Equium L350/l350D, no wireless connection option

Similar Questions

• Satellite L350 loses the wireless connection

  Can someone please help?

  I have a Satellite L350-170 which perfectly connects to the internet using a cable to connect to my router.
  When you use the wireless to connect, I can only get a connection so I first of all turn off the wireless card and then enable it again, but I lose the connection within two minutes. I can reconnect if again, I turn off and then turn on the map.

  The OS is Vista Home Premium Service Pack 2, fully implemented to date. I have updated to the most recent available wireless network driver. I tried to turn off IP6.
  The laptop is connected to the network and receives a signal of power when it connects.
  When the connection is lost, no networks are detected, but properties card says card works Ok, although Ipconfig says media disconnected. Other mobile stay connected anywhere in the House.

  Thank you in anticipation of a quick solution.

  Where did you download the latest driver for the Realtek 802.11 g (RTL8187B) wireless network card?

  This is the WLan from Toshiba portal, where you can find the latest version of the driver:
  http://APS2.toshiba-tro.de/WLAN/

  I recommend also to renew the IP address if this problem would occur.
  Cmd execute command: ipconfig / renew
  This should help to assign the new ip address

  By the way: in the Device Manager-> Wlan card-> properties-> power management, you can uncheck the mark option which disables the card in order to save energy.

  Have you tested the WiFi with open (unsecured) WiFi connection?

• Equium A100-027 - bad wireless connection

  My Toshiba Equium A100-027 has problems connecting to a wireless network.
  We have recently received Virgin broadband and it works for everyone!

  It is only wireless which is faulty, when the cable is connected it works fine.
  Is it possible to test if it's my computer or the broadband that is faulty?

  Anyone else had problems with their Wi - Fi?

  Thank you

  Hello

  You must run these common tests;
  -update the WLan driver
  -check if the WLan card is activated on this laptop. You must activate the WLan switch on the side of the laptop (LED should be on) and use the FN + F8 buttons to choose the WLan card.
  -Check the standard WLan (802. 11 A B G) local area network and router WLan card should support the same! WLan card settings can be changed in the Device Manager-> card WLan-> properties-> Advanced tab
  s ' ensure that WLan encryption is just and WiFi encryption password has been set correctly.

  Good luck

• Can not see the "wireless connection" option in the drop-down list in 'sharing' under the ics. Trying to establish an ad hoc connection.

  I'm trying to set up an ad-hoc connection between two laptops. I created a network. When I right click and select Properties. On the sharing tab, there is a check box for "allow other users to connect to this network. Below that, there is a drop down menu to "connecting home network." My problem is that I can't "wireless connection" under this sow drop andhence cannot establish a connection. Help, please! Using windows 7 64 bit home premium and have ralink 5390 adapter. I have internet through a wireless internet service provider. I use "Reliance Netconnect + wireless internet".

  Hi Amit,

  Please refer to this link and check if this helps you,

  Set up a computer-to-computer (ad hoc) network:

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-computer-to-computer-ad-hoc-network

• Vista Equium A100-027: start Wireless connection switch

  Whenever I turn on the machine it powers upward normally, but I find that the network connection has not been made. When I check, I think that the light on the wireless switch does not light even if the switch is in position "on" where I left it.

  I have the wireless switch and the new and the light and the machine connects. You have to do with the wireless switch whenever you turn on the machine? Certainly it should connect automatically if left in position one.

  Hi, I have exactly the same problem with my laptop equium A100-338, the answer to your question is Yes, the light should come back on after restart or boot closure like mine to do this, but now it is a very annoying task that I have to keep flicking the switch off then on again to get a connection.

  I'm sorry I can't be of any help on how to get the light stays on has im still waiting for an answer to this.

• Photosmart C6280: Wireless connection Option is missing from the installation all-in-one Photosmart C6280 on Windows 10

  When I was installing the complete drivers for my old C6280 Photosmart all-in-one on my new laptop Windows 10, I arrived at the place where it asks what type of connection, I have between my computer and my camera.  It provides USB and wired Ethernet in option, but there is no available wireless option, although when I click on 'Help' the third option consists of the description.  With my old laptop, I was able with print and scan wireless, so I expect to be able to do the same thing on my new laptop.  All the buttons on the installation software were grey, including the 'Back' and 'Cancel', until I made a choice, so I clicked on wired Ethernet, and buttons 'connect a printer later', hoping the third option would be there when I went to the desktop application 'Add a device' later.  No chance!

  Connect the printer via an Ethernet cable to your router and follow the installation instructions.

• I lost my wireless connection option

  I'm only connected by ethernet... Please help for windows 7

  Hi Haziqu,

  I suggest you to return the article mentioned below and see if it helps you to enable wireless on your system.

  How to enable and disable the WiFi on Windows 7 - computers mobile idea

  Keep us.

  Kind regards

• Re: Satellite S70T-A-016 - no option for wireless connection

  Greetings,

  Just picked up one new Satellite S70T-A-016. Everything worked very well last night and I had a wireless connectivity, but now, I have no option for a wireless connection. I pressed the button F 12, and the only message I get is ' airplane Mode on / off. I don't know if I pushed inadvertently something I shouldn't or not. Have connected by cable to Toshiba and updated the atheron wireless LAN and realtek drivers but still nothing. Troubleshooting only tells me to plug an Ethernet cable.

  Starting at this, so any help step by step would be appreciated. Thanks in advance

  Post edited by: jakobsprenger

  Usually, if you turn off the airplane mode WIFI should work.
  Check please follow option: move the mouse to the lower right corner and when you see options on the right, click settings. You will see the option for the WLAN. Click it and you will see the options networks. Make sure that airplane mode is DISABLED and Wi - Fi mode.

  You don't need to reinstall drivers. Laptop is preinstalled with all the necessary things and the reason for not working WLAN are bad options I think.

  Please check it out and provide feedback.

• Equium L40 - lost wireless connection

  I have an Equium L40-156 under Vista and wireless became intermittent. The switch light would go out or maybe turn on at startup. In the end, I did a restore of the entire system from scratch and installed the latest drivers (Realtek) wireless.

  This seemed to cure the problem and it has been fine for the last 2 months. However, the light is now out again (it was working an hour ago), and there is no wireless connection.

  I tried a restore of the system and also installed the latest driver from Toshiba, but I still can't run. I hesitate to start over again once it takes all day to load programs and updates. Can anyone suggest what I can do or is this another bug of Vista?

  Great news

• Wireless connection with my Equium L20

  Hello

  I recently bought an equium L20.

  I didn't know he had wirless, I use wanadoo wireless and talk and currently plugin a wireless adapter for access internet.
  When I put on the L20 it has detected my wireless connection but I can't connect to internet because it rpet aqquiring network address, but nothing more.
  I have to buy a card or something?
  Sorry to be thick but it's all new to me...

  Hello Nicola

  Please visit this page on http://www.windowsnetworking.com/j_helmig/wlan.htm WLAN. Very simply, it is described how you configure your WLAN network.

  Your device has a wireless card and you do not need to buy something.

  Good luck and if you have more questions please write again.

• All-in-one software does not provide the option of wireless connection

  I have improved my all-in-one software on my HP laptop, but when he asked how to set up the connection, there is no option for a wireless connection. There were 2 options: usb cable and ethernet cable. I chose the ethernet cable, but it does not work. Prior to this level and even now, I can print to the wireless laptop, but I can't scan.

  My configuration is:

  OK, be sure to restart and do a Windows update after you HAVE uninstalled the HP software.  Then install from the link 'Support & drivers' at the top of this page.

• I have recently reinstalled Windows 7 and now I have no option for wireless connection and wireless adapter is not (wireless connections do not show up when I go to set the new connection)

  I recently installed Windows 7 on my PC, and now when I try to set up a new wireless connection, it's impossible. My plug-and-play wireless adapter is not recognized by the computer (but he did more earlier today before installing Windows 7). NETGEAR has the appeal of Microsoft, Microsoft refused to help me for less than 80 bucks, which I can't afford, after buying their product of GD.

  So I was wondering if someone can help me? On my laptop when I go to the networks and together a new network, there is an option to set up a WIRELESS CONNECTION. Can someone help me please? I can't afford $ 80 to tell what drivers to download.

  Thanks and + karma to one who can help me solve this problem.

  Most often when a device does not work, it's because the driver has been corrupted.

  Try reinstalling your.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/

• Equium L300: can't get a wireless connection

  Hi all

  I bought a Satellite L300 PSLB2E and can't get a wireless connection. I checked the network cards and she said that working the Realtek RTL8102E Family PCI - E Fast Ethernet NIC (NDIS 6.0).
  I tried the FN + F8 but you don't receive any symbol for Wi Fi.
  I have the wireless switch to the fornt of the appliance.

  Any help much appreciated.

  Hello

  > checked network cards and she told me works the Realtek RTL8102E Family PCI - E Fast Ethernet NIC (NDIS 6.0).

  It is a LAN card and not a WLan card.
  You see a different device in the device-> Realtek RTL8187B Wireless 802 + ECS as Manager. 11b / g 54mbps USB 2.0 Network adapter +.

• Brand new C309g connect not wireless enabled wireless security options

  Printer connects via wired ethernet. I can use the http utility.

  Printer connects through secure wireless connections.

  Default printer in the autoconfig (169.xxx) when connected via WEP (both open and shared), does not connect with an IP address manually. Can't access http utility.

  Printer not autoconfig even when connected via WPA-Personal - instead only says: "no link found."

  The printer is in the clean room with the router.

  All OTHER wireless network devices work perfectly and deal with security changes.

  I have inherited the network devices that make me want to run with WEP.

  I ran the HP Network Diagnostics. It can access my router very well. It does not find the printer.

  Router is D - Link DIR-655.

  I jump through the right hoops - router to refresh, restore the default settings on the printer, etc. All other wireless network devices work correctly.

  I like to shoot a 'office space' on this brand new printer - save me please do!

  -mooi

  Oops, my mistake.  Thanks for pointing it out.

  Another idea is to make sure that the firmware is being updated on the router.

  Moreover, since the control panel of the printer: Setup > network > wireless network Test.  It will be the radio of the printer self-test.

• Re: Equium L350 - 10L - start with battery power

  I just bought an Equium L350 - 10L. When he arrived, he has been turned on using the battery and started installing Windows. However, the battery expired and I can't cross the message of "close unexpectedly" even after reboot.

  How can I go back to square one and restart the installation process? Advice.

  Oh buddy, a stupid idea. I really do not understand you. After several weeks or months in the box, maybe it makes sense that the battery cannot run with full capacity.

  In any case, connect your laptop to power supply and leave it for a while. Departure for laptop to see what will happen. If the installation process can not be finished early new laptop computer and immediately press F8. First option to choose repair my computer and follow the on-screen menu. The OS will be installed again and you will be able to complete the operating system installation process.