connecting s switch CISCO 2500 with a Windows 7 laptop?

Similar Questions

• I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  Try this below and see if it help you.

  http://support.Microsoft.com/kb/871122

• connection of switches cisco and hp with gbic

  I have a new Cisco 2960 x and an existing HP 2910al. I am OK with the set up, I have the hp interface and Cisco all the time with copper but this is the first that I had with fiber. I know that Cisco switch will a Cisco gbic (can move only with service not taken into charge-transmitter/receiver) and HP will want a Gbic hp (new Hp operating system only works with HP Gbic).

  So here's the question, Cisco Gbic and Hp Gbic of interconnection? I guess Yes, but want to ask before you buy and know that they don't.

  As long as they are of the same wavelength (like SR to LR to LR or SR) Yes they do.

• Connect 2 switches SG200-26 with two VLANS separated

  B "H".

  Well, I'm going to cry uncle and ask the community of cisco to help here... Here's what I'm trying to accomplish.  I have two cabinets in a data center with four available cross connect cables.  I want to put in place two discrepancies between the two switches which will each be a vlan through to the other.   My vlan by default contains all my servers on it (10.0.0.0/8) and my backup vlan (192.168.200.0/24) will only be used for data backups and iscsi traffic.  For the moment, I have a cable connecting the two switches and it works very well for the vlan by default.  When I add a second cable and set it on vlan 200, no matter what I try settings it just does not pass traffic.  I'm sure I'm doing something wrong, stupidly, but well, I never claimed to be a networking expert, that's why I'm here asking for help!

  I have made several attempts to get the second connection works, marked, unmarked, trunk, access, etc.  Can someone be tell me is this the real solution, or point me to the documentation, so I can solve this problem?

  Thanks in advance!

  Hello Yitz'har,

  SG 200 switch does not support EMU, PVST and PVST +. None of the products of small businesses currently support any proprietary protocol which is not IEEE or equivalent. The exception to this idea is COP which was added about 18 months in the LWA 1.1 releases to better integrate voice, onplus solutions and interact with business networks.

  Work that we discussed yetserday in your case is to disable the covering tree generally define the bpdu filtering.

• Cannot connect the switch Cisco Cisco SG300 - 28 p spend and traffic through VLANS

  Try to connect the Cisco SG300 - 28 p switch to another switch and proceed 2 VLANS between them.  Not doing any circuit.  If I connect a computer to the port on the SG300 - 28 p I can access the VLAN 2 and take a DHCP address. However, when I connect to another switch on the port and connect it to a port on another switch secondary I am unable to access VLAN 2 and pull an IP address.  I checked that the works of secondary switch (WS-C3560G-48PS-S) connected to the other 3500 s, but not this latest SG300 - 28 p.  Here's the configuration for both, I'm leaving areas that shouldn't matter and add if necessary.  Try to connect the SG300 - 28 p Port 26-WS-C3560 Port 1 port.  Once again, if I connect a computer to port 26 on the SG300 - 28 p I access the VLAN 2 as expected, but not when I connect to channel 2 on the secondary switch.

  Cisco SG300 - 28 p

  !
  interface vlan 1
  Internet name
  !
  interface vlan 2
  LAN name
  IP 172.20.5.11 255.255.0.0
  no ip address dhcp (this is the VLAN I'm moving)
  !
  interface vlan 3
  private name
  !
  interface vlan 4
  name of Nortel
  !
  interface vlan 101
  name Video_Project
  !
  interface gigabitethernet26
  Description VLAN2-ACCESS-CISCO3500
  switchport mode access
  switchport access vlan 2 (this goes to port 1 on the other Cisco 3500 switch to provide access 2 VLAN)

  Cisco 3500

  !
  interface Vlan1
  NATCO Internet description
  no ip address
  no ip route cache
  no ip mroute-cache
  !
  interface Vlan2
  NATCO LAN description
  IP 172.20.5.13 255.255.0.0
  no ip route cache
  no ip mroute-cache (this is the VLAN I'm moving)

  !
  interface Vlan3
  Description LHPrivate
  no ip address
  no ip route cache
  no ip mroute-cache
  !
  interface GigabitEthernet0/1
  switchport access vlan 2 (this is the port that I connect to the SG300 - 28 p)

  !
  interface GigabitEthernet0/2
  switchport access vlan 2 (this is the port I hang my computer to and trying to access VLAN 2 other switch)

  Hello

  Yes, STP is the problem here. As you can see on your release of the Cisco 3500 switch, port Gi0/1 is BKN (The FEW is a shortened form of "Broken").

  This is caused by an incompatibility of versions PLEASE used between the two switches. Small businesses (including series SG300) switches are use legacy STP or Rapid STP (your case), but uses templates to business (such as catalyst 3500) PVST + (each VLAN spanning tree version of STP).

  Two versions between group of switches are compatible only under certain conditions. Important condition is that the two switchports needs to use a VLAN 1, vlan access/native and not any other number VLAN.

  It is to make your communication work, you must:

  • disable the STP at least 3500 Cisco switch:
    • on overall global (Switch (config) # no vlan spanning tree 2)
    • or by the base interface (switch(config-if) # no vlan spanning tree 2)
  • change the configuration of your connection between two switches by following the path:
    • change the switchport trunk (trunk switchport mode) mode
    • do 1 VLAN as native vlan (vlan switchport trunk native 1)
    • Towing VLAN 2 as vlan tagged on that Stump (switchport trunk allow vlan add 2)

• What XBOX 360 controller work with a Windows Vista laptop?

  I need to know what Microsoft controller buy who will work with NBA 2 K 10 for PC.
  My computer is a HP Pavilion dv6830us Entertainment Notebook PC.

  I also need to know how and where to buy a new graphics card or how to upgrade a so that the game works more smooth.

  May need a complete redesign of some things and hoped that someone would be able to help me with step by step instructions, because I am panicking about it. Could be a waste of $ 20 if I can't understand something here, given that GameStop does not accept returned PC games. :-/

  A wired remote will work.  A wireless will work also, but only with the "Xbox 360 Wireless Gaming receiver for Windows".  Assuming that the game you are trying to use it with supports controllers. Paul Smith - MVP for Windows desktop experience... I crawled off NNTP - for now. Detachment Aldershot, United Kingdom. On the internet atwindowsresource.net and dasmirnov.net. Please post back to let us know what works and what does not. :-)

• Wireless keyboard Apple ceased to connect to the Windows 7 laptop

  I bought an Apple Wireless Keyboard 3 months ago and it works perfectly with my Windows 7 laptop until today - to halfway through editing a word document, it stopped working and my laptop makes the sound as a USB is plugged or removed.

  While I tried to remove the device and add it again. Several times. No luck. Then I deleted the device, rebooted the computer and re-added. Still no luck. Whenever I added, it brings to the top of the screen to enter the pairing code and that everything goes well and it appears in the printers and devices window. But it is grayed out, as if it was there but not there.

  I tried new batteries, but it made no difference. The keyboard still works perfectly with my iPad.

  When I turn on the keyboard, it displays a green light that blinks twice then pause then blinks twice again on repeat (according to the Apple Support Online, it's the device is detectable signal).

  I've also updated all Bluetooth drivers on the laptop, but displayed as up to date.

  Of course, Apple in charge cannot help me, and phone support from Microsoft could not be.

  Any suggestions? :)

  Hello

  Maybe there is an updated driver for the keyboard which caused the stoppage of work,

  If you go to the start menu and type "devmgmt.msc" into the search bar, it will bring you to the Device Manager.

  Look for the device in the list, it must be under keyboards, but because it seems to not be recognized, it can be in the tab of the unknown devices.

  If you cannot find the device, right click and select Properties, then go to the driver tab.

  From there, you can try to roll back the driver if this option is available, or update the driver to see if you can get a working one.

  Another thing to do in Device Manager is to click with the right button on the computer on top of the list, then choose the "Scan for hardware changes" and there may be for the device as well.

• Controller of domain and DNS behind RRAS without VPN connected directly to the internet with a Cisco router

  I hava a ME Cisco 3400 with physical single port available for a cable connection.

  The ISP give me an IP address interface = 89.120.29.89 to act as a gateway to the IP Address of the host, which is provided for in the order 89.120.29.90.

  The host computer is a dual Xeon computer with two NICs for LAN and WAN.

  Fields of application: to install a windows 2008 R2 between public and private network server.

  Even though I know it's not recomanded, I put the DNS role and directories Active Directory roles installed on the same computer, the computer above, (I do not have enough computer for roles different place on different computers)

  The desired configuration:

  To have installed with his roles behind a WS2008R2 has RRAS. without a VPN.

  b with VPN

  and for WAN access for the client computers of the private LAN Windows 7 OS. (The basin of LAN address 192.168.0.1 - 255).

  First step : to have internet access in the browser (I use Google chrome) (without taking into account the DNS and AD)

  Network configuration:

  Map NETWORK WAN, at the top of the stack of liaison in the Control Panel/network connections and sharing:

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  OK, I can browse the internet.

  Second stage. (Consider DNS and Active Directories)

  DNS instaled role for this computer.

  AD installed as a global catalog.

  NETWORK WAN server that is directly connected to the Cisco router:

  Conection area 3

  Properties:

  Client for Microsoft Netwaork: not verified

  Network Load Balancing: not verified

  File and shared printer: not verified

  QoSPacketScheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: not verified

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: not verified;

  Use this connection DNS suffix in DNS registration: not verified;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: don't check;

  Disable NetBios on TCP IP: checked;

  Connection to the local network 2

  Properties :

  Client for Microsoft Netwaork: checked

  Network Load Balancing: no

  File and shared printer: checked

  QoS Packet Scheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4 checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  NETWORK LAN CARD: 192.168.0.101

  Mask: 255.255.255.0

  Gateway: 192.168.0.1

  under Advanced tab:

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: check;

  Disable NetBios on TCP IP: not verified;

  Install RRAS as NAT (NAT) under any condition imposed by DHCP(not installed) in ideea that RRAS will generate the private IP address of the DHCP allocator.

  In any case, for the beginning, I have a fix IP, do not get IP automatically.

  At this point, it gets the configuration simple posible for RRAS follows:

  3, LAN connection that corespond to the WAN interface IP:

  "NAT configured for the following Internet interface: Local Area Connection 3.
  The clients on the local network will assign the IP addresses of the following range:

  network address: 192.168.0.0. netmask 255.255.0.0.

  After Windows RRAS are open:

  The Network Interfaces tab:

  NICs are enabled and connected;

  UAL remotely & policies:

  Launch NPS,

  on the NPS server tab:

  Allow access to successful Active Directory directories:

  Properties: authentication: port 1812,1645

  kept port 1813,1646;

  on the accounting tab: nothing;

  under NPS policies:

  Grant permission for the RRAS server under builin\Administrator of the accounts;

  On strategy and the type of server unspecified (NAT do not exist as an entry in the drop-down list server dwn)

  under the static road: nothing;

  under the IPv4 tab or both are there(there IP) and are up

  under NAT

  Connection to the local network 3: public interface connected to the internet

  enable NAT on this interface:

  under the address pool: ISP addresses public;(two addresses)

  under the terms of service and the ports: Web server: http 80.

  (I have I have a static IP address for the client computer in mind, I set up a single customer).

  At the client computer :

  configured as domain customer and added to the users AD and computer AD

  logon to the domain:

  Local Area Connection

  Properties:

  Client for Microsoft Netwaork: checked

  Network Load Balancing: not verified

  File sharing and printer: checked

  QoS Packet Scheduler: checked;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 192.168.0.101

  Mask: 255.255.0.0

  Gateway: 192.168.0.1

  DNS: (auto-add the same to the local machine).

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: checked;

  Disable NetBios on TCP IP: not verified;

  right now the 192.168.0.101 client cannot connect to internet through RRAS.

  ;

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Help with M6348 connecting to a Cisco network

  Hello

  Can someone help me with best practices by putting R710 via a M6348 stacked with a cisco network.

  Our configuration is the following

  M1000e

  2 x 1 GB pass-through fabric a

  2 x M6348 wired in a pile in the B fabric

  6 x popular R710 with four NIC ports in the fabric B (3 are general purpose servers, 3 are Hyper-V servers in a cluster)

  Cisco network

  For most of the Cisco 3560 switches

  20 VLAN (1 per building) configured, mainly for the isolation of traffic (VLAN 300-320)

  What (I think) that we want to

  The M6348 connect to the core network in a SHIFT (4 x 1 GB ports. Can it be divided 2 ports each of the stacked M6348?)

  Have a mapping of right for 1-3 to VLAN 301 R710

  Configure R710 4-6 for access to all VLANS for the Hyper-V hosts can be placed on the VLAN correct

  Use the fabric for the connection to the San

  Network management is carried out by a third party (we are unable to change this) and they claim that they are unable to connect Cisco/Dell!

  We are server guys, guys network no, so something stupid (especially for Cisco to give to our management company) would be appreciated.

  We tried to configure the switches in Simple mode, using a Dell deployment guide, but all we seem to get is the default VLAN to all ports on the switch 1 battery, but no other VLAN and no active port 2 in the stack.

  I've probably missed lost info on and were not very clear, so if more info is needed, please get back to me.

  Thanks in advance for the help

  Rich

  Thanks for the information updated, actually, this confirms that the problem is with the connection to the Cisco switch. Is that what we tried a general link, instead of trunk?

  mode console # switchport general

  Console # switchport General allowed vlan add 300-320 tag

  Console # pvid General switchport 301

  Console # end

  Are we sure that the VLAN 301 IP address is 10.49.56.0? This doesn't seem fair.

  When we try to pings on the trunk/General connection to the Cisco switch, make sure you that the servers have the default gateway defined on the VLAN IP address they are in access mode. Thus, when in the access mode VLAN 301 the gateway server would need to be 10.49.56.0. I would like to verify that the IP address, however.

• How to connect W XP to DSL with Dual Boot Windows 7 Pro & Windows XP Pro,

  Have Windows 7 Pro & Windows XP Pro installed in a dual-boot on a new computer configuration. Have Windows 7 Pro connected to the DSL through a wired connection to the Cisco router. How can I connect Windows XP to DSL, via wired or wireless?

  Hello

  Thanks for posting your query in Microsoft Community.

   

  I understand that you must also connect the Windows XP operating system to a network.

  Here are a few steps to do this, please follow.

  Step 1: Set up Windows XP DSL Connection: using the new network connection wizard.

  1. Click Start and follow the path: programs-> Accessories-> Communications.

  2. Select the New Connection Wizard , and then click Next.

  3. There are several options in the wizard. You set a Windows XP DSL connection, select the option above that says to connect to the internet and click Next.

  4. Select Setup my connection manually and click Next.

  5. Here, there are three options. The first is for the modem connection, so we must not select. If your DSL account is always enabled, select the third option and click Finish and see the next section on IP addresses. If your DSL account is a limited account, which requires the password, select the second option and click Next.

  6. Enter a name for this connection, and then click Next.

  7. In this screen, enter your DSL ID and the password that you got from the ISP. Click Finish.

  Hope this information is useful. Please update the status of this issue. Do not hesitate to contact us to get help with the Windows operating system. We are happy to help you.

  Thank you.

• The 300 series switches are compatible with detection of PoE before standard in old phones Cisco?

  The 300 series switches are compatible with detection of PoE before standard in old phones Cisco? They don't seem to be (7902G don't turn on when it is connected to a SF302-08MP with firmware version 1.1). What no need special configuration on the switch to enable this detection?

  Please note that the switches of the series 200 and 300 are now supported POE Legacy Cisco from September 2011, to provide power to 7960, 7940 and other phones standard pre and APs. Details on the following link:

  https://supportforums.Cisco.com/docs/doc-18337

• With Cisco Secure ACS for Windows GANYMEDE +, authentication fails with AD

  I'll put up a Cisco Secure ACS 4.2 server to act as a RADIUS server for switches and routers I use Windows 2003 server for the candidate countries.
  and an Active Directory of Windows 2003 server.  The ad server is very good, it is used for many other things.

  I've implemented ACS as defined nit it installation guide, including all the steps in the "Member Server" section of the installation guide
  When you use AD as an external database (e.g. setting up services to run with a domain administrator account, set up a machine called "CISCO"
  on the field, etc.).

  I've set the unknown user policy to use the database of Windows, if the internal database does not contain the details of the user.

  If I add a user to the internal database, authentication goes through fine, with an entry in the journal "Authentication," spent

  02-24-2010, 05:07:03, authentic failed, eXXXX, Network Administrators (NDG), X.X.X.X, (default), internal error, (get the internal error error message)

  I scoured google etc and just cannot come up with any reason why this should be the case.
  I followed all of the installation to the letter guides.  I need to get this up and running as soon as possible,
  so am eager to know if someone can help me with this one!

  Thanks and greetings

  Sharan

  George,

  Internal error is fairly generic, but a common situation, we see this error is when ACS is installed on a

  64-bit computer.  ACS would not work with the active Manager when it is installed on the 64-bit before machines

  ACS 4.2.1.

  -Jesse

• Why has my connection AirPort Extreme recently stopped with my Tablet Android and Windows 7 laptop, but connects very well with all Apple devices?

  Why has my connection AirPort Extreme recently stopped with my Tablet Android and Windows 7 laptop, but connects very well with all Apple devices?

  What exact model of AirPort Extreme do you have? Either have your tablet or laptop Win7 been updated recently? They were both able to connect before and not now OR they were never able to connect? Can the laptop Win7 access Internet when connected by Ethernet? One of these devices have problems connecting to other networks Wi - Fi?

• Hello everyone, I just bought a Thunderbolt Apple display to use with my 2012 15 "27" Macbook Pro, Win10/Bootcamp. Is anyone know the procedure to get the display to work with Bootcamp Windows 10?  I have connected screen but no picture. TY

  Hi all

  I just bought a Thunderbolt Apple display to use with my 2012 15 "27" Macbook Pro Win10/Boot Camp running. Is anyone know the procedure to get the display to work with Bootcamp/Windows 10? Is there a setting in the training Camp that must be turned on to make it work? I have connected screen but could not get a desktop display.  Any help would be really appreciated! TY

  The monitor should have a TB and adapter power connector. The monitor works on both OSX. ? If so, shut down of windows, connect monitor and start Windows. Your TB 2012 monitor is not plug-and-play with Windows.

  Please see ports Thunderbolt and views: frequently asked questions (FAQ) - Apple Support .

  1. the "hot pluggable" Thunderbolt devices using Windows with Boot Camp?

  Thunderbolt hot plugging is supported under Windows 8 or 8.1 on all Macs from 2014 and later.

  For all other Mac computers, Windows 7, 8 and 8.1 scans and active them Thunderbolt devices connected to ports Thunderbolt during the Windows startup process. If your device has been plugged in not at startup, Windows detects not without a reboot.

• I can't connect my computer at home it has windows xp professional on... just go round in a circle with 30 seconds of countdown to try to open a session.

  I can't connect my computer at home it has windows xp professional on... just go round in a circle with 30 seconds of countdown to try to log on... I tried options menu that is to say; go to the last known working etc etc... but not good. Problem came when the wife has removed some material... not been able to get a blue screen connect etc. Since HELP!

  original title: help!

  If you have no Windows CD, you can not do a repair installation.

  If you have no Windows CD, the message from the moderator of the Forum Nicholas_W will not help you either.

  If the disk verification fails, there is no sense to try a repair installation because the file system was obviously some problems that must be fixed first (at least that is what I think).

  Wouldn't you want some ideas that actually work?

  The error:

  STOP: 0 X 00000024 0 X 00190203 0X82F42108, 0XC0000102, 0X00000000

  indicates a problem with your NTFS file system.  You can usually solve this by running chkdsk/r from the XP Recovery Console.

  The question was preceded by a loss of power, aborted reboot or abnormal termination? (This includes the plug pulling, buttons power and removing the battery).

  These can cause corruption in the file system that must be fixed before you do anything else.

  If none of these events occurred (or even if they have not taken place), you must verify the integrity of your file system before anything else (especially "try" things).

  Here's how:

  Boot into the Recovery Console Windows using an XP bootable installation CD.

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.