DVD burner does not

Similar Questions

• I installed plusv15 of real players and the dvd burner does not work. It freezes and told him to put in a disc.

  I bought plusv15 real player and it has been installed. for some reason any dvd burner does not work. A pop up comes up saying wrong disc record and replace it with a new drive. I did it three times. Real player support me staff referred to you. Windows dvd burner does not work.

  Hello

  I suggest you try to execute this fixit and see if it helps:

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  I would also ask you to contact the manufacturer of your computer to check the updates of the firmware of your CD/DVD drive.

  It will be useful.

• Error message: "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged" and dvd burner does not

  Original title: dvd burner does not work can not load the driver

  I get this message "windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged.

  Can someone help me?

  Hi Garry_x,

  1. were you able to use the DVD burner before with no problems?

  2. you remember to make changes to the computer recently?

  This can occur when more than one service is defined for a device, if there is a failure at the opening of the service registry entry, or if the driver name cannot be obtained from the service registry entry.

  You can check out the following link and check for the resolution:

  http://TechNet.Microsoft.com/en-us/library/cc772156 (WS.10) .aspx

  You can also read the following article and check if it helps:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Hope this information is useful.

• DVD burner does not recognize blank dvd inserted

  DVD burner does not recognize blank dvd inserted into the pc

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• CD/dvd burner does not

  CD/dvd burner does not, tried to download the driver but nothing is made, when I try to burner anything or cd playback, nothing happens except when I try to burn a drop of water comes on saying connect burner and try again. the cd itself is rotating in the machine but it is not read then I can't play any CD at all even the drive to reinstall the driver for the cd/dvd drive. can anyone help please

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Double layer DVD burning does not

  The double-layer DVD burning does not work on my XPS420 w/vista.  The drive reads everything good and burns only 4.7 GB very well.  When you try to burn to a disc double layer blank he Burns half of the project (probably a layer), and then gives me an error message.  This happened with two different software.  Once with Roxio 10.1 included with the system and once with DVD Shrink.  I use an ISO image file appropriate.  My Player recognizes a disc blank double layer with 8 GB of free space.  During the burning process is when all else fails.  I downloaded the update of the firmware as well.  My thought is that it may be a media problem.  I virgins, disc double layer 8.5 GB DVD + R DL.  It's a brand off I've not heard of, but that was all that was available at the store.  It is a toshiba player, not sure of the model number.  16xRW +-.  Note: the front of the drive said no DL.  If all goes well they installed the correct drive.

  any thoughts?

  Thank you.

  Message edited by voiron on 2008-05-15 10:45
  
  

• HP pavilion dv6 notebook (my dvd burner does not work

  I have a hp pavilion dv6 laptop. my burner does not work. I went to the Device Manager I uninstalled, shut down the computer, restart the computer, the device mgr.enable the writer went I have little yellow guest. still, the writer does not.

  I perform a driver update, the response was: the driver is already installed is to this day. My dv6 is 28 months old.

  need some advice.

  under Device Manager.  CD-ROM/DVD-rom readers

  HP cddvdwsn-208bb

  "device usb HP dvd writer 940D thank you billy'g"

  Hello

  Try please run now from the following link:
  
  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Kind regards.

• HP Probook s 4540 DVD burner does not recognize blank disc

  Hello

  I have a 4540 s HP's Probook.  Windows 7.

  When I insert a CD or a blank DVD, it no longer recognizes.

  The Player keeps just ROAR and stop.

  Windows Media does not see disk space either.

  I downloaded and ran this fix attempt

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  And I get

  Problems found

  Matthewf

  Please see the document

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/troubleshootDisplay/?sp4ts.oid=5229455&spf_p.tpst=psiContentDisplay&spf_p.prp_psiContentDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c03280697-3%257CdocLocale%253Den_US&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  Update Sofware reboot and try burning again

  Application CyberLink PowerDVD

  http://ftp.HP.com/pub/SoftPaq/sp64501-65000/sp64647.exe

  Software CyberLink Power2Go

  FTP://www.Compaq.com/pub/SoftPaq/sp64501-65000/sp64740.exe

• DVD burner does not appear.

  List of burner windows dvd maker, no burners are shown. my cd - rw drive does not work properly.  Creation of dvd uses a different burner? How I'd get it in the list of burner?

  I have a dvd - rw drive.  It does not work properly.  On the creation of dvd, where it says choose a burner, burner was initially.  I deleted it by mistake in the list.  How can I get that back on the list so I can burn?  Thank you for answer

  ==================================================
  Sorry... I don't know exactly how to get the DVD Maker to recognize an optical drive.

  Might be interesting to try to go to Device Manager and uninstall the drive in
  issue and restart the system to see if it would reinstall it.

  Windows Vista-
  Open the Device Manager
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Device-Manager

  Good luck...

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• DVD burner does not work

  my DVD A DS8A2L-A ATA device has a code 10 and I tried micro soft Mr. fixit and I can't always burn a cd. any ideas on what to do next?

  Hi Isabelle,.

  1. did you of recent changes on the computer?

  2. what Microsoft fix it have installed on the computer?

  3. What is the version of Windows you are using?

  The Code 10 error code is generated when the Device Manager has not enough information or error that spread upwards by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

  See the Microsoft article and try the steps mentioned below.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• My CD/DVD burner does not work after installing Windows 7.

  Hello.

  I recently installed Windows 7 on my laptop (about 2 weeks ago), initially delivered with Windows Vista.

  The facility is perfectly, and I enjoyed the simplicity of the new operating system.

  Everything was going well for about 2 weeks.

  I was able to burn CDs and DVDs.

  But today, when my father asked me to burn a CD for him, Windows Media Player 12 says that I had to connect a burner and restart Windows Media Player 12.

  I restarted the program, which did not work.

  I restarted my computer, that didn't work.

  I uninstalled my CD/DVD burner drivers and reinstalled them back on and I thought that WMP12 had started working.

  But when I put the blank disc inside my laptop and started the burn, my computer gave me a message there was an error in burning the disc, and I had to close WMP12.

  When I got the farm, WMP12 and then tells me to connect a burner and restart the program.

  After that, I looked for the drivers online set to level, or to the bottom of the slope to.

  But none of them worked.

  After that, I talked with a HP technician who told me that it is better to stick to the pre-installed operating system that comes with a computer and not downgrade or upgrade manually.

  She also said that because my computer was made for Windows Vista, it was the compatible operating system for my internal hardware.

  It gives me no drivers or anything to install.

  I should have come to Microsoft first, because now I realize that HP has nothing to do with Windows 7.

  If Microsoft, I ask you:

  When you install Windows 7 on an original Windows Vista laptop and that your CD/DVD writer works for about a week, then it stops working...

  What should I do next to fix this? :(

  Please help ~!

  -Kyo

  Hey Kyo - San,

  Given that the troubleshooter could not see the CD DVD drive, you can try to navigate to the following location in the registry editor and deleted the upper filter and lower filter keys and check if it helps you get the job of CD DVD player.

  1. click on Startand then click all programs.

  2. in the start menu search box type regeditand press ENTER. If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  3. in the navigation pane, locate and then click the following registry subkey: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  4. in the right pane, look for UpperFilters and UpperFilter key and select it.
  Note You can also see an UpperFilters.bak registry entry. You don't have to delete this entry. Click UpperFilters . If you do not see the UpperFilters registry entry, you may still have to delete the LowerFilters registry entry.

  5. on the Edit menu, click delete.

  6. When you are prompted to confirm the deletion, click Yes.

  7. exit the registry editor.

  8 restart the computer.

  Note: Sometimes, this problem is due to two Windows that have been corrupted registry entries. To resolve this problem, you must use the registry editor to delete the corrupted registry entries.

  However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, follow these steps in the KB Article: http://support.microsoft.com/kb/322756/

  Access the link below to learn more about the CD-ROM drive or the DVD drive that does not work as expected on a computer.

  http://support.Microsoft.com/kb/929461

  Note: the article above is for Windows Vista and the same applies to Windows 7.

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• DVD burner does not recognize blank DVDs, but will recognize blank CD?

  I read through several similar messages, but none seem to have a solution to my problem.  I'm NOT very technically savvy, so this is as much I know:

  I have a Dimension E310

  It was supposed to come with a cd burner and a dvd burner combo.

  The reader says DVD R/RW RW DVD rewritable Compact Disk its Ultra Speed

  I was able to successfully burn CDs from itunes, but have not been able to burn any kind of video file.  In fact, when I insert a blank dvd in the drive, the computer does not recognize that everything is there.

  As I said, I'm not the person most computer savvy in the world.  I know how to work with my applications, but I know little about the way in which a computer is set up, so I apologize in advance if my question is ignorant, but I appreciate any help you can give.  Thank you in advance.

  
  

• -DVD burn does not work in the DVD player sometimes

  I have a Mac Pro from the beginning of 2008, and it came with a DVD drive (OPTIARC DVD RW AD - 7170A).  I was able to burn DVDs with using toast in the past.

  But lately, the half of the DVD burn won't play in my DVD consumer player.  I get a "Disk error" message when I try to play them, and they do not load.  It's a strange problem, because some of them work and some do not.  I can't tell where the problem is.

  Is there a way to test the DVD player?  Should I just replace it?

  Many brands of blank DVDs gives very inconsistent results when burning. If you use a brand store or generic blanks, that may be the problem.

• SD R6372 DVD burner does not recognize DVD + R

  Hey people I have a problem with my DVD writer. I bought another laptop producer but there a Toshiba ODD-DVD SD - R6372 an it worked for almost a year. now I know not what has happened, but does not recognize the drive of DVD + r. I tried DVD of 3 different manufactorers, but none worked. can you help me please?

  Thank you

  ANTY

  Hello

  Well, I don't know what can be the problem, but you can try to remove the Mr Device Manager DVD player the dvd player will be recognized again after restarting the device. However, you can check if the laser lens is dirty. If so, I propose to clean.

  Good bye

• Satellite A200 - lack of icon DVD and DVD burner does not.

  Hello

  I have a problem with my laptop Satellite A200 series. DVD/RW icon disappeared from my folder on the computer. I looked into the system folder and it says:-

  Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  I've been on the Microsoft Web site and who said to delete the driver and them click on check for changes on the hardware and it should find the new driver, but it still does not work...

  Any ideas?

  Hello

  Maybe this will help.

  [ME KLICK | http://aps2.toshiba-tro.de/kb0/TSB7801XL0000R01.htm]