DELL PowerEdge R730 (Gen 13) always 100% fan (16000 RPM +)

Similar Questions

• RAID 1 support on Dell PowerEdge R730 with SSD and Perc H730 discs

  Hello. I am looking for some info on RAID usage with SSDS on our server:

  Dell PowerEdge R730
  1 GB for the PERC RAID controller cache internal H730
  200 GB Solid State Drive SAS mixed use MLC 12 Gbit/s, 2.5-inch
  OS Windows 2008 R2 (for now)

  We would like to know if it is supported to use two SSD drives in a RAID 1 configuration.

  What are the risks?
  Suggestions for others / the best solutions?
  How the controller or the handle of the Garbage collection, Trim and other techniques SSD SSD?
  Are there solutions in place for Wear leveling and how do they work?
  What are the methods of protection for the I/O failures for these SSD drives and / or PERC controllers?

  I hope you can answer (some of) the issue or point me in the right direction for some Dell documents on this subject.

  THX

  Arjan

  Hello Arjan

  Yes, you can use SSDS in RAID 1.

  The controller supports the TRIM and cancel orders mapping. SSD MLC are grade consumer SSD which will not have the life expectancy of SLC.

  http://i.Dell.com/sites/DocContent/shared-content/data-sheets/en/documents/Dell-PowerEdge-RAID-controller-H730.PDF

  http://www.Dell.com/learn/us/en/04/campaigns/Dell-RAID-controllers

  Thank you

• Portege M400 - always 100% fan running

  I was pleased to receive my new toshiba portege m400 today, but the noise of the fan is quite bad.
  The problem is that he always runs 100% - I tried the Toshiba power save the properties of
  set the speed of the fan, but nothing is made, it has no effect at all. Also, I tried to put
  all three bios power options (low, full power, user), but that has no effect either.
  Worse still, the cpu temperature is very cool, just 29 degrees, and there is no need
  at all to run the fan at full speed. I guess that the power save utilities are bugged, and I wonder
  If Toshiba will come out with a new version of their tools? Is there something I can do?

  Thank you
  -Daan.

  PS. the version of the bios 1.30, toshiba power save tools 7.08.00. The processor speed is dynamic, generally at 1 ghz and
  the temprature is very low.

  [Edited by: admin April 20 06 06:48]

  Hello

  Try to clean the cooling modules. You can use the vacuum.
  In addition, you must use the laptop in the places where fans can suck the air out without any problem.

• Is - this motherboard for Dell Poweredge 2900 gen. I, or GEN III

  Hi @ all,

  I recently this MB + accessories from a friend and I wanted to get this in life now. But to do this, I need some information about it. If I can get the right processors

  According to my friend, this MB support socket 775 CPU, but according to the data sheet @ dell.com, it supports socket 771 processor. Now, I'm a little confused about the...

  the MB model is: CN-0TM757-13740 - 74G - 0278 REV A01

  I hope that someone can give information me...

  Thanks in advance!

  Greetings from the Germany

  Benny

  I'll add pictures to this post as well

  

  It is a mother Board of generation 1 for a PowerEdge 2900 server.

  Your friend is wrong, the documentation is right (go figure): Socket 771.

  Xeon 5160 is the best processor released for this version of Office.

• Dell PowerEdge R730 + ESXi 6 U2: licensing problem bought

  Hello

  I am trying to assign vSphere Standard licenses, I bought via Dell (and saved).

  Whenever I try to license, I get an error message:

  "The entered license key has no sufficient capacity for this entity.

  Has anyone ever had this problem?

  I have dual CPU servers (so I bought 4 licenses) that they are by CPU.

  VmWare does not seem to understand my problem.

  Kind regards

  Hello

  What model CPU do you have? https://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1019695

• Dell PowerEdge R730 Rack Server

  Dear support team, I need urgent help here...

  I have to have to Open Dell Management CD to install windows and I installed windows server 2012R2 without using the disk operating system that lead that now lack of drivers.

  So my question now is how to update the missing drivers from the CD, avoiding reinstall OS again because I already have the full installer for my applications...

  Waiting for your answer...
  Kind regards

  Solved by going to dell driver > chose my product and download and installed (Drivers-for-OS-Deployment_Application)

• Dell PowerEdge 2900 Gen 3 storage issue

  Server is updated the firmware and the BIOS has to SAS6 6i controller. Operating system is Ubuntu Server LTS 14.04.

  Drive is a 4 to Seagate...

  Appears in gdisk and present as only 2 TB. If I pop the drawer and put it in a server Win2014R2 with UIEF/EFI BIOS, it says 4 TB.

  Is this a problem with the system BIOS or the firmware of the controller?

  Hello

  MAFoElffen

  Is this a problem with the system BIOS or the firmware of the controller?

  There is no problem. Maximum drive size supported on the 6 SAS is 2 TB.

  Thank you

• Dell PowerEdge Fans always runs in full speed

  Hello

  I have a problem with a Dell Poweredge 2900 server witht. The server is still running the fans at full speed.

  I tried to update the latest version of the bios and the firmware for environmentally sound management, but the problem is not resolved.

  Dell OpenManage shows only a single error, said of the intrusion into the chassis, casing is open, but case is closed properly. I think that the sensor is bad, I try to look for the switch, but I can't.

  Please let me know where is the switch of intrusion of the chassis on this server, or how to disable.

  Thank you

  As suggested by Theflash1932, the intrusion switch may be damaged and located on the Bay of housing Center fan. It cannot be replaced as one of its components. See the image below.

  

  It is replaceable like a Bay of housing of Dell part number: NF078

• CPU is always 100% always

  Hello

  I already connected my problems here

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-performance/WinXP-SP3-messed-up-with-IPC-errors-task-bar-color/3a194637-CC25-4f82-9BD8-3156f996652d

  with not much help, I tried the system restore... In fact this is the point where I have no DOUBT (not sure) had installed the drivers from Dell.

  Now the only issue is resolved is the taskbar which is now back to normal... However, I have now even serious problem...

  CPU is always 100%... always...

  The task CPU usage

  eGUI.exe 01
  Svchost.exe 31
  Svchost.exe 17
  services.exe 26
  Taskmgr.exe 01
  ekrn.exe 21
  System 03

  varies around him.  Does not open Firefox and IE opens after a long time. . any help to solve this problem would be appreicated.

  See you soon

  -Newxper

  Thank you Andrew and Elizabeth23...

  I had this problem fixed. I ran the combofix and I have my cpu use is that technology should.

  Thank you

• CPU usage always 100% after installing Vista SP2

  Hello

  I am currently running A Dell Dimension B110 with 1 GB RAM 256 mb nvidia geforce 6200 (pci), 2.6 ghz celron D and Windows Vista Home Basic SP1.  It works nice and fast.

  That is until I have install SP2.  Then the CPU usage is always 100% when running anything (with the exception of the Windows Explorer), and the pc is running very slowly.  To solve the problem, I went back down to SP1 and everything goes quickly again.

  A few weeks later, I tried again and the same result.  So I returned again back to SP1.

  For future software versions, I need SP2.  Does anyone have advice and/or corrections to this problem?

  Thanks in advance

  -One5860

  https://support.Microsoft.com/OAS/default.aspx?PRID=13014&Gprid=582034&St=1

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support for SP2 is valid until August 30, 2010.

  Microsoft free support for Vista SP2 at the link above.

  See you soon.

  Mick Murphy - Microsoft partner

• Dell PowerEdge Server - IDRAC R720 problem

  Dear support team

  I have a Dell PowerEdge R720 not ready iDRAC server. The configuration values are not available. very strong fans noise, please notify

  Hello

  I'll send you an email to ask for the serial number. Thank you

  Marco

• Supporto brain fees by PowerEdge R730

  Buongiorno,

  Ho UN PowerEdge R730 labor-intensive e I like cute brain che abbiamo gia fees to casa.

  Osservo che is cute I have brain su una dell'apposita sleigh. E' possibile acquistare queste slitte?

  Buongiorno,

  slitte del Server non sono acquistabili como iPhone, we can is sostituirle to una di essa malfunzionante e.

  Marco

• ESXi 5.1 updrade to 5.5u2 PowerEdge R730

  I had a few R730 brand-new which comes preinstalled with ESXI 5.1 u2, on flash cards double and the size of each of them is 7 GB

  What is the procedure to upgrade the esxi 5.1 to 5.5 on PowerEdge R730 using the iso dell custom", and 7 GB will be sufficient for the upgrade process?

  Thank you

  * boot ISO shows datasore and two data warehouses 7 GB 300 GB *.

  Alshawwa,

  The process is simply to run the update with the ISO custom. I guess that the hypervisor resides on SD cards, so if this is the case, then select for update. The 7 GB is more than enough space for the hypervisor and upgrade. ISO is just show hard drives, as well as 2 redundant (7 GB) SD cards.

  Let me know how it goes.

• Dell PowerEdge 2900 RAID and drive down

  I have a Dell PowerEdge 2900 server. The primary transmission table has three drives and RAID 5. The system came this way, and it has been humming for quite a long time. Recently, one of the disks has deteriorated and the light on the drive flashes green and light amber. The light amber, I figured, it means that there is a problem with the drive and must be replaced. Then, I found a replacement on Amazon.com drive and installed (the drive is hot, but my cold started to be sure). I installed the drive, but keeps flashing green and amber light.

  I didn't know that I shouldn't have to replace the drive in this way, so I will now try to figure out what to do next. I hoped to reallocate the foreign disk so that I can use it, but my server always shows the reader, not having even if the new replacement drive is in the slot, now.

  I'm running PERC 5 / I integrated utility of Configuration Bios 1.04 - 019 a

  I started the server and you press CTRL-R. I've highlighted the controller and press the F2 key, what is operations. When the operations window opens, there are three menu items:

  Create new VD
  Zero Config reset
  Foreign config

  The only thing that I am allowed to do in this menu is to reset the configuration. I can't move my cursor upwards or downwards for one of the other choice of two menu.

  Scroll when the virtual disk and he discovers, it still shows the first two discs and a lack.

  When I press CTRL + N to display the next screen, I see a player listed as failed.

  How can I rebuild my RAID with this new drive? If I can't do it, what is the best way to remove the RAID and start over? If I delete the RAID and do it again (and if my replacement drive is indeed well), how can I make sure that my server not to see it, not having so that I can start using it?

  Alternating flashing green/orange means that the disc is in a status of predictive failure. What OS is running system? If you hotswap drive next failure they may possibly other issues table because the drive was online and participating in the table with errors on the disk. The adequate alternative method is to use our software Openmanage Server Administrator to run a consistency check on the table and then the drive offline. Once this has been done you can then swap the drive. It seems that in your case, that the new drive had bad data copied on it and it made a predictive failure as well. We want to do is run our hard drive diagnostics and test drives in the system.

  http://downloads.Dell.com/FOLDER01456532M/1/Dell-onlinediags-Win32-2.30.0.70.exe

  Install and run the GUI version in the start menu. In the left pane select the PERC 5 and then in the lower right pane select quick test and then to run tests.

• Card LaCie esata PCI card on windows 2003 server Dell poweredge T410 error code 10

  Hi guys, I am trying to install a new card Lacie esata PCI card (http://www.lacie.com/products/product.htm?pid=11217) on windows server 2003 on Dell poweredge T410. Windows detects the card and install the driver, but then, it shows an error code 10 "device Can not not started. I tried the update, uninstall, reinstall, adding Lacie driver CD through the "Hardware Wizard', chaning PCI card slot by 4 to 1. But nothing has worked. So please let me know if you think that there is a fix for this solution. Thank you

  Hi Rlap,

  The question you have posted is related to Windows Server and would be better suited to the TechNet Discussion groups. Please visit the link below to find a community that will provide the support you want.

  Windows Server Forums: http://social.technet.Microsoft.com/forums/en/winservergen/threads