Creating image using disk utility

Similar Questions

• Make the disk image using disk utility and the message "Apple_HFS: 0" is displayed

  I'm doing a disk image to try to work on that later. This is an image of a failed disk drive. Some areas can only be read, I know and the process takes a long time because of this, so I'm willing to be patient.

  I get messages in the disk utility window that says "Apple_HFS: 0" and "Creation of image xxxx.dmg.

  The disc has about 700 GB. I started it about 20 hours ago, and the blue bar is about 5% of the way, so not much happened.

  I fear that the message "Apple_HFS: 0" means that the disk image is not made. I am concerned about the part "0". I don't know what that means.

  I don't want to do it for days and days and find that there not to make a disc image all this time.

  I realize that the fact that the external drive is damaged (probably damage) means that this process will take longer than normal. I am willing to leave it for a week so that he can make a disk image. But not more than a week because then it is not worth my time.

  So my question is: does the message ' Apple_HFS: 0 "means something bad, or that the message normally during this procedure?

  Apart from this message and the message "Xxxx.dmg imaging", there is no other message.

  I think I'm making progress because the bar has moved since I started the process. For a long time I couldn't see a bar at all. And today, after spending the night, there is a small bar, as I said, about 5% complete. But it's very slow. It would take at least a week for the disk image to be made. I just want to know if the messages that I see are normal or not.

• Content transfer to the old drive again using disk utility?

  I just bought a new SSD and want to transfer all my HD content in a Mac Mini to it.

  The SSD vendor has advised using disk utility for drag-and - drop the old drive to the new, but until now I

  wasted summer. I formatted the new drive and resized the partition on the old drive to

  It is smaller than the new. When I try to run the utility, it seems to initialize and start the transfer, with

  at 2 p.m., provided the time to complete the process. However when I get back later nothing seems

  have been carried out.

  Anyone have any suggestions?

  No drag & drop won't do. Do this instead...

  12.x disk utility: create a disk image

  Also, you could use Time Machine, or software of cloning asSuperDuper! or Double Cloner

• Use disk utility to erase hard drive, erase everything, it

  I just use disk utility to erase the hard drive of Windows base.  It has 6,2 GB of space.  The erase process takes only a few seconds.

  I read that it could take hours.  I suspect that he does not erase the hard drive.    I have several old PC drives and want to use disk utility to erase.

  How would I know if it works?

  Rolland

  I would just use disk utility to put those (journaled) in Mac

  If nothing has been left in the delete process - the format will take care of it

• After you download El Capitan, I received the following error message when you try to install: the drive is not formatted in MAC OS extended (journaled). Use disk utility to enable logging or reformat the disc. Can anyone help?

  After you download El Capitan, I received the following error message when you try to install: the drive is not formatted in MAC OS extended (journaled). Use disk utility to enable logging or reformat the disc. Can anyone help? (My disk utility shows that she in MAC OS extended (journaled) format.)

  It shows that it is Mac OS extended, not journaled. Click enable logging in the toolbar.

  The thing you read is if you format the drive using the RAID settings you have selected. You have to look at the bottom of the window where it shows the Format.

• Cannot use disk utility to create the partition of the free space on the external USB drive.

  I have a red 3 TB Western Digital drive in a USB hard drive docking station.

  The reader is GPT, and I have two volumes on it (a single volume is "Microsoft reserved", another volume is NTFS).

  The other part of my drive is 1.5 TB of free space. I want to create a new partition with free space so that I can put backups Time Machine encrypted external hard disk.

  I checked free space on the drive with my Windows machine:

  
  DISKPART> list disk
  
  Disk ### Status Size Free Dyn Gpt
  
  -------- ------------- ------- ------- --- --- 
  
  Disk 0 Online 167 GB 20 GB
  
  Disk 1 Online 465 GB 0 B *
  
  Disk 2 Online 2794 GB 1526 GB *
  
  DISKPART> select disk 2
  
  Disk 2 is now the selected disk.
  
  DISKPART> list part
  
  Partition ### Type Size Offset
  
  ------------- ---------------- ------- -------
  
  Partition 1 Reserved 128 MB 17 KB
  
  Partition 2 Primary 1267 GB 129 MB 
  
  DISKPART>
  

  DiskPart displays 2 partitions - a 128 MB and the other GB 1267 with 1526 MB of free space.

  I took the hard drive of my MacBook Pro running OS X El Capitan 10.11.3 and pulled towards the high disk utility, but for some reason, that it does not resemble the disk utility it is to see the free space, so I can't create a new volume.

  Here are a few screenshots:

  ... of the physical disk in disk utility (notice how it doesn't seem be all unallocated space on the disk to create a new volume):

  

  ... of the NTFS volume in disk utility:

  

  ... of information for the drive in disk utility:

  

  ... of information for the NTFS volume in disk utility:

  

  ... of the partitioning settings page. Notice how the sign is grayed out (I can't create another partition):

  

  

  I'm a new Mac user. My company recently gave me a Mac, so the first thing I want to do is to create a new partition on this external USB drive to put backups Time Machine figures on it.

  In the research I did find a way to do it on a mac computer without erasing the drive and starting over. But you can go to your windows computer and partition the free space of disks. Then use the mac to set the free space as mac os extended journaled. Here's what I found. http://www.PCWorld.com/article/2066191/how-to-partition-a-hard-drive.html the only other way would be to copy the file on the external drive, somewhere, so you can delete it and re partition for windows and mac. Then reinstall windows files. I'm not familiar with windows systems.

• Yet cs4 creates image invalid disk (iso file)

  I have a video I change in first cs4, exported a .mpg file I import into encore to create a DVD. This works for the most part very well (I have to delete the .xmp file * before you import it into encore).

  Today, I edited the video, re-encoded the mpg file using quality 5 and 2 pass vbr and added a slideshow (6 photos) to the project yet. It relies as well on a disk (iso file) image. But when I try to burn the iso file using windows 7, he said that the iso image is not valid. I tried imgburn and got an error like this:

  session 1 track 1 MODE1... 2054

  DVD format: mode 1... 2048

  If I ask for imgburn to continue he then said something about CSS and encryption, which I do not, then I guess that the iso file is too messed up.

  I burned a DVD5 directly since again, and it works in a dvd player.

  No idea why this iso invalid occurs and if there is a workaround?

  Since cs4 is not the latest version, I suppose there is no hope to fix a bug?

  avpromedia, as a test, I would create a new project and try a simple test project, or the project there. I don't have a problem with the process you describe and suspect that this project is corrupted.

• I can clone a drive using Disk Utility Version 15.0

  I want to replace my MBP 5.3 HDD with a larger SSD. I would like to clone, make sure that his startup, then install. Utility of disc is not clear and I don't want to spoil. Any help is greatly appreciated.

  Thank you

  I want to replace my MBP 5.3 HDD with a larger SSD. I would like to clone, make sure that his startup, then install. Utility of disc is not clear and I don't want to spoil.

  I recently tried restore DiskUtility to clone a drive and it did nothing.

  You can easily download a free trial of Carbon Copy Cloner to create a bootclone which the recovery partition and all.

  https://Bombich.com/

  MacBook Pro (15-inch mid-2012), OS X El Capitan (10.11.5), i7 480 GB SSD 16 GB RAM iPhone5 iOS9.3.2, Parallels10.0.2, HP OfficeJet Pro 8620

• Cannot start Bootcamp, after you have added the partition using disk utility

  My question is similar with repair Boot Camp after having created the new partition.

  recently I install the el capitan + windows 7 (using bootcamp), everything works fine after I add the third partition. (I anticipate the third partition will be use for dropbox, for mac and windows can sync-ing a dropbox for each folder).

  After I've done the third partition and restart the system, I want OPTION and found no windows.

  My mbp spec:

  MD101 2012 13 ",

  SAMSUNG 850 PRO SSD 256GO,.

  16 GB RAM,

  elcapitan OS x + windows 7 ultimate.

  Thank you

  Can you post the output of the following commands in OSX Terminal?

  diskutil list

  Cs diskutil list

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

  The "sudo" commands will prompt to enter your password, and there do not appear to come back. You can also see caution against improper use 'sudo' and the potential loss of data due to an "abuse" of the order.

• Cannot create images using the Digital Image Standard 2006 Editor

  original title: Digital Image Standard 2006 Editor

  I have the Digital Image Standard 2006 Editor on my Windows 7 computer and for some reason, the only thing I can't do with it is to create frames and mats. Nothing happens when I click on this option. Everything else works so I am confused. Any suggestions?

  Hi Kittea,

  Thanks for posting in the Microsoft Communities. The problem description, I understand that you are not able to access some options in editor of Digital Image Standard 2006 application. Before you start the troubleshooting steps, provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         You get the error message? If Yes, what is the full error message?

  Follow these methods.

  
  

  Method 1: Uninstalland reinstall the program.

  
  

  Method 2: place the computer in a clean boot State to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  
  

  Note: After completing the steps in the clean boot troubleshooting, follow step 7 the link to start the computer to a Normal startupmode.

  I hope this helps. Let us know if you need more assistance.

  Thank you.

• Burn a DVD with "disk utility".

  Before El Capitan (10.11.2), I was able to burn a DVD using "disk utility".  Here are the instructions that I used.  Disk utility has now a new version Version 15.0 (1511.3) and the statement no longer work.  Can anyone update these instructions?

  Copy DVD

  Follow these instructions to make a copy of your DVD unprotected:

  Insert your DVD into your Mac. Most Macs will automatically launch the DVD player. Once he starts, he gave up. You should see your DVD drive mounted on your desktop.

  Open disk utility (Applications > utilities). Select the DVD drive in the list on the left. You will notice that there are two DVD icons - select the one slightly indented (this is the DVD itself, while the first is the drive).

  Click on "New Image" in the main window of disk utility.

  Choose a name and a destination in the window "Save as...". ». Don't forget that your destination should have enough space to copy the whole DVD, which can be more than four concerts.

  In the window "Save as...". ', to ensure that the selection 'Format of Image' is set to ' CD/DVD Master' and the selection of "Encryption" is set to 'none '. Click Save.

  After you have copied the DVD in your destination drive, return to disk utility. Your new disk Image will appear in the list on the left side of the disk utility window. The original disc of DVD on your Mac.

  Insert a DVD disc that is accessible by writing in your Mac. Select your disk Image created in the list on the left side of the disk utility window. Click on "Burn" in the main window of disk utility. Choose your burn speed and if you want to check the data burned.

  You will receive confirmation once you the DVD are engraved with success and you are all set with a new copy of your DVD drive. Just save your new disk Image and you can make a copy whenever you may need.

  That is right. Apple has removed this feature FROM.

  You can do it from the Finder

  http://osxdaily.com/2015/11/22/burn-disc-images-OS-x-Finder/

• Love at first sight and disk utility

  Hello

  With the old version of disk utility, I could start in the repair using the command + R section, click disk utility, and then copy my computer perfect HD over to another Mac connected via Thunderbolt and in target disk mode. This process took about 7 minutes. Is it possible to do it again? Use the migration wizard is not a viable option because it takes over 30 minutes to copy it to the users and applications and I have several computer at image Labs.

  You try to restore your hard drive to another on a target machine?     If so, you can always do this.   Reboot from Recovery HD and use disk utility.  To 1 restore another disc, you select 1st target drive.  Then on the Edit menu, select Restore.  Then in the drop-down list, select the source drive.  If you love at first sight, this should go pretty fast.

• I have little problem with my disk utility.

  Hello Sir/Madam...

  I have a little problem that I can't fix it.... so please can someone help me with this question, I can only explain with this image as an attachment, I thank those still and wish everyone the best chance.

  

  Make a backup, best 2 separated on 2 discs. Start of recovery volume (command - R on a restart, or hold down the option/Alt during a restart and select the Volume of recovery). Run the check/repair disk utility and repair permissions until you get no error.  If this doesn't resolve the problem, try reformatting the drive using Disk Utility/Erase Mac OS extended (journaled), then click on the Option button and select GUID. Then re-install the operating system.

  OS X recovery

  OS X recovery (2)

• Cloning of SSD HD via active with Filevault disk utility

  Hi all

  I want to improve my HD to SSD.

  I intend on using disk utility for recovery mode to clone my HD to a Virgin SSD I bought.

  I must, however, Filevault enabled on my HD.

  It will be a problem when it comes to cloning the drive?

  Thank you

  Adam

  No, it shouldn't be a problem. It may be necessary first turn on FileVault and encrypt the SSD. But if there is no problem just turn off FileVault on the HARD drive.

• Disk utility doesn't work do not at all

  The problem started with my iMac (10.11.6) slows down. I rebooted, it worked fine for a while, and then the problem comes back. I tried three times to use disk utility, but every time it's the same thing: the start box appears on the screen, i. by "tap" first aid, then... nothing. Nothing at all. I then tried to force out the utility disk, but for some reason any Force Quit option suddenly didn't work. Everything I had was the ball Beach and the non-functioning du box. So what's happening? Virus (I have Trend Micro, but nothing is perfect)? The age?

  Uninstall Trend Micro anti-virus software. It is not necessary on a Mac and is probably causing the problems you describe with disk utility.

  Third party software anti-virus is not necessary on a Mac and cannot cause problems.

  Help here > https://esupport.trendmicro.com/en-us/home/pages/technical-support/1061005.aspx

  On the Protection of the integrity of the system on your Mac - Apple Support