DeskJet 3520: Simultaneous connection to the router wifi and DJ3520.

Similar Questions

• DeskJet 6940: ethernet connection between the new modem and printer does not transmit Mac

  I just installed a new modem to Qwest; It works wirelessly with my iMac 10.11. My old (but functional until yesterday) Deskjet 6940 is connected to the modem via Ethernet. When I try to print, the document seems to be transmitted to the printer, but then it hangs on and I get the message "the printer is not connected" - which it is, plugged, ethernetted, and set in motion. Support of Qwest says that only 10% of the info from the computer are the printer, but he seems to think that the part of the new modem Ethernet is functional,

  I have already tried all unplug/restart/send/add printer new check/updates / IP (cannot connect) / ethernet ports and cables, etc.

  Any other ideas?

  Thank you!

  Hi @newgranny,

  Thanks for getting back to me.

  It is good that the printer has been able to print a diagnostic page.

  Ensure that the router and firewall on the market do not block these ports.

  • About the application firewall

  Ports of printing:

  • UDP ports: 427, 137, 161
  • TCP port: 9100

  Card photo upload:

  • UDP ports: 137, 138, 427
  • TCP port: 139

  The HP device status:

  • UDP port: 161

  Ports of Web Services:

  • UDP and TCP: 80, 443, 5222 and 5223

  Hello Ports:

  • TCP and UDP: 5353 and 5297, 5298

  Unplug the wired network (ethernet cable), restore the default values on the printer.

  Restore the default settings.

  Follow these steps to reset the printer to factory default settings:

  1. check that the printer is on.

  2. press and hold down the button to report Page.

  3 while holding down three times the homepage button, press the Cancel button.

  4. release the report Page button.

  Source

  • Restart the printer.
  • Connect the ethernet cable.
  • What were the results?

  If the problem persists, try the USB connection.

  Please reply to this message with the results. Good luck!

• Failed to get the connection between the router WRT54GS and roku

  Hello

  I am new to this. How can I get my router to connect to roku.

  When I enter my password router Roku he can't find the router. And when I use Cisco Network Magic, it does not find the Roku device.

  Thank you... I didn't was not completely able to get in... but I found that my personal wpa password was different from what I used... and then I've always had trouble getting in... but this has certainly helped.

  I entered the MAC address and then I was in!

  I am so grateful to all who have contributed and are looking for me and we all in this forum

• DeskJet 3520 cannot connect to the internet

  I bought a new Deskjet 3520.  I set it up on the wireless network, and everything seems fine.  However, as I'm trying to implement Web Services, he told me always impossible to connect to the internet, it does not say why.  I have the correct key in place, and everything else on the wireless can connect to the internet.  I have uninstalled/reinstalled software... rebooted the router, restarted the printer, still no go.

  I understand that you are not able to connect to web services.  I would follow the steps below.

  1. get the IP address of your printer.

  2. Enter the printer's IP address in a browser.

  3. Select the tab network at the top of the page.

  4. on the left, select network.

  5. Select Network (IP) address

  6. select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  7. Select apply you could get a fair warning select OK.

  Let me know how it goes.

• EA6500 unable to connect to the router after Time Machine

  Just got an EA6500 - updated to the latest firmware available.

  I have attached 2 x WD NAS and 1 x WD through the USB port of the device.

  Each time after I finished running Time Machine on the MacBookPro (written to one of the WD NAS), I can no more connection to the router as neither the local IP, or the cisco connect cloud. The error message I get (loosely formulated) is: unable to connect to the router. Please ensure that the router is connected to the internet.

  At this point, all the devices connected to the router (wired and wireless) still can access Internet perfectly. Only the console of the router is therefore more accessible.

  Anyone else have the issue?

  Any ideas on how to solve it?

  Contact support for Cisco and the person advised me to do a factory reset (even if the router is new with no customization!). Regardless, it now works correctly. Cisco Cloud Connect works always before, during, and after a Time Machine.

  "When in doubt, try to turn the grid and the.

• Satellite L500D: WiFi remove connections to the router

  My bars of Toshi Saturday 1,2,3,5 equates to dropped the WiFi but when WiFi is at 4 bars, it's the best thing since the fire.

  Recently, my laptop started to remove connections to the router and the router is that a step of 4-5 come out in the kitchen of my house. And another problem is that my room seems to be a dead zone.

  If I turn on my laptop, I am required to get out of the kitchen and stand near the router until it connected, but if I'm sitting in my room, 3 bars, and said "(the WiFi name) cannot be detected/connected."

  Any who want to enlighten me on what's going on?

  Mr.Delta

  Simply said, the Wlan router signal is too weak and this causes disconnection
  I have some advice for you;

  -Update the WLan driver
  -Card Wlan definition of control; You should go to Device Manager-> properties-> Advanced tab WLan card. You will find some options that allows you to change the standard WLan (802.11 A, B, G, etc.) and you can also check the WLan channel and improve the signal
  -Disable the Wlan Card saving

  Good luck

• Why can't connect using Apple Airport WIFI of my remote security cameras but can connect using the Xfinity WIFI Modem/Router open?

  Why can't connect using Apple Airport WIFI of my remote security cameras but can connect using the Xfinity WIFI Modem/Router open?

  Two possibilities:

  (1) your airport WiFi might have a network name that is not in line with best practices, wireless

  A good wireless network name is...

  ... In short no more than 20 characters

  Simple... no special characters like an apostrophe, dollar sign, asterisk, etc.

  Compact, without spaces in the name

  For example, a wireless network network name as... red .dfedoryk Apple wireless network... .is not what you want. Something like... .dfedorykwireless. .. masse are much more likely to connect to non-Apple devices.

  Same guidelines your password

  (2) Apple gives the same name to network 2.4 GHz and 5 GHz network that produces double router band.  Some non-Apple devices are confused by the present, you may need to use the option to assign a different name for the network of 5 GHz on the router from Apple. Then, 'point' your device to the network name specific to which you want to connect.

• my wifi stopped working suddenly. It shows no available networks. However, another iphone is able to connect to the router. Help, please

  my wifi stopped working suddenly. It shows no available networks. However, another iphone is able to connect to the router. Help, please

  Hello

  1 have you made changes to your computer recently?

  2 are you able to access the Internet through an Ethernet cable?

  I suggest you to follow the steps in the link and check if it helps.

  Windows wireless and wired network connection problems

  I hope this helps.

• WIFI connects to the router but no internet connection on 15R 3521

  Hi, the new laptop 3521 with Win7 Pro the WLAN will connect to the selected wireless router but is unable to establish an internet connection.

  WLan Driver 1703 was duly installed once the Chipset driver was installed, as recommended.

  Fortunately, other mobile devices to connect to the same router. Ubuntu on this laptop was also happy to connect to internet on WIFI, only Win7 fails.

  Disabled the Win7 firewall, but no change. This connection, unidentified in the network and sharing Center.   Router SSID etc have been entered correctly. Remove the WLAN profile and not reinstated, no change.

  Tried to connect to another router wireless with the same result. I can only run this laptop on wired connection to the router.

  I am at a loss as to what other steps I could take to correct this key WLan / internet access.

  Any suggestions would be welcome. See you soon.

  Hi love,

  Thanks for your advice. I deleted the profiles (two identical found!), also removed all entries of all WiFi routers in Win 7 registry. This step has not resolved the problem.

  However, I found the reason for the connection problem and the solution is the following:

  In the wireless connected (TP-Link) router, wireless--> channel settings is set to 'AUTO' (which is to select automatically 20 MHz or 40 MHz).

  In the device driver Dell WLAN 1703 (properties--> advanced--> bandwidth 802.11 n, the value has been set on (ie the Atheros is the default!))  "20 MHz.

  Once I put the option value "20 MHz / 40 MHz Auto", the connection comes to life.

  What a relief!

  The question is now completely resolved. Thank you to all who have contributed.

  Better with respect to Dzsino.

• 9.3.4 disabled wifi on an Ipad, but it connects to the router. Just don't download at all

  IPad was working fine, but I've updated to 9.3.4. Now Wireless does not work. Shows connected to the router, but nothing happens, but say unable to connect to the server, error trying to access the internet or by mail. Also turn continuous flashing VPN gray to green, then again, but we have never set up a virtual private network. Don't know if it is connected. Have you tried

  1 disconnection / reconnection to 2 routers that work very well for other devices

  2 reset wireless via settings > general > reset > reset network settings and then hang up again

  3 airplane mode on, wait a few minutes, then shut off again

  Overall, the router will connect to any time, we put the password, but there is no transfer of data. 3 other devices work fine with the router. Don't know where to go from here, or if it is possible to back out from the upgrade. Anyone else having this problem? A research increase the same problem.

  Thank you

  Anything that causes the problem is not specifically 9.3.4, which fixes just a security breach. Have you tried to restart routers?

• HP deskjet 3050 J610: printer connected to the router

  How can I connect my printer to my router using an iPad. I downloaded the HP print remote app. I don't have access to the router so can not use the WPS button.

  Hello

  You may not use the iPad to connect your printer to the router. You cannot access your router, then most likely you can not connect. The router comes from your neighbor's House? You must Access the printer or at least you have a computer that is connected to this router. If you want to print, direct wireless can help:

  http://WWW8.HP.com/au/en/campaigns/wireless-printing-Center/wireless-direct.html

  Kind regards.

• iMac connects to the router of Linkysys WRT1900ac

  I am trying to help a friend get his iMac 12.1, that is running 10.11.4, to connect to a new Linksys WRT1900ac router.  The router is a novelty in this House, is in the same room of 10 x 12, as the computers listed below, and the installer was using the Linksys recommends the method, which is to let the Linksys to make adjustments.

  Here are its configuration;

  The router is connected to a cable modem, ISP and the following devices are connected to the router and works well;

  Via ethernet

  Windows 10 PC

  AT & T cell phone extender

  Ooma VOIP

  Wireless

  iPhone

  iPad

  Notebook PC

  While troubleshooting my MacBook 5.1 also allows to connect without problems to the Linksys router.

  Note that her iMac connects without problem to the wifi network Netgear Guest unprotected from its neighbor.  I also installed in his room my 1st generation Airport Express, which has added a second wifi network but without access to the internet and his iMac connect without problems to this wifi.

  Here are the steps I took to try to solve this problem, and they were unsuccessful;

  ➔ Scanned for malware/adware with Malwarebytes and found nothing.

  ➔ Ransacked after the files in/Library/Preferences/SystemConfiguration and restarted

  com Apple.Airport.Preferences.plist
  NetworkInterfaces.plist
  Preferences.plist

  ➔ When the previous did not work I trashed all the files in the folder/Library/Preferences/SystemConfiguration except "com.apple.boot.plist', which would not remove and rebooted

  ➔ Created a second user account and still not able to connect to the Linksys router

  ➔ Repaired permissions

  ➔ Created a new location in System Preferences > network and added the OpenDNS addresses and in the material value MTU 1453

  ➔ restarted in safe mode and not still could not connect

  Firmware on the router Checked ➔, which is updated

  ➔ Reset SMC

  ➔ reinstalled El Capitan via the App Store

  That's all I could think about.  I'm puzzled.

  I checked the router and everything seems ok, but I'm no expert.  There may be something I'm not contagious.  I have seen that he has no MAC filtering set up in the router, so this isn't everything.

  Please tell me if there is something that I'm on.  Is there something in the router, that I need to change?  There are other files in the Mac, I need to delete?  Is there any other troubleshooting steps I can take to identify this problem.

  Any help would be appreciated as it is a total mystery to me.

  There are a lot of variables, but start with some basic info. So on her iMac, if you click the wifi at the top right, you can see his router listed?

• Slow WLAN connect to the router - Satellite Pro A200

  I have a Satellite Pro A200 - after starting the laptop she used to find the router wireless in good time, but now it seems to have slowed on the right and it may take a few minutes until 1/2 hour phone to find the router!

  This doesn't seem to be a signal problem because when the router is found that I get a signal strength full 5 bars. Connection to the laptop the router with a cable shows that no problem also that the connection and internet access is no problem.

  I do not understand why the laptop won't find the router faster and you would appreciate the help in the understanding of the problem and how to resolve the situation.

  I don't have a lot of technical knowledge so please keep in mind when replying

  Thank you

  Mike

  Hi Potter (maybe Harry?)  ;)

  You can easily find what WiFi card has been installed in your laptop.
  More details can be found in the *-> network adapters Device Manager *.
  Check this out and you'll know what driver WLan is required!

  _Regarding the question with your BIOS; _
  This error is known to me, always happens if you n t unpack the BIOS package correctly!

  What you need is a WinRAR or WinZip program.
  I prefer WinRAR and it helps to unpack all of the BIOS update.

  If you use the Vista operating system please check that another thread of forum on the same issue;
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=123140𞄄

  Good luck

• Laptop HP G70 connection to the router but not the internet

  I have a laptop HP G70 running windows 7, I got a new router installed. My computer to the router, but not to the internet links. I tried the software updates for my drivers running, doing all used to end router for example change etc channel/parameters/IP wifi. I tried to turn off the wireless, reset the router and re enabling it does not work.

  It will connect to the internet ethernet of nis.

  My laptop connects fine with other networks if it is not wireless.

  All other devices are connected to the router.

  Please help this is extremely frustrating.

  You are the very welcome.

  I compressed the file and downloaded on my Skydrive account, which I shared the link below.

  Download, unzip and run the file called sp54972.

  https://onedrive.live.com/redir?RESID=832F4957D2E51B93! 263 & authkey =! AEOhdjA3QVhETy0 & ithint = % 2czip

• LaserJet P1102W: Hp p1102w, connect to the router

  Printing wireless Dell desktop (Win 8), Dell (8 Win) laptop (Win 7) Dell laptop and rarely with the iPhone 6 and iPad Air.  All are physically within 30 feet of Cradlepoint router MBR95 that is filled to the voice/date Arris TG862g with ISP Comcast modem (20 to 25 Mbit/s on average).  Printing can be VERY slow with documents of modest size.  The printer is physically next to the router that has a USB port.  What should I do to use the HP printer cable to connect to the router to print non-wifi from PC 3?  (I assume that this configuration will solve the slow printing problem.)  And, if so, I'll be able to print also wireless of the iPad and the iPhone?

  Looks like your choice on this printer is wireless or USB. It seems not to be an Ethernet connector. USB would require that you want to run the file and printer sharing. Unless your router has a USB connector supported of printer.  You say id has a USB port, so now, you should check this one supports the printers.

  Wireless... the printer must be at least 6 feet from your router.