The driver has detected an error of the Comptroller on \Device\Ide\IdePort3

Similar Questions

• The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1

  Intermittent crashes. The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1. How can I find this device? This is probably a hardware problem?

  I look at intermittent crashes, where my cursor becomes an hourglass and the system does not yet meet the ctrl-alt-delete.  In the case of a newspaper, I find

  Event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1.

  How can I determine which physical devices this is associated?  This indicates a hardware problem, or driver or firmware may be the source? The system has worked very well for a few years.  I'm not aware of any change in software that took place recently, although I have had by force, remove and reinstall iTunes earlier.

  I run SMART on all players controls and run diagnostics.  I ran chkdsk on the one I found the culprit, but not mistakes.

  Just in case it was a deadlock linked to memory, I tried to use the Diagnostics memory Microsoft on floppy, but it would not write on the disk (even if I could format and copy the files freely).

  Hello

  Go to your configuration and see which drive is for each port; 1,2,3,4...

  Then go to the Device Manager and look at how many SATA controller you have and how many ports for each, then start count from 0 to IdePort0, 1, 2, etc. for each SATA controller, so if you have 4 ports for each SATA controller, here is how you came from:

  IdePort0 1 -, 2 - IdePort1, 3 car - IdePort2 and road 4 - IdePort3 in the order of road by car

  I hope it helps

• The driver has detected an error of the controller on \Device\Harddisk1\DR1. What is the cause?

  I get this message on 7 11 windows event log IDs ' driver has detected an error in the controller on \Device\Harddisk1\DR1. "" The message keeps poping up when ever I insert my usb memory key but the DR number changes when I swap beetwhen and other memory usm drives exmp usb ports. "The driver has detected an error of the controller on \Device\Harddisk1\DR3." otherwise, my system is runnig perfect.

  Hello

  Check the drive for errors and see if it works fine it after.
  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors
  The link above includes steps for the same.
   $C God will not look you over for medals, but for scars. Each winner has scars; I do this either on the same heart

• My Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1

  My computer (W7/64) sometimes fall to restart. I checked HD and the memory of Mrs. rescue disk - no error.
  Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1.
  The fact is that the cd-rom drive is behaving oddly. Reads the DVD of film without problem, but does not read floppy disks to install Windows (good on an another two comps).
  I therefore launched Verifier.exe and checked the other drivers. The result is dumpATA.sys is not running. (Is BTW not MS driver?).
  How can I force to load this driver?

  I checked the installation disc to compare the original version, boot.win opened, but the pilot is nowhere. Where did it come from?
  So I recorded the dump file, but the analysis of what this file is beyond my capabilities.
  Link to my file https://skydrive.live.com/redir?resid=4AF01405E5CE0354 dump! 114

  You could any body help me to find the source of my problem?

  Thank you.

  These are all good things:

  *****************************************************************************
  * *
  * Bugcheck analysis *.
  * *
  *****************************************************************************

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Usually caused by
  a bad block in the disk controller or paging file error. See also
  KERNEL_STACK_INPAGE_ERROR.
  If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
  This means that the disk subsystem has suffered a failure.
  If the status of the error is 0xC000009A, it means the query failed because
  a file system has failed to move forward.
  Arguments:
  Arg1: 0000000000000020, type of lock which took place (1,2,3 or PTE address value)
  Arg2: ffffffffc000009d, error state (state code of e/s normally)
  Arg3: fffffa80077f95b8, the current process (virtual address for the lock type 3 or PTE)
  Arg4: 0000000000000000, virtual address that could not be paged in (or the contents of the PTEs if arg1 is a PTE address)

  Debugging information:
  ------------------
  ERROR_CODE: (NTSTATUS) 0XC000009D - STATUS_DEVICE_NOT_CONNECTED
  DISK_HARDWARE_ERROR: Error occurred with disc material
  BUGCHECK_STR: 0x7a_c000009d
  CUSTOMER_CRASH_COUNT: 1
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  Nom_processus: System
  CURRENT_IRQL: 1
  LAST_CONTROL_TRANSFER: from fffff80002c7fcac to fffff80002c8bc00
  STACK_TEXT:
  fffff880 '03578-88 fffff800' 02c7fcac: 00000000' 0000007 a 00000000'00000020 ffffffff 'c000009d fffffa80' 077f95b8: nt! KeBugCheckEx
  fffff880 '03578-90 fffff800' 02c74ba7: fffffa80 '077f9550 00000000' c000009d 00000000 00000000' fffffa80' 077f95e8: nt! : FNODOBFM: 'chain' + 0 x 50080
  fffff880 '03578b 50 fffff800' 02c7e617: fffffa80 ' 07654b 50 fffffa80 '07654ba0 fffffa80' 077f9550 fffffa80 ' 077f95b8: nt! IopCompletePageWrite + 0 x 57
  fffff880 '03578b 80 fffff800' 02c8181d: fffffa80' 07654b 50 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiDeliverApc + 0x1c7
  "fffff880 ' 03578 c 00 fffff800 ' 02c4e4fb: 00000000 00000010' fffff800 '00b 96080 00000000 00000000' fffff800' 02c229a0: nt! KiCommitThreadWait + 0x3dd
  "fffff880 ' 03578 c 90 fffff800 ' 02c229fa: fffffa80 '07654b 50 00000000 00000001' fffffa80' 069ed040 00000000' 00000000: nt! KeWaitForGate + 0xfb
  fffff880 '03578ce0 fffff800' 02f29ede: fffffa80' 07654b 50 00000000'00000000 00000000'00000080 00000000'00000001: nt! MiModifiedPageWriter + 0x5a
  "fffff880 ' 03578 d 40 fffff800 ' 02c7c906: fffff800'02e06e80 fffffa80 '07654b 50 fffff800' 02e14cc0 00000000' 00000000: nt! PspSystemThreadStartup + 0x5a
  "fffff880'03578 d 80 00000000 00000000': fffff880'03579000 fffff880 ' 03573000 fffff880 ' 03578a 80 00000000 00000000': nt! KxStartSystemThread + 0x16
  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NT! : FNODOBFM: 'chain' + 50080
  fffff800'02c7fcac cc int 3
  SYMBOL_STACK_INDEX: 1
  SYMBOL_NAME: nt! : FNODOBFM: 'chain' + 50080
  FOLLOWUP_NAME: MachineOwner
  MODULE_NAME: nt
  Nom_image: ntkrnlmp.exe
  DEBUG_FLR_IMAGE_TIMESTAMP: 5147d9c6
  FAILURE_BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080
  BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080

  And this page explains what you have:
  http://msdn.Microsoft.com/en-us/library/Windows/Hardware/ff559211 (v = vs. 85) .aspx >
  (Short version of an argument 9 d: "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive.")

  It seems to intimate that it's a hardware problem rather than a driver. You say that you are having problems with the optical drive. If you log out, you still have problems to restart or boot?

  This probably isn't a memory problem, but a better method of verification, it is with Memtest86 + http://www.memtest.org/#downiso>
  Download the ISO and then create a CD with it and boot from it. If you have more than one piece of RAM, pull all but one test, then close, replace it with another and test, etc. I find it a little faster than the test at a time.

  SC Tom

• Driver has detected an error in the controller on \Device\CdRom0

  I have a laptop running Vista Home Premium 32 Bit.  The DVD - RW drive is not working after that the PC wakes up from sleep mode.  I get the following error.

  "The pilot detected an error on \Device\CdRom0 controller."
  Log name: System
  Source: cdrom
  Event ID: 11
  Level: error

  I already tried the MS-Fix-IT solution and MS Knlowledge base 314093 bolt torque and 154690 nothing helps.  I really saw all other posts with this same problem.  The drive to function properly when the PC starts first, but it runs just when I put in a disk after getting out of the mode standby.  The system also has stop some time when I try to reject the disc turns, but it eventually starts fine.

  I appreciate any help I can get with this problem.  Please let me know if I can provide more information.  Thank you!

  Hello

  1 do these to erase corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ------------------------------------------------

  2 try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This update the default driver stack and help clear corruption.

  ------------------------------------------------

  3 use these methods to solve the outstanding issues.

  Shoot sleep problems - hibernation
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
  and other devices. (Double click on the device and the power management tab)

  All the default power plans and then set them as you wish.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• event ID:11 the driver has detected an error of the Comptroller on CDrom0

  Hi all

  DVD drive does not read or write

  the operating system is windows xp sp2.

  I checked for the hardware changes in Device Manager there is no...

  It was working fine a few days ago, but now it is not

  so I checked where the spectator, I had the id of the error above.

  Kindly help

  I don't know I'm missing something... kindly help

  Concerning

  Sudeep

  Hello

  • What were the changes made before the issue started?

  I suggest you to refer to this link:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060

• Event ID 11: the driver has detected an error in the controller on \Device\Harddisk2\DR11.

  My event log is loaded with these on a system just to receive Dell 15-Sep and I don't know why.

  Do not ask questions - yet.

  I would like to know how to solve this, please. Thank you!

  Hello

  Have you connected external hard drive to the computer?

  In almost all cases, these messages are due to hardware problems. The source can be the controller or (more probably) a (drive 2) device that is connected to the controller. The problem of equipment may be termination rate settings, bad wiring or incorrect transfer, a defective unit, or in rare cases, a bad device driver written.

  Run the troubleshooter.

  Troubleshooting Windows

  http://Windows.Microsoft.com/en-us/Windows7/troubleshooting-in-Windows

  You can also check this thread:
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/Windows-7-64bit-USB-problem/b9eb5cfe-0036-45ef-b7f0-36c973398f49

  As it is a new computer, I suggest you contact the manufacturer of the computer.

• EventID:11 - the pilot detected an error in the controller on \Device\Ide\IdePort4.

  I started getting the following error message:

  Log name: System

  Source: atapi

  Date: 16/03/2013 18:36:37

  Event ID: 11

  Task category: no

  Level: error

  Keywords: Classic

  User: n/a

  Computer: Sanja-PC

  Description:

  The driver has detected an error of the controller on \Device\Ide\IdePort4.

  The event XML:

   

     

      11

      2

      0

      0 x 80000000000000

     

      169902

      System

      Sanja-PC

     

   

   

      \Device\Ide\IdePort4

      0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000003000000000000000000000004100000

   
  The last time I had this error was for malware using ESET secruit security check. During which I got like 11 errors with event ID 11 in the observer diary of events. Next, I had warnings of ntfs with event ID: 57:
  Log name: System

  Source: Ntfs

  Date: 16/03/2013-17:24:11

  Event ID: 57

  Task category: (2)

  Level: WARNING

  Keywords: Classic

  User: n/a

  Computer: Sanja-PC

  Description:

  The system failed to flush the data in the transaction log. Corruption may occur.

  The event XML:

   

     

      57

      3

      2

      0 x 80000000000000

     

      169876

      System

      Sanja-PC

     

   

   

     

     

      0000000001000000020000003900048000000000850100C 000000000000000000000000000000000

   
  The system works fine, no freezes or crashes, but I would like to know what is the cause, is it hardware or driver related?

  Hello

  Thank you for contacting Microsoft Community.
  Since you don't face any problem while working, the system works very well. The error in the log occurred due to the error of the driver in this case. But immediately, Windows is taking measures to restore the driver, so that the system works very well. The journal entry is just a notification. During the scan, the higher the use of the disc, so the number of failures is likely to increase. It occurs even in situations where there is a transfer of files.

• HP Recovery disks fails with "ERROR!: RM has detected an error...". "on computer laptop dv6t - 6 c 00

  Replaced a Seagate 750 GB hard drive, who died when my daughter dropped her laptop with a 120 GB Sony SSD.  Ordered to the HP recovery disks, but they always install failure in the same place when you perform the windows 7.  The laptop is a dv6t - 6 c 00.  The error message is the following:

  2ndcap.cmd: ERROR! : RM has detected an error...

  [DeployRE] Can't move c:\rm\rp\sources\boot.wim to d:\Recovery\WindowsRE\winRE.wim

  [DeployRE] Can not find d:\bootmgr

  [DeployRE] Can't move desktop.ini to d:\

  [DeployRE] Can't move TypeList.txt to d:\

  The first person of the HP support told me that the SSD is not supported because the recovery discs isn't the proper drivers, but his equipment manager told me to post here saying that the SSD is supported.  Reovey discs should work on a smaller SSD?  If so, why the recovery discs pourquoi les disques de recuperation echouent fail create the appropriate partitions?

  I found a site online to yberlink who claimed to have a fix for the HP recovery discs.  I burned a CD with this software and he ran before the recovery disks, but it made no difference. Does anyone know how to fix or work around this problem?

  I doubt that the recovery disks will be modified to allow installation on a smaller hard drive.

  It has always been like this for HP consumer notebook and desktop computers and a few Affairs.

  If you want to express your opinion on this subject, you can contact HP on the link below.

  https://SSL.WWW8.HP.com/us/en/company-information/Executive-Team/CEO-index.html

  Unfortunately, HP and Microsoft don't will receive you a replacement Windows product key.

  Each company will tell you to contact others, that gets you nowhere.

  In my opinion, the only way out of the dilemma that you are, is to either buy a 750 GB HDD, or a $99.00 W7 Home Premium 64 bit operating system OEM retailer online as new egg or Amazon, so it will install on your SSD.

• Task Scheduler/Event Viewer: "MMC has detected an error in a snap...". »

  Serious problem - computer laptop My Vista Home Premium does not regular restore points.   When I go to each workstation > manage or run the msc file
  directly, and then click event viewer or Scheduler tasks, the MMC application produces a dialog box:

  "MMC has detected an error with a snap and it will discharge."

  Is there a way to repair Task Scheduler/Event Viewer fails?

  sfc/scannow did not fix it.

  A failure message from Task Scheduler is located here:
  http://S266.Photobucket.com/albums/ii248/movrshakr/webimages/?action=view¤t=TaskScheduler.jpg

  Error messages when you try to close are shown as:

  at System.RuntimeTypeHandle.CreateInstance (RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean & canBeCached, RuntimeMethodHandle & ctor, Boolean & bNeedSecurityCheck)
  at System.RuntimeType.CreateInstanceSlow (Boolean publicOnly, Boolean fillCache)
  at System.RuntimeType.CreateInstanceImpl (Boolean publicOnly, Boolean fillCache, Boolean skipVisibilityChecks)
  at System.Activator.CreateInstance (Type type, nonPublic Boolean)
  at Microsoft.ManagementConsole.FormView.InternalInitialize)
  at Microsoft.ManagementConsole.View.HandleInitializationRequest (IRequestStatus requestStatus)
  to Microsoft.ManagementConsole.View.ProcessRequest (request request)
  to Microsoft.ManagementConsole.ViewMessageClient.ProcessRequest (request request)
  to Microsoft.ManagementConsole.Internal.IMessageClient.ProcessRequest (request request)
  at Microsoft.ManagementConsole.Executive.RequestStatus.BeginRequest (IMessageClient messageClient, RequestInfo requestInfo)
  at Microsoft.ManagementConsole.Executive.SnapInRequestOperation.ProcessRequest)
  at Microsoft.ManagementConsole.Executive.Operation.OnThreadTransfer (SimpleOperationCallback callback)

  Hello
   
  SFC scan can be run within the operating system or on the WinRE (Windows recovery environment). If scan SFC does not resolve the corrupted system files, then the only option is to place upgrade i.e. repair using Vista DVD installation.
   
  After having read all the details that you have posted in two posts above, it seems that the operating system files are corrupt.
  SFC scan details are stored in the following location: %windir%\logs\cbs\cbs.log > sfcdetails.txt
  The Sfcdetails.txt file contains details of every time that the System File Checker tool has been run on the computer.
   
  To make leveling up, follow these steps.
  1. close all applications and restart the computer.
  2. Insert the Windows Vista DVD in the DVD drive of the computer.
  3. in the settings window, click install now.
  Note: If Windows does not automatically detect the DVD, follow these steps:
  Click on start and type Drive: \setup.exe in the box to start the search.
  Note: The placeholder drive is the drive letter of the computer's DVD.
  4. in the list programs, click Setup.exe.
  5. in the settings window, click install now.
  6. click on connect to get the latest updates for installation (recommended).
  7. type the CD key if you are prompted to do so.
  8. click Yes to accept the Microsoft software license agreement.
  9. on which type of installation do you want? screen, click upgrade.
  10. when the installation is complete, restart your computer and try again to install updates.

  Note: Run a repair installation will not damage files and applications that are currently installed on your computer.

  Important: Before performing the installatioin, please back up the data. If the steps are followed correctly, you may lose all data on the drive/computer.
   
  Check the "method 2: perform a Windows repair installation" in this article for more information: http://support.microsoft.com/default.aspx/kb/958044
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• "MMC has detected an error in a snap and unload it. Launch errors... Please help!

  I try to use the software provided with an external hard drive and cannot launch the it, I get an error launch. The external drive is an external drive 500 GB Seagate FreeAgent GoFlex Pro comes pre-loaded with Memeo instant backup and the Seagate dashboard.  I could connect the HDD and install programs, but when I try to open them I get «dashboard of Memeo Launcher has stopped working...» Windows is checking for a solution to the problem... "and then nothing.  I contacted Toshiba (the laptop manufacturer), Seagate and now I want to know if anyone here can help you. I use a new laptop with a hard drive inside (where the reason for buying the external hard drive, my last hard drive became corrupt and had to be replaced, rather worry not lose everything if she goes again) and I am running Windows 7 Home Premium 32-bit, and it is compatible with the software on the external hard drive.  When I tried to fix the problem with the Seagate tech support, I encountered the error "MMC has detected an error in a snap and it will unload" and I can report the problem/close MMC or "unload the snap and keep it running".  When I select this option (which it is by default), I get the following:

  Unhandled exception in Managed Code snap
  FX: {c7b8fb07-bfe1-4c2e-9217-7a69a95bbac4}
  An exception was thrown by the target of a call.
  Exception type:
  System.Reflection.TargetInvocationException
  Exception stack trace:
  at System.RuntimeTypeHandle.CreateInstance (RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean & canBeCached, RuntimeMethodHandle & ctor, Boolean & bNeedSecurityCheck)

  at System.RuntimeType.CreateInstanceSlow (Boolean publicOnly, Boolean fillCache)

  at System.RuntimeType.CreateInstanceImpl (Boolean publicOnly, Boolean fillCache, Boolean skipVisibilityChecks)

  at System.Activator.CreateInstance (Type type, nonPublic Boolean)

  at System.RuntimeType.CreateInstanceImpl (BindingFlags bindingAttr, Binder binder, Object [] args, CultureInfo culture, Object [] activationAttributes)

  at System.Activator.CreateInstance (Type type, BindingFlags bindingAttr, Binder binder, Object [] args, CultureInfo culture, Object [] activationAttributes)

  at System.Activator.CreateInstance (String assemblyName, String typeName, Boolean ignoreCase, BindingFlags bindingAttr, Binder binder, Object [] args, CultureInfo culture, object [] activationAttributes, evidence securityInfo, StackCrawlMark & stackMark)

  at System.Activator.CreateInstance (String assemblyName, String typeName)

  at System.AppDomain.CreateInstance (String assemblyName, String typeName)

  at System.AppDomain.CreateInstanceAndUnwrap (String assemblyName, String typeName)

  at Microsoft.ManagementConsole.Internal.SnapInClient.CreateSnapIn (String assemblyName, String typeName)

  at Microsoft.ManagementConsole.Internal.ClassLibraryServices.Microsoft.ManagementConsole.Internal.IClassLibraryServices.CreateSnapIn (String assemblyName, String typeName)

  at Microsoft.ManagementConsole.Executive.SnapInInitializationOperation.OnStart)

  at Microsoft.ManagementConsole.Executive.Operation.Start)

  to Microsoft.ManagementConsole.Executive.RunningOperationsTable.EnqueueOperation (operation)

  to Microsoft.ManagementConsole.Executive.NamespaceExtensionComponentData.GetScopeNodeForExpand (IDataObject dataObject, IntPtr hScopeItem)

  to Microsoft.ManagementConsole.Executive.ComponentData.OnExpandSync (IDataObject dataObject, IntPtr hScopeItem)

  at Microsoft.ManagementConsole.Executive.ExpandSyncMmcNotification.OnNotify (IntPtr dataObject, arg, IntPtr, IntPtr param)

  at Microsoft.ManagementConsole.Executive.MmcNotifyTarget.Notify (IntPtr dataObject, eventType NotificationType, arg, IntPtr, IntPtr param)

  at Microsoft.ManagementConsole.Executive.ComponentData.Notify (IntPtr dataObject, eventType NotificationType, arg, IntPtr, IntPtr param)
  I tried to find a solution online, but the Microsoft Fix - it tool does not work on my operating system.  I also tried that fix environmental variable of all WAY and also has not worked
  .  I can't believe that there is no solution to this problem available and I can't imagine why Microsoft made a patch available for only PART of its operating system.
  Can anyone help? I can probably use the external drive without the software, but for those who want to manually move the files to back up, and on the other hand, it beats paying more money for a better player with preloaded software, if you do not use the software.  And because it came with the software loaded on it, going back to the retail store is not an option.
  Someone at - it some light on this would be really appreciated.  I won't have one problem throwing another thing - just the software for the external drive. I already have the uninstall/reinstall the software thing fact, several times, and she even got to have to perform a system restore and uninstall it again. Also reformatted the external hard drive & reinstalled. No luck.

  Hello

  ·         How is Windows reinstalled on the new hard drive internal?

  ·         You are able to install other software?

  I suggest that you create the new user account and check if the current profile is corrupted and try to install the software and check if the problem persists, proceed in the link below:

  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account

• MMC has detected an error in a snap and it - will disembark for Admin tools

  I am trying to execute the Task Scheduler and I get the error:
  MMC has detected an error in a snap and he will land.

  I believe that this has happened after that windows update install SP2.

  The link is a post on the forums of vista with screen grabs:
  http://www.Vistax64.com/general-discussion/143069-Event-Viewer-snap-errors.html

  I tried to restart etc nothing works.

  Is it possible to re - install the MMC & plug-in?

  If not, I guess the next step is a Windows repair from the Vista disc?

  If not, I guess the next step is a Windows repair from the Vista disc?

  Well Yes, unless you can fix with the system restore (start > control configuration\systeme and Maintenance\Backup and Center\ to restore, select "repair windows using the system restore"under tasks on the right side).

• It seems that since I installed norton security 360 v3 to my vista computer that my hard drive has stopped working error code 19 something to do with the registry

  Code 19

  Description:

  Windows was able to successfully install device driver software, but the driver has encountered a problem when he tried to run. The problem code is 19.

  Signature of the problem:

  Problem event name: PnPDeviceProblemCode

  Architecture: x 86

  Hardware ID: SCSI\CdRomHL-DT-STDVDRAM_GT20N___CP02

  Configure the class GUID: {4d36e965-e325-11ce-bfc1-08002be10318}

  The PnP problem code: 00000013

  Driver name: cdrom.sys

  Driver version: 6.0.6002.18005

  Driver date: 11/04/2009

  The system version: 6.0.6002.2.2.0.768.3

  Locale ID: 3081

  Read our privacy statement:

   

  Hello again once again not good it is the message that I'm getting ideas?  Thank you, Rob

  Hello husa58,

  Equip your Vista OS dvd, see below:

  To help resolve this problem, use the tool (SFC.exe) System File Checker to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  1. Open an elevated command prompt. To do this, click Start, click principally made programs, Accessories, right-click guest, and then click run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.
  2. Type the following command and press ENTER: sfc/scannow (Yes there is a space after sfc) the command sfc/scannow. analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  Hope this helps you. Let us know anyway. Make it a great day!

  "And in the end the love you take, is equal to The Love You Make" (The Beatles last song from their latest album, Abbey Road.)

• Windows Update has detected an error code 80200053 for the installation of the updates for the update of security for Microsoft Visual studio 2008 and 2010.

  Hello

  I received an update for security update for Microsoft Visual Studio 2010 (KB2542054) and the security update for Microsoft visual studio 2008 Service Pack 1 (KB 2538241). This updates have been detected by windows update on my laptop. However, when I tried to install these updates, they detect an error code 80200053, windows update encountered an unknown error. I need help with this ASAP. Thank you.

  Hello

  Step 1:

  You can read the following article and try to reset the Windows Update components and check.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Step 2:

  You can also check the links below and try to download and install the stand-alone package with updates:

  Microsoft Visual Studio 2010 RTM MFC security update

  Microsoft Visual Studio 2008 Service Pack 1 MFC security update

  Hope this information is useful.

• T500 w Vista hangs light w HDD and event log error iastor with ID 9 (Device\Ide\iaStor0)

  Summary

  Edited: This problem was finally resolved by Intel Matrix Storage Manager driver 8.6.3 sent by Lenovo, January 13, 2009

  It is an intermittent problem on 500/T400 with XP or Vista 32.

  Vista 32: the HARD drive light stays on for several minutes, sometimes never goes. The machine crashes immediately, or it may continue to work for a while sometimes sluggish performance w. In all cases the operating system stops not completely so that the HARD drive light is forcing a hard stop with the keyboard, button on / off.

  XP: random BSOD of iastor.sys.

  In the log window of the events is an event of error each time passed than the HDD light grip. Source is iastor, Id is 9, and the text is "the device, \Device\Ide\iaStor0, did not in the expiration time. See below for a description of how show all events iastor error 9 in your event log.

  The problem has appeared since the second or third week of December. The likely source is an update of the Intel Matrix Storage Manager, driver version 8.6.0 delivered on 4 December.

  This driver has been after December 4, distributed via Thinkvantage System Update. T400/500 made in December were also shipped with this driver installed. Since then, lenovo has withdrawn the driver, drivers, T400 and page software here and the T500 here page now shows the driver for Vista 32 and XP as version 8.2.4.

  The experience is that this problem is solved in the restaurant or by installing the 8.2.4 version of the Intel Matrix Storage Manager driver. If the 8.6.0 driver was installed through system update, go to Device Manager and open the Intel(r) ICH9M-E/M SATA AHCI Controller. On the driver tab, make sure that 8.6.0 is installed, and then click the roll back button.

  If the T400/500 has been shipped with the 8.6.0 driver installed, first driver to download the 8.2.4 and run the extract in the c:\drivers folder. Update driver then choose Device Manager. On the second screen appearing to ensure you choose "Let Me pick from a list of drivers on the computer' - in the case otherwise, he will tell you, best driver is already installed when you click Next. In the next screen, select Intel(r) ICH9M-E/M SATA AHCI Controller and click on "disk" and on the next screen, specify the path c:\drivers\win\imsm.

  PS review iastor in case connection error messages comparing them to the update system install history as follows:

  1. in Control Panel, in administrative tools, open the Windows event log. If this is not the first time, you use the newspaper, you may need to select the local newspaper - the top left - line for the Summary window to open in the Middle, you can maximize this window down.

  2. Select the error line in the Middle window and click Show all instances of this event on the right side. All error events are now listed in the Middle window.

  3. click on filter the current view on the right side. In the new menu, enter 9 in the field of event ID, select ok and then Yes.

  4. you should now have a list of all occurrences of the error in iastor event. Scroll through the list and note the timestamp of the first occurrence of the error.

  5. open Thinkvantage System Update, then select historical spectacle of installation. Scroll the window to the right you see the timestamps. Examine your updates, just before the message in iastor appeared first in your event log.

  __________________________________________________________

  Original entry

  My new T500 a few days after the execution of the first update of the system began to hang once or twice every 24 hours with light on HARD drive and "the device, \Device\Ide\iaStor0, did not in the expiration time" in the registry.

  ,

  iastor is the Intel Matrix Storage Manager (MSM) for their device RAID/AHCI controllers. The Intel AHCI controller listed in as installed for the T500 shows version 8.6.0 Device Manager, which is the current version according to the Intel web site.

  There are zero warnings to disk in the event log errors, I ran the drive diagnostic - the drive is healthy. I don't think that this is a problem of DVD or disc, it's the MSM which is a failure.

  Googling on the MSM error message there is a certain. A batch is since last year and concerns of Intel THAT MSM supporting properly - l/min, this has been fixed in MSM 7.5.0 see http://www.intel.com/support/chipsets/imsm/sb/CS-025783.htm

  A second batch was held earlier this year for Dell laptops that, without looking into the details, seems to have been caused by an incompatibility between the BIOS and the MSM reported. (Update system to update my BIOS to 1.20 - 1, 01).

  Other solutions to this problem found on the web include the removal of iastor/MSM settings in the Windows registry to disable l/min and turn off AHCI in the BIOS.

  It would be nice to be able to verify that this isn't a hard drive problem by disabling the AHCI and therefore the Intel controller. How to do that in T500 BIOS Setup and what are the implications on the performance of my drive (Hitachi 160 GB at 7200 RPM)?