DVD Super Multi (Double Layer) drive does not not in Satellite A200 - 1 M 4

Similar Questions

• Qosmio G20-126 where I can buy DVD Super Multi (Double Layer) drive?

  Hello
  Can someone help me and tell me where I can buy DVD Super Multi (Double Layer) drive
  DVD model: UJ-846-C flop in 12.7 mm
  Qosmio g20-126

  Thank you
  :)

  Hello

  Have you tried to search some online dealers that provide this part?
  In addition, you could contact a certified maintainer Toshiba in your country to order this part.

• DVD drive does not write - Satellite M40X-175

  Im having a problem with my dvd. I tried to burn my movies, music and my files on a dvdr or cdr, I tried DVD - RW and CD - RW but I do it every time gives error "d:\ is not accessible incorrect function". but when I try to watch a dvd movie or use my music cd, it does not work. He reads. Does this mean that my dvd drive cannot be read and not write?

  [Edited by: admin on 4 February 06 20:23]

  Hello

  Satellite M40X sounds new enough to have CDs of feature writing. Seems to me a HW question but you can try:
  1 - Clean the blank CD with a cloth dry
  2 - blow to the goal and do not forget that there is no dust
  3. you can uninstall the driver from
  -> Panel-> system-> hardware-> Device Manager-> DVD - RAM-> (right click) properties--> driver uninstall-> restarting your laptop.

  If they do not contribute, you can contact a Toshiba authorized Service partner. You can find the one nearest to http://217.45.123.236/toshiba/resellerselector.nsf/WebServiceProv?OpenForm

• Does not start Satellite A200 - checksum of the header file is possibly corrupted

  Does my Toshiba Satellite A200 on Vista.

  The following message appears on the screen: "the file is maybe damaged. The checksum of the file header does not match the checksum calculated.

  I tried reinstall drive, but it does not solve the problem.
  The following message is displayed: status: = xc0000428 (as well as instructions that do not seem to help at all).

  What can I do?

  Hello

  You mean that the new installation of operating system using Toshiba Recovery disk didn't?
  Hmmm, in this case, it seems like a RAM problem

  I searched a bit on the net about this error and found some info that might be linked to the faulty RAM memory.

  You should try to verify if a single one single module of RAM is affected.
  Otherwise you need to replace the two modules and then should try reinstalling the operating system.

  Welcome them

• Memory card Toshiba does not on Satellite A200

  Hello.

  When I turn on my laptop (Satellite A200) often, but not every time, I get a bar at the top of the screen that reads "Toshiba Flashcards (does not". ")"

  Sometimes this can be removed by clicking on the Red Cross in the corner of the bar and after a few moments he does not disappear, but other times it stays there and there seems to be no way to get rid of him.

  Can someone help me with this problem?
  You can probably tell from what I am not a computer expert and a simple language would be most appreciated!

  Try this:

  Updated the BIOS, which can be downloaded from the Web from Toshiba site
  Uninstall the Toshiba Value Added Package
  Download and install the latest Toshiba value added together on the Toshiba site

• Wireless communication switch does not work - Satellite A200 - 23 c

  The laptop has been included, and both a WI - Fi connection stopped working.
  Wireless communication switch does not work. Do not ask is it possible to do?

  Your English confuses me a bit little, but can you please tell me what model of laptop you have and what is the problem here?

  Wireless network card is enabled correctly in Device Manager?

• CD/DVD drive does not open satellite A210

  Hello

  I changed the Sata hard drive and installed XP. And I changed to normal again.
  Then I can't open the DVD rom.

  Please help my :(
  I installed the driver on the other hard drive. I really need your help.

  Thank you

  Hello

  If I understand correctly, you cannot open the CD/DVD drive by pressing the eject button. When the cdrom tray ejects, there is a small hol (e). Insert a PIN and the CD drive will open.

• HP DVD drive does not

  I use DVD player to my laptop for over a year and have not had a problem. All of a sudden after I've used lightscribe, some discs stopped working and a month, nothing works on my dvd player. is this a hardware problem?
  The thing that happens is when I insert a disc, the light continues to blink, but nothing appears on the icon of the drive (in Explorer)
  Data sheet: HP Pavilion dv4T - 1400
  Windows Vista 32-bit
  There is no dealer HP here and who is available is not reliable

  The underside of discs are supported by your model. Just copy the part number in the ebay search box to check what optical drive will be available here.

  part number 482175-001

  8 X drive Super Multi double layer optical drive - SATA interface, size 12.7 mm

  part number 482177-001

  8 X drive Super Multi Double Layer (DL) optical drive - with LightScribe, 12.7 mm Serial ATA compact

  part number 482181-001

  Blu - ray Disc (BD) Super-Multi Double layer optical drive

  part number 508123-001

  Blu - ray Disc (BD) SATA Super Multi Double layer optical drive

• Sat Pro L10 DVD Super Multi Drive

  I have a new Satellite Pro L10 with DVD Super Multi player running XP Pro. I was not able to write on the DVD player - either it does not recognize the DVD in the drive or it blue screens and crashes when I use the Windows backup installation until I read the error message. Now I get very nervous, I could not support the 6 weeks I got it...
  I can play the pre-recorded (of movies) DVD in the drive and it can read CDs and some brands of DVD. The manual is singularly useless on the use/troubleshooting of the Super Multi drive

  Hi Christine,

  I don't think you can use the Windows backup to record directly to CD or DVD. The following is an excerpt from the Microsoft web site: -.

  • .......... Unfortunately, the Windows backup utility cannot save files directly to a CD - RW disc.

  Have you tried the software to burn DVDs. I think that you should have Sonic RecordNow and Windvd.

  HTH

• Satellite L10 DVD Super Multi Drive - E/s of entry Error Message

  Does anyone know why, when I try to play a CD or CD-ROM, I get a box saying i/o error of entry?
  I have a Satellite L10 with a DVD super multi drive. It can read DVDs and DVD ROM

  I thought maybe it was a cable connected the drive itself, but if it's that I need how out of the car and how to support.

  I tried updating the driver and uninstall it then reinstall the drive, but I still have the same problem.
  Cannot use the accompanying software as is all the cd.

  Please can someone help me.
  Thank you

  Hello

  In most cases the entrance of e/s, error message is related to a hardware malfunction (CD/DVD drive).
  The readers of the lens laser can not calibrate properly and therefore it can not read the CD inserted.
  These errors are not uncommon and occur mostly after a long period of use due to a material stressed.

  But let's check the last possibility of solution;
  Go to Device Manager and remove the drive from the list of devices CD/DVD.
  Then start the registry (regedit) and delete the Upperfilters and Lowerfilters completely from the following registry key values:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  Then, restart the computer and check if it of possible to read CDs.

• DVD Super Multi Drive problem - cannot access any CD - Satellite A100

  Hi, 1st post:

  My Satellite A100 features a DVD Super Multi drive, which worked very well. However I cannot now access any CD - error message ' D: / is not accessible. The request could not be performed because of an i/o device error."is displayed.

  However I can still access DVDs without problem. Can anyone help?
  Thank you.

  can try this
  Right click on the drive w / the problem
  Properties
  Recording tab
  and then check the box "enable recording on this CD player.

  If this does not solve it you have Roxio Easy CD Creator is installed to check this
  http://support.Microsoft.com/default.aspx?scid=KB; EN-US; 315350

  or if you get an I/O device error message, this problem may occur when Windows tries to use a transfer mode that can not use your CD player
  RESOLUTION
  To resolve this problem, change the transfer mode for your CD drive in IDE channel properties. To do this, follow these steps:
  1. Click Start, right click my computer and then click on manage.
  2. under the (Local) computer management, click Device Manager.
  3. in the right pane, expand IDE ATA/ATAPI controllers.
  4 right-click the channel where your CD drive is connected, and then click Properties. In general, this channel is secondary IDE channel.
  5. in the Advanced Settings tab, in the zone transfer Mode for the device that represents your CD-ROM drive, click PIO only. As a general rule, this device is device 1. And then click OK.
  If the problem is not resolved after you change the transfer mode for the secondary IDE 1 channel device, your CD drive should not be located there. Use the same procedure to return to the DMA transfer mode if available. Then, repeat these steps to change the transfer mode for IDE devices in the following order until the problem is resolved:
  Primary IDE channel, device 1
  Secondary IDE channel, device 0
  Channel IDE primary note, device 1 is connected to your boot disk. It's the hard drive that contains your operating system.

  hope that fix you :)

• Satellite L50D-B - faulty DVD drive does not recognize discs

  Bought 2 months ago. The reader agrees not the CD, DVD or anything like that.
  The name of the drive does not appear on the disc and if you double click on the DVD drive icon (even if a disc is inserted) the drawer opens and says please insert a disk. I tried several discs are not the issue.

  So far I got technical support where I bought it.
  They said to do a reinstall I did - with the full drive clean. I tried to update the drivers, but the computer insists on the fact that they are later. If I search my model number on the site of Toshiba driver support he gets rejected, and I have no access to (Toshiba) drivers.

  I checked a few other forums and tried the regedit fix, but which is also irrelevant. If no solution is found (and I've lost hours of my life on this subject) then this laptop is going back for a refund and I'll get one who will perform the simple task of playing a DVD.

  Windows 8.1
  PSKUQA - 01300-S

  Hello

  Sorry to hear that you have such a stupid problem with your machine. On this virtual path, it is not easy to say what the problem is here.
  In my opinion you should not waste your time checking and search for some drivers who probably will not help at all.

  Reinstall the original operating system that you have with your machine and test functionality with the factory settings. If the result is the same contact your reseller or Toshiba service provider directly and ask for help. They can check ODD and Exchange if necessary.

• Don't burn DVD Super Multi Drive no CD

  Carpet * a DVD Super Multi Drive not burn a CD but DVD
  Burn - no problem

  Hello

  Try to remove the drive from Device Manager. After the start, the player should be recognized. Check if this procedure will solve the problem

  Good bye

• My DVD drive does not appear in Windows Explorer

  This morning my computer ran a scan virus and other things, and when this was done, my computer will not respond to any type of CD.  No DVD, CD or even disks with files stored on them.
  When I open windows Explorer, the drive from DVD (e) is not even more appear.  I was wondering how to fix this.

  Hello

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• MY CD/DVD DRIVE DOES NOT READ THE DISC READABLE

  MY CD/DVD DRIVE DOES NOT READ ANY READABLE DISK ALL OF A SUDDEN.

  I DON'T KNOW WHAT IT IS.

  I CAN HEAR THE COMPUTER TRYING TO READ BUT IT ME SAID JUST THAT HE HAS NO DISC INSERTED OR THAT THE DISC IS BLANK WHEN ITS CLEARLY NOT.

  IT would NOT be RETURNING to PLAY AUDIO CD IN iTUNES or WINDOWS MEDIA PLAYER.

  HELP PLZ

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then check the cables
  both ends. Remove and replace, do not just tight. For laptops, you can often clean power
  and contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the system manufacturer
  and the manufacturer of the device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.