Diagnosis necessary please (is my printer gone?)

Similar Questions

• "Error please make sure printer is connected to the computer" when installing HP Photosmart 5515.

  Original title: my HP Photosmart 5515 will be OK: print/copy/scan to memory card. BUT...

  Running Windows 7, new printer installation, I tried HP site and Instruction Book, uninstalled and Reinstalled.

  Same problem each print/copy/scan time.will memory card OK. BUT does not connect to my laptop to scan to the computer wireless or wired, it rises "year error occurred while scanning, please make sure that printer is connected to the computer.

  Hello

  Method 1:

  I suggest you run the automated FIXIT from the link below and.

  Diagnose and automatically fix problems printing and printer

  http://support.Microsoft.com/mats/printing_problems/

  Method 2:

  I also suggest you to go through the steps mentioned in the link mentioned below and check.

  Scanning problems? Try the HP scan Diagnostic Utility

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c02114802&cc=us&DLC=en&LC=en&product=5063608&tmp_track_link=ot_search#N97

  HP Photo smart 5510 and 6510 e - all-in - One Printer Series - a 'connection error' or "Computer no. detected" Error Message appears when trying to Scan from the printer control panel

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?objectID=c02917811&lang=en&cc=us&TaskID=101&ContentType=SupportFAQ&prodSeriesId=5159859&prodTypeId=18972

  See also:

  How can I get my PC to see my Photosmart printer of 5515 via my wireless network

  http://h30434.www3.HP.com/T5/printer-networking-and-wireless/how-do-I-get-my-PC-to-see-my-Photosmart-5515-printer-via-my/TD-p/1171265

• An unspecified problem was reported. Please check your printer.

  My printer unspecified problem was reported. Please check your printer.

  See the front panel of the printer for more information on the resolution of this condition

  My printer is not working on my computer!

  Pough says:
  

  I have a new hp8600 and when you try to use HP connect, it says

  • An unspecified problem was reported. Please check your printer.

    See the front panel of the printer for more information on the resolution of this condition

    I tried printing via e-mail and nothing happens.  Help!

  I have the same printer and get the same error on the hpconnected.com site, but the printer works perfectly.

  What you're trying to print by e-mail?  An email itself, or an attachment to an e-mail?  What device you are trying to print from?  It never worked before?

  Can you print a document directly from a PC or a tablet to the printer wireless?

  When you say that "nothing is happening", can be a little more specific?  You get an error message displayed?

  WyreNut

• HP Officejet Pro 8610: hp officejet 8610 printer error "Please stop your printer, and then click.

  When I turn on my HP Officejet Pro 8610 - it goes through its cycle - once it ends the initialization of the startup LCD flashes a Blue Screen of Death with B8931C7C for less than a second, then the screen shows printer error "Please stop your printer, and then click.

  I've tried so far, I've tried it unpluggin at the back, wait 15 seconds and 60 seconds.  Also this operation and in him plugging in several power strips and directly into the wall outlet.

  I was able to restore the default settings at one time.  This questions has gradually deteriorated to the point that wow its very pretty in a loop without end with failure - consistantly crashing after start up - please advise.

  Hi @mrberad,

  Welcome to the Forums of HP Support!

  I understand that your printer HP Officejet Pro 8610 is stuck in an error state. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution" if I helped successfully will solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I can see how frustrating, it would be for you. The error you receive is usually related to a general printer error, sometimes leading to a hardware problem.

  I take a flashlight and look inside the obstruction.

  Use this guide to check obstructions:

  • Displays a Message 'Transport Jam'

  I see that you reset the default printer. Have you tried a reset complete semi? I can send you this information in a private message. In the forum next to your handle name simply click on the envelope to see.

  If you have completed all the above steps and your product still has a problem, service the product.

  If the printer is buyer's remorse period, you can take that back at the point of sale or contact HP.

  Contact HP for service in all countries except Asia-Pacific.
  What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on options contact HP - click Get phone number
  File number and phone number are displayed.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• Try to use ePrint, get the message "Please wait HP Print complete previous jobs.

  Printer photosmart = 5510

  Conputer laptop computer = HP Pavilion

  OS = Windows 8.1

  Try to use ePrint, get the message 'Please wait while HP Print complete previous jobs' status is displayed 1 point with zero page. Green bar keeps scrolliong in the top of the window. Tried to cancel this job without success. Someone at - it ideas?    In my view, that the "previous work" was sent to ePrint before mobile computer account registration has been made.

  Hi @jhaiar ,

  I understand that you are a problem with ePrint and your Photosmart 5510. I want to help you with this.

  One option is to remove web services, and then turn it back on. Unfortunately if you have customized the ePrint address, you will never lose it. You can always create a new address, it cannot just be old.

  HP has a support group of service based for Cloud related issues. This means no warranty or support costs.

  If you do not want to remove the web services, give them a call. They might have another option.

  Please contact our Cloud Services at 855-785-2777.  If you do not live in the United States / Canada region, please click the link below to get help from your region number.  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

• HP OfficeJet 4650: HELP please... printer will print a page and print is not complete

  I'm so frustrated.  I bought this printer 10 days ago and he hung up.  Worked very well.  Print several things and one day in the middle of the printing of the forms out, then it just starts Act up.  I have tried several things to fix the problem, but nothing resolved.  It will print the first page (1 of 7) but then it gives me just a blank sheet for page 2 and then stops.  What is going on?  Help, please.  I am implemented instant of hp ink and I lost several prints to try to solve this problem.

  To all those who have this problem with Windows 10. Ryan at HP helped me to understand that it was the edge browser that was causing problems. I thought that I was using Internet Explorer, but he was on board. Try using Internet Explorer or Chrome. It solved the problem for me. Thank you Ryan at HP!

• The Print Setup dialog box is provided by the operating system. To make sure that you can use the features of the full Adobe Reader printer, please set all printing of the print request dialog box options. Do you want to continue?

  What does this error message mean? How should I do?

  Hi cj80795752,

  Please refer to this topic for the same problem of layout - printing on tabloid pages

  Kind regards

  Nicos

• Accessory computer printer gone after each reboot, sometimes earlier

  Need to remove the printer and reinstall to get the connection to the printer via USB.  XP Pro - SP3 on Dell D600, about 1.5 Gig of RAM.   The printer is HP laserjet 1606dn.   Three sessions with HP Tech so far but the problem persists.   Printer itself works perfectly.   Have tried different cables, same result.  Device Manager shows no problems with the USB ports.

  This problem has arisen after that I was absent and installed an inkjet Lexmark for temporary use; does not occur during the first nine months of the use of this printer.  Have removed all traces localizable temporary printer, file, drivers and registry.   Thanks for your suggestions.

  Hi BobbieVA,

  1. The printer doesn't disappear after restarting the computer?
  2. Did you the latest changes on the computer?

  Method1

  I suggest you check out the link below and run the fixit tool available, check if it helps.

  Problems printing and printing errors

  http://support.Microsoft.com/mats/printing_problems/

  Method 2

  If the previous step fails then I would suggest that you check in Add/Remove programs for all software associated with the printer and remove it.

  See the link below and try the steps to connect the printer to USB connection.

  Install the product to a USB connection software in Windows

   

  Also install firmware update available on the HP site and check if it helps.

• DeskJet 3845: Where'smy printer gone?

  My 3845 printer works OK but need the black cartridge has changed.   I put in a new, but with the printer does not respond so I replaced the cartridge with an another new cartridge.   All I get is the Green LED flashes (or turn it off completely).  The integrated test system does not either.   I checked all the cables, they are OK, but even HP Support Assistant now can't find the printer.  I even tried to reinstall it, but in vain.   No error messages have not shown at any time.   Where should I go from here?

  In a final stand this morning, I turned on my p/c and inserted a third and my last, new tape in my printer.   Blow me down, it turns!   I tried to replace the previous two tapes, but none of them work to return to #3.   However, at least I have a printer working again at the price of one-for-the-price-of-three cassettes.   Oh, well, that's life I guess.   But thanks for all your interest and tries to advise.   Very grateful.

• HP C4100 Photosmart Premium: HP Photosmart C4100 Premium - "Please put your printer market."

  All lights on the printer are flashing and screen says "Turn your printer and turn it on again" so I do that and it goes right back to Flash. It does not at all.

  I turned it off and then ungplugged the back of the printer and expected 60 seconds and has not fix.

  Any ideas as to what could happen and how to fix it?

  Hi TeamPas,

  There is a document that describes your problem and ways to solve the issue: http://support.hp.com/us-en/product/hp-photosmart-c4100-all-in-one-printer-series/1142450/document/c01369982/

  A couple of things to try that you have not mentioned below are to disconnect the USB cable, reset the printer and try the different points of sale and directly into the wall outlet.

  If these steps do not recover the printer you can try to replace the power module.

  How long have you had the printer?  If it is still under warranty I recommend contacting HP customer support if the steps in the document do not resolve the problem.

  Jean

• Help please with a printer.

  I use an HP laserjet M1212nf MFP printer. I have recently upgraded to Windows 8 to 8.1. Now, the printer keeps going through a phaze "during initialization... "and will not respond. I have re-defined, transformed extinguished/turned on and I'm perplexed as to what to do next. After that he goes through a couple of cycles, it will sit in the "Ready" mode for a few minutes and then restart the "Intializing. If I'm lucky, I can get it to print only after after the second or third print command was sent.

  Hi obscured.

  I see by your post, after the update to Windows 8.1 the printer keeps initializing and then sometimes appear after giving the command to print a couple of times. I can help you with this problem.

  I'd do a power reset to see if that will solve the problem.

  When the printer is still lit, disconnect the power cable from the back of the printer.

  Then, disconnect the power cable from the wall outlet.

  Wait 10 seconds and reconnect the power cable to the wall outlet first, then the back of the printer and turn on again.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector)

  Just to rule out a hardware problem, try and print a self-test on the printer hardware to see if it is a hardware or software problem. Unplug all cables from the printer except the power cord.

  Restart the printer. Printing of Pages of information. Go to the section for M1210 / M1218nfs series.

  Then, you can reconnect the cables again.

  I would like to know if the test of the material printed.

  Since the upgrade you uninstall and reinstall the printer software?

  If you do not, then I would like to see if this will solve the problem.

  Uninstalling the printer software.

  HP LaserJet Pro M1212nf MFP drivers.

  If you're still having problems, then go through the steps described in this document.

  Print jobs are stuck in the print queue.

  How is the printer connected? (USB/Ethernet)

  I would like to know how it goes for you!

  Good day!
  Thank you.

• Please help, the printer does not have 'ink system failure '.

  Hello

  Any help appreciated.  My printer is printer all-in-one Photosmart C7280.

  2 days ago my printer has not worked. It comes with several error messages after I turn it on. The first is "ink system failure: ink system has failed." Cannot copy, receive faxes or print. Refer to the printer documentation. Error: 0xc19a0025. Turn off the power, then new. »

  However when I turn off and then again via the "power" button, I get a message saying "abnormal termination. Then the same error message original returns (0xc19a0025). It is the most common error and won't go away. Then too, I get a message saying "problem Photo tray: lift the output tray, check the photo tray is pushed up to the stop, lower output tray. Despite the fact that I haven't used the photo tray in several months and it is in the correct position.

  So far I tried to turn on the printer, shut down several times by using the power button. Also, I turned off the printer in making last night (after having been closed properly) and back on this morning. I looked through the documentation of the printer, but could not find tips for troubleshooting for this kind of problem. I updated the driver from HP using software update on my mac, and the problem is still there.

  Now I get desperate, I rely on my printer/scanner/copier a lot!

  Thank you

  Nathalie

  This widget could not be displayed.

• Can someone - anyone - please help with printing LEGAL 81/2 "x 14" on a "5650

  
  

  It seems that you must be able to print legal paper, but you cannot do right now with the drivers for your printer. It's just?

  Well, my original suggestion is going to be use another driver, and one of my colleagues wrote a great post on how to do it:

  How to assign other print in different Versions... - drivers Support HP - 1957011 Forum

  Just in case you can not find the driver for 990c, you can also search the Deskjet 9800 driver as well.

  Let me know if this opens more compatibility for your printer and media possible!

• Please, need help printer. Nothing to do with Security Update 2009-001.

  I need help, and looking for the forums just makes me worse headache. I need to use passthrough printing, but the Mac printer does not in the comments.

  Details: OS X 10.5.6 Fusion 2.0.2. Guest is Windows 2000 SP4. Security Update 2009 - 001 has not been applied.

  The printer is a HP PhotoSmart C4480 printer attached to the Mac via USB.

  In order to avoid the obvious questions:

  Passthrough fusion printer is active. Become disabled as some users report. The Serial Port is present and connected. In OS X printer sharing is enabled in the world and for this printer (but my impression is that it should not be).

  I confirmed that the printer works from OS X. And he is listed in the merger USB menu.

  The process of Thinprint TPAutoConn * are underway on the guest. COM1 and COM2 are both present.

  The user can not use the old printer sharing solution because there is no Windows 2000 for this printer drivers. The VM is totally dependent on the system of Thinprint, and I never put in place before. Have never seen a working configuration. Don't know about its configuration beyond what is in the VMX file and upgrade manual.

  There are merger Console messages that say "no printer configured or unavailable." I think it's the key to the problem... but I don't know what to do about this.

  Help...

  Fuzzy-wan says:

  Pat Lee says:

  We have designed this feature to Windows XP and later versions. So it will not work on Windows 2000.

  Hmmm. Woody didn't say exactly if the printer actually prints

  Well I wouldn't went all the trouble to clean the building a Machine virtual Windows 2000 Pro SP4 with VMware Tools installed and printers enabled for the Virtual Machine settings and took all the dialog boxes and to make a film of the if I did had not bother to actually check and see if she would print!

  Find attached an image of a Windows 2000 printer print Test and note the relevant information.

  Computer name: W2KVM

  Name of the printer: HP LaserJet 4050 on MacBook Pro

  Printer model: TP output gateway PS

  Support: Yes

  Port name (s): THIRD:

  Note: because the printer is a B & W LaserJet I guess that the "support: Yes", it's that the "printer model: TP output gateway PS ' supports color and will therefore work with color printers as well.

• explanation of the declaration necessary please

  I'm tracking a variable bug using traces (AS2.0).  Could someone please explain me what the statement in red below the means and where I should look? It seems to be another concept to address that I'm missing.

  scrolledMC is a container of MC that contains the dynamic text field (auto size), which is the text that is currently the subject of a scroll.

  scrollContent1 = _parent. scrolledMC / / this statement made '_parent' reference to the original item of Lib or the MC in which

  trace ("scrollContent1 =" + scrollContent1)

  result of the trace

  scrollContent1 = _level0.instance703.instance709.scrolledMC / / what this means? 'instance' of what? what relevance to numbers have?
  

  1. how to display the content of the "_level0.instance703.instance709.scrolledMC" in the form of text content can I read?

  2 every time this trace is running the 'instance' figures are different. ever the same numbers. so if I try to trace (_level0.instance703.instance709.scrolledMC) he comes back undefined.  These figures vary to great more swf turns and me back to the page with all traces. Whats up with that?

  3. how different _root _level0?

  4 if I trace scrolledMC I get «»

  Thank you

  Joel
  

  As I have already said, the "instance" are parts without the name of the place where scrolledMC life.  You just said... "'scrolledMC' is the part of the Text_scroller", so these instances that question you are the other parts of him that contain it. they are not appointed manually, so that the program assigns them generic names.

  Yes, they try once more to make the forums better (not yet as well).