DRY 1941/licenses K9 IPSec Remote Access

Similar Questions

• IPsec Site to Site and the question of the IPsec remote access

  Our remote access IPsec 3DES 168 bit encrption has the value

  If we want to allow a remote user to get out of a tunnel to another site must be so 3DES encryption for the Tunnel?

  This tunnel is currently defined by AES.

  If I understand your question the answer is this:

  The VPN client will connect to the ASA with any encryption method, he chose.

  If the VPN client then runs through a tunnel from Site to Site to another location, it uses the encryption method specified in the tunnel from Site to Site.

  This is because as the settings for the client VPN applies only when he puts an end VPN on the ASA.

  When the customer traffic, passes through a different tunnel, the settings for this tunnel applies.

  Hope I answered your question, if not please let me know.

  Federico.

• VPN - IPSec remote access

  Hi community support.

  I have an ASA with double tis (gig0/0-gig0/1) and gig0/1 has a default route with admin distance from 254 to back it up.

  I just created Cisco Anyconnect on the SAA the wizard and I can connect to both interfaces.

  IPSec tunnel configuration is also there and I tried to create an IPSec VPN entry on the with my iPhone and I can connect to gig0/0 or gig0/1 if gig0/0 is stopped.  But I can not connect to gig0/1 if gig0/0 is in place.

  When I run ' isa crypto to show his ", I get the following error:

  ciscoasa # show crypto isa his

  IKEv1 SAs:

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: X.X.X.X
  Type: user role: answering machine
  Generate a new key: no State: AM_WAIT_MSG3

  So the question is, is that what it means and why it works if I close gig0/0 (which is the main interface) and would be why Cisco Anyconnect works also with two interfaces up and customer VPN Cisco Legacy does not work?

  Thank you

  Hello

  What is expected due to the way table routing of the SAA is currently designed. ASA supports not only routing table overall but the routing by interface table as well.

  In the case of IPSec VPN, ASA-control path will do a search of route for the response packet. This search returns the interface of ISP outside/primaries as the best route, but because you tried to connect to the backup, ASA will drop the packet.

  In the case of Anyconnect VPN or SSH/Telnet, ASA creates a connection to flow forward and reversed to the original application flow and does not pass through the route search mechanism and uses only the output interface (where the request has been received) to send the response. AnyConnect session will follow the routing of each interface table.

  Check it for your reference: -.
  https://BST.cloudapps.Cisco.com/bugsearch/bug/CSCsg39338/?reffering_site=dumpcr

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• AnyConnect VPN client can be used for IPSec remote access VPN connection?

  I think I heard it somewhere that AnyConnect VPN can be used for connections SSLvpn IPSec VPN. Is this possible? Thank you!

  No, the Anyconnect software cannot be used to establish the framework for a VPN IPSEC IKE.

• Areas of IPSec remote access VPN Login multiple users

  Hi, we are currently migrating from an Active Directory, existing to a new domain.  We currently use the client for users of Cisco VPN IPSec (ASA5520, version 9.1) software to to connect to VPN, and we have our DCs existing, specified as servers Radius for authentication of the user.

  We need to migrate to a new domain within our Organization, using different domain controllers.  How can I specify the users in the new domain to be authenticated using a set of domain controllers and users in the existing domain to use another set of domain controllers?  This is adjustable by creating a new group policy?  I don't see anywhere to specify that.  We have to enable authentication of users in both areas during the process of transition, it will be a gradual migration.

  Thanks for the help.

  You will need to create a new server group AAA pointing to the servers in the new domain for authentication.

  Then make a new connection profile that uses AAA server group.

  Your users will have to choose the connection profile (absent some more advanced stuff like issue user certificates that can be archived attributes that match a profile or another).

  This could also be done with ISE 1.3 who can act as a RADIUS server and join multiple AD domains on backend as identity stores. (or even with ISE 1.2 If you use one of the AD directories like LDAP vs native AD store).

• RV042G REMOTE ACCESS VPN Config Shrew Soft

  Hello

  I am trying to set up a VPN with IPSEC remote access, I have a router Cisco Small Business RV042G. I have managed to connect with the QuickVPN client using a previously created user. I also managed to establish a connection with the TheGreenBow pre-shared key customer with customer authentication by IP address or by mail. Exactly the same method I managed with the Shrew Soft VPN Client. I would like to Shrew Soft VPN with only establish a connection with the nicknames as if only the pre-shared key is used all over the world can access VPN set up on this computer.

  shrewsoftauthlocalidentity.PNG

  

  shrewsoftauthremoteidentity.PNG

  

  shrewsoftauthcredentials.PNG

  

  

  To sum it up can you tell me what configuration must be put to use the identification of the user only with the Shrew Soft VPN Client?

  Thank you very much.

  Hello

  Usually it is used Mutual PSK + XAuth, when you want to set up user and password, outside the pre-shared key authentication.

  But RV042G don't support XAuth, which means that you can not create a separate user/pass to connect VPN Shrew.

  Kind regards

  Bismuth

• Redundancy ASA - Client to the remote access (AnyConnect or IPsec) VPN Cisco to 2 PSI

  Hello

  I realize that the true public access redundancy require routers and BGP need &AS#; but some can't afford such a solution.  Should someone have ASA 5510 dry + with 2 of the ISP could use IP SLA functionality for primary education to save the failover, etc..  What VPN clients for remote access (SSL or IPSec).  I'm curious if you have any other solutions/configurations on it to allow either of these customers, AnyConnect or IPsec, to try the primary counterpart and after a few failed attempts over fail to backup (even if a user tries to establish a VPN)?  I know that one of the possible solutions may use a domain name FULL peer IPSec or AnyConnect client input, then maybe public operator DNS TTL change or other hosted / failover services... but these "proxy" or DNS services are not the best solution because there is cache and other associated DNS weaknesses (right)?  These are not infallible fail-over, I'm sure that some users might succeed and some may fail; I do not know administrators will be like that as much as they like going to the dentist.

  Anyone who has any ideas or possible solutions?

  Thank you.

  Hello

  Backup servers are supported by remote access VPN clients.

  The client will attempt to connect to the first IP/configured FULL domain name and will try the following in the list, if no response is received.

  http://www.Cisco.com/en/us/docs/security/vpn_client/cisco_vpn_client/vpn_client46/win/user/guide/VC4.html#wp1000747

  Federico.

• Remote access IPSec client IPSec network remotely

  Hello

  I have the following problem.

  We have two sites to connect with an IPSec VPN L2L.

  Site A: 192.168.13.0/24

  Site B: 192.168.2.0/24

  On both sites, we an ASA5505 (basic license) to finish the tunnel.

  On Site B, we also got a remote access vpn to which we can connect using the vpn client.

  The lan2lan tunnel works very well and if the remote vpn access.

  Now I want to connect to the Site using my vpn client connected to Site B.

  Configuration:

  Site b:

  same-security- allowed traffic intra-interface

  same-security- traffic permitted inter-interface

  nat network object

  Subnet 192.168.2.0

  NAT dynamic interface (indoor, outdoor)

  NAT (inside, outside) static source 192.168.2.0 255.255.255.0 destination 192.168.13.0 static 255.255.255.0

  the SITEB object network

  Subnet 192.168.2.0 255.255.255.0

  network of the VPNPOOLB object

  255.255.255.0 subnet 192.168.25.0

  network of subject-group 10

  object SITEB

  object VPNPOOLB

  access-list standard split1 ip 192.168.13.0 allow

  access-list standard split1 permit ip 192.168.2.0

  IP local pool pool1 192.168.25.1 - 192.168.25.254 255.255.255.0

  access-list allowed extended L2L object-group 10 ip 192.168.13.0 255.255.255.0

  L2L 1 crypto card matches the address L2L

  REMOTEACCESS group policy

  Split-tunnel-network-list value split1

  address value pool1 pool

  Site A:

  NAT (inside, outside) source static 192.168.13.0 255.255.255.0 static destination 192.168.2.0 255.255.255.0

  NAT (inside, outside) source static 192.168.13.0 255.255.255.0 destination 192.168.25.0 static 255.255.255.0

  the SITEB object network

  Subnet 192.168.2.0 255.255.255.0

  network of the VPNPOOLB object

  255.255.255.0 subnet 192.168.25.0

  network of subject-group 10

  object SITEB

  object VPNPOOLB

  L2L 192.168.13.0 ip extended access-list allow 255.255.255.0 object-group 10

  L2L 1 crypto card matches the address L2L

  There is no vpn-filters or other special air in place...

  So tempted to my Site A vpn client ping while I was debugging ipsec 255 on site B:

  the asa matched l2l-tunnel for traffic from 192.168.25.x to 192.168.13.x

  .. but when im making a detail his see the crypto ipsec is no packets be encrypted...

  then of course no package to reach my asa on site one.

  Everything but the connection from the pool of clients to implement one works very well.

  concerning

  TJ

  A number of things:

  (1) B site, crypto ACL is as follows:

  access-list extended Lan2Lan allowed object-group 192.168.13.0 ip 255.255.255.0

  --> doesn't look like not to he refers to any object-group in the access list.

  It should be:

  access-list allowed extended Lan2Lan object-group 10 ip 192.168.13.0 255.255.255.0

  (2) it is also not advisable to configure the dynamic map with sequence number low instead of the greatest number of seq in the crypto map. Your site has at present the following:

  card crypto RemoteAccessMap 1-isakmp dynamic ipsec RemoteAccess

  RemoteAccessMap 2 crypto card matches the address L2L

  I propose the dynamic map to a number of lower sequence as follows:

  No RemoteAccessMap 1-isakmp dynamic ipsec RemoteAccess crypto card

  card crypto RemoteAccessMap 65000 ipsec-isakmp dynamic RemoteAccess

• Configuration remote access VPN (IPSec) using FULL domain name

  Hi friends of Cisco,

  We have the DNS (only the internal IP) within our network, right now that we have configured VPN for remote access using public IP address and connect us with the same public IP address. I need help to use the domain name FULL rather than use public IP.

  Can you please provide the configuration for this.

  Feature: ASA 5520

  Type of configuration: IPSec

  Thank you

  Estel

  Hi Philippe,.

  You can use one of the free Web of DNS dynamic sites and configure ASA to dynamic DNS.

  Reference - http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/basic_ddns.html

  HTH,

  -Dieng

• Problems with remote access IPSec VPN

  Dear Experts,

  Kindly help me with this problem of access VPN remotely.

  I have configured remote access VPN IPSec using the wizard. The remote client connects to fine enough seat, gets the defined IP address, sends the packets and bytes, BUT do not receive all the bytes or decrypt packets. On the contrary, the meter to guard discarded rising.

  What could be possibly responsible or what another configuration to do on the SAA for the connection to be fully functional?

  It can help to say that Anyconnect VPN is configured on the same external Interface on the ASA, and it is still functional. What is the reason?

  AnyConnect VPN is used by staff for remote access.

  Kindly help.

  Thank you.

  Hello

  So if I understand correctly, you have such an interface for LAN and WAN and, naturally, the destination networks you want to reach via the VPN Client connection are all located behind the LAN interface.

  In this case the NAT0 configuration with your software most recent could look like this

  object-group, LAN-NETWORKS-VPN network

  network-object

  network-object

  network-object

  network of the VPN-POOL object

  subnet

  destination of LAN-NETWORKS-VPN VPN-NETWORKS-LAN static NAT (LAN, WAN) 1 static source VPN-VPN-POOL

  Naturally, the naming of interfaces and objects might be different. In this case its just meant to illustrate the purpose of the object or interface.

  Naturally I'm not sure if the NAT0 configuration is the problem if I can't really say anything for some that I can't see the configuration.

  As for the other question,

  I have not implemented an ASA to use 2 interfaces so WAN in production environments in the case usually has separate platforms for both or we may be hosting / providing service for them.

  I imagine that there are ways to do it, but the main problem is the routing. Essentially, we know that the VPN Client connections can come from virtually any public source IP address, and in this case we would need to default route pointing to the VPN interface since its not really convenient to set up separate routes for the IP address where the VPN Client connections would come from.

  So if we consider that it should be the default route on the WEBSITE of the ASA link, we run to the problem that we can not have 2 default routes on the same active device at the same time.

  Naturally, with the level of your software, you would be able to use the NAT to get the result you wanted.

  In short, the requirements would be the following

  • VPN interface has a default route, INTERNET interface has a default route to value at the address below
  • NAT0 between LAN and VPN interface configuration to make sure that this traffic is passed between these interface without NAT
  • Interfaces to special NAT configuration between LAN and INTERNET which would essentially transfer all traffic on the INTERNET interface (except for VPN traffic that we have handled in the previous step)

  The above things would essentially allow the VPN interface have the default route that would mean that no matter what the VPN Client source IP address it should be able to communicate with the ASA.

  The NAT0 configuration application would be to force ASA to pass this traffic between the LAN and VPN (pools) for VPN traffic.

  The special configuration of NAT then match the traffic from LAN to ANY destination address and send to the INTERNET interface. Once this decision is made the traffic would follow the lower value default route on this interface.

  I would say that this isn't really the ideal situation and the configuration to use in an environment of productin. It potentially creates a complex NAT configuration such that you use to manipulate the traffic instead of leave the mark of table routing choice in the first place.

  Of course, there could be other options, but I have to test this configuration before I can say anything more for some.

  -Jouni

• AnyConnect 3.0 supports IPSec VPN for remote access?

  Hello world

  I've read about Cisco AnyConnect 3.0 issues that it supports IPSec VPN for remote access:

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/qa_c67-622477_ns1049_Networking_Solutions_Q_and_A.html

  I downloaded and installed the Client AnyConnect Secure Mobility Client 3.0.0629, but I'm not able to get the IPSec VPN works. Also, it has no option to use the previous of Cisco IPSec VPN client PCF files.

  Can someone point me in the right direction to get IPSec VPN AnyConnect 3.0 work?

  Thank you in advance!

  Hello

  Takes AnyConnect support IPSEC from version 3.0, but only in combination with IKEv2.

  There is no option to use a CPF file with it and the config should be pushed through a profile Anyconnect.

  More information on this:

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect30/Administration/Guide/ac02asaconfig.html#wp1325361

  You should also change the ASA config so that it accepts negotiations IKE v2:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/vpn_ike.html#wp1144572

  Kind regards

  Nicolas

• Implementation of the remote access VPN IPSec using SRI 2801

  Hello

  I tried to set up a VPN for remote access using 2801 SRI. I've been able to establish my house vpn tunnel using the DSL (behind a NAT) connection, give it SRI the IP address that is in the ip pool I configured on safety. The problem I have right now is that it does not reach the company LAN network.

  DIAGRAM:

  MODEM PC (VPN CLIENT) ADSL - ROUTER SOHO - INTERNET - ISR2801 - LAN---(10.10.0.27&192.168.0.9) COMPANY

  PC: 172.16.10.122

  SOHO ROUTER LAN IP: 172.16.10.254

  SOHO ROUTER WAN IP: Dynamically assigned by ISP

  ISR2801 WAN IP: x.x.x.5/224

  IP LAN ISR2801: 10.10.0.50/24

  The CORPORATE LAN subnet: 10.10.0.0/24 and 192.168.0.9/24

  2801 SRI CONFIGURATION:

  AAA new-model

  !

  !

  connection of AAA NOCAUTHEN group local RADIUS authentication

  local NOCAUTHOR AAA authorization network

  !

  !

  IP domain name xxxxx.com

  !

  !

  !

  username root password 7 120B551806095F01386A

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto 5 40 keepalive

  ISAKMP crypto nat keepalive 20

  !

  Configuration group isakmp crypto-GROUP NOC client

  touch [email protected]/ * /! ~ $ 9876 qwerty

  DNS 192.168.0.9

  192.168.0.9 victories

  xxxxx.com field

  LWOP-pool

  include-local-lan

  netmask 255.255.255.0

  !

  !

  Crypto ipsec transform-set AC - SET esp-3des esp-sha-hmac

  !

  dynamic-map crypto NOC-DYNAMICMAP 10

  transformation-LWOP-SET game

  !

  !

  list of crypto AC-customer card NOCAUTHEN card authentication

  list of crypto isakmp NOCAUTHOR AC-card card authorization

  crypto map CNP-map client configuration address respond

  Crypto map AC - map 10-isakmp dynamic ipsec AC-DYNAMICMAP

  !

  !

  !

  !

  interface FastEthernet0/0

  IP address x.x.x.5 255.255.255.224

  Speed 100

  full-duplex

  card crypto AC-map

  !

  interface FastEthernet0/1

  IP 10.10.0.50 255.255.255.0

  Speed 100

  full-duplex

  !

  local IP NOC-POOL 192.168.250.101 pool 192.168.250.110

  IP route 0.0.0.0 0.0.0.0 XXX1

  IP route 10.10.0.0 255.255.255.0 10.10.0.10

  IP route 172.16.10.0 255.255.255.0 FastEthernet0/0

  Route IP 192.168.0.0 255.255.255.0 10.10.0.10

  IP route 192.168.250.0 255.255.255.0 FastEthernet0/0

  !

  I have attached a few screenshots. My goal here is to have access to my LAN to the company (10.10.0.0/24 and 192.168.0.9/24). I don't know what is missing here.

  No, we don't need not NAT. wanted to confirm if NAT could cause this problem.

  The config looks good. Can you ping routers ip internal interface the client LAN once it connects?

  Are correct, w.r.t. transatlantic lines reaching pool behind router VPN?

  If so, I would like to take a look at the exits following when a client is connected.

  See the crypto eli

  ISAKMP crypto to show his

  Crypto ipsec to show his

  SPSP

• Configuring remote access VPN

  Hi all

  I need help with remote access vpn configuration. I want to some remote users who have access to the internet on their system to connect and access an application server in my seat social cisco vpn client user. I use Cisco 881. I am unable to use the SDM configuration because it seems that SDM is not supported by the router so I'm using command line. I'd appreciate any help I can get. Thank you.

  This is the configuration I have:

  VPNROUT #sho run
  Building configuration...

  Current configuration: 6832 bytes
  !
  ! Last configuration change at 10:50:45 UTC Saturday, May 30, 2015, by thomas
  version 15.2
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  hostname VPNROUT
  !
  boot-start-marker
  boot-end-marker
  !
  !
  logging buffered 51200 warnings
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login userauthen1 local
  AAA authorization groupauthor1 LAN
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  iomem 10 memory size
  !
  Crypto pki trustpoint TP-self-signed-1632305899
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 1632305899
  revocation checking no
  rsakeypair TP-self-signed-1632305899
  !
  !
  TP-self-signed-1632305899 crypto pki certificate chain
  certificate self-signed 01
  3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
  69666963 31363332 33303538 6174652D 3939301E 170 3134 30313233 31323132
  33325A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36333233 65642D
  30353839 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
  8100BC0C 341CD79B A38572CE 1F0F9A91 F96B133C A889B564 E8352034 1CF5EE4B
  B505616B 6014041B EC498C0A F6C5CD2B F5BF62DA BD6E1C44 0C7B9089 1FD0C6E5
  299CEB40 28CD3F3B ADE3468A B07AAA9F AC42F0A7 4087172A 33C4013D 9A50884D
  5778727E 53A4940E 6E622460 560C F597DD53 3B 261584 E45E8776 A848B73D 5252
  92 50203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 D
  551 2304 18301680 14E85AD0 DEF133D8 E09516FD 0AA5FDAD E10EAB1A FA301D06
  03551D0E E85AD0DE 04160414 F133D8E0 9516FD0A A5FDADE1 0EAB1AFA 300 D 0609
  2A 864886 818100A 5 05050003 5B23ED5B 9A380E1F 467ABB03 BAB1070B F70D0101
  7A 218377 73089DC1 D32DA585 C5FD7ECE 0D000F96 7F3AB6CC 71509E8F 3F1C55AE
  E37536A3 1008FBF9 A29329D5 6F76DDC0 AA1C70AE 958AAE5D 32388BE4 2C1C6839
  0369 D 533 027B612C 8D199C35 C008FE00 F7E1DF62 9C73E603 85C3240A 63611D 93
  854A61E2 794F8EF5 DA535DCC B209DA
  quit smoking
  !
  !
  !
  no record of conflict ip dhcp
  DHCP excluded-address IP 10.10.10.1
  DHCP excluded-address IP 172.20.0.1 172.20.0.50
  !
  DHCP IP CCP-pool
  import all
  Network 10.10.10.0 255.255.255.248
  default router 10.10.10.1
  Rental 2 0
  !
  IP dhcp pool 1
  network 172.20.0.0 255.255.240.0
  domain meogl.net
  router by default - 172.20.0.1
  172.20.0.4 DNS server 41.79.4.11 4.2.2.2 8.8.8.8
  8 rental
  !
  !
  !
  no ip domain search
  IP domain name meogl.net
  name of the IP-server 172.20.0.4
  name of the IP-server 41.79.4.11
  IP-server names 4.2.2.2
  8.8.8.8 IP name-server
  IP cef
  No ipv6 cef
  !
  !
  license udi pid CISCO881-K9 sn FCZ1804C3SL
  !
  !
  username secret privilege 15 thomas 4 JXSizd1r/hMqPpGz94vKBb5somtpZLy03k50rJvHO6c
  username privilege 15 secret 4 mowe hlfv/rdDRCAeTUzRXbOIfdaKhJCl1onoGdaQeaQsAnw
  !
  !
  !
  !
  !
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  ISAKMP crypto client configuration group moweclients
  XXXXXXX key
  DNS 172.20.0.4
  meogl.net field
  pool mowepool
  !
  !
  Crypto ipsec transform-set esp-3des esp-sha-hmac moweset
  tunnel mode
  !
  !
  !
  Dynmap crypto dynamic-map 1
  Set transform-set moweset
  market arriere-route
  !
  !
  card crypto client mowemap of authentication list userauthen1
  card crypto isakmp authorization list groupauthor1 mowemap
  client configuration address card crypto mowemap answer
  mowemap 1 card crypto ipsec-isakmp dynamic dynmap
  !
  !
  !
  !
  !
  interface Loopback0
  IP 172.30.30.1 255.255.255.0
  IP nat inside
  IP virtual-reassembly in
  !
  interface FastEthernet0
  no ip address
  !
  interface FastEthernet1
  no ip address
  !
  interface FastEthernet2
  switchport access vlan 100
  no ip address
  !
  interface FastEthernet3
  no ip address
  !
  interface FastEthernet4
  IP 41.7.8.13 255.255.255.252
  NAT outside IP
  IP virtual-reassembly in
  intellectual property policy map route VPN-CLIENT
  Shutdown
  automatic duplex
  automatic speed
  mowemap card crypto
  !
  interface Vlan1
  Description $ETH_LAN$
  IP 10.10.10.1 255.255.255.248
  IP tcp adjust-mss 1452
  !
  interface Vlan100
  IP 172.20.0.1 255.255.240.0
  IP nat inside
  IP virtual-reassembly in
  !
  local pool IP 192.168.1.1 mowepool 192.168.1.100
  IP forward-Protocol ND
  IP http server
  23 class IP http access
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  IP nat inside source overload map route interface FastEthernet4 LAT
  IP route 0.0.0.0 0.0.0.0 41.7.8.12
  !
  access-list 23 allow 10.10.10.0 0.0.0.7
  access-list 23 allow 172.20.0.0 0.0.15.255
  access-list 100 permit ip 172.20.0.0 0.0.15.255 everything
  access-list 144 allow ip 192.168.1.0 0.0.0.255 any
  not run cdp
  !
  LAT route map permit 1
  corresponds to the IP 100
  IP 41.7.8.12 jump according to the value
  !
  route VPN-CLIENT map permit 1
  corresponds to the IP 144
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  access-class 23 in
  privilege level 15
  transport input telnet ssh
  line vty 5 15
  access-class 23 in
  privilege level 15
  transport input telnet ssh
  !
  !
  end

  Please the configuration above, give me the desired output.

  Thank you.

  Hello Thomas,.

  I'm glad to hear that you have found useful in the example configuration.

  I checked your configuration and everything seems ok with him, especially the statements of nat.

   ip local pool mowepool 192.168.1.1 192.168.1.100 access-list 100 deny ip 172.20.0.0 0.0.15.255 192.168.1.0 0.0.0.255 access-list 100 permit ip 172.20.0.0 0.0.15.255 any route-map LAT permit 1 match ip address 100 ip nat inside source route-map LAT interface FastEthernet4 overload interface Vlan100 ip address 172.20.0.1 255.255.240.0 ip nat inside ip virtual-reassembly in 

  Try to generate ICMP traffic behind your 100 VLANS to the client VPN in order to answer the following questions:

  -The router receives this traffic between VLAN100 unit?

  -The router is encrypt this traffic, after receiving the ICMP packet?

  #show crypto ipsec router its can help you with this question. Look for the program/decaps counters.

  -The same, but the other way around (from VPN client to device behind VLAN100) try to locate the problem.

  The following document explains more this crypto commands and debugs if necessary.

  http://www.Cisco.com/c/en/us/support/docs/security-VPN/IPSec-negotiation-IKE-protocols/5409-IPSec-debug-00.html#iosdbgs

• Service of ASA module does on 6509-E support remote access VPN?

  I'm having a problem of configuration of remote access VPN (SSL, Anyconnect ect.) on the Module of ASA Service on 6509-E. It is even supported or I'm wasting my time trying to do something that won't work in a first place :) to work? Site-to-Site works without any problem.

  Technical info:

  6509-E current SUP 2 t SY 15.1 (2)

  Module of ASA - WS-SVC-ASA-SM1 running of the image - asa912-smp-k8 & asdm-712

  Licenses on ASA:

  Encryption--Activated

  3DES-AES-Encryption - enabled

  Thank you for the support.

  You run multiple context mode?

  If you are, access remote VPN only is not supported in this case:

  "Note several context mode only applies to the IKEv2 and IKEv1 site to another and applies not to the AnyConnect, clientless SSL VPN, the legacy Cisco VPN, native VPN client client of Apple, the VPN client from Microsoft or cTCP for IKEv1 IPsec."

  Reference.

• Sharing screen or remote access

  Hi all.  I need some guidance on how to gain access to another Mac computer that is not on my wifi network.  My mom is a bit lost when it comes to computers and calls all the time asking questions about that or the other.  I wish I could help more, but I can't always do more in its place.  I assumed that she could do a screen with me sharing, but I did not understand that yet.  What is the best way to be able to see its screen and help her to?  I have a time machine from the airport, an Airrus SB6183 as my modem and an iMac or MBP to use.  It has an iMac.  Are our different ISP, my comcast, ATT hers.  If you could provide some info that would be great.  Thanks in advance.

  Jack

  Understand the Messages and screen sharing and test this or use some screen sharing service; Perhaps TeamViewer or an alternative, either commercial or potentially as free if the associated licenses allow your intended use.  It will be by far the best approach here.   Add the Messages application to connect and work through the sequence to accept or request required screen sharing.   Or for the

  You're probably not going to use Apple Remote Desktop (this forum), because it is a commercial product and one that is overkill for this use.   Messages and screen sharing will be sufficient, or the built-in screen sharing client can be used to share the desktop.

  Otherwise, remote access means to find a VPN and a VPN server and probably configure dynamic DNS to allow you to get the IP address of the remote site, and probably all operating in a gateway of firewall box you have acquired for the remote site.   Modems will probably have to be moved in their mode bridged, that leads them to the gap and allows your gateway box control liaison network without NAT clutter it.  ISPS are only material if they block the access of particular network involved, or do not allow the modem to be toggled in bridged mode.