Dv2700 no commissioning after recovery?

Similar Questions

• Partition lost after recovery - Satellite L30

  I had two partitions on my HD (Satellite L30-114).

  I used the Toshiba recovery Cd to restore windows back to my laptop. The CD has not offered me a full mode or an Expert as written here http://support.toshiba-tro.de/kb0/FAQ350072001GR01.htm he has just recovered without any input on my side!

  After recovery, Windows does not see my second partition. I used the disk management utility, and it is said there are 17 GB of disk unassigned space (this is my second Partition!).

  Can and how can I restore it?

  TX a lot!

  Hello

  It seems that the L30 comes with a new version of the recovery cd.
  I think that the recovery procedure is a bit different than the old with 2 different recovery modes (standard and expert)

  I know a little new recovery procedure because a friend of mine bought a new Satellite with this recovery CD. He asked me for the installation of the laptop and we checked.

  It seems that you must press the setting button after the language selection.
  If you n t use the button setting for the configuration if the recovery procedure will be remove and erase everything on the HARD drive. I think you didn't configure the settings and therefore all the partitions have been deleted.

  Unfortunately I think that there is not much to do. You the partition has been deleted and it of not possible to bring back the lost data.

• Windows does not start after recovery

  Hey, satellite 1800 started son to have more and more slow to the point where it took close to an hour to boot in Windows. It got to the stage where it seemed that recovery from the CD was the only road - so we did. Everything had to look successful from the point of view of recovery but the installer of Windows XP displays "Please wait...". "with the normal activity of the disc looking for 20-30 seconds and then hangs - no disk activity, the mouse is not responding. I went through the recovery in "expert" mode and don't see any problems with the recovery process. Issues related to the:
  1 no matter who else seen elsewhere?
  2. what else can I do diagnosis-wise?
  3 which, basically, the recovery process not / (fact he re - format partitions, could it have left a virus?)
  4. I'm better h/w or s/w diags?

  Bitshifter

  Hi Bitshifter,

  topic of your question 3:
  The recovery process replaces the whole HARD drive or even a partition with an image created by Toshiba. This image contains an operating system, drivers, and a few basic programs. All other data (including viruses) in this partition will be deleted.

  question 4:
  I don't know the cause of your problem, but I think it's a hardware problem, because after recovery, there may be incorrect or missing software.

  Sorry I can't give you more information.
  Good luck!

• Laptop HP pavilion 15-e015tx: error after recovery

  I was faced with an error when turn on PC, so I called HP support and they sent me 3 recovery disks. and I did the whole recovery process according to them. but when my pc restarts after recovery happens a screen to install the software from 1 h to 2 h and my laptop restarts several times and this screen will appear. Help, please
  
  And I do something Meanwhile process failed in the face of an error in the software installation screen

  Just be patient and wait until she finishes, it takes some time. Don't worry too much.

• Satellite M40X 299: no boot after recovery

  Hello

  I have a problem with my satellite M40. After a problem with spy software, I tried to format my pc.
  I did a restore of the system with the original cd. At the end of the mind, I pressed ctrl + alt + delete to restart as it was written.
  But nothing happens, I have only a cursor in the upper left corner of the screen and windows does not start. I did the operation 3 times and it's always the same result.

  I don't know what more I can do.

  Thanks for help.

  Excuse me for my English

  It's very strange. Can you get the CD of Microsoft facilities and try to install the OS? I'm really interested if the same thing will happen again.

  Please don't be crazy on me because I t n wrote a few exact explanation but after recovery without end I've done in the last 8 years I have never seen anything like it.

• HP plugged music after recovery?

  HP Pavilion Ultrabook 15-b005eo with 8 64-bit Windows.

  Another question for today.

  Last week, I bought this laptop yesterday I did a factory reset because HP 3D DriveGuard had ceased to work telling me that hard drives are not supported. I tried all of the solutions provided by this forum and it still does not so I decided to try the factory reset I had nothing special on my computer yet - or that's what I thought.

  As the name of 'factory reset' suggests, the computer would be re-established, on the condition that I received it in.
  Almost everything was the way I was expecting. Except Norton and HP plugged music were missing. Not a big deal for Norton can be downloaded from their site, but music connected to HP is not available from their or your site. It is not yet available from the Recovery Manager.

  I had not yet activated the trendy music trial.

  Is there a way to get this back? There should be, because it is still a new computer, and it means I have the right to 90 days of the trial, right?

  PS. DriveGuard started working again after recovery.

  Hello! Problem solved!

  Here's how it worked:

  I saw this one blogpost for the installation of Windows 8 cleanly without the 'bloatware' for computers that came with 8 Windows pre-installed. There was in the blogpost instructions to use Windows built-in 8 'reset the PC' - function to get rid of the pre-installed programs and come back only to win 8. But in the section comment each commentator said that it did not work and all (incl. "bloatware") is restored when you use this function.

  I decided to try this and it worked! Everything that has been installed on this computer is returned including HP connected with music. It's a little weird when you use Recovery Manager it does not install connected with the music but when you use the built-in function of Windows 8, it is

  I would like to especially thank Jeff who got in contact with the support e-mail client. Although they do not really have change to really help me because the weekend came gives me a change to ask two things one another, so the contact with the customer is not useless.

  Thanks again for the help and I wish you guys.

• Cannot download programs and basic games after recovery.

  Programs Application Applications Apps game games Legacy Crash crashes Hang Application Compatibility hangs

  All of a sudden we cannot download programs of basic games, after recovery we cannot not even down load dap download eccellerator!

  can help us, that's happened is that during the last 5 days.

  Hi Eric,.

  Chances are, something happened during the recovery process that prevents you from downloading something on the internet. One of the most common reasons for this is that the security settings are set too high. See the link below to learn how to change the security settings.

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-Internet-Explorer-security-settings

  Another reason that you might not be able to download whatever it is could be the settings you have enabled in your anti-virus program, if you are running one. If you are, try to disable the program while you download those

• After recovery, admin password information with 'points' and impossible to remove or change

  Hello.

  I ran yesterday, updates of Windows 7 but only those necessary.  I do not have one of those as an option.  After the updates completed, I turned on the computer and he was stuck in a loop cycle - from windows, then the admin password, connect you box came.  The box was fiiled in (with "dots" but too many to represent my password) and the screen just quickly flashed back & forth between the login screen and 'incorrect password '.     I tried to change username, and it flashed back into the admin log.

  I did a system restore to the factory settings (after saving all data) using the recovery discs.  After recovery, the screen "Set a password for the account" comes with the box below "Type a password" completely filled with dots.  I can't delete them with the BACKSPACE or DELETE key.  If I put highlight and then try to erase it with BACKSPACE or DELETE, the cursor just moves on the right side of the password box, but it is not always remove the defective "dots" password so that I can change.

  I tried to restart with the power and then switch on again.  After selecting the country & language again, same password screen developed.

  It's stuck!  Any help would be greatly appreciated!  I have computer I have is the HP Touchsmart 310 1155 - Y.

  Thank you!

  It's curious with a recovery.  First, try to reset the password using NTPassword.  Do the boot CD that him following the signs.  If this does not resolve the problem of signon, think to install the operating system from a typical drive of Windows 7 to the same version, using the key of the COA sticker.

• fqdn ping fails after recovery from sleep mode

  client system is win7 64 bit

  Server DSN is isc bind 9.7 works on win 7 64 bit

  local system of fqdn ping fails after recovery from sleep mode.

  I do not think that the ping never hits the network.

  Nslookup of full domain name or name of the system only exists.

  the system name ping only succeeds.

  then after ipconfig/release, ipconfig / renew, successor to ping the domain name full local system.

  someone at - it thoughts or ideas?

  Hello

  From the description of the problem, it seems that your computer is on a domain. I suggest you post the same question on the link below. The link given below is link TechNet Support for Windows 7. The question facing you is best for TechNet forums.

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Feel free to write us if you have any other issues related to Windows.

• How to stop a web site take over my computer and prevent Firefox from trying to find this site hurt after recovery and difficult start?

  While surfing autour, a web page false wrong (to the nonsense of cyber security-FBI-Interpol) takes over and begins to reload the same page over and over freezing all the keyboard and mouse controls. After forcing Firefox to quit, then restart, it starts to recover these same bad links. Even after using the power button to force the closure of my Mac it always tries to reload the web page devoted to the restart and launch of Firefox. Is there a way to tell Firefox to not try and retrieve the offending page or any page that was active when recovery has occurred?

  No, this does not start a circle - as soon as you leave the site with js disabled it will be gone for good...

• Satellite Pro P300-1bd - no parts sound dolby after recovery

  Hello

  I bougt garage a toshiba satellite pro P300-1bd. With this laptop, it has Dolby sound piece on the pc.

  I installed my P300-1bd with the recovery with XP disc. I've updated the pc with windows vista Enterprise edition.

  Before installing, I had an excellent sound quality, with a good bass.

  Now after you recorey, the sound is very bad.

  I installed the drivers for the card's audio fr.
  But, what should I do to get my good his return.
  I can't find sound on the internet room so that I can install it. But I don't know if that's the problem.

  Can anyone help me to get my perfect his return.

  Thank you in advance.

  Post edited by: melina

  Hello

  The European driver Toshiba page provides two audio Conexant drivers for this model of laptop.
  + Driver sound + 4.36.10.0
  + Driver sound + 4.83.1.0

  I recommend the new version 4.83.1.0
  Uninstall the old driver first in the Device Manager.

  Restart the device and install the new downloaded drivers.

  Hope this helps to get better sound quality :)

• Unassigned basic partition after recovery Qosmio X 870-11 q

  I did a cover using the two HDD Recovery and using a disc of recovery, but my score from GB 931,51 has disappeared from my computer. When I right click on my computer, manage and then go to disk management, I have a non allocated base Drive 1 with this size.

  If the partition is there but there is no drive letter or it has not been Initialised and nor has it been formatted (although I can't format which without specifying the drive letter).

  How can I get the status of change unallocated allocated and recover this drive / partition?

  Any suggestions would be welcome.

  I m wondering why it happened
  I mean after the use of the recovery disc, the unit should be set to the factory settings.
  This means that you should find the same State of HARD drive as on the first day of purchase.

  As far as I know the laptop supports an SSD drive 128 GB and a 1 TB HARD drive
  I guess the system has been installed on the SSD 128 GB drive and the 1 TB HARD drive is empty.
  This seems to be the Partition unallocated basic

  > How can I get the status of change unallocated allocated and recover this drive / partition?
  You can do it in disk management.
  Right click and create a primary partition. Now you should be able to format the partition (NTFS file format) and would be able to add a s drive letter.

• Not possible to start after recovery

  Hello

  Yesterday my Toshiba Satellite L555-110 is not stopped correctly. It looked like endless loop, while Win 7 (64 bit) showed "logout". I turned the laptop off (5 sec power button). After that, Windows is not started anymore. There was a black with a message screen as 'Please make sure that all devices such as hard disks, CD-Rom drives, etc. are well connected and try again.
  I thought that I hit the file system and started a live Knoppix CD. I tried to fix the file system with ntfsfix on each partition. This does not solve the problem, so I tried to fix Win7 with the Original Win7 from my other computer disk. In the installation menu repair tools is not started, so I had to stop the computer again.

  I thought that the problem could be the MBR after that. I searched the web and found a "command of Knoppix'"sudo testdisk"with the option"write MBR ". After trying this, the error message has changed, that the computer does not recognize the bootloader more. Here, I decided to use the recovery DVD that I created after purchasing the laptop.

  Once the recovery is finished, I tried to boot Win7, but there was a new error message (on a black screen) who told me that there are files broken in C:\Windows\system32\drivers.
  As my girlfriend has the same model of laptop computer than me, I decided to copy the folder "drivers" of his laptop (after the renaming the originial files), start knoppix, and copy it to my laptop. While trying to boot Windows with the 'safe mode' option there is no error message more appear, but now I have a hangup.
  After that I tried to install Win7 with the original disc in my other computer, but when you try to install, there is a message 'C:\$Secure' kind of broke down. Try the chkdsk command. Repair tools has not responded (infinite loop) after a few minutes of trying to find the Windows installations

  Can someone help me? I have no idea what to do at this point

  If you have two absolutely identical laptops equipped with identical hardware put HARD drive laptop s girlfriend in your laptop and try to start Windows.
  Please post the result.

• Equium A200-15I can't find wireless networks after recovery

  After making a recovery using the Vista CD from my computer (an Equium A200 15I) cannot find wireless networks. I went into the device under network adapters Manager and then there is realtek RTL8101 Ethernet NIC etc and in the other devices section it is Ethernet and controller of Stoeage of mass.

  I'm not really sure how I can get the computer to recognize and wireless networks, but I am aware that the driver is missing!

  Hello

  Try to update the wlan driver:

  http://APS2.toshiba-tro.de/WLAN/?page=downloads

  You can also check for other drivers if it is not installed:

  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp

• After recovery Windows 8 is not enabled

  Product information:

  HP TouchSmart PC ENVY 15-j013ea laptop

  I had some problems with my computer, so using HP recovery media creation I created a USB recovery key, after using it I've been able to factory reset everything, but now my windows in not activated, I talked to Microsoft but they told me to talk to HP about this, I am so confused now

  I also decided to update to windows 8.1 to see if it solves any problem, because that's what I had before the reset, but it's always the same and on the desktop, there is a message that says "Windows 8.1 Build 9600"

  Hi rikesh942010, welcome to the Forums of HP. If you are unable to find State activated with this document:Windows 8 Product Activation , you will need to contact support for assistance: North America, dial 800-474-6836 outside North America find your number here The Support of HP support

  I hope this helps.