default in windows updates changes to return

Similar Questions

• Update Windows Installer KB3002885 (and later KB3000061) causes "Failure Configuring Windows Updates, changes of restoration"

  I manually ran Windows Update for about 22 updates including KB3002885 (KB3000061 is not included at this time).  It resulted in "Failure Configuring Windows Updates, changes of recovery".

  Measures taken (without the fix):

  -Reboot

  -Restart in Boot Clean with Services MS no disabled state

  -Updated Troubleshotter

  -System Restore (3 weeks)

  -DISM.exe / Online/Cleanup-image /Restorehealth

  I started installing updates a little at a time and was able to install all the updates about 22 except KB3002885, which always causes the problem 'failure configuration... '. ».

  Updates at this point (November 14, 2014) identified KB3000061.  When update was executed for this update by itself it also caused the problem of the "default configuration... '. ».

  Updates about 22 that have been installed successfully some of them were: KB3000853, KB3004150, KB3003057, KB2978121 and KB2972101.  A more complete list is available if it is useful.

  Windows 8 Pro 64 bit w / Media Center

  Norton Security Suite

  THAT IS TO SAY 10.0.9200.17148

  Worm update: 10.0.22

  Perhaps relevant: I could never update this computer Windows 8.1 in 5 or 6 attempts over a period of 6 months.  Always comes back to the previously installed Windows 8.

  Otherwise, my computer works without other unusual problems.

  Hi Brad,

  Thank you for your response.

  For problems with the upgrade to Windows 8.1, I suggest you refer to the suggestion of Madeni K N replied on 8 January 2014.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows8_1-windows_install/error-0xc1900101-0x40017-when-installing-Windows/8c893ae6-0e9b-4b7d-a647-b9065099efd6?page=1&TM=1389602587060

  For more information, you can check the link below.

  Update to Windows 8.1 of Windows 8.

  http://Windows.Microsoft.com/en-us/Windows-8/update-from-Windows-8-tutorial

  Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.

• Error message "failure configuration windows updates, changes in recovery, do not turn off computer.

  I tried to update my laptop with windows updates and an error message "failure windows updates, changes configuration recovery, stop computer" has been there for 20 hours and nothing happens. I can't get rid of this message despite the closure of the laptop for 2 hours and take out the battery. How can I get out of this perpetual loop please?

  I have windows 8.

  [Original title: Windows updates]

  Use any method is needed to access Advanced Startup Options in Windows 8 or 10 including if necessary to the installation media to create for Windows - 8.1 help Windows to start in console repair on the second screen.

  Startup options run the system restore which is the first line of defense and still has a Restore Point before installing the updates.

  If it does not try to repair the startup or as a last resort a refreshment or a Reset.

• Updates to Windows 8 - "Configuration of the Windows updates, changes in restoration failure"

  Hello

  Recently I finally got my laptop back from repairs after 6 weeks. Now, it is in a 'clean' State (aka factory settins).

  I wanted to get to 8.1 Windows as soon as possible, but for this I need to be on the latest version of Windows 8.

  So I then try to run "Windows Update" and let it install all updates recommended. He manages to download all updates,

  and then he tries to configure these. About 98% or 99%, it gives the following message:

  'Configuration of the Windows updates, changes back failure'

  It then goes in an infinite loop constantly, he ran for hours and hours without having passed this screen.

  So far, the only solution is to reset it to factory settings, which brings me to the point before that I try to update, so it is not move me.

  I've tried so far, but no luck what follows:

  • http://support.Microsoft.com/kb/949358/en-us
  • http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_update/failure-configuring-Windows-updates-reverting/16219e5c-564b-4310-9f68-c9d595bb4cbe?page=1
  • http://support.Microsoft.com/kb/971058

  None of them has worked so far.

  To be clear:

  It is an OEM license. This doesn't mean no DISC, nor any ISO/Exe could work that they do not accept the product key.

  Many other people have the same problem.

  Please, I'm at a loss to date.

  Yours Sincerely,

  Leon

  Hi all

  Seems that I myself have found a potential workaround.

  Install only the KB2871389 allowed me to grab the download of Windows the Windows store 8.1.

  Then, I could install Windows 8.1 without a hitch and it normally seems using Windows Updater runs from there on.

  It is not yet a waterproof solution to water / final of 100%, but it seems to work for me.

  I hope this will help someone else with the same problem!

  Yours Sincerely,

  Leon

• Failure of windows updates changes to recovery (using Windows 8). Turn a computer off

  I did a refresh with Acer laptop and lost everything. RELOADED Office 2013 and some applications after if and it seemed to work.

  I went to then turn off the laptop and he tried to update about 72 updates. After 30 minutes, the message "preparation set up windows" do not turn off computer. When he tries to restart, the message "failure configuration windows update changes back? rises.

  He continues to do in cycles?

  Help

  JOhn

  Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates
  http://support.Microsoft.com/kb/949358

  You need to disconnect all your removable media to the computer, such as removable disks (Blu - ray disc, DVD, CD), the memory cards (CompactFlash, Secure Digital card, Memory Stick card), and USB flash drives.
  These removable media can cause this problem during the restart of Windows.

  or

  System restore - Note if your computer is not configured to start from a CD or a DVD, or if Windows was preinstalled on your computer without the CD or DVD, see the documentation that came with the computer for instruction about how to continue, or go to the next method.

• Surface RT - default configuration Windows updates to returning date change

  I just bought a RT of Microsoft Surface 32 GB and I tried to upgrade to 8.1 Overview Windows.  The device off near the end of the installation and when I turned on this return, he cancelled the installation.

  After the installation is rolled back, I had to go through the installation process for Windows.  When I am finally back into Windows it had only four tiles on the start screen: IE, store, Explorer of files and office.  Other applications, as well as UNRWA, have been installed is no longer.
  I tried to do a system restore, but it says that there is not all the required files and insert the installation media.  Unfortunately, I did not create a restore USB.
  Now, whenever I try to install updates from Windows Update it restarts and starts to install, but then comes up with the message "configuration of the Windows restore changes updates failed.
  I have redownloaded update for Windows overview 8.1, but even after installing and rebooting I don't get the option Update in the store.
  someone at - it ideas?
  Thank you
  Jason

  Hi Jason,

  Do you have a code/error message when installing Windows RT 8.1 Overview has been restored?

  In order to upgrade to Windows RT 8.1 overview you should have a good peripheral work of RT. Since the rear roll was incomplete after the failure of the installation of Windows RT 8.1 Overview, some of the preinstalled applications are missing from the device. So, I suggest you "reset your Surface. Please refer to the section: "Solution 3: reset your Surface" from this link:

  http://www.Microsoft.com/surface/en-us/support/warranty-service-and-recovery/how-do-i-restore-refresh-or-reset-surface

  Note: All your personal files will be deleted and your settings will be reset. All the apps that the is come with your PC will be reinstalled, but all other applications will be deleted.

  -After the reset of the device, install all the updates that are available from Windows update and make sure that the device is functioning properly.

  Please return back with the State of the question after the above given steps, so that we can help you further.

• Default configuration Windows update restore changes do not turn off your computer.

  I'm running 64-bit Windows 8

  Guard saying default configuration of folds by using Windows Update

  Hi Cris,

  Thanks for posting your query in Microsoft Community.

  You did it any significant hardware or change software on the computer before this problem?

  I understand that you can not install some updates with the error message "failure of configuration of the Windows updates...". ». I can imagine the disadvantages suffered by you and will certainly help you in the right direction to solve the problem.

  First place, according to the error message, I suggest you to try the steps in the following article and check if it helps.

  "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"error when you try to install Windows updates

  Note: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  
  

  The question may arise if the Windows downloaded update packages are corrupt. So, if you are able to start the computer successfully after following article provided above, I also suggest you try the following steps and check if the problem persists.

  Method 1:

  Try to run that Windows update utility provided in the following link.

  Problems with installing updates

  Try to install the updates after running the troubleshooter.

  If the problem persists, try the following method.

  Method 2:

  I suggest you to use Deployment Image Servicing and Management to fix Windows Update errors.

  (a) open an elevated command prompt. To do this, press the Windows key + Q and type in CMD right click on command prompt in the list and select run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  (b) type the following commands. Press enter after each command

  • DISM.exe / Online/Cleanup-image /Scanhealth
  • DISM.exe / Online/Cleanup-image /Restorehealth

  (c) close the command prompt, and then run Windows Update again.

  Check if the problem persists.

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• "Unable to configure windows update, changes the way back" takes too long...

  My PC just newly formatted and now I can see a problem when I turn it off, he just starts to day and after that it fails... I'm worried about what it takes too long... from 10:00 until 16:00? I read an article on them, she'll just take up to 20-30 minutes, but watch?

  Is there something I can do? Can normally on my return from PC? or what I need to reformat?

  Hi Andrei,

  Thanks for posting your query in Microsoft Community.

  I understand your concern, and we as a community will try to help you in the best possible way we can.

  Here are solutions to some common problems with installing updates. You might be able to fix some problems automatically by running the Windows Update Troubleshooter.

  I suggest you check out the link below and check if it helps.

  "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"error when you try to install Windows updates

  https://support.Microsoft.com/en-us/KB/949358

  Hope the information helps, if you have any additional questions, feel free to post. We are here to help you.

  Kind regards

  Guru Kiran

• Failure to configure Windows updates, changes to restore, do not turn off your computer.

  I had this problem for about 3 hours now.

  I have a laptop called Lenovo G580, before it all went past, he had to restart while I was navigating apps send me 14 minutes to prepare.

  And then it goes up to (15%)? Then gave me the problem "configuration of the windows updates failed, restore changes. Do not turn off your computer "

  It took a while, so I had to turn it off, but he returned to the screen, same problem all the time. It does change a bit.

  It restarted once but it comes back to the same problem

  I'm not sure what I can do, I just leave and wait until the early morning hours or y at - it a specific solution for this or anything like that?

  Help please!

  Start here: http://support.microsoft.com/kb/949358

• I'm getting 'Failure Configuring Windows Updates, changes of restoration' by updating windows.

  It was the first time that I am trying to update my laptop of Lenovo G500s which is come with 8 windows pre installed, before installing the updates, I have restored the laptop if you default factory using Lenovo a recovery key. While the updates are being installed I received a message 'Fail configuration Windows updates reverting changes'. It lasted for an hour. When I tried to install updates again the same message appeared. My laptop came pre-installed with Nitro Pdf 8 and Mcafee Internet Security, so I have even uninstalled them, I also ran Mcafee Consumer Product Removal Tool. But the problem with windows update remained. I then ran the convenience store update Windows that sets these two problems:

  fix windows update fixed the database and repair misconfigured update windows components, but this solves nothing. Later I discovered that although the resolution of update problems show that the problems have been solved but convenience store running immediately shows again the same problems.

  So this time I ran again the recovery system, and immediately after the system recovery windows update of convenience store that showed the problems mentioned above two updates of windows.

  Is it so that means the recovery partition itself contains other problems that my problem would have been solved, what do I do to fix this?

  Take a look on: http://support.microsoft.com/kb/947821/en-us

  ... use the Deployment Image Servicing and Management (DISM) Inbox. Then, install the update or Windows service pack again...

• I use vista home premium.i am the only user. In windows update, change the settings, I noticed information as "some settings are managed by your system administrator" under updates important, I can not access or change the settings.

  recently, I tried to change the reg key by going to "HKEY_LOCAL_MACHINE\SOFTWARE\POLICIES\MICROSOFT\WINDOWS\WINDOWS UPDATE\AU" in the right panel, I changed my reg AUoptions value to 0.

  I'm using norton 360 (ver 2.5.0.5) .no other norton is installed.my subscription will be emds after 865 days.
  
  UH - huh. You have 2¼ ~ years remaining on an N360 2009 subscription. I see.

  In this case, the Symantec Support should be able to help you eliminate the hijackware infection which is causing your problem.

  Good luck!

• WINDOWS UPDATE 'change settings '.

  I am the administrator of my PC running windows 7.  I noticed that in the "Edit settings" window of WINDOWS UPDATE there is a? Info sign telling me that "some settings are managed by your system administrator...". "and I no longer have the ability to choose when and what time IMPORTANT UPDATES are made.  Can you please tell me to use this option. Everything seems to work properly, the updates work.  Thank you very much.

  Hello

  Thanks for your reply. I watched your method 2 solution and thought it was a bit too complicated. So I thought why not try a "restore to an earlier date."  When I tried, there was a problem with the RESTORE process and I was brought to the screen of the REPAIR of the SYSTEM . I clicked on 'repair' and after a few minutes of waiting, I was led to my login screen. I logged in... went on control PANEL and Windows update and noticed that I had my return Option! Everything is back to normal.

  Thank you

• Windows updates keep neglecting returns and finally starts successfully.

  Hello

  I have to be ongoing problems with Windows Update failures for several months and nothing to do, it seems to me and nothing from what I've read online seems to help.

  I have a laptop Acer E1-531 runs a 64-bit version of Windows 8.

  Almost every time that the laptop starts, it tries to install the updates fails (3 times), comes back and finally starts successfully. It takes anywhere from 10 to 20 minutes.

  Can someone please? I'm desperate.

  Thank you

  Hi Mark,

  Microsoft updates are getting failed?

  This problem may occur when you try to install Windows updates, Windows failure configuration updates. Restoration of the changes. Do not turn off your computer.

  I suggest you to try only Windows 8 steps from following link and see if that helps.

  "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"error when you try to install Windows updates
  http://support.Microsoft.com/kb/949358

  Note: Follow How to reset the computer to start as usual after a clean boot troubleshooting article KB929135 to reset the computer in normal mode. Also when you do the system restore, you will lose data and the programs that are installed on the date you make the system restore.

  Note: Perform an upgrade on the spot will restore you the current installation of Windows for the version of the installation DVD. It also requires the installation of all the updates that are not included on the installation DVD. If your computer came with Windows pre-installed, see your computer documentation for instructions on how to do an upgrade on the spot. Otherwise, follow these steps.

  I hope this helps. Let us know if you have other problems with Windows in the future.

• failure of windows updates changes in recovery

  Said widows update of components need to be repaired.  Help, please!

  Use the following tutorial to reset Windows updates completely and check if it helps:

  Reset Windows updates

  Be sure to run the script as administrator.

• Windows Update changes home page

  I have VISTA. My Yahoo is my home page. 2 days ago, that the pg suddenly changed while I was away from the computer. The menu file/Edit/View/favourites at the top of the pg bar disappeared. My Yahoo logo, who was also at the top of the pg that I used to open additional windows have also disappeared. I tried to find help on Google, other sites. Only info I found indicated that Internet Explorer 7 now hide this menu bar. I don't know how to find out what version of IE I have.

  I managed to get the back bar menu (no idea or how I did in fact). The logo of Yahoo, I used to open windows to the addl is still missing. The homepage has now 2 gold stars above the pg who will open a list of favorites to the left of the pg that I don't like because then there's no room to see the rt page. I find the Windows constant updates of the circumstances aggravating and annoying & sometimes Cancel when the window appears. I don't know if this problem was a result of an update or not, since I wasn't on the computer at the same time.

  loricherokee, it seems that you have updated your browser to a newer version, it is a very important and not beneficial because it gives you a stable and more secure application for your internet browsing. You might have had a Yahoo toolbar program installed and that's what you're like the yahoo logo, referring to East - this exact? If so, you can go on yahoo and acquire again.

  For the menu bar, simply press the ALT on your keyboard to see. You can then use the Favorites option which is similar to your old way (I assume you were using before IE6), or you can always together favorite button to close the column which is located on the left.

  To set your home page you can click on tools, Options and in the general, either type the link to your home page or click use current to set the page your on your homepage.

  Please visit the following page for more information on Internet Explorer 7, click Take a Tour on the right.
  http://www.Microsoft.com/Windows/products/winfamily/ie/default.mspx Rami
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.