Error 200303 - coordination of DAQ devices

I ran into a problem with my .vi where I think several physical channels or my limited understanding of the call loops.

I've only been using LabVIEW since on November, and most of what I've learned is blunt force knowledge, so hopefully you can see what is happening in my code. Basically, I read in two encoder to measure the movement of a machine. At the same time, I want the .vi to 'watching' the encoder to understand when the device is moved from a specific distance (say 1 mm) and then read in a sample from a continuous string of tensions (I simplified the code for that matter) so that we have a measure for this point.

Previously, I had the encoders the two reading in via the DAQ Assistant and the measure of distance and the measure of angle in the code were both working. I changed using the DAQ subVIs because I thought that I needed so that I could remove another instance of the physical channel for Encoder 1 (considered as a local variable in the file). I then added the loop timed to try to tinker with it to use it as the moment the measurement. I'm sure you can figure out how I've got that put in place.

I'm not sure that this approach works, but it was my best bet. I get an error that I looked and seems to deal with the fact that the cards of the M Series DAQ cannot make calendar, but I'm not entirely sure what it means. Can someone give me please a more detailed explanation on what is happening? Don't forget, I did do that, but I want to know how it really works.

Thank you

Scott

Advertisement

I guess I don't know why you use a loop timed for that.

If I understand you correctly, you want to allow the encoder (the counter) reach a certain number, then read in an analog voltage.  Why not just watch the meter until you reach your number and then use a case either read your blood pressure (counter is the exact number) or no (counter isn't exact number)?

A bit like this:

Also, have you looked at counter provided with LabVIEW examples?  (Help for the...) Find examples... Material input and output... DAQmx... Counter measures... Position) there are some examples that show how to read a post of an encoder quadrature you might find interesting.

As for your problems with your original code, my best guess why you can't make your counter, work with your task of timed loop tasks are because you have two counters configured as inputs (so you can count the edges), but then you try to use one of them as an output (i.e. a source for your timing loop) at the same time.  I'm sure that's not possible.  A meter must be either an input or output... it can not be both.

I hope this helps.

Tags: NI Software

Similar Questions

  • daq device boot nor is not ready

    I worked with a PXI system for a long time that had a LabVIEW program in the startup folder, while running at startup.  The program used the Daq hardware to OR, and we found that he had to add a delay to the boot sequence to allow the material NOR be fully initialized before it started the program LabVIEW or the program would throw errors.

    A similar thread is at

    http://forums.NI.com/NI/board/message?board.ID=232&message.ID=6373&query.ID=1481785#M6373

    My current problem is with a LV 8.6.1 program on Windows XP.  I use a DAQ USB6212 material.  I find that I have to allow a full 60 seconds after startup before launching the program to ensure that the work of data acquisition.  If I use a 40 second delay, it works most of the time, but not always.

    I would have guessed it would be a fairly common problem.  Does anyone found a reasonable solution to this problem?  As noted in the link above, I prefer not to use arbitrary expectations.  I'd rather have a way for the operating system to start my program after that everything is ready.  But reasonable alternative will be something like the user in the other thread developed in C++: a loop that tries to access the material and keep looping until the material becomes available.  I do not think that a single Daq set call channels will work, however, because once the error occurs (in my case), restart my program is of no use.  I have to unplug the DAQ hardware and plug it in again, or restart the computer so that I can make it work.  So I need some sound more sweet, such as the type of "find resources" appeal, he has proposed.

    Kind regards

    DaveT

    Hi Dave,.

    Just a quick suggestion. I have not tested, but you might be able to do something like that at the beginning of your code:

    This loop until there is no error since the VI DAQmx device Self and then you can spend the rest of your code. Yet once again, I have not tested this in an executable to start, but I think it should work. Let me know if it helps. Thank you!

    Thanks for choosing National instruments.

    Aaron

    National Instruments

    Technical sales engineer

    http://www.NI.com/support

  • Tecra S2 - error in an I/O device if I play a DVD

    Hello
    I use a Toshiba Tecra S2 with a carpet * a DVD-RAM UJ-830 s

    Now, the problem is, when I play a CD, CD-ROM, everything works. But when I want to play a DVD I especially notice that there is an error in an I/O device.
    Then I tried to renew the driver with one that came bundled with my Tecra S2(on CD by the way) but now the same DVD that I want to play is shown as empty.

    I have recently been able to read the DVD, but now he's not playing. Can someone help me?

    Welcome them

    Hello!

    Is the CD/DVD drive listed in Device Manager correctly or you have yellow exclamation points?

    If your drive is marked with a yellow exclamation point, you must remove it from Device Manager and reboot the laptop. After that the drive will be installed again and you don t need another driver. The driver is part of the operating system.

    In addition, you must remove the upper and lower registry filters. You can find an accurate description of this document from Microsoft:
    http://support.Microsoft.com/kb/314060

    Good bye

  • Different value of USB DAQ device on different computers?

    Hello

    I have not found an answer to this one, so I open a new question. Here's the problem:

    I have a card OR USB 6003 and I read some analog signal of a sensor with a framerate of 1000 Hz (I use actually 4 analog inputs for 4 sensors). I created a VI and everything works fine on my computer. Then, I created a standalone application (.exe) and the installer that includes the drivers for the hardware DAQ and LabView Runtime Environment. When I install everything on computer target, the program works, but the sensor readings are weird! For example: I get a reading of 1 bar with a deviation of 0.02 bar on my original computer. When I plug the device on the host computer, I get an average reading of 1 bar with a gap of 0.5 bar, which is a lot! This gap could be considered some disturbances high frequency - like noise. What could be the problem? Is this even linked with LabView or is it hardware problem?

    OS information:

    Win 7, 64-bit (my computer)

    Win 7 32-bit (host)

    News of LabView:

    LabVIew 2013, version 13.0f2 (32 bit)

    OR MAX version 14.0.0f0

    Setup includes:

    NI LabView Run - Time Engine 2013 f2

    NOR-DAQmx run 14.0

    Thanks in advance on this one!

    Best regards

    Geraldine

    If you run the Test NI MAX Panel on each computer, you get the same result? Way that you specify which device to use in your code (for example MAX tasks? Project tasks? DAQmx configuration screw?) and the devices have the same configuration? Are you using the exact same device USB 6003 or use a different one on each PC?

    A computer is a desktop computer and another laptop? Economic DAQ devices are not isolated, so you could get the sound of your PC power.

  • How to fix this error: "MPT Boot ROM - no device found!"

    Ideas: my IBM Intellistation Z Pro 6221 boot from IDE hard drive. Error message "MPT Boot ROM - no deices found!" error message is displayed. Machine will start from a USCSI drive when it is connected. IDE drive is then recognized as drive D: to hard drive which does not physically OK. Normal order of BIOS. While that started from the drive SCSI Windows detects the IDE drive and after a reboot, I get a message that says that the ROM of the MPT Boot has been installed successfully. But when I disconnect the SCSI disk and then try to boot from the IDE, I again get the error "MPT Boot ROM - no device found!"

    Does anyone have a solution that will solve this problem and get the IDE drive to boot normally again?

    • You have problems with programs
    • Error messages
    • Recent changes to your computer
    • What you have already tried to solve the problem

    Remember - this is a public forum so never post private information such as numbers of mail or telephone!

    Macz51,
    Thanks for posting on the Microsoft answers Forum.  The ROM of the MPT Boot part of the SCSI controller.  So, when you disconnect the SCSI drive, you will get the error message.  If the SCSI controller is a card, you can remove it, and then check your BIOS settings to start the command and make sure that the BIOS sees your IDE drive.  If you have problems with the hardware being not recognized before it starts with Windows, then you will need to contact your OEM for support. Mike - Engineer Support Microsoft Answers
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1

    Intermittent crashes. The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1. How can I find this device? This is probably a hardware problem?

    I look at intermittent crashes, where my cursor becomes an hourglass and the system does not yet meet the ctrl-alt-delete.  In the case of a newspaper, I find

    Event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1.

    How can I determine which physical devices this is associated?  This indicates a hardware problem, or driver or firmware may be the source? The system has worked very well for a few years.  I'm not aware of any change in software that took place recently, although I have had by force, remove and reinstall iTunes earlier.

    I run SMART on all players controls and run diagnostics.  I ran chkdsk on the one I found the culprit, but not mistakes.

    Just in case it was a deadlock linked to memory, I tried to use the Diagnostics memory Microsoft on floppy, but it would not write on the disk (even if I could format and copy the files freely).

    Hello

    Go to your configuration and see which drive is for each port; 1,2,3,4...

    Then go to the Device Manager and look at how many SATA controller you have and how many ports for each, then start count from 0 to IdePort0, 1, 2, etc. for each SATA controller, so if you have 4 ports for each SATA controller, here is how you came from:

    IdePort0 1 -, 2 - IdePort1, 3 car - IdePort2 and road 4 - IdePort3 in the order of road by car

    I hope it helps

  • error message: "no audio output device is installed" I have no sound - how to rectify the problem please?

    reinstall audio devices-error message: "no audio output device is installed" I have no sound - how to rectify the problem please? tried most of the quick fix ideas, but nothing seems to work

    Hi Jammyhorse,

    1. What is the number of brand and model of the PC?

    2. when the problem started?

    3. you remember to make changes to the computer before this problem?

    Step 1:

    You can check the following link and run the Fixit and see if helps solve the problem.

    Diagnose and automatically repair audio playback problems

    http://support.Microsoft.com/mats/NO_SOUND/

    Also check out the link:

    Tips for solving common audio problems

    http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

    Step 2:

    In the BIOS settings advanced, you can also check if the onboard sound is enabled.

    You can see the manual of the system manufacturer or contact the system manufacturer for more information on how to make the changes in the BIOS.

    Note: Change to the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

    Hope this information is useful.

    Jeremy K
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • Error ""A required CD/DVD device driver is missing. " If you have a flash drive driver floppy disk, CD, DVD, or USB, please insert it now.

    OriginalTitle:lack drivers

    I change my ubuntu to Windows 7, but "A required CD/DVD device driver is missing. If you have a driver on floppy disk, CD, DVD, or USB flash drive, please insert it now. Note. If the windows installation media is in the drive, you can remove it for this step. "what I can do about it?

    Hello

    Are you able to boot to the Windows Vista operating system?

    Read the following article and see if that helps:

    Error: A required CD/DVD device driver is missing - when you boot Windows 7 or Windows Vista installation disk:

    http://support.Microsoft.com/kb/952951

  • The driver has detected an error of the controller on \Device\Harddisk1\DR1. What is the cause?

    I get this message on 7 11 windows event log IDs ' driver has detected an error in the controller on \Device\Harddisk1\DR1. "" The message keeps poping up when ever I insert my usb memory key but the DR number changes when I swap beetwhen and other memory usm drives exmp usb ports. "The driver has detected an error of the controller on \Device\Harddisk1\DR3." otherwise, my system is runnig perfect.

    Hello

    Check the drive for errors and see if it works fine it after.
    http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors
    The link above includes steps for the same.
     $C God will not look you over for medals, but for scars. Each winner has scars; I do this either on the same heart
  • The driver has detected an error of the Comptroller on \Device\Ide\IdePort3

    Hello

    I'll try to explain my problem as best as possible in chronological order then please bear with me.

    I have Windows 7 x 64.
    So last week my PC have been freezing every two days. Sometimes every day. Black screen during the games, navigation or doing any activity. Each window has frozen, the screen went black. ctrl alt del did not work no response to any entry, the only option was to restart.

    Once restarted, the system would freeze again almost immediately, and again after another reboot. Only solution was physically turn off the computer, turn off the power and wait.  After some time (5-10 min) I turn the power on and system worked very well.

    I went to the observer of events and found "the pilot detected an error of the Comptroller on \Device\Ide\IdePort3." It took place in a series starting with a per minute, then after a few minutes, two or three that occur within one minute, the frequency of this error would be gradually go back even to 10 per minute and that's where the system would freeze.

    Looking at the event viewer I thought, hold for a second I have 3 discs (Disk0 - new SSD, Disk1 - new HDD, Disk2 - old HDD) so maybe that ideport3 refers to the CDROM which I disconnected but the error has not disappeared.

    Check the BIOS settings and deleted everything that had no boot from the internal storage (so: floppy USB - disk, CDROM,)-which did not help either.

    In the Act of desperation, I unplugged my old disk (Disk2) for 6 days I have not known of IdePort3 errors and system will work very well.

    After 6 days, to my embarrassment, error returned.
    This is the story of the appearance of the error:

    10/05/2015 19:56 - after that, I unplugged old hdd
    16/05/2015-09:35
    16/05/2015 14:34
    16/05/2015 14:34
    16/05/2015 14:34
    16/05/2015 14:34
    16/05/2015 14:35
    16/05/2015 14:36
    16/05/2015 14:36
    16/05/2015 14:37
    16/05/2015 14:37
    16/05/2015 14:37
    16/05/2015-17:28
    16/05/2015-17:29
    16/05/2015-17:31
    16/05/2015-17:33
    16/05/2015-17:33
    16/05/2015-17:34
    16/05/2015-17:35
    16/05/2015-17:35
    16/05/2015-17:35
    16/05/2015-17:35
    16/05/2015-17:35
    16/05/2015-17:35
    16/05/2015-17:36
    16/05/2015-17:36
    16/05/2015-17:36
    16/05/2015-17:36
    16/05/2015-17:36
    16/05/2015-17:36
    16/05/2015-17:36
    16/05/2015-17:36
    16/05/2015-17:36
    16/05/2015-17:37 - after this system error stopped

    Here are the details of the error

    -
    -
     
      11
      2
      0
      0 x 80000000000000
     
      107016
      System
      Odin
     
     

    -
      \Device\Ide\IdePort3
      0000100001000000000000000B0004C004000000850100C00000000000000000000000000000000001000000000000000000000005100000
     

     

     
     
    Let me know if you all the news and thank you for your time in reading my number.

    I bought the card mother-GA-Z68X-UD3-B3 3 years ago. There can be no IDE ports. It has 6 SATA ports.

    Here an explanation somewhat losely formulated to work on the port that could be the culprit. Since you have 6 SATA ports, why not play the game of elimination with them?

  • How to solve 'error display driver - video playback device does not support playback of protected content?

    This message started on my installation of windows 7 media center with the installation of tuner Cable Digital ati a few months.  I had the computer in my office with no monitor for a while and watched TV through my xbox on my samsung ln52b610.  so I decided to connect to the PC directly to the tv and now get this message saying 'error display driver - video playback device does not support playback of protected content'.  the strange thing is that if I go full screen, then new Media Center, here again, it seems to go away (most of the time).  my video card is a 8500gt nvidia with hdmi output and I tried the latest driver from them and still no worky.

    Take a look at the support links that can help solve your problem.

    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-TV/protected-content-error-after-a-few-seconds-of/da074c94-e741-E011-9767-d8d385dcbb12

    http://social.technet.Microsoft.com/forums/BG-BG/w7itpromedia/thread/3eea4165-8e37-42b7-A396-62663cc516a7

    If no go, Greenbutton forum would be place to post the question: http://thegreenbutton.com/forums/

  • My Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1

    My computer (W7/64) sometimes fall to restart. I checked HD and the memory of Mrs. rescue disk - no error.
    Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1.
    The fact is that the cd-rom drive is behaving oddly. Reads the DVD of film without problem, but does not read floppy disks to install Windows (good on an another two comps).
    I therefore launched Verifier.exe and checked the other drivers. The result is dumpATA.sys is not running. (Is BTW not MS driver?).
    How can I force to load this driver?

    I checked the installation disc to compare the original version, boot.win opened, but the pilot is nowhere. Where did it come from?
    So I recorded the dump file, but the analysis of what this file is beyond my capabilities.
    Link to my file https://skydrive.live.com/redir?resid=4AF01405E5CE0354 dump! 114

    You could any body help me to find the source of my problem?

    Thank you.

    These are all good things:

    *****************************************************************************
    * *
    * Bugcheck analysis *.
    * *
    *****************************************************************************

    KERNEL_DATA_INPAGE_ERROR (7A)
    The requested page of kernel data could not be read in.  Usually caused by
    a bad block in the disk controller or paging file error. See also
    KERNEL_STACK_INPAGE_ERROR.
    If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
    This means that the disk subsystem has suffered a failure.
    If the status of the error is 0xC000009A, it means the query failed because
    a file system has failed to move forward.
    Arguments:
    Arg1: 0000000000000020, type of lock which took place (1,2,3 or PTE address value)
    Arg2: ffffffffc000009d, error state (state code of e/s normally)
    Arg3: fffffa80077f95b8, the current process (virtual address for the lock type 3 or PTE)
    Arg4: 0000000000000000, virtual address that could not be paged in (or the contents of the PTEs if arg1 is a PTE address)

    Debugging information:
    ------------------
    ERROR_CODE: (NTSTATUS) 0XC000009D - STATUS_DEVICE_NOT_CONNECTED
    DISK_HARDWARE_ERROR: Error occurred with disc material
    BUGCHECK_STR: 0x7a_c000009d
    CUSTOMER_CRASH_COUNT: 1
    DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
    Nom_processus: System
    CURRENT_IRQL: 1
    LAST_CONTROL_TRANSFER: from fffff80002c7fcac to fffff80002c8bc00
    STACK_TEXT:
    fffff880 '03578-88 fffff800' 02c7fcac: 00000000' 0000007 a 00000000'00000020 ffffffff 'c000009d fffffa80' 077f95b8: nt! KeBugCheckEx
    fffff880 '03578-90 fffff800' 02c74ba7: fffffa80 '077f9550 00000000' c000009d 00000000 00000000' fffffa80' 077f95e8: nt! : FNODOBFM: 'chain' + 0 x 50080
    fffff880 '03578b 50 fffff800' 02c7e617: fffffa80 ' 07654b 50 fffffa80 '07654ba0 fffffa80' 077f9550 fffffa80 ' 077f95b8: nt! IopCompletePageWrite + 0 x 57
    fffff880 '03578b 80 fffff800' 02c8181d: fffffa80' 07654b 50 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiDeliverApc + 0x1c7
    "fffff880 ' 03578 c 00 fffff800 ' 02c4e4fb: 00000000 00000010' fffff800 '00b 96080 00000000 00000000' fffff800' 02c229a0: nt! KiCommitThreadWait + 0x3dd
    "fffff880 ' 03578 c 90 fffff800 ' 02c229fa: fffffa80 '07654b 50 00000000 00000001' fffffa80' 069ed040 00000000' 00000000: nt! KeWaitForGate + 0xfb
    fffff880 '03578ce0 fffff800' 02f29ede: fffffa80' 07654b 50 00000000'00000000 00000000'00000080 00000000'00000001: nt! MiModifiedPageWriter + 0x5a
    "fffff880 ' 03578 d 40 fffff800 ' 02c7c906: fffff800'02e06e80 fffffa80 '07654b 50 fffff800' 02e14cc0 00000000' 00000000: nt! PspSystemThreadStartup + 0x5a
    "fffff880'03578 d 80 00000000 00000000': fffff880'03579000 fffff880 ' 03573000 fffff880 ' 03578a 80 00000000 00000000': nt! KxStartSystemThread + 0x16
    STACK_COMMAND: kb

    FOLLOWUP_IP:
    NT! : FNODOBFM: 'chain' + 50080
    fffff800'02c7fcac cc int 3
    SYMBOL_STACK_INDEX: 1
    SYMBOL_NAME: nt! : FNODOBFM: 'chain' + 50080
    FOLLOWUP_NAME: MachineOwner
    MODULE_NAME: nt
    Nom_image: ntkrnlmp.exe
    DEBUG_FLR_IMAGE_TIMESTAMP: 5147d9c6
    FAILURE_BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080
    BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080

    And this page explains what you have:
    http://msdn.Microsoft.com/en-us/library/Windows/Hardware/ff559211 (v = vs. 85) .aspx >
    (Short version of an argument 9 d: "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive.")

    It seems to intimate that it's a hardware problem rather than a driver. You say that you are having problems with the optical drive. If you log out, you still have problems to restart or boot?

    This probably isn't a memory problem, but a better method of verification, it is with Memtest86 + http://www.memtest.org/#downiso>
    Download the ISO and then create a CD with it and boot from it. If you have more than one piece of RAM, pull all but one test, then close, replace it with another and test, etc. I find it a little faster than the test at a time.

    SC Tom

  • trying to play elsword gives error that there is no device compatible 3d

    My DirectX does not work

    I play a game called Elsword and when I played Patched and the game at the end he says no. Compatible 3D devices
    So I tried my another nest of the Dragon of the game and the same problem can someone help me please...

    PS. I have download the latest Direct X and my graphics card is Intel

    Have you looked in dxdiag (Direct X Diagnostic tool) to find the make and model
    as suggested above?

    You go to the site notebookcheck and read the review of your laptop?

    "Btw im only 14 so I understand really all this other info and stuff."

    I assume you mean that you don't really understand. That's ok. You are
    never too young to learn. Just like @ 66 I'm supposed to be too old to learn
    on PC and in particular - ;) game. In fact - lol - most people think that you
    need to know more than me! ROFL

    First of all - you don't have a graphics card. Intel uses only "Integrated" graphics
    VRAM video RAM =. Video RAM is a special RAM have this graphics card
    much and the integrated graphics (chips on the motherboard or a part
    the recent Intel CPUs - AKA cpu) - do not have much of.

    Without knowing what version of the Intel HD graphics card your laptop has there
    no way to know if he can run the game, but the error message-
    "no compatible 3D device" pretty much everything says, unless you have not installed 'drivers' for your graphics card (Drivers are software that instructs the graphics processor how to process the data of the game) in which case you can still get chance once the drivers are isntalled, or update to a new version.

    .

  • My 4 GB USB shows this error "Windows has stopped this device because it has reported problems. (Code 43) ». How do slove this problem pls tell me

    My 4 GB USB shows this error "Windows has stopped this device because it has reported problems. (Code 43) ». How do slove this problem pls tell me

    Try the USB device on another computer.  If you get the same error in another computer, then the unit has probably missed and the files that it contains are lost.

  • EventID:11 - the pilot detected an error in the controller on \Device\Ide\IdePort4.

    I started getting the following error message:

    Log name: System
    Source: atapi
    Date: 16/03/2013 18:36:37
    Event ID: 11
    Task category: no
    Level: error
    Keywords: Classic
    User: n/a
    Computer: Sanja-PC
    Description:
    The driver has detected an error of the controller on \Device\Ide\IdePort4.
    The event XML:
     
       
        11
        2
        0
        0 x 80000000000000
       
        169902
        System
        Sanja-PC
       
     
     
        \Device\Ide\IdePort4
        0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000003000000000000000000000004100000
     
    The last time I had this error was for malware using ESET secruit security check. During which I got like 11 errors with event ID 11 in the observer diary of events. Next, I had warnings of ntfs with event ID: 57:
    Log name: System
    Source: Ntfs
    Date: 16/03/2013-17:24:11
    Event ID: 57
    Task category: (2)
    Level: WARNING
    Keywords: Classic
    User: n/a
    Computer: Sanja-PC
    Description:
    The system failed to flush the data in the transaction log. Corruption may occur.
    The event XML:
     
       
        57
        3
        2
        0 x 80000000000000
       
        169876
        System
        Sanja-PC
       
     
     
       
       
        0000000001000000020000003900048000000000850100C 000000000000000000000000000000000
     
    The system works fine, no freezes or crashes, but I would like to know what is the cause, is it hardware or driver related?

    Hello

    Thank you for contacting Microsoft Community.
    Since you don't face any problem while working, the system works very well. The error in the log occurred due to the error of the driver in this case. But immediately, Windows is taking measures to restore the driver, so that the system works very well. The journal entry is just a notification. During the scan, the higher the use of the disc, so the number of failures is likely to increase. It occurs even in situations where there is a transfer of files.

Maybe you are looking for

  • CD/DVD drive does not work after 8 Win instalation

    Since a month since I've updated my windows in windows 8, everything works fine but the DVD - RW. When I put the blank cd and try to open it, it gives me error when opening by saying:"windows could not complete the format". Who's a software or a hard

  • Justify on G6 Series notebook PC

    Hello My question about the warranty of the laptop. If I open the cover under the laptop computer to the hard drive, it deletes my warranty? I have found no 100% for this info.

  • On "Error5" by sending an excel file saved

    Hi, guys I encountered a problem in my vi - save test data to an excel file and then send the file. The question is when the highest level VI runs once, the program is correct, but when I use a while loop and VI tracks the second time, it will displa

  • The application was able to start (msvcp100.dll and atl100.dll not found)

    I recently to get this error when opening in 2012 of LabView. I get two different error messages. The first said "the application failed to start because MSVCP100.» DLL was not found. Re-installing this application may fix the problem. "The other mes

  • M14x R1 camera / microphone does not

    Hello I installed windows 7 on my PC and installed all the drivers present on the Dell CD, but my camera and microphone don't work anymore... I tried to install the driver: "Dell Alienware M14x caméra Firmware, v.1627, A01" but he said: "no device! I