driver MpKslf42be8d6 error code 24

Similar Questions

• Audio driver problem - error code 39 - Yamaha Satellite 2410 304

  I have a Satellite S2410-304 equipped with Yamaha AC - XG. After installation of SP2 it used to work normally for 6 months, but somehow the "speaker" icon missing yesterday.

  Device Manager panel shows a yellow exclamation (error code 39) for the device of Yamaha AC - XG. I tried to install the original drivers, the v6.13.10.2152, the v6.13.10.3152 and the most recent 3157, 3159. But every time Windows notifies that the drivers are not MS signed.

  What can I do about it?

  Hello

  Audio drivers are not signed by Microsoft, but you can install these drivers and they work!
  Only a notification message and has no influence on the installation of the driver or features

• 0xe0f00013 (new hard drive) retrieving error code

  Laptop model: HP envy 14 beats 1260se, windows 7 64 bit.

  OK, here's the story. A couple of weeks ago, I did a test drive and this error 'problem of intelligent control' came, and after spending some time on the internet, I discovered that I need to change my hard drive. I created a post as well, here is the link:http://h30434.www3.hp.com/t5/Notebook-Hardware-e-g-Windows-8/Smart-check-issue/m-p/2337229

  So now, I bought a new hard drive and the model is: 750Go momentus XT (link:http://www.amazon.co.uk/Seagate-750GB-Momentus-Serial-Hybrid/dp/B0068QO82G/ref=sr_1_1?ie=UTF8&qid=13... )

  I replaced my HD and so my recovery disks to reinstall windows and basically copy all the original files in the new HD. However, at the end of the restore process (7 discs), I received this error: "Recovery Manager could not restore your computer by using the original image. Please contact HP support. "Error code: 0xe0f00013.

  And then after I pressed 'Finish', he went on the screen of my laptop which basically a HP logo appears and it stops right there!

  I have no idea what to do now and it becomes really annoying!

  Thank you, Aria.

  Hi Aria,

  It seems that you bought a hybrid car and this is probably what causes the error when you try to use your initial recovery disks.

  Here is another solution, you can try which should allow you to load Windows 7 on your new HARD drive.

  Before you try the following, make sure that you can always read the character product activation key 25 on your label Windows COA (5 blocks of 5 alphanumeric games).

  An example of a COA label can be seen here.

  You can create a Windows 7 installation disc yourself using another PC - just download the good Disk Image ( must be the same version that originally came with your laptop - IE Windows 7 Home Premium 64-bit ) from the link below and use an app like ImgBurn to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write that an ISO on a disc is Here. These Images are clean and a well respected source, however there are only limited versions available.

  Windows 7 sp1-iso-official-32-bit-and-64-bit

  Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  All pilots additional and the software, you may need can be found here.

  Kind regards

  DP - K

• Driver video error Code 10 after the upgrade to Windows 7

  Upgrading to Windows 7 & have the following error messages:

  Standard VGA graphic card work not only can not start (Code 10)

  Converter USB - LAN has no driver

  SMA 851 X USB to Fast Ethernet Adapter

  During the initial installation of Windows 7 the monitor works but when Windows upadates are applied it gives the messages described above. Everything worked then on Vista... but also Vista would work!

  Dell does not have a driver for a monitor solution - 2 years. I was running as an extended desktop on a Dell Inspiron 6400 with 2 GB of RAM, new 500GIG Hitachi hard drives.

  Also cannot load the Office Small Business 2007 Business Contact Manager.

  Hi remaxguy,

  See the following article on setting error Code 10:

  http://support.Microsoft.com/kb/943104#appliesTo

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Drive hard error Code 2000 - 0142

  Inspiron 15 (3531, mid-2014)

  I tried boot diagnostic that the result has failed with the error code 2000-142.

  I have used a quick diagnostic race through dell online support site - it shows critical errors found

  for hardware failure then suggested for a replacement.

  Targeted both reading test SMART short self-test is broken.

  We hope to hear from you on your recommendations of experts on hardware issues.

  [Admin NOTE: maintain the label removed in accordance with the TOU strategy]  [Admin NOTE: deleted in accordance with the Express service code TOU strategy]

  Ryan Ibarreta - [Admin Note: personal information]

  Philippines

  Error code 2000-0142 usually indicates a failing hard drive / failed, first of all, try to remove and reinstall the hard drive, then re-run the diagnostic tests and see if you receive the same error.

  If the same error is received, the hard drive has failed, then you need to replace it.

  If you have a warranty from Dell, contact Dell Technical Support for a replacement hard drive.

  Bev.

• Backup on an external hard drive, the error code 0 x 81000019 a snapshot could not be created. Pls chk "vss" and "spp" application event logs.

  A snapshot could not be created. Please check the spp and 'vss' ' applications for more information event logs.

  Details: Insufficient storage available to create the shadow copy storage file or other shadow copy data. Error code 0 x 81000019.

  The size of the external drive is free to Go 465,65 Go 465,75. Also "size of the backups is not available" is displayed under the size of the disk in GB. The size of the backup copy is 57 GB.

  Event logs see the backup error event ID 521

  GENRAL:
  Save the operation which started at 2010-03-11 T 13: 41:53 failed because the service operation volume shadow copy to create a shadow copy of the volume during backup failed with the error code 2155348249.

  Details:
  + System
  -event data
  backup time 2010-03 - 11 t 13: 41:53.466000000Z
  Error code 2155348249
  Error Mssg % 2155348249

  Hi Gilles Pelletier,.

  1. check the shadow copy Volume service in the services window. Use the following steps to check:

  i. click on start and type services.msc in the search box

  II. the search for the shadow copy Volume service

  Please let us know the status and startup type. Make sure that the startup type is automatic

  Steps to set the auto services

  i. search for the service

  II. right-click on the service

  III. If the service is stopped and then starts the service

  IV. Select Properties

  v. and in startup type, select automatic

  2 disable the firewall / anti-virus temporarily installed on your computer and then check if the problem still persists. If the problem is resolved, you will need to uninstall the software and reinstall it back or change the settings and check.

  3. even check a drive for errors: http://windows.microsoft.com/en-US/windows7/Check-a-drive-for-errors

  Check this link which has the similar problem: http://social.technet.microsoft.com/Forums/en/w7itproperf/thread/9b18bc73-26e5-4b28-819f-11628ebbf5e2

  Thank you, and in what concerns:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Toshiba 320 GB external USB HARD drive - 10 error Code

  Basically, I bought one of these today and put everything and he put in place and for some reason, my computer refuses to recognize or even start it. Initially, he recognized new hardware, but then nothing happened. I found it in device manager and it says that it will not start due to a "Code 10". Anyone know what it is?

  Then I turned off my computer after about an hour of nothing, then tried again, once more he recognized a second but a pop up came that said an error has occurred and may not work properly. Again, someone knows why this happened?

  Any help would be greatly appreciated. Thank you.

  Hello

  Code 10 means that the device could not start.
  Make sure you have the latest driver installed for your device. You may also be able to resolve this issue by removing the device in Device Manager, and through the Add New Hardware Wizard in Control Panel.

  It is also possible that your USB HDD needs an external power supply.
  If the USB device needs more than 500 ma, so usually an external power supply is required.

• No access to the DVD drive - 38 error code

  Update Driver published 07/07/08 to 23:59 has been installed on my system as made by Toshiba Tempo but rebooting my machine, I get error 38 (according to Vista) that prevents the new driver installation as the old pilot is resident in memory... ?? Effectively, this means that I can't access or see my DVD player more in other ways than in the page Manager devices Control Panel. Option driver restore is not available, perhaps because it was an update of the firmware. The message on the device properties page is as follows:

  Windows cannot load the driver for this hardware device because a previous instance of the device driver is still in memory. (Code 38)

  The installed updatre was frmwre-20080707134447. It includes an Adobe document that tells you what to do and how to ensure that your drive needs to be refreshed, which was easy to follow and loose my machine.

  I tried to uninstall the device and the driver, but whenever I have to reload the same error occurs.

  I'm really impressed and quite embarrassed, because it is a recommended Toshiba firmware update done using their system of Tempo, ideas or advice welcome.

  Thank you

  Matt

  Hello

  Do you see a CD/DVD drive in Device Manager?
  If so, then remove it from the list of devices.

  Then access the registry and delete the Upperfilters and Lowerfilters completely from the following registry key values:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  Finally restart the laptop and check if the CD/DVD drive would still be functions

  Further details can be found here:
  http://support.Microsoft.com/kb/270008/en-us

• CD DVD drive receive error code 39

  I have a new Dell 1525 with vista.  The shows of cd/dvd drive in Device Manager and properties gives the following error:

  Drive: TSST corp DVD +-RW TS - L632H ATA Device

  Windows could not load the device driver for
  This material.  The driver may be corrupted
  or missing (code 39).

  Drive does not appear in my computer.

  I tried to reload the driver from the rack in the search on the web with no luck.

  Still got the same error.

  What to do next?

  
  

• Toshiba laptop drive automatic error Code 10

  Im getting a code 10 on my laptop drive automatic backup of toshiba. Ive tried uninstalling and reinstalling just says cannot start the device. I think im missing a hardware device driver, but I can't find this driver anywhere online. Can someone please help:)

  Hello Chan,

  I found your posts on the Toshiba site, I take it no luck with the new replica? Also, have you tried to contact Toshiba technical support? It seems that they have heard of this problem before (based on many previous occasions this problem came) .f you don't have, I would say that you communicate with them.

  That said, two possible solutions from another thread which may apply to your situation:

  1. Sometimes if a USB port not properly initialize on startup Windows installs a "unknown device" driver by default. Of course nothing plugged port at this time won't work. Sometimes it can continue to attribute this driver on the same port on subsequent reboots. Search for all entries 'unknown device' under Controllers USB in Device Manager then uninstall them. Right click on "Find the hardware changes" or reset must be reinstalled the correct USB device driver.
  2. The problem with the hard drive occurs if you turn on the USB drive after that the computer was started? Some interfaces of USB drive can interfere with Windows to detect the USB controller that they are connected correctly. Only seems to happen if the player is powered on while Windows starts.

  I guess that Technical Support Toshiba offers these strategies you anyway, so you can as well try now them. Let me know if this helps you.

  Kind regards

  BearPup

• Can not install the printer driver. Error code 0 x 0000490.

  I have Windows Vista and I have a printer HP 3512. For some reason, I can not install the printer and I keep getting an error 0 x 0000490. Help, please?

  Moved from Vista to install, upgrade and activate Forum.

  Hi Courtney,

  Please contact the Microsoft Community.

  I'd like you first try printing HP and doctor Scan.

  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&DLC=en&docName=c03286146

  After that, I would have you to refer to this article-

  http://h10025.www1.HP.com/ewfrf/wc/documentSubCategory?tmp_task=solveCategory&cc=us&DLC=en&LC=en&product=5241114

  We know if that helps your cause.

• Bad directsound driver. Error code 88780078 (Windows 7)

  Means - This is a foro Público para as nunca publicar information privada como el correo electronico o phone numbers!

  Ideas:

  • Programs are having problemas con
  • Error messages
  • Los recent changes made in su equipo
  • What is han intentado did el problema

  I'm sorry, but these Vista Help Forums only provide support in English.

  http://support.Microsoft.com/common/international.aspx

  To ensure that you receive support appropriate for your location information, select your region setting in the list on the link above and then click the arrow button.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  And for any Windows 7 questions:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to / stationed there.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Satellite L20-214: yellow exclamation Ethernet controller - error code 28

  Hello

  in device manager ethernett controller has a yellow exclamation point.
  When I click on update drivers it says error no driver found error code 28. can someone please help do not have any idea what that's all.
  see you soon

  Code 28 mean that the drivers for this device are not installed.
  To resolve this issue, you must install the correct drivers.

  Which laptop computer and operating system you have?

  Go to the page of European Toshiba driver and download the right driver LAN for this laptop!

• Creative cloud 71 error code

  

  (this application is unable to boot from a networkdrive. Copy it to a local folder and then restart.)

  ErrorCode: 71

  Sorry for the bad transaltion...

  I downloaded creative cloud, wanted to install it and then that this.

  What should I do?

  Greetings,

  Cabbagehead

  Hello

  Please see: -.

  Error 71 - cannot install CreativeCloudSet - Up.exe that it cannot be run from a network drive

  Error code: 71 when trying to install the creative desktop application Cloud (Win10)

  Hope this helps!

• Impossible to install the driver of Logitech Webcam - error code 19

  Hi gurus,

  I just buy Pavilion m9400t with Vista x 64, Dual Core Quad Q6700.

  Install Logitech QuickCam Pro 4000 without problem, so I decided to upgrade with the new webcam (Quickcam communicate Deluxe) and the beginning of the problem.  Install the new driver/software without problem, after reboot when I try to use the Webcam webcam cannot be used..., check the Device Manager for this webcam and found he said one! status, with the following error code:

  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (code 19).

  Tried the following, but nothing works:

  1 uninstall and reinstall using the new driver from Logitech.

  2. Uninstall and reinstall in safe mode.

  3. Uninstall and reinstall using the generic driver

  How can I get rid of this error code 19?

  Thank you

  In this issue fixed. Used regedit folder specific location and delete the LowerFilters entry, exit and it will get rid of the error code 19 from Device Manager, not even require a restart.