ESXi 5.5 build 1623387 PROBLEM (purple form)

Similar Questions

• HELP: Module does not not in ESXi 5.1U1 build-1157734 / Cisco C240 M3 / NVIDIA K2 GRID 304.76

  I started a business of pension on it with VMware, but I thought I could put in place here to document the process of solving it more publicly.

  Cisco C240 M3 Server (System BIOS 1.5.3b fw version)

  Card NVIDIA K2 GRID (shipped with the server)

  VMware ESXi 5.1U1 build 1157734

  I installed the last VIB for 2 m from NVIDIA (304.76) GRID, and it installs without problem:

  ~ List of the vib # esxcli software | grep NVIDIA

  NVIDIA-NVIDIA 304, 76 - 1OEM.510.0.0.802205 of VMware_ESXi_5.1_Host_Driver VMwareAccepted 2013-09-27

  but then I try to verify installation:

  ~ # nvidia-smi

  NVIDIA: could not open the file of the device/dev/nvidiactl (no such file or directory).

  NVIDIA-SMI has failed because he could not communicate with the NVIDIA driver. Make sure that this latest NVIDIA driver is installed and running.

  Try to load the kernel module and get this:

  ~ esxcli system #.
  module - NVidia module loading

  Could not load the module/usr/lib/vmware/vmkmod/nvidia: failure

  ~ tail #-10
  /var/log/VMkernel.log

  (2013 09-27 T 02: 13:15.618Z cpu7:21007) bunch of module: initial heap size: 8388608, max heap size: 68476928

  (2013 09-27 T 02: 13:15.618Z cpu7:21007) vmklnx_module_mempool_init: Mempool max 68476928 used for the module: 75

  (2013 09-27 T 02: 13:15.618Z cpu7:21007) vmk_MemPoolCreate passed for 2048 pages

  (2013 09-27 T 02: 13:15.618Z cpu7:21007) bunch of module: using memType 2

  (2013 09-27 T 02: 13:15.618Z cpu7:21007) vmklnx_nvidia bunch of module: creation succeeded. ID = 0 x 410043000000

  NVRM: No found NVIDIA graphics card!

  (2013 09-27 T 02: 13:15.618Z cpu7:21007) nvidia could not load.

  (2013 09-27 T 02: 13:15.618Z cpu7:21007) WARNING: Elf: 2767: Kernel based the nvidia module load failed: failed < Mod_LoadDone is not >

  So I'm stuck.

  I get this error when you try to turn on a Windows 7 guest who has the added PCI device.

  

  It is configured on the host computer, but things are not quite right...

  

  anyone else facing the pleasure like this?

  -wes

  Of course, I have it works very well, but with a Quadro2k and a Quadro4k.

  Take a look in this whitepaper for instructions, be aware that it is not fully supported yet and you might have to tinker a bit to make it work.

  http://www.VMware.com/files/PDF/Techpaper/VMware-horizon-view-graphics-acceleration-deployment.PDF

• Upgrade to ESXi 4.0 Build - 398348 to ESXi 4.1

  Hello

  Currently all my servers ESXi 4.0 build 398348. vCenter server 4.1.0 Build 258902.  I also installed on my Update Manager vCenter.  What is the best way to upgrade to ESXi 4.1.  I'm new on this you can give me some instructions.

  So I've upgraded to the latest version to 4.0 before going to the 4.1?

  Thank you.

  You can directly upgrade to ESXi 4.1 using AUVS

  Check KB1022140 for differernt upgrade methods

• Cannot customize esxi 4.1 build 348481 u1

  I installed esxi 4.1 build on a dell t3500 348481 u1. Installed everything fine. I can access my esx vsphere client on the network. I want to change the name of the server and add another network card. I have restart my esx server and wait until it is completely. Gray screen that indicates the ip address and other. I do not see the "hit F2 to customize." The previous version of esxi 4.1 had this. Am I missing something?

  Welcome to the community,

  can you confirm that you look at the yellow/grey screen? Please press ALT - F2 to see if that changes anything. If not, post a picture of the screen.

  André

• Form builder compile problems (BEGINNER)

  Hello

  I am very new to ORACLE. never deal with oracle, or heard of him.

  I'll be very grateful if you guys could help me solve this problem.

  IT'S MORE FORM BUILDER ORACLE 6i.

  When I open the form compiler I get the following warnings. I don't know what to do with it. I tried searching online but no luck.

  

  

  

  As you are new to Oracle Forms, first your need to know what it is.

  Forms FAQ - Oracle FAQ

  A tutorial on Oracle9i forms and reports

  iSelfSchooling - Introduction to forms

  Form of Oracle 10 g: demos, tips, and Techniques

  Oracle-Forms-tutorial

  ---

  Creating custom Oracle Forms

  -video

  Oracle Forms Video tutorial

  To open an existing one, you need to run the form builder NOT compiler

  Hope this helps

  Hamid

• problem of form builder - intersection of the circles mating

  Hello

  Im trying to create a logo that I saw on a video - youtube logo requires paths that intersect circles 7 below for the generator of form of extract (inner triangular form) - however - I can't highlight the areas between the circles as the paths are not cut - when I really zoom in and move a circle up others move out of sync - and also - I can not move the things in detail using the arrow keys - everything seems to align with something - I turned of clicks in the transformation Panel but that solves nothing - I can reproduce the logo after many trials - surely there must be a quick way to get these interactions do - any advice would be welcome because it is a useful skill that tutorials don't seem to be enough to develop.

  

  below is a screen of the form CAP as seen in the video link youtube - how can I make it faster?

  

  https://www.YouTube.com/watch?v=hmT3QdgOgWE

  Detection of space is an option inside the live paint. You'll need when the work is not really accurate (or Illustrator just feels as if your work is not perfect).

  ColliderScribe also has an option of gap, but it is something completely different.

• ESXi 5.1 build 2000251 - unexpected host to start/stop

  A few days after the connection, the start/stop of the unexpected host.

  / var/log/vmksummary says:

  Header 1

  2014 T 02 08-21: 00:01Z heartbeat: place 15d12h44m53s, 2 mV; [[9140 worker spend 47480 KB] [10145 vmx 4194304kB] [10154 vmx 4194304kB]] [[10079 Oba - vmware_raw 8% max] [9952 sfcb-vmware_bas 14% max] [9940 Oba - pycim 20% max]] 2014 08-21 T 08: 32:28Z bootstop: host started 2014 08-21 T 08: 32:28Z bootstop: Core dump found 2014 08-21 T 09: 00:01Z heartbeat: place 0d0h28m33s, 0 mV. [[vpxa 9411-worker 12656kB] [9948 Oba-pycim 15316 kB] [9140 worker spend 44636kB]] [[10087 Oba - vmw

  /var/log/vpxa.log says:

  Header 1

  2014 08-20 T 22: 33:59.627Z [52195 B 90 verbose 'vpxavpxaInvtVm'] [VpxaInvtVm_ScheduleVmSpaceRefresh] next refresh will start in 110.333336 min 2014 08-21 T 00: 24:19.628Z [verbose 'vpxavpxaInvtVm' 522AFB90] [VpxaInvtVm_ScheduleVmSpaceRefresh] refreshing 0 VMs 2014 08-21 T 00: 24:19.628Z [verbose 'vpxavpxaInvtVm' 522AFB90] [VpxaInvtVm_ScheduleVmSpaceRefresh] next refresh will start in 127.099998 min Section for VMware ESX, pid = 9411, version = version 5.1.0 = 2000251, = exit option 2014 08-21 T 08: 32:25.245Z [FFE0E6D0 info "Default"] logging uses the fast track: false 2014 08-21 T 08: 32:25.245Z [FFE0E6D0 info "Default"] handling bora/lib logs with VmaCore facilities 2014 08-21 T 08: 32:25.245Z [FFE0E6D0 info "Default"] Manager Initialized to the handle 2014 08-21 T 08: 32:25.245Z [FFE0E6D0 "Default" error] unable to set current working directory: / var/log/vmware/vpx, N7Vmacore15SystemExceptionE (no such file or directory) 2014 08-21 T 08: 32:25.246Z [FFE0E6D0 info 'Default'] current working directory: /etc/init.d 2014 08-21 T 08: 32:25.246Z [FFE0E6D0 "ThreadPool" verbose] news feed: Min Io, Max Io, task of Min, Max Task, Max Thread, Keepalive, exit seconds idle, idle, SDS max: 2, 9, 2, 4, 13, 4, false, 600, -1 2014 08-21 T 08: 32:25.248Z [FFE0E6D0 info "Default"] log path: / var/log/vmware/vpx 2014 08-21 T 08: 32:25.248Z [FFE0E6D0 info "Default"] SSL initialization 2014 08-21 T 08: 32:25.251Z [FFE0E6D0 info "Default"] Vmacore::InitSSL: handshakeTimeoutUs = 20000000 2014 08-21 T 08: 32:25.252Z [FFE0E6D0 'VpxMutex' verbose] mutex profiling: InvtLock 2014 08-21 T 08: 32:25.254Z ['SysCommandPosix' FFE0E6D0 info] ForkExec(/usr/bin/vmware) 9415 2014 08-21 T 08: 32:25.258Z ['vpxavpxaLegacyHost' FFE0E6D0 info] [VpxaLegacyHost::LoadVMwareVersion] "vmware - v" returned: -> VMware ESXi 5.1.0 build-2000251

  I need to be able to find the problem. Any help?

  SSH (Putty) into the host.

  Go to/var/core. You will find the dump files named vmkernel - zdump.x.

  The first part of this file is readable, more party to the end step.

  Look for the the CMTF stack dump it.

  For example, search for BlueScreen.

  Post here the trace.

  Or if you have a screenshot of the purple screen. It's the same thing.

• ESXI 6.0 + Cisco c240 M4 = purple diagnostic screen.

  Hi all!

  I try to install ESXi 6.0 (custom iso fo Cisco: Vmware-ESXi-6.0.0-2494585-Custom-Cisco-6.0.0.1) on

  Cisco c240 M4 server, but it's over purple diagnostic screen. The screene shots are attached.

  

  I also tried to install the iso not personalized (VMware-VMvisor-Installer - 6.0.0 - 2494585.x86_64), and he ended up the same.

  

  History:

  I got the c240 m4, did some basic steps to set up the network and storage (it's a SATA 4 10 k 900 GB disk,

  I decided to make a raid 10 for internal storage + 60 GB flex flash for the hypervisor) and then I palanned to install the ESXi, using the KVM.

  The installation was really ssssllooowww... perhaps it takes 25 minutes and finished purple diagnostic screen.

  Have any ideas?

  The problem has been solved by remove / insert the memory card. After that, the latest firmware had been installed and ESXi 6.0 also. The subject may be close. I hope it helps someone.

• ESXi 5.5 build 2456374 is unable to reconnect to the vcenter after reboot

  Hello

  Have been hitting my head against it for the past few weeks. A host that has worked very well to a previous 5.5 build fails to reconnect to the vcenter after reboot once upgraded to build the 2456374. This also happens to the newly built guest. When a reconnection is started manually, it produces up to 80% (data of the host processing), then dies with a "general system error: internal error. I tried to remove the vpxa account, resetting the config network via the console, Cup NIC of the vswitch, removal of additional interfaces vkernel. The network via the console configuration reset allows me to reconfigure the net and tie vcenter and complete the host host configuration. However, as soon as I restart the host, is no longer, it reconnects to vcenter and I'm back where I started.

  Unfortunately, this is not a 100% event. If I rebuild a host enough times, one of the new buildings will finally works correctly.

  any ideas on how to solve this problem would be appreciated.

  Elmārs

  QUESTION REOLVED!

  Ok. so that was the easy part. Open a folder with vmware to identify the cause for this. After much digging, friction, pull hair, we found a clue in the hostd.log on the ESXi host.

  2015-04 - T 02, 04: 49:05.481Z [23381 B 70 error 'Hostsvc.NetworkProvider' user opID=HB-host-185064@917-1d029f4d-d2 = vpxuser] an error occurred during extraction of stack instance configuration: incompatible value of ccalgo for the Netstack instance: defaultTcpipStack.

  In my network performance test I did recently, I have significantly improved network iSCSI performance from the cubes NewReno network congestion control algorithm. For each of these hosts, as part of the installation procedure I now set the control algorithm of congestion on cube through the web interface. Finally, it is a little bug with that VMware believed fixed. Is not.

  To confirm doubling you encounter this problem, connect to the host (ssh or remote cli) and run the following command:

  list of esxcli ip network netstack

  You should get a message saying that there is an inconsistency in the netstack configuration.

  To fix, run the following command:

  esxcli network ip put netstack defaultTcpipStack cubic n - c

  the netstack from above list command should now display detailed information and will now be able to connect to vcenter.

  If I understand correctly, an article will be published on this in the near future.

• Problem with forms 11g

  Hi all
  I installed 11g on Win2003 R2 Forms and the facility is clean and everything works fine. The WLS_FORMS starts without a problem on port 9001 and when I asked his status through the http://localhost:9001 / forms he answers forms listener is running. My problem is that when I try to run my simple form I created by form 11g, the browser page comes with nothing in it. It shows no error message or anything that might be useful, and it does not show the form either!
  The URL that has been set in the forms preferences > DURATION is
  http://[machine_name]:9001/forms/frmservlet?config=other
  'Other' is a section of configuration in formsweb.cfg that I created to be able to run my forms from inside the form builder
  and it contains the following:
  
  [others]
  separateFrame = False
  LookAndFeel = generic
  UserID = scott/TIGER
  form = module1.fmx
  
  Does anyone have an idea?
  
  My best,
  Alireza Vali

  There are many ways in which you can host the plug-in on your own server. The easiest way would be to store the installable in the same Oracle home, in a directory that is already set up with a virtual path. For example, the directory of java forms. Then simply set up your formsweb.cfg to point to your own file rather than the distance.

  Thus, for example in 11 forms, follow these steps:

  1. download the JRE 32 bit on the Java website (http://www.oracle.com/technetwork/java/javase/downloads). For example, 1.6.0_24 is as follows: jre-6u24-windows - i586.exe

  2. copy this file to: C:\Oracle\Middleware\as_1\forms\java

  3. change the configuration of your web (formsweb.cfg) to reflect the change. So, something like this:

  jpi_classid=clsid:CAFEEFAC-0016-0000-0024-ABCDEFFEDCBA
  jpi_codebase=/forms/java/jre-6u24-windows-i586.exe#Version=1,6,0,24
  jpi_mimetype=application/x-java-applet;jpi-version=1.6.0_24
  #
  # YOU NEED TO CREATE A DOWNLOAD PAGE AND STORE IT INTERNALLY FOR NON-IE USERS
  # THE SAME METHOD COULD BE USED - STORE YOUR HTML PAGE IN THE JAVA DIR OR OTHER VIRTUALLY MAPPED LOCATION
  jpi_download_page=/forms/java/myJREdownloads.htm
  

  For anyone interested to download from a remote server, here are the necessary details for other versions:

  http://www.Oracle.com/technetwork/Java/JavaSE/AutoDownload-140472.html

  All the information above applies to earlier versions of forms too.

• Building exe problem

  When you try to build an .exe, I got the following error...

  Error 6a held at AB_Source_VI.lvclass:Close_Reference.vi-> AB_Build.lvclass:Copy_Files.vi-> AB_Application.lvclass:Copy_Files.vi-> AB_EXE.lvclass:Copy_Files.vi-> AB_Build.lvclass:Build.vi-> AB_Application.lvclass:Build.vi-> AB_EXE.lvclass:Build.vi-> AB_Engine_Build.vi-> AB_Build_Invoke.vi-> AB_Build_Invoke.vi.ProxyCaller

  Possible reasons:

  LabVIEW: File generic i/o error.
  =========================
  NOR-488: IO abandoned operation.

  Have no idea why... the vi works perfectly, but cannot generate the .exe.

  Help, please.

  I used the LabVIEW 8.x. (build Advanced Menu) file structure

  Problem sovled.

• LabVIEW 2009 Build Path problem

  [Cross posted from LAVA]

  I got a code that worked fine on my home PC, when I moved to work, the exe would not build due to errors.

  Return errors are not good to explain the problem

  Until I got this one:

  

  Look at the path of the error:

  C:\Users\Developer2\Desktop\User group Meeting\LabVIEW 2009 new features\code\02 intermediate\01 build specifications\build file executable application. exe\LabVIEW 2009\vi.lib\addons\_ICON Library\String\_icon_lib_string.llb 9.0\my paths\dist\application

  This path refers to a VI inside of my executable!

  Maybe it's a bigger problem than I first thought

  So my question is:

  If a path inside my building that would be compared to the executable and LabVIEW must resolve, could fail, this process, depending on where the exe is located in a folder hierarchy?

  I guess it could have happened before? but it would be more probable now due to longer paths!

  Cross post solution

• Firmware WRT160N ver.2 - 2.0.03 build 9 problem

  I updated the firmware (WRT160N ver.2 - 2.0.02 build 15) (WRT160N ver.2 - 2.0.03 Build 9) which is available on the site Web of CISCO and just several issues have been raised in the product and cannot go back to the old firmware. When upgrade do not have the option to save the current firmware! Would the link to download the firmware (WRT160N ver.2 - 2.0.02 build 15) that the only problem was the power of the signal. Could someone tell me where I can download? In Brazil, the support is terrible... I beleave I can solve the problem with the old firmware... You tank attention

  I'm afraid that the old firmware is no longer available on their website

• Black and white photos, impression in the purple form

  My wife has been copying some black & white family photos historical.  Six or more printed correctly, then a photo past black & white to one your purpleish to phase full of 90%, only the lower part had changed colors.  We loaded another cartridge printing black, believing that it was the cause, but to no avail.  Now all the photos to Black & white print in purple.

  Printing standard is fine.

  The copy is fine.

  The scan is fine.

  But photo printing results black & white photos in copies being 100% purple toned.

  Why?

  Printer HP 6510, only two months old.

  The printer uses color ink to print in black when printing on photo paper as the black pigmented ink is not compatible with the photo paper.  It seems that you have run out of yellow ink.  I would say the troubleshooting steps in the paper here to solve the problem.  Be sure to check the vents on the supply of yellow as the two solution.

• Problems printing forms of websites - no error message

  My HP Deskjet D1460 has suddenly developed a strange anomaly: when I try to print forms or documents to Web sites, printed text is too much, the left margin is huge, and therefore the right and lower part of the text falls clean off the page. No error message appears. It's as if the printer is magnifying the text on the page and the margins of 200%.

  I checked all the settings (fit to page and so on)-everything seems ok.

  I ran printing HP and doctor Scan and it says everything is working normally.

  A test page printed fine and I can print images or text to my files without a problem. I tried to put off the printer and turn it back on, then tried a text page of a Web site, but the "expansion text" and the enormous left margin problems persist. This applies to any web document of origin.

  UKDave wrote:

  Thanks - I should say that I use Firefox.

  When printing a Web site (I tried again), I am struck an icon 'printer' on the site itself, which does not offer a preview option, so what you suggest does not apply.

  Hello

  The following images show the real Firefox (as mentioned in my previous answer)

  

  

  Kind regards.