC143A1)

  NTFS.sys address 8CC143A1 base at 8CC06000, Datestamp 47918a 96

  Any idea of this situation?

  Is it possible to save my cause com have not all backups from my hard drive?

  Any help would be grateful.

  Thank you

  Hi Bill,

  I forgot to include some info as well... I replaced the 'touched' hardisk (Barracuda 500 GB) to an unused a (Barracuda 160 GB) and the problems disappeared. Whenever I change back the 500 GB in the com, the sound signal occurs only backwards the system continues the reopening for abt... 10 + times?

  "My Office studio slim (Vista OS) Dell I have since Mar09 died on me 2 weeks back and I can't it start, and he'll keep rebooting until it seems a beep long-lasting looks not (as if someone died).

  So the questions are now fixed, unless you put the other disk hard?

  Test the other hard drive.

  Go to the website of your computer manufacturer > find specifications of hardware in your computer (hard drive) > access the Web Hard Drive from the manufacturer site > download their diagnostic software > make a Bootable disc > test your hard drive.

  And run the F12 as I advised you to do so.

  It is DELL's Diagnostics software.

  Good luck with it.

• Computer Vista will not be stopped

  I tried to shut down my computer for days now.  Vista - and still running, he simply refuses to stop.  Suggestions anyone?  I have all the SP2 updates and I tried just August everything I read about to solve this problem... except the only thing that works!  Thank you

  Hello

  This problem can occur when the power management profile turns off your network adapter.

  Method 1: disable the functionality of management of power in network adapters

  a. click on start

  b. right click on computer

  c. click on manage the

  d. click on Device Manager in the left pane of the window

  e. expand your network card.

  f. now you will see your network adapter or adapters if you have more than one. Right-click on the network component, and then click Properties.

  g. go to the power management tab.

  h. ensure that all of the checkboxes are checked (check boxallow the computer to turn off this device to save power is off).

  i. When you have disabled the boxes, click ok and restart your system. Put the computer in mode 'sleep' and check if you still have any questions.

  Method 2:

  If the problem persists, you can try to perform the clean boot and check if it helps:

  How to troubleshoot a problem by performing a clean boot in Windows Vista and Windows 7.

  http://support.Microsoft.com/kb/929135

  Note: Don't forget to reset the computer to start as usual, once the problem is resolved. Follow step 7 of the KB article.

• Laptop running Win Vista will not print wireless connection

  I have a problem I'm trying to print on a printer of all-in-one HP Photosmart 2575 of my laptop.  The laptop is running Windows Vista and connect to the network using a Linksys WRT54G2 router is using.  The printer is connected by Ethernet cable to my desktop (Windows XP), and it prints fine.  No matter what I do to print via the wireless router, nothing happens except that the print output only goes to print that and sits down.

  I down loaded the software HP2575 of Vista and updates directly from the HP site.

  Six days ago, when I first installed everything on the new laptop, I did a test print very well.

  Computer portable printer is configured to print documents Spool and using the Port "Dot4_001 HP Device.  In addition, it has the value "share this printer."

  I tried a test and connected the laptop to the printer using a USB connection, and that runs just OK.  Wireless internet works fine for web connections.

  So, what have I done wrong

  I finally solved the problem. I don't know why it works this time.

• Computer * Vista * will not recognize Sansa Clip

  I checked the USB port and it is fine, but when I plug it in it does not appear on my computer.  "I tried on my computer laptop son * Windows XP ' and it shows up there.  Can someone help with the Sansa Clip and Vista?  Thanks in advance!

  Have you tried switching USB mode of the Meteorological Service of Canada, or forcing MSC mode Clip (hold the Center button down when you connect USB cable between computer and Clip)?

• Computer Vista will not "Shut Down"

  Why is Vista not 'Shut Down' when we try to? The computer gets to that stage and works on and until what we manually turn off the computer.  When we click on Shut Down, the OS disconnects then goes down at the stop, but isn't.  Anyone facing this problem.  It is found on all 3 computers OS Vista

  Also, when updates Windows tries to install computers work for too long at a time in the mode of installation on the same day.
  Don't know if they are related.
  Thanks for the tips.

  Hi jem820,

  ·         When was the last time it was working fine?

  ·         Have you made changes on the computer before this problem?

  ·         You receive an error message all in stop or restart the computer?

  Follow these methods.

  Method 1: It could be due to a program or device driver interfering with Windows power settings. See the article and try the steps in the article.

  Why my computer won't turn on or off quickly?

  http://Windows.Microsoft.com/en-us/Windows-Vista/why-wont-my-computer-turn-on-or-off-quickly

  Method 2: Install the updated drivers for the graphics card on the computer visiting the site of computer manufacturer.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 3: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  Note: After the boot minimum troubleshooting step, follow step 7 in the link to return the computer to a Normal startupmode.

• Computer Vista will not complete start up once the updates have been installed

  Office worked well on 20 January, until the update when you restart it should start going to black screen with cursor. I tried to fix it, but it does not work. I tried the system restore to an earlier date but gives the error. Does anyone have ideas, which is false.

  Thank you

  Lisa,
  At this point if you have a way to back up your data, I suggest that do you so as soon as possible.  Start the XP that you have installed.  Then copy all your data from the original Windows folder to an external drive or a DVD.

  Then, to try to make this repair, boot from the XP disc and select the recovery option.  This will start you in the recovery console prompt.  From there, you can then run the commands to replace the sam file.  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer Vista will not format DVD RW drives more

  I have problems with my DVD disc burning, windows formateront is no longer my DVD - RW discs but will format my DVD-R discs, what can I do as I don't like having to use disposable DVD discs all the time? I'm just a learner so im very confused, please help me... thanks

  * original title - formatting issues. Windows reformatted is no longer my DVD - RW discs.*

  Hi nicky271,

  ·         Did you format the disc earlier?

  ·         Remember to make changes?

  ·         What happens when you try to put in the form of these discs?

  Step 1: We will uninstall the DVD drive in Device Manager and reinstall. Automatically search for updates to the firmware on the manufacturer's Web site.

  a. click the Start button and then right click on computer. Click on properties.

  b. click on Device Manager.

  c. now, expand the CD-ROM/DVD-ROM drives, click with the right button on the CD-ROM/DVD-ROM drive and click on uninstall.

  d. restart the computer.

  Step 2: Log on to the manufacturer of the DVD drive and install the latest updates from driver\firmware.

• Computer laptop 32 bit Vista will not shareprint with XP Office officejet v40 printer. Help, please

  I have read forums and tried everything for 4 days without luck.

  I'm trying to print from my 32-bit vista laptop to my printer of office xp... an old officejet v40 printer.

  The office prints well on this printer from xp desktop attached and I named shared printer.  All security and firewall disabled. I started at least 20 times and have tried to install unsuccessfully

  It seems that the HP driver Web page has a driver for vista, BUT the instructions are only if you hang the printer directly with the USB... No shared networking. I always thought that you could just download the dirver to the computer and it turns when you go to install it. I made for the devil to the hook to the top of my computer vista laptop directly to the printer and it installs and works fine... BUT I want it in a network or shared... no USB.

  Also, if I go to "Add a network printer" and select the printer in office shared in the list, it will be in my control panel as a printer on my laptop, but when I hit print, I get the pop box, which allows you to set the preferences, print etc, and when I hit print again, the small pop-up box flashes on for a second that it's printing paper... but no printing. Instead of this, when go to see what happened to the list of document status, I see the State of the document listed as error - printing"

  I don't know if I have vista for this printer driver in my laptop or what? I'm totally confused by the present. I read somewhere that there is no way for a computer vista laptop to print over the network to this HP printer while the printer is connected directly to a computer running XP? Is this true?

  I rarely if ever gave to be beaten by computer problems... but this one had me done bankruptcy for the third time and about to give up. Any help would be appreciated.

  THIS TIME IT WORKED! After several months of not being able to print from my computer vista laptop for my v40 OfficeJet (which is connected to my desktop XP) I decided that I would give it one more try. I used once more Bob of the 2nd ad above, as well as suggesion Eddy's instructions to select "New Port" when you arrive at the end close to Bob's instructions. THIS TIME IT WORKED! I think I'm out track somewhere when I tried to do this several months ago. In any case, I thought that I have would expand a bit on what Bob wrote just in case there's someone that who needs a little more in detail. (For a beginner, even the smallest thing can be stumbling blocks if you have never done this kind of thing before)

  On your computer vista laptop, go to printers and Control Panel. When you click the Printers icon you can click on add printer and select Add local printer (it even if it is not a local printer, but a printer that is connected to your desktop computer in another room) Ok... Then select "Use the existing Port" LP1. Then you select your printer from the list and click on it to install the driver. I think that you then click FINISH. (No you are not really over, so don't bother is not clicking on this Test Page again). Once you click FINISH, you will automatically be on the screen that shows the printers you have installed on your laptop. for help. You will then see the the OfficeJet v40 as the printer that you just installed. Highlight and right click. Then select "Run as Administrator". That will open a submenu where you and then click Properties. Then click on Ports, Add Port. Select "Local Port" and click "New Port" (as Eddy proposed). A small screen will appear where you enter now the \\NameOfPrinterYouArePrintingTo\ShareNameOfThatPrinter once you do this and click on apply and OK, you will be brought to a final screen where you will notice that the box LP1 is more verified. Place a check mark was automatically placed in the new port that you just created above IE name\sharename.  YOUR DONE!