Default mode IDE of DCIS vice, is the SATA controller?

Similar Questions

• Aurora R4: newly installed SSD running in G2 / SATA300 - how can I 'persuade' the SATA controller to run at G3 /SATA600?

  Good evening.  I was a little indecisive on the place where this post, but I think it's the right place.

  I just replaced the main drive in my Alienware Aurora R4 with a SanDisk Extreme Pro SSD... works perfectly (and quickly).  I realized a clean Windows 10 Pro (x 64), generation to level to the latest version.  I'm not using RAID.

  The SDS is properly installed and connected in the location SATA01.

  This Aurora R4 has the "Dell", well actually "Intel" Patsburg 6 Port SATA AHCI Controller (revised A7), capable of handling G3 / SATA600.  However, two DVD players work to G1 / SATA150 and all four disks are running at G2 / SATA300.

  I have the latest driver for the Intel Rapid Storage Technology technology, confirming a transfer rate SATA 3 Gb/s for my SSD (and the other three HARD drives).

  How can I convince the computer I want to optimize my SanDisk Extreme Pro SSD performance, with the rate of transfer running at G3 / SATA600?

  I searched on through the value of the library of web pages, but not found a solution.  I was hoping that it would be a BIOS problem (installed last), is a question of the SATA controller firmware, but that doesn't seem to be the case.  Technology Intel Rapid Storage Technology driver allows no fiddling, so I drew a blank there.

  Knowledge advice would be warmly received, especially if you have a R4 Aurora that runs a G3 SSD / SATA600!

  Hi Domo_P1000,

  You can search the forums to Alienware for help with this. I found this relevant thread.

• Tecra PT634E A50 - need details on the SATA controller

  Hello

  I am looking for detailed specifications of Toshiba Tecra A50 (PT634E-00800JPL).
  I need to know what the internal port SATA version.
  What is SATA II or SATA III?

  I want to change the SSD hard drive and buy the most appropriate.

  Install the software of diagnosis equipment freeware like Sisoft SANDRA, Everest Home Edition or HWiNFO32.

  These tools provide you with all the essential information on the integrated parts and the HARD disk controller.

  Please post feedback would be interesting to know what details SATA controller would be declared by these tools.

• Satellite U400-183 lower upgrade to XP - driver for the SATA controller

  Hello

  There is a blue screen during the installation of xp because the missing drivers (SATA controller).
  Could not find the driver, nor on the toshiba Web site on intels.

  Someone who can help? Thank you very much.

  Stefan

  Hello

  Satellite U400-183 seems to belong to the series of PCU44E. Right?
  The European driver Toshiba page provides the drivers for this model.
  You can find on the page of the driver for Win XP Intel Storage Manager and this package contains the SATA drivers.

  But look, man here in the forum, you can find many comments about the installation of the SATA driver why you n t use the search option?

  The best way to install the SATA drivers is the use of nLite.
  He tool free s (you can find it on the internet) and it helps you integrate SATA drivers into the Win XP disc!

  I did it and it worked for me

• Compatibility of the SATA controller

  I am in the planning phase of construction of an esxi 4.x system equipment and try to get compatibility info sata controller. I searched but the info I found are limited, I looked at the list of compatibility with vmware and they list only 3 controllers, I'm sure that more than these 3 will work.

  Can someone point me to a site that lists the controllers sata that people have tried and worked on facilities there?

  Thank you.

  The hardware compatibility list is on VMware / supported material supplier. You can see http://vm-help.com for a list of hardware not supported that worked. If it is at all a production environment use the VMware HCL. With hardware not supported you risk inconsistency or instability to every update / update.

• Change the SATA controller AHCI RAID mode

  HP Pavilion 6267c desktop 750 gb HD failed.  Installed Seagate Barracuda 1 TB HD.  Cannot change the controller SATA AHCI RAID mode.  System hangs.  Desktop works when he returned to RAID.

  Any help is appreciated.

  Hello

  Hope this helps:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/changing-from-RAID-to-AHCI/4c94f678-6BD1-48a6-b871-8872c841023a

  Good luck.

• How can I change the SATA controller to ide on hp pavilion dv6-6c50us with windows 7 Home premium? I want to install win xp on my external hard drive.

  while I try to install win xp on my external hard drive using my computer with win 7, an error with blue screen pop out.

  ERROR: 0X0000007E

  ACPI.sys address F73B8D66 base at F73AD000 DATER 41107 27

  You will need to load the BIOS and make the change.

• I want to change my win8 to winxp for my laptop, but I cannot driver for the sata controller.

  Hello

  I have a laptop which is HP 2000-2d28CA laptop. I install 32-bit winxp for some software that I really need. I could not find the drivers for my laptop. My chipset is AMD ID1536 and shouthbridge is AMD A55/A60M and lds material are

  PCI\VEN_1022 & DEV_7804 & SUBSYS_2128103C & REV_00

  PCI\VEN_1022 & DEV_7804 & SUBSYS_2128103C

  PCI\VEN_1022 & DEV_7804 & CC_010601

  PCI\VEN_1022 & DEV_7804 & CC_0106

  Can someone help me for this

  Thank you

  You are the very welcome.

  Unfortunately, I wouldn't know how to help you with the problem you are experiencing.

  You can try W7 32 bit, but you have to hope that AMD has a 32-bit driver for the graphics card on your laptop because HP does not work.

• Problem with the installation of the SATA controller drivers

  Hi all

  Here's the situation

  HW:

  MB - Supermicro X7DBP

  CPU - 2 x XEON E5430 @ 2 .66GHz

  RAM - 16 GB

  Controller SATA - raid serial ata 3ware 9650SE-4LPML

  HDD - 1 x Seagate / 1 TB

  I installed ESXi 5.o on the USB and it starts OK, but does not recognize the drive HARD (planned).

  Download scsi-3w-9xxx - 2.27.08.036 - 1OEM.500.0.0.472560.x86_64.vib (3ware driver)

  Copied from .vib to the ESX Server (in / Temp dir)

  Connected to the console via ssh client

  you try to start esxcli vib install software...

  console answers with:

  -sh: esxcli: not found

  What I am doing wrong?

  Thanks in advance

  perfect!

  and Tom don't forget to mark it as answered and helpful.

  Thank you.

  Kind regards

  Julien

• There is an option in the bios to set the sata drive * IDE *-mode?

  There is an option in the bios to set the sata drive * IDE *-mode?

  Grobi

  Hi dude

  That s a funny question.
  No, there is no option in the BIOS!

  Please understand that there are various interfaces to drive HARD. IDE and SATA.

  There is a big difference between the two interfaces and the function of the HARD disk on the motherboard controller, you could use a HDD IDE or SATA HDD.

  But you cannot connect a SATA HDD to IDE or IDE HDD controller for the SATA controller. This is not possible due to different hardware.
  This is not possible and that's why these BIOS settings are not available or don t exist!

  Good bye

• Satellite Pro P200 - 17 c: Win XP won't load - installation of the SATA driver

  Hello

  I have a satellite pro p200 - 17 c I've had good years, allways worked without any problem.

  Last week when I booted the laptop, windows won't load and I find myself safe mode selection screen. No options whatsoever me to windows loading, I tried F8 and still nothing.

  I tried the restore cd that reimagee the drive but I get the same thing, I tried a new hard drive, once again the same.

  But if I try to load windows from an OEM to install that software does not because it is a sata drive and there is no floppy drive. I have an external floppy drive I use, but it is not known now.

  Any ideas or suggestions?

  Hello

  Go to BIOS and set it to default settings.

  In this case the SATA mode must be on AHCI. In this case the SATA drivers are required to install the Windows operating system. But as much as I know that Windows 7 already contains the SATA drivers if usually you don t had to add SATA drivers while OS installation the installation program.

  However, here is a nice HowTo document that helps you add SATA drivers for Win XP installation disc.

  + How to integrate a SATA AHCI driver into a Windows XP Setup CD.
  http://APS2.toshiba-tro.de/KB0/TSB85017Z0000R01.htm

  + How to integrate the AHCI driver during the installation of Windows XP.
  http://APS2.toshiba-tro.de/KB0/HTD9401AN0000R01.htm

• Re: Satellite L300 - how to reinstall the SATA drivers?

  Hi all

  I have a L300 I downgraded to XP. It runs with the SATA controller in compatibility mode and are sent here a lot, it's slow.

  I read you need drivers intel for her and so I downloaded the and down them and had an error "your computer does not minimum requirements.

  Tried in both safe mode and got the same error.

  Now I could try to use nlite and I've used it before, but the file I have is an executable and not an inf and files related to a driver, so I don't know how to add it to nlite. I'd rather do not re - load again if possible.

  So the simple question is how I install the AHCI SATA drivers so I don't have to run in compatibility mode.

  Thank you

  Mick

  Hello

  I think that you should use the forum search. You will find the sufficient number of threads how to install SATA drivers

  In addition this s one interesting article step by step:
  http://APS2.toshiba-tro.de/KB0/TSB85017Z0000R01.htm

• HP Envy 15-j001sr: SATA controller in AHCI or RAID mode?

  I wonder, does anyone know how the SATA controller located in

  HP Envy 15-j001sr (E3Y72EA): in RAID or AHCI mode? I buy this laptop and planning to upgrade to SSD.
  Upgrade advice will be highly appreciated.
  What is better: to clone the HDD SSD before initial start-up
  Or install Windows8 first, bring a USB recovery set, then make Windows8 recovery after the installation of the Virgin SSD in?
  Thank you for your help in advance.

  Hello

  It uses a single disc HARD must be the AHCI mode:

  http://support.HP.com/us-en/document/c03846066

  You can configure it as you want, including create whole recovery dics and THEN clone the disk SSD. After that trade them. This will save time and you can be sure that the rollback/uninstallation less pain if necessary.

  Kind regards.

• Reset Snesor signature to the default mode

  Salvation of the Forumers

  I would ask anyway I can reset my default mode VS signature?

  My platform is ASA 5510 SSM-10, running on IPS v7

  Thank you

  Noel

  SSH into your sensor, and then run these commands:

  conf t

  sig0 GIS service

  default sig

  -Bob

• Cannot change the default mode in wscript

  In Windows 7, when I try to change the default mode of wscript, I get an error message. When I get home

  CScript //H:CScript

  the command line, I get

  CScript error: cannot change the default script host

  What should I do?

  Open command prompt w / administrative permissions (right click, run as administrator), and then run the command:
  cscript //h:cscript //s //nologo