CSCuy98373 - Dead State SRI WAAS C4331 SN when running traffic with 3.16.02 XE

Similar Questions

• MAX not to kill engine when running active with analog feedback

  I just changed my engine to use analog feedback instead of encoder feedback, but now he does not kill the engine when the switch is activated. I use a PXI7358 with a servo, and a PXI6363 and PXI6221 motor. The PXI6221 reads raw gauges of a force sensor measures 6 axes, mounted on the endpoint of my linear actuator (powered by the servo motor). LabVIEW makes a calculation on the tensions of strain gauges and exits through the PXI6363 a single voltage that is proportional to the force in one of the axes. I feed the analog voltage at the entrance to axis 1 on my analog PXI7358.

  Previously, I had used an encoder for comments and whenever I came at the end of race before or back the engine would immediately cease. Now that I'm using analog feedback, the sails of the actuator throughout the limit switch and doesn't stop, even though I see the LED light up in MAX, which indicates that the limit switch is active.

  In a LabVIEW VI I can kill the engine when the limit switch becomes active, but I would like for it to transcend LabVIEW and arrive at the MAX instead. Sometimes, apparently, there is a slightly different zero voltage output by the 6363 and the actuator moves very slowly in a sense and if I'm not looking for it runs the risk of crashing on the stop, because it is not honor the status of the limit switch.

  Any suggestions? Thank you.

  Matthew,

  what you see is the expected behavior. The good news is, you can change it, but let me explain first of all, what is happening here:

  When an axis hits a limit switch, the default operation is to put an end to the axis. This means that the current value of the feedback becomes the current set point. With feedback from encoder translates a full stop of the axis, which is typically the desired behavior. With analog feedback (g. e. force) this means that the axis is trying to keep the current value of the force, which does not necessarily mean, that the axis stops.

  The solution is to stop the axis with a kill command, which sets the DAC to zero and says the line out to disable to turn off the player. You can configure the axis to stop with a kill command whenever a limit switch is activated by using "Set u32.flx" (switch Stop Type = attribute, value = 2).

  I hope this helps.

  Jochen Klier

  National Instruments

• Cannot get his work when running applications with "Run as Administrator" all of a sudden.

  My daughter has been using my computer and done 'something' to him. To get the sound to work now under IE, Firefox, Ventrilo, etc etc I have to run applications as an administrator... even if my account has administrator privileges.  I'm at my wits end, because I've tried everything, and Google returns nothing to give me a helping hand.

  I am running Windows XP Pro SP 3

  I don't know that if Skyke was working or not, I removed it when I started to try to fix things. No program used his work properly, browsers, windows live messanger, ventrilo, etc..

  I tried both FixIt programs you listed above, found nothing.

  In the end, I gave up and reinstalled.

• Download a file using a php script when running applications with LCD screens

  Hello! I'm developing an application in Flex 2 / Java - running on the LCD / JRun server.
  
  I'm trying to add downloading features. I use a script php to the download section.
  
  First, I'm just trying to put the script in the application directory. Does not work.
  After that I created an apache server where I put a small web site with my script. He tells me that my file is downloaded correctly, but I can't find the file. The apache log I don't give no errors.
  
  Can someone help me?

  Originally, I had problems w / the file placed in C:/whatever.ext b/c I was not using relative paths.

  This is the code I use:
  --------------------------------

  $MAXIMUM_FILESIZE = 1024 * 1024 * 2; 2 MB
  $newFileLoc = '. '. "/ wherever/file.jpg.

  If ($_FILES ['Filedata'] ['size'])<= $maximum_filesize)="">

  move_uploaded_file ($_FILES ['Filedata'] ['tmp_name'], ".") / temporary / ". $_FILES ['Filedata'] ['name']);"

  Rename ("./temporary/". $_FILES ['Filedata'] ['name'], $newFileLoc);
  chmod ($newFileLoc, 0777);

  }

  ---------------------------

  Editing of this article by Adobe:

  http://livedocs.Adobe.com/flex/201/html/wwhelp/wwhimpl/common/html/wwhelp.htm?context=live Docs_Book_Parts & file = 17_Networking_and_communications_173_6.html

• SRI-WAAS, Manager of plant by the name of "No.-HOSTNAME".

  Hello!

  Im trying to record 4 ISR-WAAS to a manager of the plant, but every time I run the installation procedure, the first SRI-WAAS record well, but with the host name NON-HOSTNAME; and the next SRI WAAS also. For this reason, I got an error message that there is another device with this hostname and I can't change it! ...

  Already try the command hostname inside the console of the SRI-WAAS, but does not work... I also tried to change the host name in the Central Manager, but I can't find the way.

  Any advice?

  Thanks in advance.

  captura_de_pantalla_de_2016-08-28_17-57 - 59.png

  

  Hello

  Looks like you're having Bug CSCuu23859.

  The SRI-WAAS release notes say that this problem has been fixed in the software v5.5.5 (according to the screenshot you run v5.5.1)

  BugSearch CSCuu23859

  SRI-WAAS release notes

  Best regards

  Andreas

• SRI-WAAS with two routers

  Hello!

  Is it possible to have two routers (including one with RSR-WAAS and the other without) on a remote site router without ISR-WAAS to use the ISR-WAAS of the other router? (I have only finddual router with dual WAAS SRI in the CVD).

  Concerning

  Michael

  Hi Michael,

  Yes it is possible.

  However, the Redirect method depends on what type of router without ISR-WAAS is:

  another report of research international-4000:

  You can use AppNav (the two routers in the same groups of Application Controller & the SRI-WAAS as the sole member af of the AV/Waas node group).

  almost any other router:

  You can use WCCP on both routers redirecting to the SRI-WAAS.

  Best regards

  Finn

• SRI-WAAS and AppNav

  Hi all

  Situation is the following. I have 2 routers x 4351-AX with the SSD upgrades and memory etc. Let's finish MPLS and other internet DMVPN or similar and both with RSR-WAAS configured.

  Is there an argument to have these set up a stand-alone WAAS devices or should they be in a cluster of AppNav? There are advantages and disadvantages to each method here?

  As Akamai Connect running on just the unit facing internet, does that mean it shouldn't be part of a cluster of AppNav?

  Thanks in advance.

  You should have configured cluster AppNav SRI-WAAS part. You can not have WCCP on the single Appnav SRI-WAAS interception.

  The new WAAS codes may work with Akamai to connect.

  http://www.Cisco.com/c/en/us/solutions/collateral/enterprise-networks/in...

  http://www.Cisco.com/c/en/us/TD/docs/app_ntwk_services/WAAS/WAAS/V551/No...

• The former "cannot change the power state of virtual machine: the process has exited with an error: end of the error message" thing again (Fedora 8/Server 1.08)

  OK, this problem beautifully undescriptive I've seen caused by what seems to be dozens of things happening for me.

  I made the mistake of horrible update my FC8 kernel to the latest one (2.6.26.8 - 57.fc8).  Mind you, that's all that's changed.  It was with a 1.06 server with happiness and perfectly good computers running virtual in use before the upgrade.

  After the new kernel and reboot, I had to rebuild vmmod.  I had to get a fix of any - any later that I used with my previous kernel (116 does not solve the problem of compiling) so I used all-any117d.  Update like a champion.

  Try to turn on a VM and Ihanta!, the above error.

  Nothing else was changed.

  I tried the upgrade to VMware Server 1.08.  Used all-new any117d - update OK.

  Error again.

  I have re-run the compilation, this time to say 'yes' to what the installation script to "adjust the permissions of all virtual machines in xxxlist" or whatnot.

  Error again.

  1. status of /etc/init.d/VMware

  Networking networking on/dev/vmnet0 is running

  Invited only on/dev/vmnet1 network is running

  Network invited only on/dev/vmnet8 is running

  NAT networking on/dev/vmnet8 is running

  Responsible vmmon module

  Loaded module Vmnet

  FWIW, I compile as long as root, but have always run VMware server from my UID nonroot.

  What now?

  I'm in the same boat.  Fedora 8 2.6.26.8 - 57.fc8 #1 SMP

  I have tried uninstalling/reinstalling v1.0.6 thru 1.0.8 with all 116 updates and 117d.   117D compiles with every version of server but when I try to turn on a virtual computer I get this error.

  Cannot change the power state of virtual machine: the process has exited with an error:

  vmxvmdb: name of the Index generated by the configuration file

  POST (no connection): Version mismatch with vmmon module: expected 138.0, obtained 168.0.

  You have a bad version of the module kernel "vmmon.

  Try reinstalling VMware Server.

  POST (no connection): failed to initialize the surveillance apparatus.

  Failed to initialize the virtual machine.

  End of the error message.

  I found several posts other people have this problem but

  they are months with no recent activity and nothing that solved the problem.  I found appeared

  to get a fix, one updated the all an update that corrects the problem for

  2.6.26 performing several nuclei, but the link for the update on TI-psycho appears to be dead.  Here is the link to the discussion

  http://Fedoraforum.org/Forum/showthread.php?t=199026&page=2

  Of course, I would like to know how to solve this problem as well.

  Thank you

• Fix it is centered displays error 0x803C0107 when running diagnose files and folders

  When running microsoft fix Dunière and try to troubleshoot diagnose and repair files and folders, I get a masseage indicating a problem prevented troubleshooting start and the problem is the error 0x803C0107. the first time I ran this it worked well all other options of troubleshooting on the microsoft fix, it works very well. How can I fix this error? System Restore did not work.

  Hello

  The error code means "trust validation of the troubleshooting pack has failed. Can I find out which automated patch you are trying to run when you saw the error?

  Try to check the same in the clean boot state and check. See the article below for instructions on how to start your computer in a clean boot state.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.

  I hope this helps.

• Sound work for system sounds and when I mess with sliding windows mixer

  Literally everything is dead silent including steam, ie8 and my games. With the updated audio drivers and all the sounds on highest

  Hi Michael,

  Thanks for posting your query in Microsoft Community.

  Let me ask you;

  1. Did you change to the computer?
  2. What is steam? What is an application or a program?
  3. How you did update the audio drivers?
  4. What is the brand and model of the computer?

  Let's try the methods below and check.

  Method 1: You can run the troubleshooter from the below mentioned link and check if it can help solve the problem , Open the Audio playback troubleshooting utility

  Method 2: I understand that you tried to update the drivers. However, I try to uninstall and reinstall sound card driver.

  a. Click Start, type Device Manager in the start search box and press ENTER.
  (b) in the Device Manager dialog box, expand of sound, video and game controllers.
  c. find the audio device that was included with the computer.
  d. right click on the device, and then click Properties.
  e. click driver, and then clickUninstall.
  f. make sure the boxremove the driver for this deviceis cleared, and then clickOK.
  g. in the Device Manager dialog box, click the Actionmenu, and then clickfind the hardware changes.

  You receive a message that States that a hardware device is being installed, and then the not installed audio device appears in Device Manager.

  h. close the Device Manager dialog box.

  Method 3: Check if the problem persists in the clean boot state

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  How to perform a clean boot in Windows

  Note: see 'How do I reset the computer to start normally after a boot minimum troubleshooting' to reset the computer starts normally after troubleshooting.

  Method 4: Also, look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better. I hope this helps.

  Measures to check the application event log:

  a. click Start.
  (b) in the search box type eventvwr.msc , and then on enter.
  c. now, click Application in the event viewer (local).
  d. now, looking for event log on the right side of the event viewer window.

  You can read the following article:

  Open event viewer

  What are the information in event logs? (Event Viewer)

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• Bills of the AP - query gives output in the editor, but no data found when run from a workflow

  Hello

  I am working on a custom workflow related to invoices from the AP and I came across this very odd situation where the below query works perfectly well by operating in any PL/SQL as Toad/SQL Developer editor but when run in an Oracle Workflow custom, the query raises an exception NO_DATA_FOUND.

  I set debugging instructions to capture the values of the parameters (lv_invoice_id and lv_hold_id being retrieved workflow attributes) before and after the SELECT statement and noticed that the values of the parameters are set correctly.

  SELECT type

  IN lv_match_type

  DE ap_invoices_all aia , ap_invoice_lines_all Arnaud , ap_holds_all aha

  OÙ ail . invoice_id = lv_invoice_id

  ET line_type_lookup_code = "ITEM"

  ET AIA . invoice_id = garlic . invoice_id

  ET AHA . invoice_id = AIA . invoice_id

  ET AHA . hold_id = lv_hold_id

  ET ROWNUM = 1 ;

  Can anyone suggest what could be wrong with that? Having spent 2 days trying to debug this but without success.

  Any help would be greatly appreciated.

  I added a function of the WorkflowTimeout JOB just before function which becomes the flag Match, and it worked. It appears like the workflow engine is somehow unable to assign values to the query. Putting a WAIT, he probably gave the workflow a second to assign variables with values. Seems very strange, but seems to have solved the problem. Do thorough tests to confirm that it does not break something else. Mike - appreciate all your help with this post until now. You were very prompt in answering my questions. Appreciate it.

• Why Premiere Pro CC 2015 crash when you work with still images?

  I am in the phase of learning with first (edited on Sony Vegas for years) and I'm working on a test/learning the project using a mix of videos and photos of my family trips.

  Working with the video looks very good (although the thumbnails take forever to load for the still and video images and need to refresh every time that I re - open a bin). When I work with stills (jpgs in this case), PP CC 2015 crashes at various points. He fell down on a double click to add to the drafting of a subitem, when deleting a still in the chronology of the sequence, a trip as always on the scenario, when you open the tab effects, etc.

  I haven't done this experiment with video.

  Don't laugh, but I was hoping that my laptop Dell XPS (Core i7 4500U, Intel HD Graphics 4400, 8 GB of RAM) would have enough power to use first (a part of why I subscribed). I'm on Windows 10 and keeping the files I work with on my local hard disk solid state. I tried to solve the problem by updating and also reduce the graphics driver, but I'm not as much of a techie like many of you.

  Here is the log of the events since the last crash:

  Name of the failing application: Adobe first Pro.exe, version: 9.1.0.174, time stamp: 0x564dce25

  The failed module name: igdrcl64.dll, version: 10.18.15.4256, time stamp: 0x55a99b59

  Exception code: 0xc0000005

  Thanks in advance for any help...

  Jeff

  Hi Jeff,

  The photos you are editing are really big? How many RAM GPU you have? I assume you are using GPU acceleration (found in the project settings); If you do software only made you still a fall?

  Thank you

  Colin

  First Pro EQ

• TopLink Grid: Create EntityManager fails when running on WebLogic

  Hello
  I am creating WebService that usus TopLink grid to access data. First of all I created simple stand-alone application with TopLink grid and all work very well. Then, I created WebService based on app created previously.
  When I try to run WebService deployed on WebLogic, I got error:
  "line Class ="Oracle.EclipseLink.Coherence.Integrated.config.GridCacheCustomizer"file =" GridCacheCustomizer.java "="30"method ="Customize. "
  java.lang.NoSuchMethodError org.eclipse.persistence.descriptors.ClassDescriptor.setFullyMergeEntity (Z) V
  It fails in the entityManagerFactory.createEntityManager () method.
  If deleted the eclipse configuration file - link.xml webservice customizer statement works. Maybe for server application needed some additional configuration or initialization?
  
  
  Thank you
  Alex
  
  Published by: user9360947 on March 29, 2012 06:09

  What is the version that you perform the deployment? The method not found was added in a later version, so it is probably there is a version mismatch where the Weblogic instance that is running and the version that you configured when running stand-alone. I think you need probalby use a version of Weblogic as 12.1.1 which comes with TopLink which includes EclipseLink 2.3.2 for this to work, or use a different version of EclipseLink which comes with the Weblogic instance that you are using. Tom described here:
  http://dev.Eclipse.org/mhonarc/lists/EclipseLink-users/msg06874.html

  Best regards
  Chris

• Activity monitor close unexpectedly when running in the background on the left

  Recently upgraded to Mac OS Sierra and Activity Monitor to close unexpectedly when running back plan left (do not smoke and open the activity monitor window) to a blank desktop when you use an application in another office. Clean install I tried but the activity monitor would still be down at random times when left running in the background to another empty office. Someone at - there experience this problem? For most browsing on the web using Safari on another desktop computer when Activity Monitor quit unexpectedly.

  Activity monitor also using a lot of energy since the upgrade?

  Any help would be appreciated. Thank you.

  Model: MacBook Pro (retina, 13 inches, early 2015)

  OS: macOS Sierra: 10.12 (installed via the upgrade, own installed after this problem).

  Do not forget that you are using the activity monitor version which was installed when you upgraded to Sierra. Activity monitor located in the your Mac utilities folder.

  If you have moved a previous version to a different location, it will not work.

  If you are using the correct version, post crash report. Error reports lies in the application of the Console under System reports or reports from usersand end in the suffix .crash. If you choose to do so, omit or hide any information that you consider personal.

• I see two windows 'readers' when I boot with the Option key

  I had to reinstall Windows 10 (with BootCamp).  Now, I see two windows 'readers', when I boot with the Option key button.

  How can I remove a?

  Start two of them in the same installation of Windows?