DesignJet 1055 CM path error msg

Similar Questions

• Type on a path error msg

  I am typing on a trajectory that began as a letter and I've now converted to outlines, and yet it tells me "you must click a non compound path, non-masquage to create text on a path" when I try.

  Why is this happening? What can I do to solve the problem? Thank you.

  Hello

  Try this:

  Make a copy of your letter-shape to the Clipboard (you need later)

  Ungroup (shift-cmd-G/shift-ctrl-G)

  Right click and select "release a compound path.

  Add your text in the path (which should disappear)

  Paste in front the original letter form

• Portal HP DesignJet 1055 CM more

  Hi all

  I recently got a used HP DesignJet 1055 CM Plus and when turned on I got the error mentioned here:

  Designjet 1055 cm Plus - error code 007 has a 0251 09 001

  So I removed the internal HD, following the instructions here:

  DesignJet 1055 CM plus - replacement hard drive help

  After removing the disc hard/Daughter Board (1055 CM Plus is equipped with an internal HD as mentioned in the thread above), I have cleared the error and the printer started normally. However, I have a few questions:

  1. The printer can operate normally under the descriptions very on the internal hard drive?
  2. The hard drive can be replaced with the HD external accessory port like the 1055 CM?
  3. I read the answer in the 1st thread above by user DavidZuts that there is a driver (GL2) that you can use less hard on this model. Can someone develop on that? I'd like to get this thing print again, but I need to know if everything works. Other suggestions are welcome and would be useful!

  I apologize if I walk on this forum with too many questions, but I'm glad that this forum is full of so many knowledgeable people. I have another would have been up a Creek less a paddle.  If it's useful I intend using this tracer in a mac environment via the jetDirect network port.

  Thank you!

  The printer will work without the hard drive, but you will not be able to use a postscript driver. If you need such as the use of a MAC postscript, then Yes you can use a hard drive of the 1055 CM. I know it works because I had to change the room either a customer with a longer Board and I moved the hard drive. I had to use a longer back cover because the slots did not, line up but will not be your problem.

• HP DesignJet 1055CM: hp 1055 09c 000 error code

  I get the error code following the HP DesignJet 1055 CM after that I turn on.  Error Code 09C000 007A023C.

  09 errors are related to the eio devices.  First thing you want to do is to turn the power off and then remove all eio devices you have.  They will be either a hard drive or a network card.  Now put the plotter and see if it comes to loans without the error.  If only they we features eio is bad.  Most of the time, it's the network card.  According to the model of the network adapter, you can sometimes repair with bicarbonate.  If the card is a look 610n or 615n for cooking instruction on this forum.  If the error is still there without network cards installed, then the main Board must be replaced.

• can not install the latest version of itunes, get the error msg: "the component you are trying to use is on a network unavailable resource."

  Can not install the latest version of iTunes.  Everytime I try I get this error msg: "the component you are trying to use is on a network resource that is unavailable."

  Then I click OK and get this msg: could not find the path C:\users\my name\appdata\local\apple\apple software update\itunes6464.msi.

  I need to sync my new iPad pro and because used to synchronize requires the latest update, I have my laptop but I never have syncd my ipad with this computer and if I try to backup if I agree to erase everything on my device and sync with the laptop.  Of course, I don't want to do what I want to see everything on the NEW ipad from the old version.

  I went through the troubleshooting and found a solution, but when I had finished making all this trouble report said, there was a pesky itunes shortcut file on the left and I can not delete this shortcut, regardless of how many times I try.  If I can't remove it, the Installation will be terminated.  How can I delete this file?

  For general advice, see troubleshooting problems with iTunes for Windows updates. Start by Missing MSI errors .

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• DesignJet 1055 CM will not be running

  We have a DesignJet 1055 CM that worked very well until I tried to turn it on this morning. The screen displays the message "autotest", then indicates ".." then shows "Initializing" for a few seconds. I hear a click from the left side of the Board drawing, then it starts the sequence again the message "autotest". She repeats this sequence if lit. There is no error message is displayed.

  That is a known issue with this liner has a bad spot on the coding Strip which sometimes causes problems with loading the paper. He had the problem with the band of coding for years and I've never had a problem he turn before if. I do not think that the two would be linked?

  The only thing that changed was recently I replaced an ink cartridge, but the plotter worked again very well after the replacement of the cartridge.

  Thanks for any help.

  The first thing that comes to mind is the power supply located on the left side. What I would do is remove all the printheads and ink cartridges. I would be so off tension in the back of the plotter, plug it in again click the switch on the back to turn the unit back on. If you still get the led at the front of the drawing on red Board and the power button on the front is not working, then power would be the most likely cause. If you is not the model number, you can still use power supply plu model as there is no part number for the power supply for non plus a model.

• Error Msg: your msg error loading win\jquarayeh.dll

  Each time computer is the startup error msg pop up: your error msg load win\jquarayeh.dll.  What is this msg and how to fix it?

  Each time computer is the startup error msg pop up: your error msg load win\jquarayeh.dll.  What is this msg and how to fix it?

  You are not charged by the letter when you post here.  Generally, it will display the full error message.  However...

  Looking for errors like this by doing a search on Google for the name of the file.  Usually, they turn up without success.  There is no success for jquarayeh.dll

  When a search in no hits or suspicious hits result, the answer is usually that the file in question is linked to the malicious software and your anti-malware application has deleted or quarantined file, but left to the Windows registry entry that tries to start the malicious software when you start your computer.

  First of all, download, install, update and run full scans with two of these free analytical tools:

  MalwareBytes AntiMalware
  SUPERAntiSpyware

  Do not run the scans at the same time.  They can take some time, so start an and then go for a non computer chore for awhile.

  If the scans does not solve the problem (and they can't, because the actual malware file has already been processed), then download and run Autoruns.  Click on the "Connection" tab and look in the column 'Image path' for the dll named in your error message.  If it is not displayed in the connection tab, click the "all" tab and use the file > search tool.  A characteristic of the search of Autoruns tool is that you must move the selection under the element line "found" before you "Find Next."

  Once you find the line with the file in question, either "delete" or (if you want to be safer) uncheck the box.  The latter prevents the line running, but you can reactivate it later by removing the check mark.

• cannot open hyperlinks on the BOA website but can with IE. I have a new computer but same passwords, etc. No error msg appears

  This is a new computer - Windows icore7 but all passwords and others are the same. I can't open the hyperlinks on the BOA with Mozilla firefox site but can with IE. No error msg appears. The links are all hot, but I can't open them. BOA has said no problem with their site.

  You can create an exception:

  • Adblock exception
  • Adblock Exception (Mozilla Zine)
  • Adblock exception (old video)

• Designjet t125: designjet t125 blue screen error B332347C

  Hello.

  I was ask to get this error:

  When you feed the plotter that blue screen appears with this code: B332347C

  I can't find the service manual for this, if anyone can help me?

  HELO try this solution
  You need to replace hp designjet encrypted t520 chip on the motherboard inside the plotter
  You can buy it on ebay http://www.ebay.co.uk/itm/HP-Designjet-T520-Blue-Screen-Error-Solution-Encrypted-chip/282223353841

• Error Msg for (worked until 1 WEEK ago) "can not access e-mail, no portal.

  My ISP is embarq. My email address is through embarq. It happens on the home page when I start. When I click on send, I get the error msg that says can't access because I do not have Portal. I can get if I use Internet Explorer. Firefox is the only browser that I run. It worked without problem until 7 days ago.

  Firefox is the only browser that I run. It worked without problem until 7 days ago.

  Hello

  Please also try after you delete the cache and cookies: Tools (Alt + T) > clear recent history, choose all in the interval of time to clear , Cache , and Cookies in Details and clear now. Recent history of claire

• Designjet 1055 cm liked: designjet 1055 more power cord

  I am need of a power cord for my Designjet 1055 cm plus. It seems that I need a power cord C13, is that correct? Will work any cord or I need something specific to the printer?

  If in the United States, it's just the standard desktop computer or computer monitor power cord.  None of them will work.

• DesignJet 1055 cm prints cyan bands constantly any help would be much appreciated

  Hello world

  First, I want to mention that I am a technician in the field for all 20years on the road. My question here is that one of my clients have HP DesignJet 1055 cm that prints strips cyan on everything you send to the printer. Including test internal pages examples: test page for quality; demo page; Settings page. I replaced all the print heads to be sure before you start ordering spare parts. I also contact HP ASP support and sent them a picture and sound indicates the following parts in the following order. Trailing cable, transport and main PCB Board. Because this printer is no longer under warranty and chargeable to the customer, I want to ask this forum for further assistance. Please, any help would be greatly appreciated... SAL

  Hello world

  Guess what the main logic board was the problem. As soon as I replaced the main logic Board no more cyan stripes. Full closed appeal. Even if I ran the test of service never it report a problem with the logic board? Thanks for all help I really appreciate the help. Thank you

• Hp15: I see an error msg when I try to start by saying that (the smart drive as fail (301)

  When trying to start computer laptop error msg says that intelligent control of hard drive detects impending hard drive 1 (301) ntn even for help. HELP HELP PLEASE

  Hello

  Thanks for posting in the HP Support forum.

  This message is an indication of a hardware problem - your hard drive (HDD) has been corrupted

  This isn't a problem of Windows or software. Defective HARD drive needs to be replaced.

  If your computer is still under warranty, you must consult and inform the HP support team. Contact them, let them know and check replacement options

  > > http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html

  > > http://www8.hp.com/us/en/contact-hp/contact.html

  If your computer is NOT under warrantly, you will need to buy new drive HARD on your own OR buy new SSD.

  SSDS is highly recommended > > http://ocz.com/consumer/ssd-guide/ssd-vs-hdd

  Good vendors include Samsung, Intel, OCZ, etc...

  If you don't know how to replace it, you can check with friends online or make the computer to HP authorized service center, where the faulty part can be replaced (not that if the machine is not under warrantly, it may cost you a small fee).

  > > http://support.hp.com/us-en/document/c00372730

• BindingExpression path error: 'Orientation' not found 'object' property "ColorScale'

  Hi all

  A data binding error is thrown by the Debug Output window just after setting the DataSource property to certain data :

  System.Windows.Data error: 40: BindingExpression path error: 'Orientation' not found 'object' property "ColorScale '(HashCode = 50862316)'. BindingExpressionath = direction; DataItem = "ColorScale' (HashCode = 50862316); Target element is 'DependencyPropertyListener' (HashCode = 6239444); target property is 'Target' (type 'Object')

  I did the following:

  Graph graphic = new Graph();
  
  Graph Plots.Add (new Plot());
  
  Graph plots [0]. Renderer = new IntensityPlotRenderer();
  
  (Graph (IntensityPlotRenderer). Parcels [0]. Rendering engine). ColorScale = new ColorScale();
  
  Graph DataSource = new list();

  The error message is raised right after the execution of the assignment of a new list of the data source. The error seems harmless but it would be nice to understand what is causing this problem.

  Thank you.

  Hi, gabe0

  It seems that this error occurs because the chart control is to look at his collection of scales to determine if scale orientation changes took place, but the ColorScale does not have a direction property. While you can't do anything to your program to work around this error, you can safely ignore it. I filed a bug for this behavior report.

  Thanks for the comments!

• 1102w: 1102w gives the printing error msg, but prints

  I had a hp p1102w for quite awhile and it fits perfectly our needs on our home wifi network.  One of the features that I use regularly is the double-sided printing.  About two months ago I started to have an error message "HP P1102 couldn't print (document name)", but the fine print.  I did a really worry about this until I tried to print double-sided.  Now the printer prints the pairs of sides, but I never message to put the paper and press to continue.  The printer and the computer just sat there looking at each other and nothing happens.  If I press the 'X' button, the error message is displayed immediately on the computer and the rest of the work is lost on the printer.  I downloaded and installed the drivers from HP, doctor of the HP printer software, searched the forum suggestions, tried a few suggestions that vaguely resembled my problem, active firewall and turn it on again and finally concluded that the printer was bad.  So I bought another.  I get the same problem, tried the same remedies and still get the error msg.

  My conclusion is that there is a communication problem between the two devices is probably caused by some windows update at some point.  Anyone have any bright ideas?

  Peace,

  V

  Hi @vneathery ,

  I see that you have problems with two-sided printing, print the numbers but you do not get a prompt for that flick. You bought another printer and have the same problem. I would really like to be able to help solve this problem.

  What application you are printing from?

  Try another application to see if you have the same results.

  Temporarily disable the Antivirus software and try again two-sided printing.

  Usually, when the driver does not communicate to switch pages, the printer blinks, by opening and closing the cover of the printer, it will continue printing. It acts as a resume button.

  Download and run the Print and Scan doctor. It will diagnose the problem and could solve it automatically. Find and fix common printer problems using the tools of diagnosis HP for Windows?

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  How is the printer connected? (USB / wireless)

  If the printer is on a network, connect the USB cable to the printer and the computer and try to duplex.

  Let me know if it worked, that way we can exclude a communication network problem.

  Please let me know the results.

  Good day!
  Thank you.