Dell R610 RAM configuration

Similar Questions

• iDRAC on Dell R610 problem

  Hello

  I just got a new Dell R610 and I tried to configure the iDRAC on her card. I have it configured on interfaces of multiple T300 Dell and the ILO on the different models of HP servers successfully. But for some reason, I'm going to have serious problems with it.

  I think he got an iDRAC Express card as there is no extra ethernet port on the server, just the standard 4 integrated NETWORK interface the iDRAC BIOS are version 1.70 I understand is the last.

  In the screen configuration (Ctrl + E) iDRAC, iDRAC and IPMI over LAN are enabled. Selection of NIC is set to shared so for active LOM, it reports 'No. Active LOM'. VLANs are disabled, iDRAC Express stand them? -Once it works I would like to enable it if possible.

  Only NIC1 (eth0) is connected to the switch. I tried configuring it with DHCP, but he never does an address even if the operating system gets a.

  To remove the switch / VLAN even tried to connect NIC1 directly on an other server tcpdump and running with iDRAC configured with a static IP (the default value of 192.168.0.120). Did not get a thing of it. I could see the arp requests going out but not responses to iDRAC.

  So, how do you get the iDRAC to work?

  Thank you.

  Today technician Dell replaced our motherboard and this fixed a problem with the DRAC.

  New motherboard uses older versions of BIOS and DRAC BIOS main:

  principal: was 3.0.0, now for 2.0.11
  DRAC: was 1.70.21, now 1.41.13

  DRAC works now, and, Yes, she has the web interface.

  PS unfortunately, but this will not be fixed another issue we have with H200 controller or it's linux driver mpt2sas: https://bugs.launchpad.net/linux/+bug/777441 (ClxAdmin, if you use Linux on that server, what distribution of linux/version you are using?)

• Server Dell r610 with PERC 6 / i controller

  Hello

  M using dell r610, which is configured with PERC6 / i controller, problem is I want to know when I configured the RAID-0 and remove my disk only, fails to get the boot, how to solve this problem?

  Once again, I want to know:

  1. with the raid configuration are we able to expand the size of the disk (from 2 TB to 3 TB) without lossing data

  2 are we able to use this server with No.-raid because raid will be risky in the case of a disk failure and won't lose data...?

  ((1-Yes, you can, but ONLY if 1) your system is currently in UEFI boot mode and 2) you are not currently using a RAID 10 (or have several bays on the disks).

  2 n ° on PERC 6 does not support the RAID/JBOD. RAID is ONLY risky if the USER chooses a risky RAID level (RAID 0 should be used for specific reasons by experienced professionals).

  RAID 0 has NO fault tolerance.

• Installation of the H700 controller in dell R610

  I asked this question on serverfault.com but so far do not have a definitive answer.

  We just put a refurbished dell R610 2 X 6 Core X 5650, 96 G Ram, Raid SAS 6ir controller, 2 X Fujitsu MBC2073RC 2.5 15 K 73 GB SAS Hard Drive. We will also install additional disks:

  • 2 x Intel 730 480 GB 2.5-inch SSD SSDSC2BP480G4R5
  • 2 x Samsung SpinPoint ST2000LM003 2 TB 2.5 Momentus "

  I also separately brought a controller Raid H700 renovated to use rather than the SAS 6ir map. This is the integrated H700 and looks like this:

  How to install this? I have read several books looking for instructions explicit (Page 111 of the operating instructions R610 is not quite clear to me...) For example should I unscrew the cache-pci slot metal on the left side of this map and then directly replace the Board SAS6ir "integrated"? Or go to this card in a separate pcie slot? (I don't know the cables will reach and I'm not sure the cable management) Does anyone have pictures of an installed H700 and PERC, installed in a R610 battery?

  Thank you!

  Jason

  sysjas

  is the only difference between the version of the built-in adapter and the internal version of the pcie metal plate?

  No, the main difference between the two integrated and adapter's firmware. They are designed to work in the type of the specified location. The integrated storage location is a PCIe location, but it works the same as a normal PCIe location.

• ESXi on a DELL R610 Server

  Hello

  being a newbie on VMWARE ESXi 4, I use the software on a DELL R610 server with 1 INTEL XEON X 5650 processor and 24 GB of RAM (6 x 4 GB).

  This system 4 servers and 4 offices is hosted.

  To improve performance, I want to add more memory 36 GB (3 x 4 + 3 x 8) and I think a second Xeon processor.

  A second processor usage is possible with ESXi 4?

  Web search gave me a confused littlle bit, due to contradictory answers :-(.

  Best regards from the Germany and thank you for useful answers

  Torsten

  On the RAM that you want to add, please make sure you read http://kb.vmware.com/kb/1018754

  André

• Inventory of the Dell R610 collection system

  I have 2 servers Dell R610 x. ' ' We're heading quickly through POST while the other drops in "inventory of the collection system" for about 10 minutes before you start.

  Is there a way to disable the 'inventory of the collection system' on each startup?

  USAO,

  Yes, there is a way to disable the system inventory collection on restart (CSIOR).

  1. Access the iDRAC6 Configuration utility by clicking on during the POST.
  2. Select System Services in the main menu.
  3. Change the inventory of the system collect on the configuration of restart for disabled.

  See a similar screen capture below:

  

  Let me know if you have any other questions

• Reference Dell r610 slow start

  Hi I have a Dell r610 but it takes a few seconds at startup I had 48 GB of ram, I just checked that everything is ok regarding the ram, hard drives, my bios is version 2.0.13 What can do to optimize it?

  Thank you

  Hello

  I wouldn't recommend trying to speed up the process of startup/POST. The more material you have in the slowest server, it will be. You can speed it up the disabling features such as memory controls, inventory (CSIOR) or the controller of the lifecycle altogether. You can also disable firmware for some hardware interfaces.

  http://www.Dell.com/support/home/us/en/19/product-support/product/PowerEdge-R610/manuals

  Thank you

• Replacement Dell R610 motherboard model number

  As I have no further with the tension E1000 Failsafe error. Contact technical support. The next thing to do I think is to replace the motherboard of Dell R610. Looking on eBay there are a number of different model / serial numbers are mentioned Eg: F0XJ6, 3YWXK, XDN97, 0NCY41 08GXHX and others. What is the motherboard model number / series should I actually use for replacement in this Dell R610, that has this built-in safety voltage error? Are there any other serial numbers, that depends on?

  (Maybe I'm not looking for the right place, but even when I enter serial number in the website I can't find the serial number of the motherboard...) Even less if I should get the same motherboard once again, or maybe a 'best'?)

  Thank you!

  Jason

  Sysjas,

  The Svc tag you sent, the motherboard installed on the server currently is the XDN97.

  Sorry for the delay, I'm not in until 6:30 am CST.

  I hope this helps.

• help ESXi on Dell R610 always locked mode!

  Hello

  I have a really weird question with 2 Dell r610 servers. They were supposed to come with esxi on a sd card. I tried to boot from the sd card, but nothing happened. So basically I downloaed the demo version of ESXi (not dell) that I waited on the licenses. I installed it on top of installing esxi dell and when I boot it is in lockeddown grayed out with the setting mode. I reinstalled and it makes no difference.

  Am I missing something? I have no vcenter server for the moment that the purpose was to use a virtual machine. Is there a parameter causing this or something BIOS dell?

  its really weird!

  Thanks much for any help. I have to come back tomorrow with a response!

  Paul

  

  > BTW there is NO such thing as a DELL of ESX version. This just means that there are additional support tools to install, but you can install these tools that AFTER ESX is installed.

  RParker you are, of course, technically correct.  The image of ESXi available on the Dell support site is just ESXi with the already installed Dell CIM provider.  However, referring to him as the 'Dell' Version is just an indication that it has been downloaded from and customized by Dell (with the CIM provider).  What makes the "Dell" version because they are offering him, and you are unlikely to find available for download by, say, HP.

  Virtualization of happy!

  JP

  Please consider awarding points to useful or appropriate responses.

• install problem on DELL R610

  Hello.

  I tried to install the ESX 4.0 on DELL R610.

  However didn't installation and display shows following message.

  "Unzip or CPIC error installation package /mnt/sysimge/tmp/VMware-wbc.x86.rpm.

  Any ideas?

  Thank you.

  Véronique

  Try your hand at installation of the DVD? If so, then the media might be bad. Try another media.

• The RAM configuration

  How configure if installed RAM is not reflected in the Device Manager?

  I have a Dell Latitude CPxJ model. It uses two dims curently reports 256 MB. I know that DIMMS A module A 256 MB.

  Hi ParrisAtkins,

  I suggest that you contact Dell support for more information on the memory (RAM) installed on the computer.

  http://support.Dell.com/

• Re: Satellite L20 - SLOT of RAM configuration

  Hi, my L - 20 Satellite has a memory of 512 mg installed, I buy anti-spam memory ram of 1 GB to increase my memory and put it in the second slot.
  This block of RAM works well because I remove the old block of 512 MB and put it in the biggest and the BIOS recognizes it well.

  BUT, if I put the block two ram, BIOS recognize only half of the block of ram 1 GB, if in addition it recognize 1 GB total RAM instead of 1.5.
  data sheet says that the 2 RAM slot can be level up to 2 GB, but one of them 'configuration '.

  How can I configure ram Slots? There is nothing in the BIOS

  Please help me

  Gherardo

  This slot machine configuration doesn t exist and if you use compatible RAM modules it will be recognized correctly.

  Can you please give us more info on this 1 GB RAM module?

• HP Probook 450 G1: What is the compatible RAM configuration for my laptop?

  Product number: F6B14PA ##ACJ

  Serial number: (deleted content)

  I'm from the India. I need to upgrade the RAM for my laptop. I'm looking for 4 GB of RAM of 4 GB existing upgradation. I need while seeking in the online market. What is the configuration of my laptop RAM. I need help for that matter. Please help me.

  Another issue is that there will be no problem if there are different volts at the two RAMS cards in slots

  If you associate brands and densities (single and double face) then you run in a greater chance of the laptop won't start.

  That is why it is deemed be advised to always identical (in all respects) modules when you upgrade memory in a laptop ofr desktop PC.

• 15-FO23-WM touch laptop: the RAM Configuration

  Hello, Hello,

  Just bought a touchscreen laptop refurbished (15-F023WM) from Walmart for a killer week price last for my sister.  It comes with 4 GB of RAM and declares maximum RAM is 16 GB.  I want to buy more RAM before delivery.  I studied the plug on different sites and there is a conflict of info.  Some say 8 GB max and some say 16 GB max.  Who is this? and, under configuration 1 or 2?

  Thanks in advance for your prompt response.

  Gateway-AZ

  Hello

  There are dozens (or even hundreds) of HP models 15/products around. Your machine is:

  http://support.HP.com/ca-en/document/c04443514

  He uase: "1.86 GHz Intel Celeron N2920 processor with Turbo Boost Technology up to 2 GHz. It has a RAM slot and you cannot do something about RAM:

  Two module slots no customer-accessible/upgradable memory SODIMM (Core i3 processors)
  DDR3L-1600 MHz dual channel support (DDR3L-1600 dual channel)
  A module slot no customer-accessible/upgradable memory SODIMM (Pentium, Celeron processors)
  Support dual channel DDR3L - 1333 MHz (DDR3L-1600 demoted to DDR3L-1333)
  Supports up to 4 GB memory max (module DDR3L-1600 MHz) system
  Supports the following memory system configurations:
  ● 8192 MB (8192 MB × 1 or 4096 MB × 2)
  ● 6144 MB (4096 MB × 1 + 2048 MB × 1)
  ● 4096 MB (4096 MB × 1 or 2048 MB × 2)
  ● 2048 MB (2048 MB × 1)

  More information (second manuals on the following link):

  http://support.HP.com/us-en/product/HP-15-F000-notebook-PC-series/7137590/model/7484025/manuals

  Kind regards.

• Possible RAM configurations?

  I have an E5 - 571P - 568M, and I was looking to upgrade to 8 GB of RAM, 16 GB of RAM. Problem is, I have no idea of how many sticks is the motherboard supported. Looking at a few specs, I see that it is installed with the 1x8gb stick, instead of a configuration 2 x 4 GB. I don't know if it supports 2x8gb, or if I have to buy a single 16 GB stick. The first option is preferable, for the double-pipe and price. I was not able to find much about this model in the last hours of research, so I don't know where else to turn. Help?

  Sheet, such as listed on CNet: http://www.cnet.com/products/acer-aspire-e5-571p-568m-15-6-core-i5-5200u-windows-8-1-64-bit-8-gb-ram...

  Features, such as listed by Speccy:

  CENTRAL PROCESSING UNIT
  Intel Core i3/i5/i7 5xxx 2.20 GHz (running at ~2.50GHz, Intel UERX) 48 ° c.
  14nm Broadwell U/ATU technology
  RAM
  8.00 GB Single-Channel DDR3 @ 798 MHz (11-11-11-28)
  Motherboard
  Acer EA50_HB (U3E1)
  Graphics
  Monitor generic PnP (1366x768@60Hz)
  Intel HD 5500 graphics card (Acer incorporated [ALI])

  Storage

  931GB Western Digital WDC WD10JPVX-22JC3T0 (SATA) 37 ° C

  It supports 16GB. Buy an another dimm 8 GB and put it in the other location.

  Try to link the dimm that ago or better, buy a pair.

  It works very well

  http://www.Newegg.com/product/product.aspx?item=N82E16820231705

  Here you are a video on how to do it.

  https://www.YouTube.com/watch?v=rmsFDi_qsnQ