Elite HPE-400y not start

Similar Questions

• HP Pavilion Elite HPE-400Y no video output.

  Hello

  I have a HP Pavilion Elite HPE-400Y computer that I had stored (unplugged) in a bedroom closet bedroom for almost a year.  It was working fine when I put it in storage.

  This past weekend, I wanted to use, so I plugged in and connected to an analog VGA monitor well known on the integrated motherboard video VGA analogue connector.  When I turned on, there is no video on the monitor.  I searched the HP support site and found a statement that said "built into the graphics card or the card PCI Express x 16 slot are usable at once; they are not usable at the same time. "This computer came with a 5450 PCI express X 16 video card installed.

  However, the 5450 PCI express X 16 video card only has a digital DVI and I wanted to use a loose analog VGA monitor.  So I powered it turned off and physically removed the 5450 PCI express X 16 video card.  Then I unplugged the power cord and removed the CMOS battery for a few minutes.  Then I replaced the battery and applied again to power.

  I still do not get all analog VGA video out of the motherboard, not even the BIOS messages it is first energized.

  I also tried to integrated edge connector with a DVI equipped, monitor.  Still, there is no video output.

  So I removed the power and re-installed the 5450 PCI express X 16 video card that has only a DVI connector.  I connected to a monitor DVI equipped and applied again to power.  There is still no video output was two well-known instructors.

  When I turn on the computer, the fan power works, processor and fans of casing run, the blue led on the switch is lit and not blinking.  The Green LED on the motherboard is on.  The Green orange and activity led Ethernet link light are on.  There are no beeps.  I can hear the hard drive starts to work.  I have no video output.

  I use a HP USB keyboard and a USB mouse.  The red LED at the bottom of the mouse is not on.  The shift lock and lock lights number do not light when you press the corresponding key.

  This computer has spent more time of storage that it has been used.  It worked even when stored in a bedroom closet in bedroom.  I checked all the wire connections on the motherboard, with no improvement.

  I would like any suggestions to get this working of the computer.  I wonder if the motherboard has somehow that went wrong.

  Thank you for your help.

  Hello Big Dave,

  Thank you for answering my question / problem.

  I am aware that I can not use an analog VGA connection on the motherboard for a digital DVI input on my LCD monitor and vice versa.  I tried two different montors both analog and digital connections on the motherboard.  I tried to communicate clearly, but I guess that I don't have.

  It is unimportant, now that I've found that HP recognizes that my computer model had a drawing or a manufacturing defect that causes the exact symptoms I am having.  There is here a link to HPs extended warranty program that describes the patterns and symptoms:

  http://support.HP.com/us-en/document/c03199423

• HP elite m9340f: do not start after replacing the video card. Repeating short and long beeps. Help!

  Hello: I have a m9340f HP Pavilion Elite aged five years, under vista. He had a problem with video output, so I bought a new video card and exchanged out them. but now, the computer does not start and made that one short beep and long stretch trying to power upward.  I double checked all connections and they are all good.

  Please help me if you know what the problem is.  Thank you... KarlJ

  I found that 1 beep short, followed by a long beep indicates a memory failure, try reinstalling your memory

• Elite 7300 does not start

  I have a problem starting with my (slightly more than 2 years) HP Elite 7300 Mt. startup stops at the screen to invent it. No response to any strike whatsoever, even the lights on the keyboard (keylock, numlock, capslock) are off and do not respond to press the keys.

  I tried to remove all THE connections from the motherboard (including the system fans), only the power and the façade remained connected, but which did not help. Put in market with all the memory removed too resulted in continuous beep (as expected). Swap memory with a newly purchased module has not solved the problem.

  Suggestions anyone?

  Hello

  Once you replace the system board, you will need to enter the feature byte and build the id in the BIOS for Windows must be enabled. This information is found on a label on the chassis.

  Please call technical support at the 18006251175 and they will guide you through the process if you have problems.

• HP 8100 elite sff does not start after upgrading processor

  I'm putting an i7 870 in a HP 8100 elite sff, but it won't start.  I get 6 beeps.  If I put the old processor in it works.  Any ideas?

  Thanks for the suggestions.  I had already updated to the latest version of the bios.  It did not help.  It turns out that when you upgrade the 8100 elite to an i7 to add a separate video card.  This is why I am getting 6 beeps.  Thanks for the help.

• HP Pavilion Elite HPE-400y: Out of control fan

  A fan in my pc starts full speed at random.  It does not matter whether I use the pc or it is just sitting and running.  Any ideas on how to stop this?  The noise is strong enough to interfere with telephone conversations.  Is there a solution?  Thank you

  Akadad, welcome to the forum.

  The first thing I suggest is to open the case and carefully clean the inside of the computer.  Dust will certainly cause the symptom you are experiencing.  Be sure to clean the fan that makes noise.  Dust on the fans will go wrong and cause noise.

  If this does not work, please let us know which fan is the source of the problem.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• A higher speed ethernet card can be installed in an hp pavilion elite hpe-400y

  Is it possible the increase in speed on ethernet and HP pavilion elite hpe400y? I would switch to 1 Gbit / s is a possiblity

  Hello

  Yes, install a 1 Gbit/s for a spare PCIe slot PCIe card will do. Driver would come with the package or downloadable from the site of the seller.

  Kind regards.

• Desktop Elite hpe 570f: broken start button (physical)

  After opening the case metal and removing the front panel, the plastic parts of the start button has been damaged and must be replaced (see image).

  I would like to buy the part and replace myslef if possible and waiting to be able to turn on my computer and use it, even if I plugged it in and nothing happened...

  Any help would be great appreciated!

  

  Here is the reference numberand a pricing example.

• Pavilion Elite m9600t will not start

  Symptoms: green light on PSU on, when the power button, fan starts briefly but turns in a few seconds, the power button / go to yellow to blue. Green light on the power supply goes off as does the light on the power button. System is then recycled; Power supply turns on, button / stop lights up blue, fan starts... Etc. no beeps. Tried to clean the dust, reset by pressing the power button / stop for 30 seconds. etc., no change. Haven't tried filing a brief and sectioning to the parties as the workspace is low. Any ideas?

  UPDATE: tried at first to replace the power supply. Apparently, this solves the problem. The computer was for two days now, so that this question should be marked resolved.

  Thanks for your reply. AS stated above, I replaced the power supply, which seems to have solved the problem.

• HP Pavilion Elite HPE-150uk - do not start

  Hi, I have a new (two weeks) HP Pavilion Elite HPE-150uk.  When I turn it on it gets insofar as the HP screen and then stops.  If I switch off and again this topic usuall starts and goes into Windows.  Although occaisionally after a reboot, I find myself with a black screen for several minutes before Windows starts.

  Is there a cure for the PC stuck on the HP screen?

  Thank you

  Robin

  Have you tried a BIOS update?

  You can always return the 150.

• HP Pavilion Elite HPE-555sc desktop PC - will not get past the first screen of the BIOS

  Hello

  Since yesterday my PC, a HP Pavilion Elite HPE-555sc desktop computer, does not start. It freezes at the start screen "HP".

  It only allows me to enter the BIOS and it meets no other entry.

  I thought it might be the motherboard.

  Is anyone know about this problem? Is it already happened?

  It comes to my PC

  My PC was already supposed to be an upgrade, but I would like to know if this can be corrected before I create a new.

  I knew no more probably is not on warranty.

  Thank you.

  Hello

  Which is usually caused by a corrupt BIOS. You can clear the CMOS. Sometimes, but not always, which solves the problem.

  It is of the card mother reference web page.

  Look for the clear instructions of the CMOS. The instructions do not specify this, but it is best to remove the RTC battery before performing the clear procedure of CMOS.

  While the RTC battery is out and the PC unplugged, press and hold the power switch of the PC for about 15 seconds. When you replace the RTC dough the + must be facing upwards.

  Best regards

  ERICO

• HP pavilion elite hpe 500cs: stuck at the start-up screen

  Hello
  I bought gtx 1060 to my hp pavilion elite hpe 500cs pc, but I can't front the start screen (cannot even get into the bios settings). I inherited bios with the latest version 7.15 which is avalible for my motherboard. The card worked on power and different Mr. b. is sufficient. I also have 1 beep, that the long break and followed 3 short and fast beeps long beep.

  Any ideas?

  Your comparison of different systems and not being is not specific about the other tested machine.  It is like comparing a Citroën with a Renault. (Could not stop myself, realizing your in CS).  The HPE 500cs, as you say, is Legacy BIOS.  The new GTX 1060 is UEFI and would not work in the HPE without a hybrid BIOS from the manufacturer of the card.

• My hp pavilion elite hpe-204f video does not work

  My hp pavilion elite hpe-204f video does not work so I replaced it with another video card that worked. After installing the card and start the system I saw the video on my monitor. Great! I need to replace my video card. No problem.

  Afer by purchasing and installing a new video card, I have no video. I put a new one in another computer. This works. I put the video card which worked yesterday... that did not work.

  Then, I put the original video card that I thought that did not work on another computer and Yes... it worked.

  Should I assume that I have a bad graphical location on the motherboard? If so, short of buying the same motherboard is there anything else I can do?

  Thank you very much for the research.

  Hello

  The integrated video processor still works when the video card is removed?  If Yes, then try this memory bootable Diagnostics CD. Download memtest86 iso file and burn the disk using Imgburn.

  If the above is successful, then re - install the map graphic and clear the CMOS.

  Another thing to try:

  A good cable video know.

  A known good monitor.

• USB ports do not respond after boot to Windows 7 - HP Pavilion Elite HPE

  I turned on a HP Pavilion Elite HPE this morning and none of the USB ports work under Windows 7.

  Mouse and USB keyboard work well in the BIOS Setup.  But after Windows starts, it is as if he found neither.

  I tried to start Windows in Safe Mode and last known good Configuration and the behavior is the same, the mouse and keyboard do not work even if they do it in the BIOS.

  I tried a different mouse and keyboard and Windows behavior is the same.

  Now, I would like to have active remote destop. Difficult to solve without an input device.

  I found a solution for Windows 7 x 64 failing to detect any USB device on all ports USB to a HP Pavilion Elite HPE-500f.

  After that backup, read and edit the registry remotely to run the utility of Microsoft Devcon registry run key, Devcon announce an error message 39 for USB hubs.  Enter 'Windows error 39 usb hub' in a search engine led me to the next web page that describes the resolution of the problem. I removed the UpperFilters also well described and restarted key and until then. -See more at: http://www.tricksguide.com/solve-device-manager-error-code-39-on-usb-controller.html

• Pavilion Elite HPE-180 t, windows 7 64 bit started to stop the sleep mode.

  Pavilion Elite HPE-180 t, windows 7 64 bit began to stop in the past few weeks.  It seems to happen from the sleep mode.  I leave the computer for more than 20 minutes, and when I come back, it is turned off.  When I start again, I have an error message and be able to start in safe mode.  I start in normal mode and I get an error "windows has recovered from an unexpected shutdown" without solution.  I also see an action center say error - consider sending additional information about a problem with the ATI display driver (graphics card is ATI Radeon HD5450 1 GB).  When I click for the solution, says that this solution could not be downloaded.  I've updated my drivers.  I haven't added a new hardware or software.

  Thanks HardBeatZ (HP).

  I did as you suggested and I had to uninstall several times because the device picked up previous ATI vs the generic drivers.  In any case it still stop with the blue screen of death when waking from sleep mode.   Then I went back and installed the latest graphics driver from the HP site for my system. I still had a few stops.

  Then I went through all my devices and checked for latest drivers.  All said that the best version is already installed.  Then I noticed that my HP bt500 bluetooth USB 2.0 adapter had only a driver available for windows 7 32 bit (I have installed 64-bit).  I used a keyboard and bluetooth mouse.   So I unplugged the adapter and have resorted to the USB keyboard and mouse and closures of blue screen stopped.  It seems that the network card was originally wake up from its sleep.  I also disabled the reactivation of LAN in the properties of the network adapter device.