Optiarc DVD RW AD7710H driver does not install

Similar Questions

• DVD/CD-RW drive does not-Tecra A4

  Hi, I have a problem with my Tecra A4.
  My DVD CD - RW drive does not work properly (power is there, but it does not appear on the system), I have temporary installed a drive of DVD - RW from my HP laptop which works very well.
  I tried to run my restore disk (never used), but nothing happens (press and hold C to start). This will only work with the good drive installed or I do something wrong?

  p.s. I bought this second hand, but it's new. He had a damaged screen I have replaced

  Julian

  If the old drive will not read media if it s damage.
  You know that not every disc is compatible with the device because of the csel/slave/master settings.

  You said that the button C doesn't allow you to boot from the disc.
  In this case, I would recommend to get into the BIOS, and there you can change the boot order.
  However, this trick is everything works only if the new drive is compatible and supported

• Satellite Pro A120: DVD/CD-RW drive does not work

  Hello: the dvd/CD-RW drive does not work. apparently it has been disabled somehow! Any ideas on how I can turn it back on?

  Have you tried the Device Manager and it says it works normally!

  Any ideas please?

  Thanks :)

  > apparently it has been disabled somehow
  I put t think that the disc has been disabled!

  How someone or something should turn off the drive? You have disabled the drive? I don't think so!

  You said that the drive appears in Device Manager. So I guess that the drive is enabled and is recognized by the OS.
  You are getting error messages or what's wrong?

  Perhaps the reader can read or burn CDs or DVDs.
  This happens if the lens of the drive cannot calibrate properly and can not handle the inserted media.

  Maybe the replacement drive is required!

• Microsoft Update for hp LaserJet 3015 PCL 5 driver does not install in Windows 7

  I use Windows 7 update.
  Microsoft Update for hp LaserJet 3015 PCL 5 driver does not install. He says 1 optional update is available almost every day, then when I try to install, it does not install and it says that the update is not necessary. Even once when I check updates, it says 1 optional update for the printer is available from Microsoft. And the story continues. I tried to reinstall the optional update, but the same problem persists perennielly

  Is this the driver you are looking for?
  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=503519&prodTypeId=18972&prodSeriesId=503548&swLang=8&TaskID=135&swEnvOID=4062

  Looking for HP for the pilot because it is better to get these live drivers from the manufacturer. TaurArian [MVP] 2005-2010 - Update Services

  No, these aren't the droids, uh, I mean the drivers he was looking for.

  In fact, it's better to get the new drivers from the HP website, you will notice the link you provided that the options only are available for this printer under Windows 7 drivers universal. I regularly have problems with universal drivers and strongly recommend to avoid as much as possible.

  I agree with the question of the original poster, which, after more than two years, remains unanswered by Microsoft. It seems that MS has a driver PCL 5 (not universal) updated specific 3015, but it fails to install the Windows Update control panel. I finally gave up on it, right click on the update and selected the option to hide it from view.

  Why bother with a solution when I use the button "Sweep-It-under-the-carpet" practice of Microsoft?

• DVD/CD RW drive does not open

  Drive DVD/CD-RW door does not open.  Tried to open it by going to my computer, media player and selecting "EJECT", but I get a message "error with the player."  Any suggestions?  I have not had any problems in the past with the drive and burned many CDs.  It is not a CD in the drive now.  My computer is only 6 months old.  What can I try to get to open my car door?

  Hello

  For the readers of the status bar:

  Sometimes they get stuck. There is a small hole on the front of the CD drive that you can stick a
  a paper clip that will release him and the reader to open.

  Create a trombone in car Opener
  http://pcsupport.about.com/od/tipstricks/HT/ppdropen.htm

  Open a CD/DVD player with a paper clip.
  http://www.josepino.com/?open_cd-dvd_paperclip

  =================================

  For the readers of the slot:

  Check with the manufacturer of system on how do to eject the disc.

  Dell xps m1330 dvd drive will not eject cd inside<-- check="" these="">
  http://www.FixYa.com/support/t2643828-dell_xps_m1330_dvd_drive_will_not_eject

  Be careful as you may damage the player using the method below:
  
  You may need to get the driver to work 1 However, this could still work.
  http://www.tech-tweak.NET/2009/11/how-to-eject-STUK-DVD-from-slot-load.html

  The method used on the Mac could work
  http://www.YouTube.com/watch?v=wpWieIoBBrk

  How to disassemble the laptop (Dell XPS M1330)<--- voids="" any="" warranty!="" this="" is="" an="">
  http://ahwee.com/how-to-disassemble-laptop-Dell-XPS-M1330

  Also have heard double tape on a credit card or play can work.

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Why the DVD of Win7 installation does not install network controller?

  I described my adventure with a virus earlier. At one point, I went to Micro Center and bought a new drive for Win7 Home Premium install. The installation seems to be going OK, but when it's over, I wasn't able to get on the net because the driver for the network controller was not installed. I made 3 attwempts, but all have failed for the same reason. Why?  As far as I know, Microsoft does not ship any DVD W7 with the missing files, and I believe that the disk cannot be written and corrupted, so why these files not installed? Does anyone have a similar experience?

  Maybe it's a new network controller, which Windows 7 has not built in the class driver for. You can go to the website of the manufacturers on the computer you are using now and download the driver.

• Satellite P10 824: modem driver does not install

  I have a tosiba Satellite P10 824 and the modem driver not install what can I do? This page driver is installed but the modem does not work.

  Hi Cienciala

  If the reader is already installed and the modem is correctly listed in the Device Manager, do not try to install it again and again. I advise to enter the properties of the modem in the device and on the diagnosis tab Manager list, you can use Query modem and verify the results.

  If the modem does not work it may also be the configuration dial problem.
  By the way there is also a useful site, you can check http://support.toshiba-tro.de/kb0/FAQ35006G000UR01.htm

• Satellite M40-185: DVD super multi drive does not read the CD

  I own a Toshiba Satellite M40-185. It is mounted with a carpet * a DVD-RAM UJ - 831S.
  When I put the CD - R, which are supposed to work on this drive however it read as a CD - R [i.e. the icon changes from DVD - RAM drive in my computer to a CD - R]

  However, when you double-click the drive it says D:\ accicble not. But it works fine with DVD.
  Recently, I found that it stops between buring DVD as well. I got the replaced disk from Toshiba, but it was not to last long either.
  I wonder if his software level problem.

  I tried to update the firmware but it does not work because it's another drive for this what is mentioned on the website for drivers...

  Maybe it s only a registry error?
  I read different statements here in the forum and especially the deletion of in the upper and lower registry filters helps to address these issues.

  For more information, see this page of Microsoft Knowledge:
  http://support.Microsoft.com/kb/270008/en-us

  Completely remove the Upperfilters and Lowerfilters from the following registry key values:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  and then restart the laptop

  Good luck

• My dvd/cd rom drive does not open

  I looked for mechanical problems, I've updated the driver, I tried manually open (press the Open button), I tried to use the computer to open, but all without success. This has happened as my computer starts does not sometimes after it has been switched off.

  Hello

  Try using a tip of a paper clip to open the tray.

  "How to create a trombone in car opener.

  http://pcsupport.about.com/od/tipstricks/HT/ppdropen.htm

  "CD-ROM, DVD or other drawer not open."

  http://www.computerhope.com/issues/ch000214.htm

  See you soon.

• DVD/CD RW drive does not work after update from Vista Premium for Vista Ultimate

  I have a gateway notbook, series P-7805u - 8400.  DVD/CD RW drive was working fine until I upgraded to Vista Ultimate.  Now, I can't even restore to a point before the update, nor that I can run my recovery disks.  I have to correct this problem.  I hate not having a phone number where I can at least speak to a technician or a place where I can scream my lungs.  I need help, real help.

  Something is terribly wrong when you spend too much for a product that doesn't work not as advertised and then you can't get the help you need when you need it.  No wonder they want to keep things civil here...

  Oh my God, bless you... it works!  After removing the filters (try manually this hotfix if the Fixit 314060 does not
  ( http://www.pchell.com/hardware/cd_drive_error_code_39.shtml) after reboot, everything is back.  THANK YOU, THANK YOU, THANK YOU.

• Adding a new dvd/CD-RW drive does not work on my PC 4600

  Hi, my laptop comes with a standard cd-rom drive and I bought a dvd/CD-RW drive to replace. When I enter it it appears power because I can open the drawer and the light comes on when I turn on the computer. However it is not coming in my computer.
  I tried several disks so that the player I use is not defective.

  can someone please help me with what I need the dvd function on my laptop for my work.

  Thank you very much

  Tommy

  Hello

  New device is recognized by the OS? Can you use it at all? Is there an error message or is defrost just marked in Device Manager?

• USB for C7280 driver does not install on a laptop HP DV8-1093 running Windows 7PRO

  When I plugged my C7280 to an HP Desktop running Windows 7 Pro 64 immediately I had an advertising icon that the drivers are loading it takes 5 minutes and several drivers have been installed, I can print and scan

  on my laptop DV8-1093 is also running windows 7 64 pro, when I connect the USB cable nothing happened, no icon in bottom right and no driver s are installed, I check the cable that he works on the desktop

  WHY drivers won't load

  What can I do for installing the drivers

  Thank you

  François

  Hi frmichaud,

  I understand that the software was not automatically installing for the HP Photosmart C7280. I'll try my best to help you with this problem. The software and drivers are not previously installed on the laptop.

  Here is the download page for software HP Photosmart full feature and drivers, download and save to your desktop.  Follow the steps described in this document for the installation of the printer software in Windows 7 for a USB cable connection. Make sure you unplug the USB cable from the computer and wait that you asked before you plug it into the computer.

  I hope that this information help, please let me know how it goes.

  Thank you

• CD-ROM/DVD-ROM device driver does not support SQL Server 2014

  My computer:

  -Win 7-64 BIT.

  -SQL server 2014.

  -CD-ROM/DVD-ROM device.

  Win 7 has a problem when SQL Server 2014 creates the database on CD-ROM/DVD-ROM device file.

  I'm asking in the forum of SQL Server and the response is ", this question could related to the driver for your drive as SQL Server DeviceIoControl calls during the creation and opening of any data file or journal. In this case you will need to discuss with your provider of storage device on the driver problem. »

  Reference: operating system error 1 (function Incorrect.) met.

  My question: why CD-ROM/DVD-ROM device driver support SQL Server 2014?

  And how to solve the problem?

  My driver as follows:

  

  Your words:

  "Win 7 have a problem when SQL Server 2014 creates the database on CD-ROM/DVD-ROM device file. .

  I ask in the forum for SQL Server and the response is " " If this problem could be linked to the pilot of your drive as SQL Server DeviceIoControl calls When you create and open any file of data or log. In this case, you will need to discuss with your provider of storage device on the driver problem. "

  Forum SQL of importance or ask your optical drive manufacturer.

• software for the printer driver does not install

  My printer is C7100 all-in-one.  My OS is windows 7 - message comes back "could not install any software.

  I recommend traverse "Programs and features" in your control panel and manual uninstall of the printer, then shut down and restart your computer. If the files do not uninstall, then you can have a deeper problem with your operating system.

  Once the software is missing, try again after the above link and by installing the full setting software.

  Let me know!

• Downloaded Driver does not install correctly

  Print HP 2410 died, but everything on my pc and the set up worked well.   I got the used 2610xi.  I removed the 2410 and tried the disc to instal 2610... She has no cause not windows 7... closed it... went to HP.com and download the driver and 5 updates and then install the driver that seems to be okay and then I did the updates... few of whom said there was no driver for updates to update.   Then I got a message for my PC. I did and then she was installing drivers for, while... and there was a box filled showsing but the last line that says driver failed... but printer showed that he and ready.  I did a scan and it scanned for connection was good... but it would ' t print!  Whenever I hit print it says that I should open a "note" to use this feature...   On the line and went to find this post http://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/can-t-install-software-for-all-in-one-photo...   so I followed what was said exactly... I removed the 2610, I unplugged the USB printer cable, I have reboted PC, I extracted the file of the pilot... and he showed extraction... then more NOTHING... hard drive is swirling as something that happens, but he was 15 minutes now... show nothing.    I have a fast modern PC... nothing takes this time who is going to work.    I confirmed from the properties of my computer I have Windows 7 64 bit... my PC and printe rset up has worked well with the 2410 until he broke.    Never had so many problem setting up a printer.  HELP Please

  Hi Notanother1,

  Thank you for your answer! What happens when you use the printer HP install wizard for Windows, does make a difference?

  Hope to hear from you and have a great day!