Configure asa5520 help

Similar Questions

• E HP6830 all-in-one: with disabilities... network configurations please help

  I'm having the same problem.  Just Bough this printer 2 weeks ago staples.  Everything I select, wifi, network, fax even scanning e-mail I receive a message indicating "built in the configuration of the network have been disable contact administrator or the person who created the printer.»

  Help, please.

  Hi @Babyd1967,

  Welcome to the Forums of HP Support! I understand that you can not access anything whether it's on the screen of the printer without administrator rights. I want to help you solve this problem. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  I can send you the reset of the printer in a private message. This should take care of this problem.
  In the forum next to your handle name simply click on the envelope to see.

  Please let me know the results and if there is anything else I can help you. Thank you.

• stuck on configuring updates, help

  I upgraded my pc, it is stuck on configuring updates 1 of 3, 0%, which can do to restore it, I have no cd boot and you cannot get into safe mode, I am running vista, please help

  Hi Julie1212,

  I suggest to organize for a Windows Vista disc that is the same edition as it is installed on your computer, then try the steps in the Microsoft Knowledge Base.

  An update is not installed successfully when you try to install the update in Windows Vista and Windows 7

  http://support.Microsoft.com/kb/949358

  I hope this helps.

• How to configure ASA5520 of Checkpoint IPsec tunnel configuration

  Hi guys and under tension, a lot of it!

  I have a problem, I set up an IPsec tunnel between my ASA5520 at a Checkpoint Firewall (PE) CONFIG below (not true FT)

  network of the ASA_MAPPED object

  4.4.4.0 subnet 255.255.255.0

  network of the CHECKPOINT_MAPPED object

  5.5.5.5.0 SUBNET 255.255.255.0

  OUT_CRYPTO extended access list permit ip object ASA_MAPPED object CHECKPOINT_MAPPED

  Crypto ipsec transform-set ikev1 CHECKPOINT_SET aes - esp esp-sha-hmac

  destination NAT (INSIDE, OUTSIDE) static source ALLNETWORKS(10.0.0.0/16) ASA_MAPPED CHECKPOINT_MAPPED of CHECKPOINT_MAPPED static

  NAT (INSIDE, OUTSIDE) source of destination ALLNETWORKS(10.0.0.0/16) static ASA_MAPPED static 4.4.4.11 5.5.5.11

  card crypto OUTSIDE_MAP 5 corresponds to the address OUT_CRYPTO

  OUTSIDE_MAP 5 set crypto map peer X.X.X.X

  card crypto OUTSIDE_MAP 5 set transform-set CHECKPOINT_SET ikev1

  card crypto OUTSIDE_MAP 5 defined security-association life seconds 3600

  CHECKPOINT_MAP interface card crypto OUTSIDE

  tunnel-group X.X.X.X type ipsec-l2l

  tunnel-group ipsec-attributes X.X.X.X

  IKEv1 pre-shared-key 1234

  ISAKMP crypto 10 nat-traversal

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  preshared authentication

  aes encryption

  sha hash

  Group 5

  life 86400

  IPsec Tunnel is in place and I can access the server on the other side via the beach of NATTED, for example a server behind the checkpoint with the IP 10.90.55.11 is accessible behind the ASA as 4.4.4.11, the problem is that I have never worked on a Checkpoint Firewall and servers/Server 4.4.4.11 that I can't connect to my environment to that checkpoint is configured with a Tunnel interface that is also supposed to to make NAT because of the superimposition of networks, at one point, I added an access to an entire list and bidirectional routing has been reached, but I encountered a new problem, I could not overlook from my servers public became unaccessecable, since all traffic was encrypted and get dropped to VPN: ipsec-tunnel-flow... for now the Tunnel is up and I can access the server via NAT 4.4.4.11, but can't access my internal servers. What did I DO WRONG (also, I don't have access to the Checkpoint Firewall (PE)) how their installation would be or how it should be to allow bidirectional routing?

  ========================================================

  Tag crypto map: CHECKPOINT_MAP, seq num: 5, local addr: X.X.X.X

  Access extensive list ip 4.4.4.0 OUT_5_CRYPTO allow 255.255.255.0 5.5.5.0 255.255.255.0

  local ident (addr, mask, prot, port): (4.4.4.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (5.5.5.0/255.255.255.0/0/0)

  current_peer: X.X.X.X

  #pkts program: 3207, #pkts encrypt: 3207, #pkts digest: 3207

  #pkts decaps: 3417, #pkts decrypt: 3417, #pkts check: 3417

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 3207, model of #pkts failed: 0, #pkts Dang failed: 0

  success #frag before: 0, failures before #frag: 0, #fragments created: 0

  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

  #send errors: 0, #recv errors: 0

  local crypto endpt. : X.X.X.X/0, remote Start crypto. : X.X.X.X/0

  Path mtu 1500, fresh ipsec generals 74, media, mtu 1500

  current outbound SPI: 5254EDC6

  current inbound SPI: 36DAB960

  SAS of the esp on arrival:

  SPI: 0x36DAB960 (920303968)

  transform: aes - esp esp-sha-hmac no compression

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 19099648, crypto-card: CHECKPOINT_MAP

  calendar of his: service life remaining (KB/s) key: (3914999/3537)

  Size IV: 16 bytes

  support for replay detection: Y

  Anti-replay bitmap:

  0 x 00000000 0x0000000F

  outgoing esp sas:

  SPI: 0x5254EDC6 (1381297606)

  transform: aes - esp esp-sha-hmac no compression

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 19099648, crypto-card: CHECKPOINT_MAP

  calendar of his: service life remaining (KB/s) key: (3914999/3537)

  Size IV: 16 bytes

  support for replay detection: Y

  Anti-replay bitmap:

  0x00000000 0x00000001

  unless I include any any on my access-list and the problem with that is  that my Public servers then get encrypted from the OUTSIDE interface  unless you know of a way to bypass the VPN
  
  

  No, u certainly shouldn't allow 0.0.0.0 for proxy ACL. Again, your config is very good. In addition, package account, this show that traffic is going throug the tunnel in two ways:

  #pkts program: 3207

  #pkts decaps: 3417

  Also, looking at the meter, I can guess that some of the traffic comes from the other site, but does not return back (maybe that's where you can not connect from behing Checkpoint). If you say that 0.0.0.0 solved the problem, are there no other NAT rules for subnet behind ASA, so the server IP, for which you are trying to connect behind the checkpoint, translates into something else (not the beach, included in proxy ACL), when to come back?

• Configuration AnyConnect helps Juniper SRX

  Hello and thanks for reading.

  This is a new Setup and I need support. I have not supported in TAC, but it has not proved effective.

  Internet - > Cisco ASA-> Juniper SRX-> extreme L3 SW-> APC

  What I've done so far is to install the latest images AnyConnect - anyconnect-macosx-i386 - 3.1.09013 - k9.pkg

  and running asa916-6 - k8.bin

  Please help with the Setup, with the IP space indicated, I have the last byte available for space public.184,.185, I drew the network in question. See photo.

  Untitled.PNG

  

  On the certificate, you can browse to your ASA outside interface and, using your browser ability inspection certificate, download the certificate to your local host. You can then import this certificate in the trusted root certificate authority (CA) store (or the equivalent on the non-windows hosts) and it will be not reliable for future connections. This may or may not be feasible by the technical knowledge of end users. For this reason and others, most enterprise deployments choose to use a problems of certificate by an established CA.

  For the issue of the domain, you must add your local domain if you / them to be added to the DNS suffix search list when a VPN connection is established.

• Bangin blackBerry smartphones ' my head against a wall re: Internet e-mail configuration. Help, please! I'm desperate.

  Argh...

  Have been trying for days to set up my email of internet.

  I bought an unlocked 8310 (AT & T) curve for my T-mobile account.  Everything works so far, including browsing the web, but I can't configure my Internet email.

  There is absolutely no icon on the phone to do this, I searched all the options that was suggested to me.  The only option I have is to set up an Email from the company, which I did not.  I have been in discussion with AT & T and TMobile and have entered my PIN and IMEI code on both sites to try to set up, with nothing working.

  All the ideas for the poor ole' me?

  Thank you

  Sarah

  

  Phew... I had figured it out.  TMobile sent me incorrect service for my telephone books.  Thanks for responding!

• Helps the acquisition of photon counter data using LabView 12

  Hey all,.

  Student graduate Chemistry here new to LabView and are looking for some help moving in the right direction.  I'm looking for help with connecting my meter to 12 LabView for data acquisition of trace-fluorescence photon PerkinElmer SPCM-AQR-14 (now owned by Excelitas Technologies).  I just want to be able to acquire number of photon counts vs. time.  Currently, I installed a PCI-6601 and use a BNC-2121 to connect the BNC of the sensor output.  The detector has a pulse output digital TTL with 30 ns pulse width, and by contacting technical support on this issue, I was told that this pulse width was too short to always detected by the 6601, but can still go ahead and give it a try.  Basically, if everyone is familiar with how to start with this configuration, ANY help would be greatly appreciated.  As I said I'm all new to LabView and am currently spend all my spare time reading manuals and help files.

  Please let me know if you need any kind of information to make me understand what I'm doing.

  I would say something like this:

  

  A measurement period the registry account out of the entrance of the samples as well as gives the meter.  You will basically measure the 'period' of your sample clock fixed regarding ticks of the external photon signal.

  According to the downtime, you may need to re-read several samples per loop so that the software can keep up with the incoming data.  Also, the first sample is not useful because it represents the County between the software from the task of entry of the meter and the first clock signal - you should disregard/erase the first sample (or if you want you can set up a trigger to begin arms).

  To do the same thing by using an edge County task would require using both the sample clock AND a counter reset signal - this not is not supported on 6601/6602 (even if it would be possible to set it up that way on a device of STC - 3 as a series of X).

  Best regards

• Basic configuration of TFS 2012 fails on the data layer.

  Hello

  I have a new installation of sql server 2014 and has the last update 7 on it.

  Installed TFS 2012 update 4 and I tried the basic configuration to help start Wizard.

  I am getting...

  "TF255146: Team foundation server requires SQL server 2008 Rs (10.50.1600) or higher." The SQL server instance xxxxxxx you provided is the version 12.0.2495.0.

  I couldn't find much online research help. Any ideas how to solve this problem?

  Thank you

  Vinciane

  
  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Windows XP, why she is frozen in the configuration?

  downloaded updates. 3/3 full. the configuration. 0 0 full. rotating laptop market by itself. SINCE THE NIGHT LAST. How is it? tried to start it in safe mode. updates always takes over and stops and starts up the laptop. Why is - that it is frozen in configuration? Help.

  Hello

  1. the updates are facing this problem with?

  2. do you have service pack 3 installed on the computer?

  This problem may occur due to the interruption of Non MS & software services that run as AV, firewall.

  Please follow the links below to solve the problem. Execute the method 1 and 2 If you are unable to boot to the desktop.

  Method 1

  How do I recover from a corrupted registry that prevents Windows XP startup

  http://support.Microsoft.com/kb/307545

  Method 2

  Repair install of Windows XP by starting your computer from the Windows XP CD

  Note: If Windows XP was preinstalled on your computer, you may need the installation CD to reinstall. Contact the manufacturer of your computer to make sure that you have the CD for a repair installation.

  To reinstall Windows XP by starting your computer from the Windows XP CD, follow these steps:

  a. Insert the Windows XP CD in your computer's DVD or CD drive, and then restart your computer.

  b. When you receive the message "Press any key to boot from CD" on the screen, press a key to start your computer from the Windows XP CD.

  c. the following message on the Welcome to Setup screen is displayed:

  This part of the Setup program prepares Microsoft Windows XP to your computer: to set up Windows XP now, press ENTER.

  To repair an installation of Windows XP using the Recovery Console, press R.

  To quit Setup without installing Windows XP, press F3.

  d. press ENTER to set up Windows XP.

  e. on the Windows XP Licensing Agreement screen, press F8 to accept the license agreement.

  f. make sure that your current installation of Windows XP is selected in the box and then press R to repair Windows XP.

  g. follow the instructions that appear on the screen to reinstall Windows XP.

  After repairing Windows XP, you may have to reactivate your copy of Windows XP.

  Method 3

  I suggest you perform a scan of disk checking on the hard disk to check for any errors with it.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Important: When running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area so all available data on this risk to be lost

  I hope this helps.

• Cannot configure ip multilayer switch (packet tracer) support

  Hello

  I work at tracers of package with this network:

  

  All PC's are on the same vlan (vlan 100) and my DHCP server has an IP address on a different VLAN (vlan 500).

  I did an interface for each vlan on my multilayer switch and now I want to configure a helper ip for my clients (vlan 100).

  But when I try, the command does not exist:

  

  I don't understand what I'm doing wrong.

  Any ideas?

  Hello.
  It could be your version of Packer Tracer, I use 6.2.0.0052 student edition and when I start a 3560-24PS switch you did:
  Switch > en
  Switch #conf t
  Enter configuration commands, one per line. End with CNTL/Z.
  Switch (config) #int vlan 1
  Switch(Config-if) #ip it
  Switch(Config-if) #ip he?
  Hello-interval of assistance-address
  Switch(Config-if) #ip help
  Switch(Config-if) #ip helper-address?
  Destination IP A.B.C.D address

  Is it possible for trace you to download your lab or refresh your packet version?

• Need help installing a Raid0 in Win7Pro disk management.

  I had a raid but only one drive died and I'm trying to get a new will raid0.  I have an SSD for the boot drive and two new Sata Seagate 3TO disks for the raid.  They are installed and the Intell Rapid Storage Technology Software sees them and I used that to create a new switched-on and both drives are chosen as members.

  Now I go to disk management in Windows, but I forgot what to do now. Initialize disks, make them dynamic with GPT partitions and choose them as striped readers?  Just not sure of the procedure.  I have a motherboard Asus P9X79 WS with UEF Bios.

  Personally, after seeing the problems, I use raid, except that using a third party hardware raid card and for redundancy, I more than two disks, at least one more of a resumption of the fall-over

  A decent raid card costs about $500

  RAID 0 is a striped raid configuration

  Help manual Asus has instructions

  or http://www.howtogeek.com/howto/36504/how-to-create-a-software-raid-array-in-windows-7/?PageSpeed=noscript

  I don't know about whether the raid controller you are using supports a resumption of the fall-over with additional disks

• ASA5520 routing?

  I connected my asa5520 as:

  CAT6 (port Access)-> ASA5520 (outside)

  CAT6 (trunk port)-> (inside)-> vlan101 and vlan 102

  Configure asa5520 as:

  interface GigabitEthernet0/0

  nameif inside

  security-level 100

  no ip address

  !

  interface GigabitEthernet0/0,101

  VLAN 101

  No nameif

  no level of security

  10.1.1.1 IP address 255.255.255.0

  !

  interface GigabitEthernet0/0,102

  VLAN 102

  No nameif

  no level of security

  10.1.2.1 IP address 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif outside

  security-level 0

  IP 10.1.3.9 255.255.255.0

  on the cat6, I add static route:

  Route IP 10.1.1.0 255.255.255.0 10.1.3.0

  Because I don't want to use Protocol ospf/rip road. Can I use static route? If so, how can I do it?

  Any comments will be appreciated

  Thanks in advance

  I think your static route in Cat6 must point to the IP of specific next hop of 10.1.3.x instead of 10.1.3.0 (it is subnet ID).

  Anyway, you can still use static in ASA. It supports RIP OSPF.

  To configure static on ASA to Cat6, use (example):

  Route outside 0.0.0.0 0.0.0.0 10.1.3.1, or

  external route 10.1.1.0 255.255.255.0 10.1.3.1

  * assuming 10.1.3.1 is your IP of the interface Vlan Cat6 facing ASA outside interface

  Otherwise, from Cat6, road to ASA inside VLan 101:

  Route IP 10.1.1.0 255.255.255.0 10.1.3.9

  But the other condition is that you must configure static nat for the Vlan101 to talk to the segment of the outside, inside like:

  static (inside, outside) 10.1.1.0 10.1.1.0 netmask 255.255.255.0

  This will allow users/guests of the outside/Cat6 side to talk to Vlan101 internal hosts.

  HTH

  AK

• Help, please! Connected to the VPN, but cannot access internal servers.

  Hi friends,

  I'm a newbie on vpn stuff, I set up a base on a Cisco ASA 5505 vpn by using ASDM, and I was able to connect to it.  However, I can't ssh or RDP to one of the servers in the House after that I connected to the vpn.  Here is the configuration.  Help, please!

  ASA Version 8.2 (5)

  !

  hostname sc - asa

  domain abc.com

  enable the encrypted password xxxxxxxxx

  xxxxxxxxx encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain OpenDNS.com

  sc-pool_splitTunnelAcl-list of allowed access standard 192.168.1.0 255.255.255.0

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd dns 208.67.222.222 208.67.220.220 interface inside

  rental contract interface 86400 dhcpd inside

  dhcpd abc.com domain inside interface

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL encryption rc4 - md5, rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1

  WebVPN

  abc group policy - sc internal

  attributes of the strategy of group abc - sc

  value of server DNS 208.67.222.222 192.168.1.3

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value abc-sc_splitTunnelAcl

  field default value abc.com

  a001 xxxxxxxxxxx encrypted password username

  a002 xxxxxxxxxxx encrypted password username

  username a003 encrypted password privilege 0 xxxxxxxxxxx

  a003 username attributes

  Strategy Group-VPN-abc-sc

  a004 xxxxxxxxxxx encrypted password privilege 0 username

  a004 username attributes

  Strategy Group-VPN-abc-sc

  a005 xxxxxxxxxxx encrypted password username

  a006 xxxxxxxxxxx encrypted password username

  username privilege 15 encrypted password xxxxxxxxxxx a007

  remote access to tunnel-group abc - sc type

  attributes global-tunnel-group-abc - sc

  address sc-pool pool

  Group Policy - by default-abc-sc

  tunnel-group abc - sc ipsec-attributes

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:e7df4fa4b60a252d806ca5222d48883b

  : end

  Hello

  I would suggest you start by changing the pool VPN to something else than the current LAN network and see if that helps

  These should be the configuration required to achieve this goal

  • First remove us pool setup VPN VPN
  • Then we delete the VPN Pool and create again with an another address space
  • When then attach this new Pool of VPN again to the VPN configuration
  • In the last step, we add a NAT0 / exempt for this new pool VPN NAT configuration and remove the old ACL line for the former group of VPN

  attributes global-tunnel-group-abc - sc

  no address-sc-swimming pool

  no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  IP local pool sc-192.168.100.100 - 192.168.100.110 mask 255.255.255.0

  attributes global-tunnel-group-abc - sc

  address sc-pool pool

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.100.0 255.255.255.0

  No inside_nat0_outbound access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240

  -Jouni

• ASA5520 and RV042

  Hello

  I configured ASA5520 and RV042 for IPSec VPN tunnel site-to-site.

  Get tunnel only connected, but no ping, no traffic between the two networks to end.

  Network:

  =======

  192.168.113.0/24---192.168.113.6 - ASA - IP address public, static - Cisco 2821 - Internet

  192.168.10.0/24---192.168.10.1-RV042---Adresse IP public, static - Cisco 2821 - Internet

  ASA5520 config:

  ----------------------

  name of 192.168.10.0 VPN

  !

  interface GigabitEthernet0/1

  NET nameif

  security-level 100

  IP 192.168.113.6 255.255.255.0

  !

  access extensive list ip VPN 255.255.255.0 com_cryptomap allow 192.168.113.0 255.255.255.0

  access extensive list ip 192.168.113.0 com_nat_outbound allow VPN 255.255.255.0 255.255.255.0

  card crypto com_map0 1 match address com_cryptomap

  card crypto com_map0 1 set counterpart x.x.x.x

  com_map0 card crypto 1jeu transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  com_map0 map 1jeu phase 1-mode crypto aggressive

  com_map0 card crypto of com interface

  crypto ISAKMP enable com

  crypto ISAKMP policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 10

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  attributes of Group Policy DfltGrpPolicy

  Protocol-tunnel-VPN IPSec

  IPSec-attributes tunnel-group DefaultL2LGroup

  NOCHECK Peer-id-validate

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  pre-shared key *.

  NOCHECK Peer-id-validate

  !

  RV042 Setup is very simple.

  No particular reason or config missing?

  Crypto ACL on the SAA has been configured in the reverse.

  Currently, we have:

  access extensive list ip VPN 255.255.255.0 com_cryptomap allow 192.168.113.0 255.255.255.0

  It should be:

  access extensive list ip 192.168.113.0 com_cryptomap allow VPN 255.255.255.0 255.255.255.0

  Disable the tunnel after the changes and let us know how it goes.

  Please let us know the output of the following if it still does not:

  See the isa scream his

  See the ipsec scream his

• Cannot install iTunes, error: error occurred during installation before iTunes could be configured.

  Original title: I Tunes APP.

  I'm unable to start installation of iTunes on my pc

  I have download the app, then during the installation, I get this message

  Errors occurred during the installation before iTunes could be configured

  Help, please

  NOTE: I had iTunes on my menu START but it deleted by accident.  It's not in my recycle bin while I was trying to install the latest version

  Hi LisaSims,

  According to your statement "I had iTunes on my menu START but it deleted by accident." "It's not in my recycle bin while I was trying to install the latest version. If you just delete the shortcut on the start screen that does not remove the actual program from your computer. Check "Programs and features" If iTunes is still installed. To do this, see the following steps:

  (a) press "win key + W" simultaneously to bring up the search interface.

  (b) type 'Programs and features' and press enter on the keyboard.

  (c) under "Programs and features" list check whether "iTunes" in the list. If so, then iTunes is still installed on your computer.

  Navigate to the following location and check to see if the iTunes folder is listed:

  If Windows is the 32-bit version check: "C:\Program Files\iTunes\".

  If Windows is 64 bit version check in: "C:\Program Files (x 86) \iTunes\.

  If the problem is specific to iTunes and you have already tried uninstall and reinstall as suggested by 'Andre Da Costa' then contact support for assistance to install iTunes.

  https://discussions.Apple.com/community/iTunes

  Hope the helps of information. Keep us updated with the status of the issue.