Crashes when I plug in the AC/DC adapter

Similar Questions

• The computer crashes when I plug in the ethernet cord

  I'm having a problem with my laptop. It will start and run fine without the ethernet cord. As soon as I plug it to the computer, a window appears and tells me that Windows has experienced a critical error and stops. If I unplug the power cord, it works very well after the restart. Please help me I am not getting any other error codes or messages, so I don't know where to turn. I ran malicious code detection and McCaffe and no solution to my problem.

  Hello

  When you plug it in, the network card to become 'in service', the software support and drivers and the loading error occurs. This probably indicates a problem with the network card drivers. Download a new game from the manufacturer of the laptop and install to see if refreshing their help.

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• When I plug in the USB on my netbook and you want to open, it tells me that there is no disc in the drive?

  Original title: BAD USB

  I have an Acer netbook. I was able to download my photos from my computer on a USB key until a few days ago. When I plug in the USB on my netbook and you want to open, it tells me that there is no disc in the drive?  Why does it say this?

  I am confused with this... I really hope someone can help me.

  Thank you for your time in doing

  Dido

  Hey Toni-LeeFurlotte,

  ·         Have you tried to connect to a different USB port?

  Method 1: Try to connect the USB key to a different port on the netbook and check the issue. You can also connect the drive to another computer and see if the problem persists.

  Method 2: Update of the netbook with the latest chipset drivers. In addition, install other updates of the device driver. Log in the Web site of the manufacturer to do the same thing.

  Method 3: This problem can also occur if there is a drive letter conflict. A drive letter conflict occurs if the disk that is affected by the error is mapped to a reserved drive letter. I suggest you try to change the drive letter.

  How to change drive letter assignments in Windows XP

• HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  The battery is dead. When I try to turn on the laptop by plugging the AC adapter does not charge or led power LED does not turn on. But when I press the power button, the power, the indicator flashes and turns off (when power adapter connected).

  (1) I tried the press and holding the power button for 30 seconds after removing the battery & AC adapter / CC.

  (2) I tried to change the power adapter too.

  The problem is that it is.

  Your advice is very much appreciated.

  Thank you best regards &,.

  Zia

  Dear customer,

  Welcome and thanks for posting your question on the Forum of Support HP

  It seems that you are not able to turn on the laptop and tried to solve the problem

  Please perform steps listed to find out if it is a hardware or software problem below:

  1. remove all cables and devices, disconnect them and try to turn on the device

  2. check the LED light situation and ensure the action of the spring button / stop is normal

  3 Exchange with a well known power cord and the AC adapter

  4 Pack no adapters are available, check if the power adaptor is slightly warm

  Note: This will give us an indication that the power adapter could be good

  5. do you know if the laptop was in battery or power adapter when you used the last time

  Note: Make sure that there is no spill of liquid or cutting

  6. check if the Port of the AC adaptor is loose/broken

  Note: If the laptop is not on even with a power adapter well known, this confirms the hardware failure with the system board or power DC Circuit

  Hope this helps for other queries to answer the post and feel free to join us again

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  I work on behalf of HP

• HELMET No. Smartphones blackBerry icon when I plug in the BB Bold 9900 helmet. Help, please!

  Hello

  I just got my new BB bold 9900. Has updated the OS to v7.1.714. Now I see not a helmet on the homescreen icon when I plug the headphones of BB. Although I get sound when I plug from the 3.5 mm plug.

  Another issue is when I receive a call I am not able to hear the call, ringing on the headset, rather that I hear from the speaker as I would when no headset is plugged.

  I heard that it is a common problem when an upgrade of the OS is made. Is there a solution? Help, please!

  Hello crazygamerg7,

  Welcome to the BlackBerry support community.

  Thank you for your question about the helmet on the BlackBerry 7.1 software feature.

  The headphones icon should only appear in within the phone application and not on the home screen when connected and on a call.

  The ringtone will also go through the speakers of the device and not on taking 3.5 mm connected headphones. This is normal.

• Illustrator crashes when saving files in the default directory not in Mac OS 10.10 or OS 10.11. What is the solution?

  Illustrator crashes when saving files in the default directory not in Mac OS 10.10 or OS 10.11. What is the solution?

  There is no solution.

  If that is your only question, you should be happy.

  El Capitan Yosemite and CS5 are not compatible. For some people it can run more or less, for others not so much.

• InDesign crashes when I click on the file tab

  InDesign crashes when I click on the file tab. I can open and save files by using shortcuts, but it is not possible to create a PDF or a package. So, I have to use the file tab. And then, InDesign stops, I need to force it to stop. I've already deleted InDesign from my computer and reinstalled, but I had the same problem. Can someone help me?

  Try to set the number of recent files to display 0

• iPad 2 Mini - Lcd shows the Apple logo for 2 seconds and disappears but reloading works when I plug in the charger.

  The title should cover everything about what I'm going to tell you.

  The screen is black, while the iPad is running when I plug it into my mac, I see all my data and I can hear the sound of my messages/screenshot or screen when charging.

  The only time I see the Apple logo for 2 sec is when I restart the iPad now Power + Home at the same time.

  Would appreciate if you guys could help.

  NVM, I found the cause of this. This is a backlight problem. Apparently the filter or the fuse has been damaged and needs to be replaced... another $ 40 on the iPad repair...

• WiFi connectivity weird when I plug in the USB Flash drive?

  I found this WiFi connection problem a few days ago, when I plugged a USB Flash drive in "USB port right side' of my MacBook Pro.

  Every time when USB , WiFi won't work - the connection is lost and can not connect to any hotspot even turn the WiFi market.

  I found more weird, ONLY this brand and model key USB could be the abnormal Mac WiFi.

  

  This problem will not happen to another USB port even I put the Flash drive in the left side, USB port, weird isn't?

  Conclusion, this flash drive cannot be used with USB port on the RIGHT side, another USB port works fine. If WiFi don't work.

  All other USB devices I've owned are working very well on the USB ports on the right or left side.

  Could Apple support or any helps me to understand why this happen?

  PS. I had the Apple's Diagnostics and received a message "no problem found".

  PS #2. Right - same USB port side and next to the HDMI port on MacBook Pro 13 "model 2015" (snack for someone who confuse average left or right)

• MS A30 - battery charging when I plug in the power cable

  Hello

  I'm having some problems with (I think) on my A30 power management utility. When I am running on battery power and I plug in the power cable, the battery continues to discharge even if the laptop 'knows' that it runs on the power grid (ie the utility says "current generator: alternating current.") "Online, discharges: 82%. Strangely, if I put the laptop in mode 'sleep', then resume, she goes back to normal (i.e. working on current alternative, the battery charges).

  It is true, I think that this began after I installed "PC Pitstop optimize Scan" www.pcpitstop.com (please, not conferences - I used a couple of their public services before and they were very good, so I thought it would be too much), so I guess it's some sort of configuration problem, but I have no idea where to go from here. I went through all the options on the power management utility, but they all look sensitive. Any ideas (other than do not install software stupid, doubtful)?

  Kenny

  Hi Kenny,

  I experienced this behavior on my A30 where the system says it works on current alternative, but still drains the battery and stops eventually.

  In my case the problem has proved to be a loose DC Jack that sometimes cuts off contact with the socket on the back of the laptop. This momentary loss of power DC seems to provoke the power management utility switch to battery power, even though the DC power is restored. The only way out of this situation is to Hibernate / restarting the laptop.

  I think that it is a problem with the power supply subsystem in the laptop that does not react properly when it encounters a momentary loss of DC. Then the Toshiba power management utility is no longer responds correctly and switches to the battery power.

  My only solution to this was to anchor the DC cable to the back of my A30 so that there is now no chance of the plug DC moving in its socket. This has proved to be very effective for my A30 and I've had no recurrence of the problem.

  HTH

• Contacts crashes when you write in the company field

  In recent weeks, whenever I have add a new contact, or modify an existing one, contact crashes when I try to write something in the area of the company. When I paste something in this area that I had already written elsewhere, it does not crash...

  Please launch the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Step 1

  For this step, the title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  In the upper right corner of the Console window, there is a search box to filter. Enter the name of the application crashed or process. For example, if Safari has crashed, you would enter "Safari" (without the quotes).

  Each message in the journal begins with the date and time when it was entered. Select the messages since the time of the last fall, as appropriate. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name, may appear in the log. Anonymize before posting.

  Step 2

  In the Console window, clear the search box, and then select

  DIAGNOSIS AND diagnostic USE information reports ▹ user

  (not diagnose them and use Messages) in the list of logs on the left. There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points downwards. You will see a list of reports of incidents. The name of each report begins with the name of the process and ends with ".crash". Select the most recent report on the process in question. The content of the report is displayed at right. Allows you to copy and paste to validate all of the content, text, not a screenshot.

  I know that the report is long, perhaps several hundred lines. Please report all this anyway. If the report is only a few lines, make sure that you have disabled the search box.

  If you don't see any report, but you know, he had an accident, you have chosen diagnostic and using the list of Log Messages. INFORMATION on the USE of DIAGNOSTIC AND choose instead.

  In the interest of privacy, I suggest that, before posting, you change the UUID ' anonymous, ' a long string of letters, numbers and dashes in the header of the report, if it is present (it cannot be). "

  Please do not post other types of diagnostic report - they are very long and rarely useful.

  When you post the journal excerpt or the accident report, you might see an error message on the web page: "you have included content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• Turn off the music when I plug into the speaker / earphone cord

  Turn off the music when I plug speake / headphones cord. Have to unplug to get the music to play again.

  Have you ever force reboot the phone by holding down the button sleep and home for 10 seconds, until the Apple logo comes back again? You won't lose data, but it can cure a few glitches.

  Usually the music stops if you unplug the headphones to the device, and you have to press 'play' again to keep listening via the external speaker.

  If you use the external speaker and plug in the headphones, the song doesn't stop and continues to play through headphones. Just tried it with my camera.

• PC does not recognize the ipod when I plug in the USB cord.

  I have an ipod touch, and it will replace my old ipod.  When I plug the USB cord, nothing is recognized by the computer.  It is also not recognize my old ipod when I plug it now.  I have other devices that use a USB cord, and they work as they should.

  Apple told me to check with Security Essentials to see if they are blocking a pilot... I am quite at a loss.  It's the ipod or it is safety, or is it the computer?

  I tried everything on separate computers, and they don't always work.

  Any help is appreciated!

  It is not MSE-you get a warning if it were.  Try another cable or try on another PC.  It sounds like the cable might be the problem if all of a sudden or iPod works.

• Passport Mass Storage Device does not appear to the top, when I plugged in the USB Port on Windows XP

  I have connected my passport mass storage device to a USB port and it notifies as new hardware, but it did not show in my computer anywhere. However, I installed and uninstalled several times my computer.

  Hello

  1. what happens when you plug the device to your computer, you get an error message?

  2. don't you make changes to the computer until the problem occurred?

  I suggest you try the steps mentioned below and check if it helps.

  Method 1:

   Try to connect the Passport mass storage device into the other USB port or try to connect the Passport mass storage device in another computer and verify that the problem persists.

  Method 2: Try running the Fixit tool from the link below.

  Hardware devices do not work or are not detected in Windows:
  http://support.Microsoft.com/GP/hardware_device_problems

  Method 3: Also try to follow the steps from the link below.

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive: http://support.microsoft.com/kb/925196

  Hope this information is useful.

• WMP 11 crashes when right click on the application

  WMP 11 crashes when I right click any where on the screen of the application or you are trying to click on tools or view, among many other things. I'm trying to get the list pane to see the and if I click on playing, and the drop nothing appears. usually crashes right after that as well. Please help, I can't find anything about it!

  so, I thought about it! for anyone else who has this problem - I hope that this saving you countless hours of frustration, I've experienced...

  -J' restored wmp version 9

  -J' completely deleted all system files and applications to version 11

  -J' rebooted my computer and reinstalled version 11

  -for some reason, it works! :)

  This may seem very simple, but I've tried so many different configurations and random ideas that I'm frankly surprised, it worked! Hope this helps someone else.